Search Documents

By C. D. Elifrits, N. B. Aughenbaugh

Laboratory tests of samples of fine- grained, argellaceous rocks, commonly referred to as shales, have shown that various changes in their moisture content can be correlated with loss of strength. This reaction to a change of in situ conditions at abandoned mine sites when combined with the field relationships at locations where the predominant overburden material is fine-grained, argellaceous, and fractured provides a predictive tool for engineers dealing with subsidence problems. Such a tool should enable engineers to recognize areas that are prone to be affected by surface disturbing subsidence features.

Jan 1, 1987

By S. Meng, R. Jin, W. Hu

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II) -activated sphalerite exhibits a high floatability so that satisfactory separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by infrared (IR) spectra; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitution and polymerimtion of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1988

By E. J. Miller

The Ventilation Branch is engaged in a project to determine if low level carbon monoxide monitors used for early detection and warning of fire in a coal mine conveyor belt entry can provide protection equivalent to that of thermally actuated point type heat sensors commonly used for fire detection. A series of tests were conducted to determine the required operating parameters, such as sensor spacing and alarm levels of detected carbon monoxide to provide equivalency between' these methods of fire detection. This report summarizes the results of these tests.

Jan 1, 1980

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open-pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected, including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1998

By K. S. Eric Forssberg, Lennart Ryk

The paper discusses coal utilisation in Sweden. All hard coals have to be imported from other countries. Peat from domestic sources is used as a complement. Environmental legislation and taxation on fuel and emissions are severe. This situation affects the procurement, preparation, handling and use of coal. The paper presents: • R&D projects concerning deep cleaning of thermal coal. • Handling and treatment of coal used in PFBC boilers and for blast furnace injection • Dust prevention for coal and peat briquettes. Procurement of coal emphasising quality and environmental issues.

Jan 1, 1995

By Danqing Xu, A. W. Khair

This paper presents a laboratory simulation of regrinding and resulting dust generation. An Automated Rotary Coal Cutting Simulator (ARCCS) was modified to conduct regrinding experiment. In order to estimate the effects of coal properties and operating parameters on regrinding and dust generation, an orthogonal fractional factorial experimental design was implemented in regrinding experiment. Marple personal cascade impactors, Series 290, were used to measure dust concentration during experiment. Three types of coal seams, namely, Waynesburg, Pittsburgh, and Lower Kittanning, were used to represent different coal properties. Experimental results and complete parametric analysis were presented.

Jan 1, 1991

By Pradip

It is possible to beneficiate low-grade phosphate ore slimes containing predominantly siliceous gangue by a combined selective flocculation-flotation scheme using commercially available reagents. The presence of clays, in particular, montmorillonite and attapulgite, has a disastrous effect on the efficiency of separation. Suitable remedies to overcome this problem are not yet available. Intensive R&D efforts are required in the areas of the design and synthesis of specific reagents, the effect of particle size, and the design of appropriate process equipment to carry out flocculation and flotation of slimes.

Jan 1, 1989

By J. Mark Richardson

Modern mining operations are increasingly affected by complex economic factors. Broad and rapid fluctuations in metal prices, rising operating costs, socio-political trends and the inherent technical difficulties encountered in most operations, all can combine to quickly change once-profitable ventures into money-losing propositions. Accurate knowledge of metal inventories during all phases of an operation has become essential to wise management decision-making. This paper reviews key elements of metallurgical accounting: sampling theory, measurement technology and computerized data adjustment. Application of current technology to the reconciliation of a hypothetical operation is discussed.

Jan 1, 1991

By Sangwhui Cho

In comminution processes including crushing, grinding and pulverizing, the efficiency of the comminution system is very low. Since the early 1980s, research has been conducted to increase the efficiency of pulverizing mills. Additionally, the application of microprocessors and Personal Computers to process control have come into general use. Given appropriate models of the process and control algorithms, these systems can economically control comminution processes. The ring-roller type mineral pulverizer is known as an energy saving mill. In this study, a control strategy to increase the efficiency of this type mill is explained.

Jan 1, 1992

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using discrete system simulation. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution used in a random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing needed and provides verification of how representative the samples are.

Jan 1, 2002

By David Royston

Conventional straight-radial SAG mill pulp lifters suffer from incomplete discharge of the rock portion of the charge. The resulting backflow of undischarged rock limits pulp lifter performance and is the major source of wear in pulp lifters. Backflow is increased in pulp discharge cone systems where multiple channels converge towards the central diversion cone. This paper covers recent experience with pulp lifter and discharge cone design supported by a single particle motion model that illustrates the discharge and backflow characteristics of pulp lifters, including the impact of discharge cone configuration.

Jan 1, 2005

By Joe W. Siefke

The world-class Kramer sodium borate deposit is being developed by modern open pit operations near Boron, California. The deposit is a bedded, lenticular sedimentary sequence of borax and kernite crystals together with claystone. The borates dip south into a structural basin-bounding fault and were formed in the bottom muds of a permanent shallow lake. The lake was fed boron and sodium-rich solutions from a thermal spring source of volcanic origin. In addition to deposit geology, present day geotechnical concerns such as groundwater and slope stability will be discussed.

Jan 1, 1995

By P. R. A. Andrews, R. K. Collings

The beneficiation of barite has been the subject of many investigations at CANMET, thus reflecting barite's importance as an industrial mineral. Fifty-one studies relating to various aspects of beneficiation were conducted between 1920 and 1986, and a review of some of the more important studies is presented. The information, including mineralogy, beneficiation methods and results, flotation parameters, and reagent concentration data, is presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of barite ores from a variety of origins.

Jan 1, 1990

By D. R. Zhu, H. S. Chiang, Y. M. Jiang, S. S. Peng

Two types of underground tests on three types of shield supports, 2-leg, 4-leg, and chock shield, were con- ducted to measure the horizontal movement of the canopy against the immediate roof. In no friction tests, steel rollers were placed between roof and canopy top, while in friction tests normal direct contact was used. Results indicate that the canopy for 2-leg shields always moves forward during setting, whereas there was no forward movement for 4-leg or chock shields. Based on the test results, a model for active horizontal force was proposed.

Jan 1, 1990

By Eleanore L. Nestlerode, James R. Guilinger

In April. 1990 Addwest Minerals acquired the Phillips Ranch sulfur property. The sulfur deposit, hosted by the Permian Castile anhydrite, occurs as two distinct elongate. parallel orebodies within a series of northeast-trending grabens. After completing a positive feasibility study, based, in part. on successful drilling programs by Addwest Minerals and previous operators, the decision was made to place the property into production. Utilizing an existing on-site kasch plant, plus significant portions of the recently purchased Texasgulf Comanche Creek Frasch plant. Addwest is currently constructing an 800 long ton per day Frasch mining facility.

Jan 1, 1992

By N. R. Paterson, D. A. MacFadyen

A late-1980 airborne EM/magnetic method test over the State Line kimberlite area of Colorado-Wyoming shows weak but recognizable anomalous responses to the known pipes. The magnetic survey indicates the presence of several shallow subsurface bodies adjacent to the known kimberlites, which are interpreted as possible blind diatremes. The survey data, in profile and contoured map form, has been correlated with geological map information available at the time. It can serve as the basis for reexamining kimberlite distribution in the area, taking into account geological findings during the recent work on known bodies.

Jan 1, 1987

By Robert F. Conley

This paper describes attrition milling as exemplified in rotary and vibratory mills for ultrafine grin¬ding application Without attempting to narrate the differences between various devices, generalized differences between the broad categories of rotary and vibratory milling are presented and compared with the ball mill Applications of these mills for coal, limestone, kaolin, mica, talc and iron oxides are described giving specific differences of the mineral properties that affect their behavior in the grinding mills Where applicable, specific recommendations are provided for ultrafine grinding of various industrial minerals

Jan 1, 1983

By J. W. Merks

Spreadsheet software is an effective tool for simulating dynamic stochastic systems such as mineral processing plants. The two-product formula is used to show how to set up a Monte Carlo simulation in a spreadsheet template and how to calculate variances of dependent variables. The key to a reliable and realistic simulation model is to obtain unbiased estimates for all independent variables and variances in the set that defines the stochastic system. Monte Carlo simulation is also a powerful tool for optimizing sampling procedures, for applying sensitivity analysis and for designing and evaluating experiments.

Jan 1, 2000

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1997

INTRODUCTION Automatic controls are devices that assist operators by performing routine tasks faster and better than they could alone. Great strides have keen taken in the development of new processes and bigger machines to improve productivity, but these developments created the need for increased protection of machinery and labor. The new production-line techniques, or continuous processes developed, resulted in routine and, frequently, demoralizing jobs. The human race is not constituted mentally to perform routine operations. Devices were needed also to gather information automatically and perform routine functions. High-capacity plants incorporating large equipment

Jan 1, 1985