Search Documents

By J. Chia, M. H. Kobler, J. Cheung, M. J. Robison

INTRODUCTION The Lake Merced Transport is being constructed as part of San Francisco's Clean Water Program. The Clean Water Program, which began in the early 1970's, is designed to control wet weather, storm sewage overflows into the Pacific Ocean and San Francisco Bay. To accomplish this goal, a system of large underground storage and transport facilities, pump stations, modernized treatment plants, and outfalls is being built. By 1991, eighty percent of the system had been completed and was in operation. One of the remaining projects for the Clean Water Program is the Lake Merced Transport. The Lake Merced Transport is located in the extreme southwestern portion of San Francisco, as shown in Figure 1, Project Location. The transport will convey dry weather flow from the existing Lake Merced Pump Station to the Westside Pump Station. During wet weather, the transport will fill with sewage and runoff, with a storage capacity of 36 million liters. The Lake Merced Transport was expected to be excavated entirely within the Colma Formation, an alluvial deposit consisting of weakly cemented sand. Once excavation of the access portal at the Sloat/Great Highway parking lot began, it became evident that a portion of the tunnel would be excavated through beach/dune sand. Based upon the expectations of the Geotechnical Design Summary Report (GDSR), encountering beach/

Jan 1, 1993

By Jean-François Bougard

It has already been said and written many times that the construction of tunnels in urban areas has proved more and more indispensable, if not vital. The subsequent development of tunnelling for 15 or 20 years has brought large and sometimes spectacular improvements in the fiel of execution methods. But, particularly in urban areas, the difficulties to be overcome have been and still remain very important. As a matter of fact, most of big cities, have been settled near rivers or lakes; therefore the geological nature of the subsoil is soft ground and the level of ground water is high. As a consequence, tunnelling is often faced with many well-known difficulties and dangers issued from decompression or loosening of the ground, sometimes accompanied by a lowering of the water table. This may compromise the safety of the excavation itself and of the workers, and also cause settlements which many severely damage nearby buildings or structures. This is the reason why it is always necessary to work out specially adapted methods and even to develop new ones. In most cases, each work is a particular one and has to be specifically studied since numerous data are to be taken into account, related not only to geology, cohesion and behaviour of the different layers concerned, ground water, the activity of it, but also to

Jan 1, 1979

By Gerrit V. R. Goodman, Edward F. Divers, Charles D. Taylor

Future mining systems will possess the ability to cut from crosscut to crosscut where advances could exceed 30.5 m (100ft). However, limitations arise when ventilating such mining systems. In deep advance mining, there will be no workers at the face to manually advance ventilation tubing or curtain. Additionally, traditional methods provide no means for maintaining face ventilation after the miner backs out. Problems such as these have suggested the need for innovative ventilation methods compatible with deep advance mining systems. The Bureau of Mines is currently considering a number of innovative ventilation schemes. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Previous testing in large metal-nonmetal mine entries showed that jet fans provided adequate face ventilation for deep advances in large headings. Current testing will determine the application of jet fans in ventilating smaller coal mine entries. Another approach considered compatible with deep advance mining will use either exhausting or blowing tubing that can be remotely extended from crosscut to crosscut. During the mining cycle, such a device would extend automatically as the miner sumps into the face. The Bureau of Mines is considering several different operating designs using this tubing.

Jan 1, 1991

By Bruce C. Schepens

The Balsam Meadow Hydroelectric Project is currently under construction in central California. TMCI Construction, Inc. was subcontracted to perform the shaft enlargement and lining required for the elevator, surge and power shafts. Involved in the initial work was slashing the elevator and surge shaft into a previously excavated borehole. The elevator shaft then required a reinforced concrete lining and structural steel installation. Throughout the course of construction, numerous design changes occurred, necessitating a lining in both the power and surge shafts. These changes caused TMCI to design two underground hoisting systems to install these additional linings. An analysis of the construction methods used is now given. Introduction The Balsam Meadow Project consists of an underground hydroelectric powerhouse designed to provide additional capacity and energy to the Southern California Edison system during critical peak demand periods, and has the capability for pumped storage operation. The project is located in the Sierra Nevada Mountains about 55 miles northeast of Fresno. The project will divert water presently flowing from Huntington Lake to Shaver Lake to power a single 200 megawatt turbine generator. The approach used to the shaft slashing was governed partially by the strict CAL-OSHA requirements, which became more stringent after the recent Helms' Creek accident. A scaled down sinking plant was used to minimize economic risk and to simplify the excavation and lining scheme.

Jan 1, 1987

By Richard V. Good, John B. Harvey, Lloyd S. Jones

INTRODUCTION The term "Rapid Underground Excavation" is generally associated with high speed tunnel advance with large volumes of excavation, and indeed this is the type of work for which most of the recent innovations in methods and new machinery have been developed. However, the term applies as well to any underground excavation process that results in an earlier project completion than would be expected with conventional methods, and hopefully with a decrease in total unit excavation cost. Often significant progress has been made during the primary stages of an underground construction project and then an inordinate amount of time and effort has been expended on small units of "miscellaneous" excavation which has delayed the overall project completion and escallated overall unit costs. Construction at the Nevada Test Site of the Atomic Energy Commission for underground testing frequently requires significant amounts of so called "miscellaneous mining" such as short access drifts, cross cuts, alcoves, niches and concrete keyways. Many of the keyways must be excavated without disturbing the rock beyond the excavation lines and construction scheduling often dictates that much of the work must be accomplished without disturbing sensitive electronic equipment already installed. In order to cut down on lengthy and costly delays required for the tedious manual excavation of much of this miscellaneous mining, a market search was made for suitable mechanical excavation equip-

Jan 1, 1997

By Mustafa Kumral

The study area is located in the Alpine-Himalayan zone in Turkey. Geologically, this is a very complicated region, and the rock units generally are divided into two groups as either allochthonous and autochthonous. Tectono-stratigraphically, the units are Paleozoic quartzite, black limestone, arkosic sandstone, interlaminated radiolarite and Triassic limestone, thick Jurassic limestone, detritic limestone with alternating Eocene Nummulites beds and cream-green marl, Miocene siltstone, and ophiolite. Trachyte, trachyandesite, feldspathoidal trachyandesite porphyry, tuff, and pumice formed by volcanism during the Plio-Quaternary also are present. Recent alluvium and slope detritus locally cover all the other rock units. A number of sulfur outcrops occur in the area. Among them are outcrops at Keciborlu, Yelliyatak Hill, Buyuk, and Kucuk Kukurt Dere. The most important sulfur deposits are found in volcanic tuff and siltstone-marl, and they include highly organic material. Sulfur may accumulate around recent gas diffusions and also as massive formations. The information about local geology and sulfur isotopes shows that the sulfur originated From the crust and probably comes from organic-rich Paleozoic and Triassic units. The sulfur did not move between Triassic and Pliocene time. However. Plio-Quaternary volcanism did cause movement of the sulfur, and this was followed by formation of the secondary sulfur due to post-tectonic thermal activities and the mixing of other surface waters.

Jan 1, 1999

By Marek Wilczewski, Kristine Uhlman, Darrel Sipe

With the end of active copper mining in 1983, the extensive underground mine workings and the Berkeley Pit, one of the largest open-pit mines in the United States, began to flood. Daily in- flow to the pit is about five million gallons per day, with the water level rising at a rate of 30 feet per year. To support the remedial investigation and feasibility study, a six-layer, three-dimensional MODFLOW-based ground water flow model was constructed to simulate the 9,100-acre site. The vertical domain of the model extended over 1,060 feet of elevation difference and consisted of a finite difference grid of 89 rows by 54 columns. All work was PC- based. Model boundaries were assigned to correspond to natural hydrologic features such as geologic contacts, faults, and surface water features. The fully calibrated model was approved by the State of Montana and the U.S. Environmental Protection Agency (EPA) for use in the site remediation. The computer model was used to determine ground water flow velocities and contaminant travel times within the alluvial sediments adjacent to the Berkeley Pit. The purpose of the model was to predict future alluvial ground water flow directions should acid- and heavy metal-laden flood waters filling the Berkeley Pit rise up and enter the Alluvial Aquifer.

Jan 1, 1996

By John M. Wootten

The development of new coal markets is -t upon the ability to utilize coal in an environmentally acceptable and economically viable fashion. Foremost in the concerns about coal utilization is the impact its combustion has on air pollution. Concerns over environmental issues, such as acid rain, are currently one of the major impediments to the development of new coal markets. The Department of Energy and the Synthetic Fuels Corporation are addressing certain aspects of the development of new technologies for the utilization of coal. However, at the present time, there is a void in the new technology development process. That void is the step from proof- of-concept to commercial demonstration. Congress has established the Clean Coal Technology Fund at a level of $750 million to fill this void. The Department of Energy, in a solicitation of interest, received over 175 proposals for commercial demonstrations of clean coal technologies. A review of these solicitations indicates that $1.2 billion worth of research could be accomplished with a federal cost sharing of $425 million or 35 percent of the total. Industry has indicated, through this response, its willingness to invest its limited funds on projects it feels have the greatest potential for the clean use of coal. What must now occur is that Congress must appropriate the monies from the fund to initiate the commercialization of these clean coal techno1ogies.

Jan 1, 1986

By Joseph W. Kupfner

It is a recognized fact that a good maintenance program is a pre-requisite for minimum delay costs and maximum availability of equipment. To develop such a program and to make it effective, one must establish detailed instructions pertaining to inspections, lubrication, servicing, and/or replacing of various parts. A schedule must also be established for these maintenance checks, whether they be weekly, monthly, or whatever period is essential for the equipment. The number of tasks to be performed becomes monumental, and the administration is beyond error-free human capacity. It is for this reason that the computer must be an essential element in any efficient and economical preventive maintenance program. The evolution of a computerized maintenance program began some 18 years ago in the Mining Division of USSteel. It started with a manual system of preparing cards containing preventive maintenance instructions that had to be performed on some regular basis. We were very quickly overtaken by the massive task of administration and distribution of instruction cards to the users. The task became insurmountable as more mines were added to the system, mines that were spread over a large geographic area. It also became evident that the ability to make changes in equipment assignments and in the "what to do" instructions would require more time than had been anticipated.

Jan 1, 1986

By Jerry M. Whiting, Samuel Frimpong

Superior ventures selection and the subsequent management of their development and production are crucial in the competitive environment of the upstream minerals and energy industry. An important element of this chain is the management of uncertainty and risk dynamics. In the world of faster and more complicated technological and environmental changes, international competition and commodity market dynamics, thorough and sophisticated valuation must be carried out to establish a venture's value and return on investment. Thus, managers and investors must use methods that respond to market dynamics, investment and feasibility study options and provide relevant information for strategic investment decisions. Conventional methods have no built-in procedures to help investors analyse these options. Modern financial methods based on the dynamic arbitrage theory overcome these and other limitations of conventional methods. In this study, dynamic arbitrage theory has been used to formulate 3D parabolic differential equations that govern the stochastic processes of a copper mining venture with ongoing feasibility studies. The alternate direction implicit algorithm is used to solve the numerical approximations of the differential equations and their boundary conditions. Phase dynamics of the venture have been analysed to provide investors the appropriate timing for strategic investment decisions. The study also shows the amount and value of appropriate feasibility studies required to maximize the value of the mining venture.

Jan 1, 1996

By Maurice Rey

The copper segregation process is designed to concentrate oxidized copper ores or mixed sulfide-oxide copper ores which are refractory to normal and cheaper mineral dressing or leaching processes. Such ores contain copper silicates or highly disseminated copper minerals in a gangue not entirely free from limestone or dolomite. Concentra¬tion by flotation is, under these circumstances, not possible and the acid-consuming constituents do not permit acid leaching. A high temperature treatment at 700-800°C, in the presence of a small amount of sodium chloride and of finely divided carbon, concentrates the copper into easily floated metal by a kind of reducing chloridizing roast. The sulfides, if present, are either oxidized in the heating stage and react like oxides or float with the metallic copper in the flotation step. The ores which have the aforementioned characteristics and which are high grade enough to pay for the treatment are scarce, so that the process has only a limited application. Theory of Copper Segregation Sodium chloride, reacting with water vapor and the acid gangue constituents, produces hydrogen chloride which reacts with the copper minerals. The copper is volatilized as cuprous chloride and immedi¬ately reduced on the coal particles by hydrogen emanating from the volatile matter of the coal and from the water-gas reaction. Hydrogen chloride is

Jan 1, 1985

By Balesh W. Konda, Andrew B. Cecala

Face ignitions occurring during longwall mining are increasing each year and are expected to continue to increase as deeper and gassier seams are mined. Effective methane monitoring strategies are needed to supplement techniques developed either to control the ignition sources or to dilute the gas to an acceptable concentration. Present monitoring strategies do not always detect dangerous concentrations as rapidly as they should. In a number of instances, dangerous concentrations have been observed at the shearer, but are diluted to acceptable levels when measured at the tailgate monitoring location. To effectively monitor and control methane concentrations, methane liberation and emission patterns must be identified. This need has led to a joint research effort between the Canada Centre for Mineral and Energy Technology and the United States Bureau of Mines. By combining the knowledge and experience of both organizations, the methane hazard facing underground longwall operations can be addressed more effectively. A comprehensive plan was developed to monitor methane levels throughout the panel and for an entire longwall mining cycle. In June-July 1986, a case study was performed at the Cape Breton Development Corporation's Lingan colliery in Sydney, Nova Scotia. This initial study was performed on two advancing longwall panels. Methane concentrations and flow patterns from this study are described in this report. A similar study is planned on a retreating longwall panel.

Jan 1, 1987

By Thomas Fliess, Klaus-Christof Ritter, John R. Sturgul

The optimum flow of materials through a smelter is an extremely important phase of the mining cycle. A typical copper smelter will have up to $US 1,000,000 per day of copper being processed. The motion of the overhead cranes in moving the ladles filled with copper matte and slag from furnace to furnace is prescribed but there can be numerous variables to consider. Some of these variables to the system can be: the speed of the overhead cranes, the number of cranes, the size of the ladles, the size of the furnaces, the number of furnaces and the sequence in loading the furnaces. A simulation model was constructed of a working smelter in the SW of the United States. The model has been used to study the effect of varying parameters of the system. The program runs as follows: an input menu appears on the PC screen and the user can navigate through it and change any of the data; the simulation takes place and the results of the simulation sent to a data file. Animation of the system then is shown on the screen in "cartoon" fashion. The software chosen for the simulation was GPSSI H (') and PROOF Professional (') for the animation. The model presented here is believed to be the first reported simulation and animation model for a complete, working smelter.

Jan 1, 1996

By Bruce S. Brown, Jeremy P. Haile

The construction of tailings facilities and heap leach pads for gold mining operations generally requires the installation of one or more impermeable liners beneath the structures to satisfy environmental regulations and prevent the leakage of gold bearing solutions. Liners are usually constructed using clay soils or synthetic membranes, such as high density polyethelene. Low permeability soil liners can be constructed from natural clays, well graded soils with only a small clay content, or sandy soils blended with a small quantity of imported clay such as bentonite or kaolinite. The permeability of such materials, prgperly pped with good quality control, generally lies in the range of 10- to 10- cm/s, and can be designed to meet minimum prescriptive standards set by regulatory agencies. Important benefits resulting from the use of clay liners include the slow rate of penetration of a saturated wetting front, the decrease in permeability of the liner as it consolidates under the applied load of tailings or ore, and attenuation of potential contaminants in the process solutions. Synthetic liners can be attributed a finite permeability as a result of minute perforations and seaming deficiencies, and possess none of the above properties. Synthetic liners are also, by their nature, relatively thin and even a small head build-up above the liner will result in a large hydraulic gradient across it.

Jan 1, 1988

By E. J. Beckman, R. M. Enick, C. Powell

Liquid carbon dioxide can be used as a replacement for organic solvents in the extraction of anionic platinum group metal complexes from an aqueous phase. However, because conventional extractant-metal complexes are not soluble in liquid carbon dioxide, this can be achieved only if highly carbon dioxide-soluble extractants are developed. For example, trioctylamine-gold chloride is not soluble in liquid carbon dioxide, although trioctylamine is CO2 soluble. The novel CO2-soluble extractants presented in this paper have a CO2-philic fluorinated tail to enhance solubility and a conventional amine head group for extraction of metals. Both the extractant and the extractant-metal complex are soluble at ambient temperature at pressures from 7 to 35 MPa. Efficiency factors as high as 2.23 have been measured using 1,1,2-trichlorotrifluoroethane (TCTFE), a low pressure screening liquid for carbon dioxide, indicating that these compounds will strongly bind the metal chloride. For example, 84% of Pt-chloride was extracted into TCTFE using a 3.5:1 ratio of a double¬tailed fluoroalkyl amine extractant: metal chloride. An 88% recovery of Pt-chloride into high-pressure liquid carbon dioxide was achieved using the same extractant at a 3.5:1 ratio. Therefore, it appears possible to replace organic solvents with liquid carbon dioxide during the extraction of platinum chlorides if highly carbon dioxide-soluble extractants agents are employed.

Jan 1, 2002

By John A. DesLauriers, Hans J. Broennimann

INTRODUCTION The early record of tunnel excavating machines in hard rock tunneling has not been one to particularly brag about. We have all heard the stories of major difficulties when trying to break hard rock with machines at promised advance rates of several times that of conventional drill and blast. Unfortunately, sometimes this has not happened. It has been through this trial of the past generations disappointments that today's TBM's have evolved to their present high level of performance in a wide range of ground conditions. Today's machines offer much increased reliability and durability. This translates into high availability to the tunnel contractor. Although there still are occasional disappointments being reported, the state of the art is that reliable and predictable machine excavation of rock now is both a reality and well founded expectation. The most recent editions of Atlas Copco's MINI/MIDI Fullfacer, we feel, make a strong contribution to the reliable performance of todays TBM's---especially in small-size rock tunnels. This report will, 1.) explain the equipment and effect of rock both on the cutting technique and machine performance; 2.) list advantages of the non-circular shape, during and after construction; 3.) list applications in civil and mining industries; 4.) discuss North American experiences, performance and costs; 5.) list advantages over drill and blast and; 6.) discuss briefly lease arrangements.

Jan 1, 1979

By Nick Barton, Harald Hansteen

The deformations resulting from excavation of very large openings are compared using two-dimensional F.E. continuum analyses and discontinuous physical models (20,000 discrete blocks). Both the joint orientations and the model horizontal stress levels were varied. Some models were dynamically loaded to simulate earthquakes (0.2-0.7 g). Model deformations were recorded using photogrammetry. The changes in deformation when increasing the simulated spans from 20 m to 50 m were of particular interest. High horizontal stress caused surface heave when joint orientations were favourable for arch stability. Joint orientations also determined whether the pillars between parallel openings were in a state of compression or tension. INTRODUCTION The engineering performance of large rock caverns has traditionally been learned from mining and hydro power projects, where the depth below surface is often many times greater than the span of the openings. Deformations measured in the walls and roofs of hydro power caverns generally range from about 5-50 mm, though there is a documented case where a wall moved in 126 mm (1), and another where the arch moved down 147 mm (2). The chief objectives of the present studies of large near-surface openings were threefold: (i) to provide deformation data to compare with monitored data from planned engineering projects involving large span near-surface excavations, e.g. underground sports complexes, civil defense shelters, nuclear power stations,

Jan 1, 1979

By David M. Mchaina, Michel Grenier, Stephen G. Hardcastle

An airborne dust survey was conducted at the Arthur W. White mine of Dickenson Mines Limited by CANMET/MRL and Dickenson Mines Limited Staff in April 1990 for the purpose of evaluating environmental conditions underground and in the surface mining plants. The survey was designed to measure respirable silica, total arsenic and lead concentrations at several workplaces. In addition, settled dust and rock samples were collected from workplaces and analysed for total arsenic content. More importantly, arsenic exposure data were needed to evaluate the impact of Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. A total of 165 area and personal air filter samples were collected during the study. Of these, 85, 67 and 13 samples were for arsenic, silica and lead respectively. Sampling aid analyses were performed according to the Ontario Ministry of Labour Regulations. More than 90% of the workplaces sampled for respirable silica, total arsenic and lead were below the Ontario Ministry of Labour Regulations; and 10% of the workplaces sampled for arsenic shaved concentrations above the Threshold Limit value (TLV) proposed in the Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. These results were used to identify occupations and/or workplaces where more sampling and control measures were required respirable silica, total arsenic and lead. This paper describes the results of the dust sampling program conducted at Dickenson Mines Limited.

Jan 1, 1991

By J. Harrison Daniel

Increasing mechanization of underground mining operations throughout the years has reduced the dependency on large, concentrated working forces. Fewer workers in scattered locations, coupled with the versatility of diesel equipment to load and haul personnel, supplies, and mineral ore, has made diesel equipment attractive in mine feasibility and design studies. The use of the mobile equipment along with higher production or "bulk" mining methods provides for more efficient mineral extraction systems. These systems are expected to become more widespread until long-term research provides a further evolution to more complete automation of underground mining. The U.S. Department of the Interior, Bureau of Mines, has been conducting research to reduce the health and safety hazards posed by increasing use of diesel equipment and the higher power ratings being proposed. The goal is to provide for safe and efficient use of the equipment. The National Institute for Occupational Safety and Health has recommended that diesel exhaust be regarded as a potential occupational carcinogen adding importance to the Bureau's research program. The paper describes advances in engine design, the use of diesels in mining operations, and significant health and safety research accomplishments of the Bureau of Mines. These accomplishments will help assure that diesel equipment remains an option for determining the most efficient system to mine an ore body.

Jan 1, 1989

By Kenneth L. Rubow, Virgil A. Marple, Ye Tao

Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective sampling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler. Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8µm while mineral dust is greater than 0.8 µm. One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the large nonrespirable particles while the inertial impactor stage, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles (<0.8 µm and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol.

Jan 1, 1991