Search Documents

By S. D. Van Nort

Editor’s note: This is the first of two MINING ENGINEERING articles about the Grasberg deposit. The second, focusing on open pit mine development, will appear in the April issue of the magazine. The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc. lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in the mid-1980s. Production at the open pit de- posit commenced in December 1989. The Grasberg copper-gold ore body is contained within a young igneous complex of dioritic composition that intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork. Irian Jaya comprises the western half of the island of New Guinea. The Ertsberg District lies 70 km (43 miles) inland from the Arafura Sea at an altitudeof3500 to45OOm (11,480to 14,764 ft). It straddles the Papuan fold belt. This belt forms the east-west trending chain of mountains that extend the entire length of New Guinea and is the site of numerous mineral districts.

Jan 1, 1991

By I. Fafoutis

Laboratory column studies were conducted in order to assess the effectiveness of slag and red mud reactive barriers for cleaning up leachates generated at mining and waste disposal sites and loaded with copper and manganese. Solutions containing the metals of concern were prepared by dissolving the required quantities of CuSO4?5H2O and MnSO4?H2O in distilled water so that Cu concentration was 100 ppm and Mn 20 ppm. Flow rates of 25 mL.h-1 for Cu solution and 75 mL.h-1 for Mn solution were used in order to simulate aquifer water velocities of 1 ft/d and 3 ft/d respectively. Solutions were pumped upflow, in Plexiglas laboratory columns filled with each reactive medium, using peristaltic pumps. Measurements of middle and outflow column pH, redox potential, conductivity and elements concentration were performed to provide information regarding removal mechanisms for both elements and exhaustion/inactivation rates for each reactive medium. Both reactive media showed fairly good removal efficiency over the period studied. Copper was mainly removed by precipitation and formation of Cu(OH)2 while removal of manganese was due to precipitation of Mn(OH2).

Jan 1, 2006

By Clark J. Gilbert

The mining method at the Cannon mine uses heading and bench stopes, which are subsequently backfilled with cemented high-strength fill before pillar removal. The dimensions of the pillars are 7.3 m wide by 19.8 to 28.9 m high (24 ft by 65 to 95 ft). They require careful blasting in order to not damage the rock, compromising pillar strength and complicating later removal. Additionally, the proximity of dwellings makes vibration control a must for good neighbor relations. A blast monitoring study was conducted in order to optimize bench blasting practices to maximize fragmentation, reduce costs, and to minimize wall damage and ground vibration. The Cannon mine is a joint venture between Asamera Minerals (US) Inc., a 92% owned subsidiary of Gulf Canada Ltd., and Breakwater Ltd. Asamera is the operator. The mine is located at the south end of Wenatchee, WA, a town of roughly 45,000 people on the eastern flanks of the Cascade Mountains. Gold is the primary product at the mine. The rock is extracted using a sublevel end-slicing method on 15 m (50 ft) lifts, with subsequent backfilling and pillar removal. The stope widths, dictated by rock conditions at 7.3 m (24 ft), are the same in the primaries as in the pillars, or secondaries.

Jan 1, 1990

By Bruce McKinstry

INTRODUCTION In June of 1992, the Bureau of Reclamation, United States Department of the Interior, awarded the contract for construction of the Sixth Water Aqueduct to the Fedrick-Redpath Joint Venture. This aqueduct, a segment of the Diamond Fork Power System, Central Utah Project, diverts water from Strawberry Reservoir into Sixth Water Creek and, when complete, will replace the old Strawberry Tunnel which was driven in the early 1900's. The new aqueduct is being built primarily as a result of deterioration of the old tunnel, but will also have a higher capacity and more positive control than the old tunnel as well as the capability to incorporate a turbine into the system at a later date. The Fedrick-Redpath Joint Venture is comprised of C.R. Fedrick, Inc. of Novato, California and J.S. Redpath Corporation of Tempe, Arizona. Fedrick, with its experience in pipelines and heavy construction, will construct the 4200 ft surface pipeline and flow control structure; Redpath, the managing partner, performed the underground work consisting of a 600 ft vertical shaft and 3300 ft tunnel. The project is located in the Uintah National Forest, approximately 20 miles east of Provo, Utah at a mean elevation of 7000 feet above sea level.

Jan 1, 1995

By Quan Li, Xiang Ren, De Lui, Yumin Zhang

SL-type continuous centrifugal separator with injection flow (Injection Flowing Film Centrifugation, IFFC) for separating fine and ultra-fine minerals has been developed recently in China and it is capable of recovering particles down to one micron in size. In this paper, the principle of its separation is discussed. IFFC is a special transient pulsating film which combines both thin film jigging and thin film concentration functions. It not only can intensify the looseness and stratification of the settled particles, but also create a hydraulic weir effect to improve recovery of fines and ultra- fines and significantly improve the performance of thin film separation. In a Chinese tin gravity concentrator, SL devices, SL-1200s (capacity 1.5-2.0 ton/hr) and SL-600s (capacity 0.5 ton/hr) were applied to treat -1 0 micron cassiterite slime(removed as tailings at the past) and to replace the old tin flotation system(-74+10 micron slime). The plant results show that 50-60% of the cassiterite can be recovered from -10 micron slime with an enrichment ratio of 10-12. Particle down to one micron were recovered. Under optimal conditions, the recovery from -74+10 micron slime can reach more than 85%. The recoverable size range can be determined by calculation.

Jan 1, 1995

By Brent K. Nelson, D. Lee Petersen, Charles R. Nelson

INTRODUCTION The Soudan 2 Cavern was completed in 1986 as a physics research laboratory located 713 m below ground in northern Minnesota. A paper in the 1985 RETC proceedings presented the background and planned usage for the cavern, site investigation and rock conditions, contract documents, and a bid summary. This is a follow-up paper describing construction of the cavern. The Soudan 2 excavation, 71.8 m long by 13.9 m wide by 11.6 m high, was excavated by drill and blast methods and mucked by crawler tractor and mine hoist. The excavation sequence consisted of twin top-heading pilot tunnels followed by removal of the top heading pillar and finally the bench. Various blasting designs were used to achieve adequate breakage and acceptable levels of blast damage control at the cavern perimeter. The geologic conditions exposed in the cavern, and the support needs of the rock encountered, are compared to the conditions interpreted from the site investigation. The influence of specific geologic features on cavern performance will be described. Initial support and final lining consisted of full length grouted rockbolts and reinforced and plain shotcrete. Trials were conducted with steel-fiber reinforced shotcrete and microsilica additives. The performance of the rock and support systems was tracked with single point extensometers, convergence measurements

Jan 1, 1987

By Walker Ian W., John D. Gow

The paper describes the exploration and development activity associated with a series of open pit gold deposits in the Laverton region of Western Australia with an aggregate resource base of 4 million tonnes at a grade of about 3 grammes per tonne. In September 1988, Hill Minerals N.L., now a wholly owned subsidiary of Ashton Mining Limited, completed the purchase of the Cork Tree Well treatment plant from Austwhim. This CIP plant had a rated capacity of 235,000 tonnes per annum, and is located within the Hill Minerals Laverton Project area. Ore is trucked by haulage contractors from each open pit mine to the central treatment plant at Cork Tree Well. Studies were completed and a plant expansion undertaken lifting throughput to 500,000 tonnes per annum. A contract was let for this expansion in November 1988, and construction completed in April 1989. Concurrent with the above project development work, heap leach metallurgical studies are being undertaken on low grade mineralisation associated with higher grade ore zones at several of the open pit mines, notably King of Creation and Craiggiemore. It is anticipated that heap leaching will provide a useful adjunct to gold production from milling higher grade ores.

Jan 1, 1989

By Haydn H. Murray

The three major catalyst markets that utilize industrial minerals as raw materials are petroleum refining, chemical processing, and emission control. Because of economic, competitive, and regulatory pressures, catalyst producers are pushed to develop products with improved performance to meet changing environmental standards. Also, refiners are demanding new families of cracking catalysts that will crack residual fuels. In 1987, worldwide cracking catalyst sales amounted to $457 million (Occelli, 1988a). Recently enacted federal and state laws to improve air quality have prompted strong growth for environmental catalysts, which in 1989 accounted for more than a third of the $1.9 billion catalyst market in the United States (Farrauto, Heck, and Speronello, 1992). A catalyst is a material that promotes or enhances a chemical reaction but does not itself enter into the reaction. One of the more important mineral groups used as catalysts is clays. The first recorded use of clay as a catalyst was its use in the dehydration of alcohol (Bondt et al., 1797). Clay minerals that are used as catalysts are kaolinite, halloysite, smectite, palygorskite, and sepiolite. Minerals used as catalysts, catalyst supports, or as a raw material to make zeolites are kaolinite, halloysite, sodium montmorillonite, calcium montmorillonite, hectorite, palygorskite, sepiolite, talc, calcined kaolinite, gibbsite, chlorite, and titanium dioxide.

Jan 1, 1994

By R. Vance, C. Cho, N. Mardi, Z. Qian, K. Prisbrey

One problem with the application of neural networks to the multivariable control of mineral and extractive processes is determining whether and how to use them. The objective of this investigation was to compare neural network control to more conventional strategies and to determine if there are any advantages in using neural network control in terms of set-point tracking, rise time, settling time, disturbance rejection and other criteria. The procedure involved developing neural network controllers using both historical plant data and simulation models. Various control patterns were tried, including both inverse and direct neural network plant models. These were compared to state space controllers that are, by nature, linear. For grinding and leaching circuits, a nonlinear neural network-based model predictive control strategy was superior to a state space-based linear quadratic gaussian controller. The investigation pointed out the importance of incorporating state space into neural networks by making them recurrent, i.e., feeding certain output state variables into input nodes in the neural network. It was concluded that neural network controllers can have better disturbance rejection, set-point tracking, rise time, settling time and lower set-point overshoot, and it was also concluded that neural network controllers can be more reliable and easy to implement in complex, multivariable plants.

Jan 1, 1998

By R. D. Miller, D. W. Steeples

Application of shallow, seismic reflection to problems associated with mineral exploration, mine planning, abandoned-mine detection and environmental evaluation has been successful in many geologic settings. The increased dynamic range of recording equipment and the decreased cost of processing hardware and software have made shallow, seismic reflection a cost-effective means of imaging geologic targets significant to mining operations. Seismic data possess sufficient resolution in many areas to detect faulting with displacement of less than 3 m (10 ft) in coal seams as thin as 2 m (6.5 ft) at depths of 200 m (655 ft). Subsurface voids associated with abandoned mines at depths of less than 20 m (65 ft) can he detected and mapped. Seismic reflection has been successful mapping disturbed subsurface associated with dissolution mining of salt. Complex geologic features associated with deposition of various hydrothermal minerals have been mapped with high-resolution seismic reflection at depths from 80 m (260 ft) to more than 300 m (985 ft). Faults in sulfur-hearing cap rock over salt domes have been accurately located, allowing improved efficiency of the dissolution mining process. Shallow, high-resolution seismic reflection has the potential to enhance the economics and safety of mine operations.

Jan 1, 1996

By Erich U. Petersen

Discussion by Erich U. Petersen Harbuck et al. (1990) present results of research on sulfuric acid leaching of a germanium-gallium ore and shed considerable insight on possible extraction methods for gallium and germanium. However, the presentation does not give sufficient details to evaluate the research, so some of the conclusions may not be as applicable as stated. The objective of this communication is to indicate that relevant and easily obtainable geological and technical information was omitted. Consequently, on this basis, alternative explanations for some of the data are possible. Discussed below are the omission of: • pertinent geological, mineralogical and geochemical literature; • details regarding the determination of germanium concentration in quartz by electron microprobe; and • details on the calculation of the amount of germanium locked in quartz. "These topics are important since the determination of the amount and locus of "unrecoverable, locked germanium" may have an important impact on the economics and methods of germanium extraction and the directions of future research. Harbuck et al. state that "A key to increasing germanium extraction is understanding the mineralogy of the ore." However, only two studies are cited that in some manner describe the mineralogy of the ores. In addition, both of these studies were very preliminary, of limited scope and examined very few

Jan 1, 1993

By J. A. Procarione, M. K. McCarter, Bradley C. Paul

A numerical technique is described which can be used to model the quantity and distribution of air flow through broken rock. The method can also describe gas concentration and temperature distribution. A computer code implementing the numerical approach was developed to assist in determining the feasibility of a proposed modified in-situ leaching method for extracting copper from sulfide porphyry deposits. This mining method requires air to be forced through cells of rubblized ore. The flow serves to supply oxygen for the leaching reactions and to dissipate heat that would other-wise build due to the exothermic reactions. The method substitutes the Carman equation into the Laplace equation. The solution of the resulting non-linear formulation is done on a finite difference grid using SOR with iteration improvement of coefficients. This procedure yields the required air flow pattern and pressure drop. An equation for advection with absorption is then solved over the same grid using explicit schemes to yield oxygen concentration. Finally, a similar technique is applied to the convective heat transfer formula to yield the temperature profile. The model is potentially applicable to such mining problems as the prediction of leakage through caved ground, the prediction of methane concentration in gobbed ground, and the prediction of heat build-up in caved workings.

Jan 1, 1989

By C. K. Lee

The influence of passageway fires on ventilation flows was investigated in three horizontal fire tunnel s: 1. a laboratory-scale fire tunnel network, 2. a small-scale fire-plume tunnel, and 3. a large- scale simulated mine gallery. Wood was used in the first and third tunnel and gas-burners were used in the second one to generate passageway fires. Experimental measurements included gas mass flow rate, velocity, temperature and pressure in the passageways and exhaust fans. The overall and local effects of the fires were investigated by comparing these measurements obtained before and during the fires. Results show that a passageway fire essentially increases the flow resistances of the passageways of a tunnel flow network by virtue of volatile fuel mass injection and high combustion temperatures. The ventilation air flow rate is consequently throttled to lower values than that before the fire. At severe throttling, reverse flow occurs. Conditions for reverse flow are characterized by two Froude numbers based on gas velocity and density upstream of the fire, and height of the passageway. The Froude numbers and the characteristics of the passageway fire are necessary to analyze mine ventilation/fire interaction and to predict mine ventilation patterns during fires.

Jan 1, 1980

By J. A. Brierley, C. L. Brierley, R. C. II Blake, S. McGinness

A principal long-term goal of this laboratory is to achieve a detailed understanding at the molecular level of the microbial-dependent solubilization of minerals. Three recent advances in this research are summarized. (i) An in situ electrolytic procedure is described whereby large quantities of autotrophic iron-oxidizing organisms may be achieved for fundamental or applied studies. Over 600 grams wet weight of Thiobacillus ferrooxidans were harvested from a single 55-gallon growth vessel. (ii) A basis is presented for classifying some 70 different iron-oxidizing bacteria into one of 4 categories, depending on the type of redox-active electron transport proteins expressed during aerobic respiration on reduced iron. Comparative spectroscopic analyses indicated that different electron transport mechanisms exist in different genera and species of acidophilic bacteria that respire on iron. (iii) A method is introduced to investigate the binding interaction between bacteria and minerals, based on changes in the electrokinetic properties of the two species. Preliminary experiments indicated that the electrophoretic mobilities of pyrite and Thiobacillus ferrooxidans were both altered when the two colloid particles were mixed prior to the actual electrokinetic measurement. The need for more basic information regarding all aspects of the microbial-dependent solubilization of minerals is evident.

Jan 1, 1993

By Peter H. Grimley

It is important to realize that lending institutions have a very different risk-profile from that of an equity investor. For bank financing, a feasibility study must address the concerns of the lender and these can be summarized under the four 'PI Is: Project, Performance, Product and People. Generally, feasibility studies focus on the measurable project risks associated with a new venture, but frequently insufficient emphasis is placed on key risk areas such as ore grade and metallurgical recovery. Before accepting full or even partial non-recourse risk, financial institutions will demand evidence that the project was constructed according to specifications and within budget and that its Performance within agreed limits has been demonstrated. Product risk should be discussed in detail in any feasibility study. For industrial minerals, penetration of the market can be critical to success and for commodities with volatile prices, the sensitivity of the cash flow to a range of prices should be carried out. Methods of reducing price risk such as long term contracts or, in the case of gold, forward selling should be carefully evaluated. The People risk is rarely discussed in feasibility studies, but can be a key element. Few projects turn out to be faithful copies of the study and the ability of the operator to identify

Jan 1, 1988

Traditional fine-grinding mills in mineral processing rely on the use of steel medium for particle size reduction. The IsaMill (a horizontal stirred mill with a 3, 000-L net chamber volume and a rated motor power of 1,120 kW) has successfully adopted a novel product-separator design, which has led to a major revision of medium use in fine grinding. The IsaMill separator has successfully operated with a wide variety of medium types, such as silica sands, river gravel, smelter slag, run-of-mine ore fractions and steel shots, with sizes ranging from 0.5 to 10 mm. Great flexibility in the IsaMill operations has been achieved for processing feed as coarse as 120 µm to a product as fine as 5 µm. This paper discusses the performance of two inert grinding media in the IsaMills that are used at Mount Isa Mines Ltd. for the processing of galena- and sphaleritebearing ores to below 10 µm. They are the copper reverberatory furnace slag (CRFS) and the heavy-medium plant rejects (HMPR). A methodology was also demonstrated for comparing the medium performance and for scaling up the IsaMills from a 1.5-L laboratory batch mill to a full-scale 3,000-L mill.

Jan 1, 2002

By M. Alnot, J. A. Mielczarski, J. J. Ehrhardt, J. M. Cases

The flotation behavior of minerals depends on the balance between hydrophobic and hydrophilic species present at the surface of the minerals. The direct characterization of the interfacial products formed by the interaction of water and an aqueous solution of amyl xanthate with chalcopyrite, tetrahedrite and tennantite (the two former contain antimony and arsenic) were carried out by X-ray Photoelectron Spectroscopy (XPS) and infrared (IR) reflection spectroscopy. The experimental data collected from in-situ (IR ATR) and ex-situ (XPS, IR External Reflection) measurements have let us determine the types of the adsorption products and to propose mechanisms of interaction between the aqueous solution of surfactant and surface of the investigated minerals. It is shown that two major processes take place at the mineral interfaces: (i) the interaction with water and oxygen resulting in the formation of the oxidation products which are mainly hydrophilic (but also a hydrophobic product was found), and (ii) the adsorption of xanthate producing different types of hydrophobic surface products. The results obtained show differences in the composition of the outermost atomic layers of the investigated minerals which obviously will produce differences in the flotation behavior of these minerals. This work forms a good fundamental basis for a better separation between copper minerals containing arsenic and antimony, and chalcopyrite.

Jan 1, 1995

By B. Andersen, P. Somasundaran

An accurate knowledge of the interactions among mineral particles and between such particles and dissolved and precipitated species is important in developing efficient separation processes. In this investigation, interactions relevant to dispersion and selective reagent adsorption (the two main prerequisites for selective flocculation) within Florida phosphatic clay Waste were studied. Initial studies with artificial slimes, consisting of pure clay and phosphate minerals, showed dispersion of artificial slimes to be relatively easy. The problems that were encountered during selective flocculation of the artificial slimes were due to unselective polyacrylic acid adsorption on clay, which was caused by the presence of multivalent calcium ions on the exchangeable cation positions on the clay surfaces. This problem could be solved by exchanging calcium for sodium, which reduces the interaction between the polymer and the clay surface. This procedure, however, was not successful for mineral mixtures. Natural slimes were found to be much more difficult to disperse. This was attributed to the presence of cementing materials such as humic substances and Al and Fe (hydr)oxide precipitates. Selective removal of these cementing materials resulted in good dispersion and partial separation. A further increase in the separation of natural slimes is most likely determined by the presence of calcium on the clay surfaces, as was found for the artificial mixtures.

Jan 1, 1994

By S. F. Hillis, J. E. Rourke, K. A. Szalay, O&apos

INTRODUCTION For the past 25 years, tunnel support requirements have frequently been determined, at least in North American practice, by classifying the rock according to the system proposed by Terzaghi (1), using one or more of the 8 Rock Conditions which he defined, the rock load then being selected within the range given for each Condition. However, there is a lack of published data comparing Terzaghi loads with actual measured rock loads, and it would appear that the degree of conservatism, or otherwise, of the Terzaghi approach is very often unknown. Excavation of 4 large diameter tunnels at the Tarbela Dam Project in Pakistan afforded an opportunity to compare Terzaghi and measured loads, through instrumentation of the steel ribs installed for temporary support, and by classification of the geology exposed during the tunnelling operations. In addition, the deformation of the rock surrounding the tunnels was monitored during excavation by means of borehole extensometers installed prior to the start of tunnelling. This paper describes the tunnel instrumentation and the results obtained therefrom, and relates these results to the Terzaghi load coefficients. It also discusses the effects of the methods of excavating the tunnels on the rock loads and rock deformations. PROJECT DESCRIPTION The Tarbela Dam Project is located on the Indus River in

Jan 1, 1974

By Barry Silverman

As a significant mineral supplier, consumer of primary fuels, and producer of wastes and emissions to air, water, and land, the domestic copper industry through its investment and operating decisions influences the nation's economy and the environment. In turn, the copper industries' decisions are influenced by various factors: government energy and environmental policies, economic conditions, and technological considerations. The authors have developed a framework for assessing in an integrated manner the impact of these factors on the future investment and operating decisions made by copper firms. Specifically, this model is designed to capture the technology forcing nature of regulatory constraints, the differential situation of individual copper deposits and plant locations, and the price of factor inputs and conditions in the nation's economy. The capability to do this has only become real because of the decision of the U.S. Bureau of Mines to create Mineral Availability system1 or MAS. This system contains detailed but confidential information about each mine and mill in each of 35 mineral industries." Without MAS or a similar information system, the utilization of the methodology we offer would be impractical, but with. MAS it offers a unique technique of dealing with environmental-resources policy questions.

Jan 1, 1979