Search Documents

By T. Gouri Charan

Indian coals, which are of Gondwana origin, contain high amounts of mineral matter, wherein the extraneous material was intimately mixed in the coal matrix during the formation stage, causing a high level of impurity in the run-of-mine (ROM) material. These coals possess difficult to very difficult washability characteristics. Beneficiation of high-ash non-coking coals of India has become the prerequisite for improving the overall economics and efficiency of power generation. The use of dry cleaning systems in India for beneficiation of non-coking coals has gaining renewed interest recently. The benefit of the dry beneficiation process is to exploit the given resources while providing a more reliable and consistent quality fuel with a low operating cost. M/S Allmineral has introduced a technique for the dry beneficiation of coal, which is being tried in India for the treatment of high-ash non-coking coals. The first commercial air jig of 50 t/hr capacity was installed and commissioned to beneficiate high-ash coals of 40 x 5 mm feed with an ash content of 40%; a clean coal product of 33% ash was produced and is being used for a sponge iron plant.

Jan 1, 2011

By Joseph Sopko, Xavier Lacourse-Dontigny

For the REM (Réseau Express Métropolitain) project, a 2500 m tunnel was built using a tunnel boring machine (TBM) under the Montreal Pierre Elliott Trudeau Airport (ADM). Although the geology under the Montreal Airport (ADM) would have been suitable for an excavation with a hard rock machine, the rst section reuired an earth pressure balance (EPB) TBM due to the soft soil located under wetlands. After excavating 280 m, the TBM was blocked in a transition zone of unconsolidated, water-bearing soils directly above the underlying bedrock. A free air intervention was not possible due to these geological conditions. After several failed attempts to create a slurry cake for hyperbaric interventions, a ground freezing system was designed and implemented, incorporating angled pipes drilled from outside the wetlands to directly in front of the cutterhead. This paper discusses the engineering reuired to form a frozen, water-tight zone in front of the cutterhead using liuid nitrogen. It also describes the complex method of replacing the disc cutters while holding the ground freezing system active in a manner protecting the health and safety of the workers.

Jun 23, 2024

By Jameel Menashi

A process has been developed for recovering the refractory metal values contained in mixed secondary source materials such as contaminated grinding wastes, oxides and sludges. The wastes are calcined with sodium carbonate in air to convert the refractory metals to water soluble Na2CrO4, Na3V04, Na2Mo04 and Na2W04. The base metals, Fe, Ni, Co and Cu, are converted to water insoluble oxides. An aqueous leach of the calcine effectively separates the refractory metals from the insoluble base metals. Co, Ni and Cu can be recovered from the oxidic residue by conventional processing methods. The leach solution is purified and then treated to recover the refractory metals as Cr203, NH4VO3, (NH4)6Mo7024?4H2O and H2WO4. The purity of the products is sufficient for their use in many metallurgical applications. The Na+ values in the leach solution are recovered as Na2CO3(or NaHC03) and are recycled to the calcination step. It is shown that the process can accommodate a wide range of feed compositions and generates a minimum of aqueous effluents.

Jan 1, 1984

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

This paper presents the results of an investigation into the effect of pore pressure regime on the factor of safety (FS) and the anticipated critical failure mechanism for a fly ash storage facility. In this study, pore pressure measurements from standpipe piezometers and pore pressure estimated from seepage analysis were used for a comparison of the estimated FS for a fly ash slope. This comparison was applied for static and seismic scenarios. To account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation, a probabilistic analysis was performed. The slope stability analysis was conducted in 2D and 3D, adopting the limit equilibrium analysis approach, and a finite element seepage analysis. The results suggest consistency of failure surfaces for 2D and 3D and an increase in FS values of 5 percent for the 3D approach, limitations of standpipe piezometers. The study demonstrated the sensitivity of the FS value, and the implication of adopting representative material properties, and water table levels, especially in cases where limited data are available, and assumptions need to be made to assess the long-term stability of a fly ash dam facility.

Aug 1, 2024

By J. Alderman

In modern industry, cost and productivity concerns and environmental concerns are sometimes incompatible, but at other times only appear to be incompatible. Surface disposal of wastes from coal preparation plants appears to be an area of the production system with little opportunity for initiating measures which cut costs and concurrently benefit the environment. However, improving the recovery efficiency of fine coal circuitry can cost-effectively reduce the plant waste environmental burden by a substantial amount. Studies at Jim Walter Resources indicate that fine-coal waste measuring 50% ash contains over 50% recoverable, marketable coal. Modifications to the plant circuitry which reduce the amount of misplaced coal in the fine-coal waste stream could substantially reduce the volume of fine waste disposed aboveground. Studies at Jim Walter Resources indicated that episodic overloads of the vacuum filters in the fine-coal circuits at the preparation plants were a source of misplaced coal in the fine-waste stream of the cleaning plants. To improve the filtration rate and reduce overload episodes, conventional rotary blowers were replaced with high pressure air blasters on most of the filters. Subsequent testing indicated that measurable benefits can be derived from this modification.

Jan 1, 1990

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

Rutile ore is an important resource for the production of titanium products, and flotation is an efficient method to enrich rutile from its deposits. Motivated by strong commercial demand for titanium metal and alloys, substantial efforts have been made to improve the flotation efficiency of rutile. Styryl phosphonic acid (SPA) and salicyl hydroxamic acid (SHA) are commonly used as collectors for rutile flotation, and lead (Pb) ions can be used as activators for rutile flotation with SPA or SHA. Xanthates have a price advantage over SPA and SHA for the flotation of sulfides as SPA and SHA prices are higher than xanthate prices. In this work, we found that when rutile is activated by lead ions, amyl xanthate is an efficient collector for rutile flotation at pH 8. A slightly basic slurry can be readily obtained. Moreover, the price of amyl xanthate is lower than that of SPA or SHA. In this regard, this flotation strategy has the potential to be used in industry. Furthermore, the adsorption features of amyl xanthate on the Pb-activated rutile surface was investigated by experimental methods, which provides insight into the role of lead ions in rutile flotation.

By Rodolfo V. de la Cruz

This paper describes the development of a new method and device for determining the in-situ mechanical properties of rock masses. The method involves a self-recording mechanical deformation gauge for sensing-recording she deformation of the borehole wall when loaded hydraulically. The self-recording feature of the gauge eliminates the difficult technical problem of transmitting signals over very long cables for measurements at great depths. Adopting a mechanical gauge instead of electronic, electrical, optical or grid techniques eliminates delicate instrumentation and installation problems. Moreover, mechanical gauges are inherently rugged and suitable for use in severe borehole conditions including very high temperatures. The technique was tested in limestone, basalt and granite specimen. The calculated mechanical property values for 1 the tests agree with those obtained by conventional testing methods. The self-recording mechanical deformation gauge has a minimum reading of 50 micro inches (1.27 x 10-3mm), comparable with electrical resistance strain gauges, capable of reading deformations over a range of 0.25 inches (6.35mm). The sensitivity, ease and accuracy of the method recommends it highly for in-situ rock modulus measurements.

Jan 1, 1980

By Henry W. Brandt

What is the most practical method for storing a huge quantity of crude oil for a long period of time to assure availability if conditions curtail the source of supply? Underground storage is a logical answer. But can abandoned mines be used for this purpose? That is the proposal Fenix & Scisson International, Inc. submitted to the S.F.F. Association (acting in behalf of the Department of Industries of the Republic of South Africa), Johannesburg, South Africa, in October 1966. This engineering and contracting firm with headquarters in Tulsa, Oklahoma, specializes in underground storage; and based upon previous experiences their engineers were reasonably certain that a mine could be used for storing crude oil. The answer subsequently proved to be "yes." The result was con- version of a coal mine to provide storage for a quantity of crude oil which is the equivalent of a sizeable oil field. The total cost of purchasing, testing, and converting the mine was less than 15 percent of the cost of conventional steel tanks. Operating and maintenance costs are proving to be about 2 percent of those experienced at two large tank farms owned and operated by the Association.

Jan 1, 1973

By W. R. Hibbard

Emerging from discussions of U.S. energy policy: from the Project Independence Blueprint; from President Ford's statements to Congress; and from several independent appraisals of the situation; there is a clear objective to achieve an appropriate balance of supply and demand in the near term future (1) by developing more efficient ways of using energy and (2) by extending domestic sources of energy. More specifically, the strategy for achieving this goal has three parts (1) Conservation of energy through greater efficiencies in automobiles, appliances, lighting, heating, and industrial processes. (2) Increased domestic production of oil and gas through new sources such as the outer continental shelf and new efficiencies such as tertiary recovery. (3) Substitution of coal and uranium for oil and gas in utility power plants and industrial heating. The goal of energy research and development is to help achieve these goals and to help minimize the economic, environmental and social impact of our shift from imported energy to domestic sources. The focus of this paper is the implications of the expanded use of coal, and the research and development which may help achieve the above goals in so far as coal is concerned.

Jan 1, 1975

By Gerald W. Cormick

In a complex society such as ours, the range of "negotiating" relationships is constantly increasing. These negotiating relationships have emerged as a direct result of the diffusion of power or influence to new sectors and emerging concerns. Even within organizations, the myth of the authority-based heirarchical structure has given way to the reality of constant negotiations between superior and subordinate and with peers in the organizational structure. In the broader context, the corporate organization finds it necessary to reckon and often negotiate with organized employees, suppliers, buyers, government agencies and a range of organized private interests ranging from minority groups to environmental organizations. In response to this diffusion of power and the conflicts which it has engendered, a variety of conflict avoidance, conflict managing or conflict resolution techniques has developed. The purpose of this paper is to attempt to differentiate between some of the conflict intervention approaches which have appeared "on the market", and to suggest three bases for selecting among them: 1. The "role" of the conflict intervenor; 2. How far the conflict has developed; and 3. The breadth and impact of the issues involved.

Jan 1, 1979

By Nathaniel Wollman

About nine years ago the President's Materials Policy Co commission under the chairmanship of William Paley released its report entitled "Resources for Freedom." Not long ago the Senate Select Committee on National Water Resources under the chairmanship of Senator Kerr released a study entitled Water Supply and Demand. Both reports contained projections of future water user the report for 1975, and the Select Committee print for 1980 and 2000, It is my task to compare the two reports. In the initial letter from Mr. Kazmann arranging for thus session he suggested that I present "a critical evaluation of the Paley Report's section on water ?ten years later,? which might include a comparison of predicted and actual water-use rates and would spotlight the assumptions which lead to errors in the predictions , . ." It is possible to compare the results of both studies, and it possible to explain art of the differences that can be found between them. The remainder must remain shrouded in doubt, since the Paley Report did not give all details of the methods used in estimating the com¬ponents of water use.

Jan 1, 1961

By S. A. Braley

Water is our most important natural resource, for without it there is no life. It is also the principal natural resource for all manufacturing processes, in particular for the development of power. For these reasons it is essential that water be protected and conserved, with the realization that its quality 18 as important as the water itself. A significant factor in the quality of ground water is the mining of coal -- that other main ingredient of Power. In the mining of coal it is necessary to disturb the geological strata overlying or adjacent to the coal seam. This procedure not only releases water from water-bearing strata or underground aquifers but also exposes other minerals which eventually become the source of pollution or deterioration of the released water as well as of the surface stream into which It is discharged It is then evident that in attempting to utilize one essential natural resource there is degradation of the quality of the other. Many selfishly assume that the principal function of a stream is fishing and recreation, but the real function is the support of industry and agriculture upon which civilization is dependent.

Jan 1, 1959

By Connor Meinke, Shaihroz Khan, Kevin Erwin, Rajiv Chandramohan, Muhammad Usman Siddiqui

A geometallurgy study aims to link metallurgy and geology to reduce technical risk and enhance the economic performance of a mineral-processing plant. It does so by accounting for variability in a deposit to develop cash-flow models with variable throughput rates. High-quality sample selection for metallurgical test work that is representative of the deposit is an essential component of a geometallurgy study, but the large multidimensional data set makes sample selection a daunting task, as classifying the data set while respecting its heterogeneity is difficult. This paper presents a streamlined approach for sample selection, using statistical analysis techniques in Python. It cuts down time to select samples from around 1,200 s per drillhole to about 60 s for data classification and from 12 h to 8 h for handpicking samples from the classified data set, translating to cost savings. The cumulative sum method and k-means clustering method are used in the methodology to elegantly classify the data and select representative samples. The effectiveness of the methodology is demonstrated by presenting data from a prefeasibility study of a copper-iron mine in which 40 samples were selected for flotation test work.

Dec 1, 2024

By Zygmunt Sadowski

Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of chemical additives and metal ions present either added or present as contaminants, on the flotation. Fuerstenau and Palmer (1976) have studied in detail the adsorption of multivalent cations onto oxide and silicate minerals. It was observed that the adsorption of a multivalent metal species exhibits a sharp pH dependence which is related to the formation of hydroxy complexes of the metal ions in solution. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances cations such as Ca2+, Mg2+, Fe2+ and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions.

Jan 1, 1986

By Wendell H. Wiser

A comparison is presented of coal pyrolysis at temp¬eratures ranging from 4090 to 497°C and thermal dissolution of coal in tetralin at temperatures ranging from 350° to 450,°C, both utilizing a Utah high-volatile bituminous coal. The initial coal pyrolysis reactions are second order with an enthalpy of activation of 35.6 kcal per mole. The fraction of total product yield produced under second order conditions ranges from 67% at 409°C to 96% at 497°C. The process then gradually deteriorates to a first order reaction in the later stages with enthalpy of activation of 4.1 kcal, per mole. The initial reactions of solution of coal in tetralin are second order with an enthalpy of activation of 28.8 kcal per mole. The fraction of total product produced under second order conditions ranges from 63% at 350°C' to 94% at 450°C. The dissolution process then gradually changes to first order in the later stages with enthalpy of activation of 15.6 kcal per mole. A model is presented which relates the two processes and explains, the significance of the above similarities.

Jan 1, 1967

By B. Jensen, B. K. Abraham, G. J. Tuck, A. D. S. Gillies

A dust concentration meter has been developed with Australian coal industry support for the measurement of total airborne dust concentrations capable of causing explosions in underground coal mines. The instrument, The University of Queensland Dust Meter (UQDM), measures the effective dielectric constant of a mixture of coal dust and air that is drawn between the plates of a capacitor, the capacitance of which is measured by a ratio-transformer bridge and synchronous detector system. This technique measures small changes in capacitance to approximately 1 part in 106. The unique design of the capacitor sensor permits a precise volume of coal dust and air mixture to be sampled. This arrangement overcomes difficulties inherent in optical dust measurement. The meter is portable, battery powered, incorporates data logging and has intrinsic safety approval. The operation of the meter is discussed. The system is designed to monitor dust concentrations along a coal mining face and provide concentration profiles leading to the development of suppression strategies. If data from underground tests are available, the meter's potential to contribute to establishing safe working conditions underground will be discussed. Other areas of potential application of the measurement technique are also examined.

Jan 1, 1993

By W. Dresler

Since 1900, smelters have produced in Canada over 10 million tonnes of iron silicate waste slag containing significant quantities of nickel, cobalt and copper. The slag is reduced with aluminum and calcium oxide additions to produce a copper, nickel, and cobalt enriched alloy and an obsidian slag. It was found that the obsidian slag contained very low copper, nickel, and cobalt contents, indeed below 0.06% of each the base metals. These metals have been collected in a type of ferroalloy with up to 1.6% Cu, 2.1% Ni, and 0.7% Co. These alloys can be recycled according to standard procedures in base metal smelters. Surprisingly, the obsidian slag was found to display good cementitious and pozzolanic properties, which is a requirement for cement production. The strength producing properties of the obsidian slag are considered to be exceptional at the 28 day standard test age. In most cases, the obsidian concrete is characterized by significantly greater strengths than control concrete tests and concrete containing fly ash or blast furnace slag. Compressive strength data at 365 days for the obsidian concrete is impressive.

Jan 1, 2003

By J. C. Yingling, V. Badaker, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

The University of Kentucky has developed reclamation cells at a surface mine in southeastern Kentucky to evaluate the impact of spoil handling (reclamation methods) and compaction alleviation methods on the physical properties of replaced growing media and on tree survival rate. From 1997 through 2001, penetration depth, penetration resistance, bulk density, and tree survival data have been collected at the reclamation cells and correlated to determine the relationships that exist between the soil physical properties at the site and tree survival. Regression models have been developed for each reclamation method evaluated using the collected data to predict tree survival rates on reclaimed surface mined lands as a function of the soil physical properties of the replaced growing media. Procedures have been developed for handling soil/spoil during reclamation that can minimize compaction in the replaced growing media. Procedures have also been developed for alleviating compaction in growing media on reclaimed and orphaned surface mined sites. These procedures, if implemented, will increase the potential for reforestation success. Finally, procedures have been developed for collecting soil physical property data for use in evaluating the suitability of spoil conditions for reforestation.

Jan 1, 2003

By Ellen S. Forbus

Reduction bleaching is used to improve the brightness and color of the kaolin pigments sold to the paper and speciality industries. The bleach re¬duces the iron oxide associated with kaolin deposits to a colorless form by the following reaction: Na2S2O42+ 6Fe+3 + 4 H2O -> 2 NaHSO4 + 6Fe+2 + 6H+ (Conley et al., 1964). At present, sodium hydrosulfite is used by the kaolin industry as the reductive bleach. It is often purchased commercially as a liquid solution and added into an acidified slurry. Before the use of commercial sodium hydrosulfite, kaolin plants manufactured zinc hydrosulfite on site by adding zinc dust to sulfurous acid made by passing SO2 gas into water. This process was abandoned in the 1970s due to environmental concerns about zinc in waste waters. In the 1970s, Engelhard patented a process that made sodium hydrosulfate from an iron hydrosulfate (Tiethof, 1978). Difficulties with separating the iron hydroxide byproduct from the bleach and a decrease in the cost of commercial bleach caused the project to be abandoned.

Jan 1, 1993

By James T. Furey, Laurence D. Hartzog, Graham A. Karklin

A pilot plant study was conducted to evaluate the performance of column flotation in the recovery of gold from the gold/tellurides bearing sulphide ore of the Kensington deposit (Echo Bay Mines and Coeur d'Alene Mines), and to compare the performance of column flotation to conventional "mechanically agitated" flotation, Tests were conducted in a 150 mm diameter, 60 liter glass column with ground flotation feed split from a concurrently operating conventional pilot plant, thus permitting direct comparison between the two processes. During the test program, the effects of wash water rate, gas holdup, froth depth, residence time and flow bias were examined in detail. The bulk metallurgical ore sample had an average "as tested" feed grade of about 5 git gold and 1 % sulphur, with the gold occurring primarily as inclusions of montbrayite (Au2Te3) in pyrite, with minor amounts of native gold. Conventional flotation using 60 minutes residence time across four roughing stages recovered about 97% of the gold into concentrates grading about 50 g/t Au. A single stage of column flotation roughing using 25 minutes residence time matched the conventional circuit recovery of97%, but produced grades of +150 git Au.

Jan 1, 1992