Search Documents

By D. D. Murphy

The Bureau of Mines has studied the mechanism of shear-flocculation of silica with stearic acid. At pH 6 and 12, shear-flocculation of silica was not observed with up to 10-4M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations 10-4 M (5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labelled with a doxyl group. The presence of the spin-labelling group did not greatly affect the shear-flocculation properties of stearic acid. Adsorption of labelled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicate the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-414 (5 lb/st). The results are discussed in terms of a possible mechanism for shear-flocculation.

Jan 1, 1993

By Y. J. Wang

The definitions of system pressure loss (mine head) and system resistance, which are traditionally associated with single-fan net- works, are applied to multiple-fan ventilation networks. The system characteristics -- relations among air power, pressure loss, air quantity and resistance -- are analyzed by introducing the concept of subsystems. These subsystems are associated with the fans located in a cutset of the network. For a multiple-fan network, the resistances for the subsystems and total system are dependent on the quantity ratios of the subsystems. In general the pressure loss of a subsystem or a total system does not vary as the square of the corresponding air quantity. If the quantity ratios of subsystems are all held constant, then the resistances become constant and the pressure losses are predictable from the quantities employing the "square law." The system resistance has a minimum value under the natural- splitting flow pattern. Being independent of the value of system quantity, the minimum system resistance provides a basis for comparing the different networks.

Jan 1, 1983

By Drew Hobert, John Nielson, Erich Dohm

Metallurgical coal is an essential component for the blast furnace-basic oxygen furnace (BF-BOF) steelmaking process, which accounts for roughly 70% of total global steel production. To meet the growing demand for metallurgical coal, Arch Resources identified the potential to recover low- ash coal from ultra-fines discarded prior to the deslime flotation circuit across their portfolio of operations. Historically, many flotation circuits were designed to discard this ultra-fine coal due to high clay content and technological barriers to cost-effectively upgrade and dewater the coal to a saleable product. Recent advancements in high-intensity flotation technology, including the Eriez StackCell, have enabled coal producers to recover ultra-fine coal while minimizing capital and operating costs. In July 2023, Arch Resources commissioned the first full-scale ultra-fines recovery circuit utilizing StackCell high-intensity flotation technology at the Leer Mining Complex. This paper reviews the approach utilized to develop the flotation process design, learnings from the commissioning and ramp-up period, and performance data through the first year of operation.

Feb 1, 2025

By Ian Farrell, Josh Stowe, Eric Wingeard

Tailings transport system design is generally based on identifying the minimum and maximum process boundary conditions for pump selection and pipeline sizing. The approach is robust and well-proven. However, the approach has the potential to skew selections to operating scenarios that have a very low likelihood of occurring, such as the combination of high solids throughput and low tailings solids concentration. The approach can result in a tailings transport system design that is overly conservative. A probabilistic method-based approach captures the independent variability of design inputs and the combined likelihood of outcomes. This approach identifies the process conditions that have the highest likelihood of occurrence and are most applicable to equipment and pipeline selections. An outline of a probabilistic-based approach to tailings transport system design and the resulting selections is provided in this article. The probabilistic-based system design is compared to the outcomes from the traditional approach. The benefits and challenges to this approach are discussed and recommendations for utilizing this approach for tailings transport system design are provided.

Mar 31, 2021

By T. S. Golosinski

Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost, and significantly influence dragline productive time. Both work in very difficult conditions and wear out rapidly. As a result frequent rope changes are required at a substantial cost and time loss to the operation. Although performance of rigging has a profound impact on dragline performance, there are no industry-wide standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The life of drag and hoist ropes depends on: (1) rope construction, which should closely match requirements of the specific application, (2) correct definition and application of the rope discard criteria, so that full advantage of the rope can be taken without endangering safety of operation, and (3) rope operating conditions and its maintenance. The study presented in this paper was intended to address the above points, based on a survey and assessment of the present industry practice.

Jan 1, 1993

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner?s cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutterhead, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head?s effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner generally improved air quality at both sampling locations to varying degrees in some, but not all, mines when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By Timothy G. Shuttleworth

In the late1970s, mineral processing plants producing copper sulfide concentrates and oxide leaching feedstocks went online with operating tonnages that exceeded traditional installations. This created a need for larger capacity belt conveyors and apron feeders. Apron feeders are slow moving, heavily loaded conveyors that feed a deep bed of ore from a bulk holding location (a bunker) as a controlled stream, often into a large capacity crusher. Apron feeders use sprockets and caterpillars, while belt feeders use rubber belts with motorized head pulleys to convey the material. The damaging of belts and clogging of transfer points from tramp iron required larger magnetic separators and the removal of tramp metal cannot prevent these serious problems. Corrective action at this location is important for two reasons: Removing tramp iron early in the ore stream protects downstream equipment from potential costly damage. Installing apron feeder magnets before the primary large capacity crusher means that secondary and tertiary crushing steps (made up of multiple parallel units) operate more efficiently, since tramp metal is removed at the onset.

Jan 1, 2011

By S. Sener

In this investigation, the changes in the grindability of both ulexite and colemanite related with the different structural modifications created by the heat treatment were examined with respect to work index (Wi). The effects of the heat treatment temperature and time on grindability index were also investigated. It was observed that, heat treatment significantly affected on the grindability of ulexite. The work index of original ulexite was found 7.11 kWh/shton and decreased to 3.5 kWh/shton level within 200-480°C for 60 minutes. On the other hand, the work index of original colemanite was found as 6.48 kWh/shton and no appreciable change was observed when heated up to 320°C. Thermally assisted comminution can be used to improve the grindability characteristics of ulexite. Besides, the different behaviour of ulexite and colemanite under heat treatment can be used for their separation. The artificial mixture of ulexite and colemanite could be separated with over 90% recovery by utilizing their different grindability characteristics by thermal treatment, semi-autogeneous grinding and screening.

Jan 1, 1999

By James R. Walsh

While flue gas scrubbing with alkaline solutions is one of the oldest methods of removing SO2 from flue gas, a satisfactory scrubbing system for this application, which is both technically and economically viable, has yet to be developed. Interest in alkaline scrubbing has continued because of its basic simplicity and comparatively low capital cost. Drawbacks of alkaline scrubbing are the tendency for accumulation of solids to plug the system, scaling, corrosion and erosion problems and the need to dispose of large quantities of waste. Discussed are instrumentation loop applications to a 90,000 cfm alkali scrubbing test facility, the process problems the instrumentation engineer faces in. selection of equipment, the performance of the instruments selected and the problems encountered during start-up. The Test Facility incorporates centralized electronic process control with a digital data acquisition system provided to log process variables and print off normal (alarm) conditions. Flue gas SO2 content is measured by ultra-violet analyzers and analysis of the total gas stream is by gas chromatographs.

Jan 1, 1973

By M. Yekeler

The critical surface tension of wetting values (Ye) of realgar (AsS), talc [Mg3si401o (OH) 2]' stibnite (Sb2S3), and sulfur (S) were determined by flotation in the absence of conventional flotation collectors as 38.7, 38.0, 35.5, and 30.0 dyne/cm, respectively. The surface tensions of flotation media were arranged by methanol. Separation of binary mixtures of these minerals was performed exploiting their Ye differences-which form the basis of the "ganuna flotation process". One step flotation test showed that sulfur floats preferentially from its mixtures with realgar and stibnite at recoveries of 73.6 and 70.7 % and grades of 81.7 and 91.2 %, respectively. The separation of stibnite from realgar gave a recovery of 4.1 % and a grade of 41.2 % for stibnite, indicate that a minimal Ye difference of 3.6±0.2 dyne/cm is essential for such separation when conventional flotation reagents are not used. This paper presents data and describes the approach employed in these separations.

Jan 1, 1994

By Douglas H. Bolton

In recent years, equipment manufacturers have been busy developing remote control systems to catch up with the sophistication and efficiency of continuous miners. Now the tables are turned, and manufacturers are undertaking the new challenge of upgrading, refining and equipping continuous miners to take full advantage of the capabilities made possible by modern, successful remote control systems. Because the operator can safely advance the miner farther without pulling out for roof bolting, continuous miners now need to be equipped with means of complying with correct face ventilation, dust suppression, methane detection, diffusion and improved lighting. Some of the exciting possibilities being developed to catch up with remote control include feedback controls using laser beams as datum points, coal sensing devices with feedback signals to show the operator what the machine is doing, show where it is relative to the coal seam, how hard it is working, and more sophisticated use of cyclic control. Mining machinery manufacturers have accepted the new challenges, and faster, safer mining procedures are already in sight.

Jan 1, 1975

By J. Hahn

Modern high-performance disc filters such as the BoVac Disc Filter have set new standards in applications where large capacities of solids, liquids and air have to be managed through the filters. These disc filters have an enormous hydraulic capacity. For applications in mineral processing - with a special focus on tailings – which typically have high solids throughputs but low filtrate and air flows, this capacity can be used to expand the filtration area while maintaining the benefits of very good cake discharge even with thin cakes (4-5 mm) and a high filter speed. Research work over the last century has proven that increasing the filter area should be achieved by increasing the disc diameter. Because adding more discs leads to big problems with the cake discharge. However, as the disc diameter increases, the filter segments become longer and heavier. A suitable compromise was therefore found by doing both. The result is the first vacuum disc filter that offers significantly more than 300 m² of filtration area, but has no more than 6 discs.

Feb 1, 2023

By NEHA PANDEY, V.K. REDDY KALLAM, SUNIL KUMAR TRIPATHY, ARIJIT BISWAS

This work discusses the sulfur dioxide (SO2) leaching of low-grade ferruginous manganese ores to selectively recover manganese (Mn) as manganese sulfate (MnSO4), followed by electrowinning of the purified MnSO4 to produce electrolytic manganese dioxide (EMD). The effects of the leaching process parameters on Mn recovery were studied, and the leaching duration and SO2 flow rate were found to have significant effects. Under the optimum conditions derived for grade 1 ore (with total Mn content of approximately 17.16 percent), the specific SO2 requirement (SSR) — that is, the SO2 flow rate per gram of Mn in the leach slurry — was calculated to be 0.014 L/min. At the SO2 flow rate calculated using SSR for grade 2 ore (with total Mn content of approximately 26.29 percent), a Mn recovery rate of 94 percent was realized. Electrowinning of the purified MnSO4 generated after leaching resulted in EMD with 88.01 percent purity and a γ structure.

Sep 1, 2022

By Z. T. Bieniawski

The efficient and safe design of room-and-pillar coal mines still remains as one of the pressing problems facing the mining industry in the United States. Although much research has been directed to stability of mine roofs and coal pillars, no generally-accepted design method has been formulated. This paper presents a concise procedure for an improved design of room-and-pillar coal mines. Developed as a result of a three-year research effort, the methodology includes essentially three aspects: (i) determination of stable roof spans; (ii) determination of the strength of coal pillars; and (iii) determination of safety factors for room-and pillar coal mining in the United States. It is shown that the presented approach will lead to a greater recovery of coal by a more economical, yet safe, mining operation. Design charts and tables are presented and a step-by-step design procedure for practical mining engineers is explained. Several examples are included demonstrating the use of the proposed design procedure for room-and-pillar coal mines.

Jan 1, 1983

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Red mud has been reported as a potential resource for lithium. To investigate the leaching behavior of lithium, a lithium-rich red mud was neutralized with hydrochloric or oxalic acid and then leached with acetic acid. When red mud was neutralized using dilute hydrochloric acid, about 58 to 60 percent of lithium was leached with 25 percent acetic acid at 95 °C for 60 min, while more than 95 percent of sodium and 85 percent of calcium were dissolved in the leachate solution. When oxalic acid was used to neutralize red mud prior to acetic acid leaching, lower lithium leaching efficiencies of about 42 to 47 percent were observed. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the same conditions. In this study, 25 percent (v/v) of acetic acid at 85 °C for 60 min was demonstrated to be the optimum conditions for lithium extraction from oxalic acid-neutralized red mud using acetic acid. The results are useful and of interest for lithium recovery and purification from red mud.

By K. F. Unrug

An overview of the history of mining technology, both past and present, shows that some of the new concepts being successfully applied have changed the reserve categorization and are having an overall impact on production. Past coal mining operations in the eastern coal fields, and especially in Appalachia, extensively utilized stripping with the predominately applied contour method. As a result, vast mountainous areas have abandoned benches left behind by past mining operations. While thicker seams previously stripped were usually mined by underground or mountain top removal methods, thin seams beyond technical or economical limits were left intact after contour mining had reached the ultimate height of the wall. These thin seams quite often contain high BTU, low ash and sulfur coal that makes them attractive for a secondary recovery due to the market requirements. Secondary highwall recovery has obvious potential and is economically attractive; however, with the present state of industrial experience and lack of analysis of site data, a trial and error approach is used by operators.

Jan 1, 1983

By William W. Leathen

Acid mine drainage became a reality through the exposure of the first bituminous coal seam, either by man or by nature. At first the small amount of acid formed was quickly and efficiently neutralized by basic rock strata and by neutral or alkaline water. As soon as extensive mining operations overtaxed nature's own defensive measures, acid mine drainage became a problem of concern to government and the coal industry. It was the purpose of the studies conducted at Mellon Institute to accumulate knowledge, both applied and fundamental, relating to the formation and disposal of acid mine effluents. It was during this program that the microbiology of acid mine water was studied. Most bituminous coal mine effluents are highly acidic and contain, along with other ions, high concentrations of ferrous iron. The acid is sulfuric, and. the iron is present as the sulfate; both are the oxidation products of iron sulfides (FeS2) which are present in the form of pyrites, marcasites, or other sulfuritic minerals. The oxidation occurs, in the absence of moisture, according to the following reaction: [ ]

Jan 1, 1959

By James W. White

From Modular's first truck-dispatching system for Phelps Dodge Corporation in 1979 to today's alliance between Modular and Komatsu, Ltd., innovation has been Modular's main product. This paper describes the growth of a mining products supplier and the philosophy and decisions behind that growth.

Jan 1, 1998

By Harry Sutcliffe, Francis M. Keville

The paper describes the, impact of the geotechnical exploration program on the line and grade of the tunnels and the shaft configuration on the Red Line Extension N.W. in Cambridge and Somerville, Massachusetts, and comments on several aspects of the implementation of the project.

Jan 1, 1983

By G. E. Burrer, D. Malhotra, T. E. Irwin, S. Johnson

Climax byproduct-plant tailing assayed 0.019% WO3. Pilot-plant and laboratory tests were performed to investigate the possibility of recovering additional tungsten values from the byproduct-plant tailing. The methodology used in the study and the results of this investigation are discussed.

Jan 1, 1987