Search Documents

By K. Thirumalai

The Bureau of Mines has developed and tested a new concept of combining thermal and hydraulic energy processes for hard rock cutting. The study shows that this novel combination method overcomes the fragmentation limitations of the thermal process in nonspalling rocks and the cuttability limitations of the hydraulic process in high-strength rocks. The method effectively cuts hard rocks at moderate hydraulic pressures (below 30,000 psi). Theoretical predictions of the rock damage process are made and are correlated with experimental results obtained by using both single pulse and continuous water jet hydraulic systems. Traversing point heating and line heating techniques were used for heating rocks preceding the continuous jet impingement. Heating induces structural weakness of the rock material and assists fragmentation by the water jet impingement. The thermohydraulic process is effective if the significant depth of heat penetration induced by the surface heating exceeds the cutting depth produced by the jet impingement. Hydraulic specific fragmentation energy values reduce by about an order of magnitude using the combination technique. The process efficiency and the rate of themohydraulic hard rock cutting increases significantly by increasing the intensity and duration of heating.

Jan 1, 1973

By Thornton L. Neathery

A small area in the Alabama Piedmont was studied to determine if metallic enrichment was associated with local magnetic anomalies. Cores from two holes in these magnetic anomalous areas have sulfide (pyrite, pyrrhotite, chalcopyrite) film on slicken-side and fracture surfaces. Two hundred and fifty soil samples were collected from the top of the "B" horizon on 1, 000 foot centers over the general trend of magnetic anomalies. Soil samples were leached with a 1:2. 7 mixture of HF and H2SO4 and the dilute filtrate analyzed for Cu, Pb, Zn, Ni, Co, Cr, Mo, and Cd, using atomic absorption methods. Concentration-value maps were prepared for each element. Small areas of anomalous concentrations were defined for Cu, Pb, Zn, Mo, and Ni. Some of these areas generally coincides with magnetic anomalies. Concentration values (ppm) range from: Cu 165.0 - 0. 5; Pb 265. 0 - 0.0; Zn 1386.0 - 43. 0; Ni 187.0 - 10.0; Co 207.0 - 6. 5; Cr 117.5 - 2.0; Mo 95.0 - 0.0; and Cd 32. 5 - 2.0. Studies of other magnetic anomalies appear warranted.

Jan 1, 1972

By D. A. Rice

As part of a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input-from the phosphate industry, the conversion of phosphor-gypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: 1) thermal treatment to volatilize sulfur, and 2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked-cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1988

By B. Jones, W. Zhang, Q. Li

Rare earth elements (REEs) are critical materials to the United States due to the imbalance between their supply and demand. Considerable research and development efforts have been devoted on REE recovery from coal refuse using inorganic acids as lixiviants, however, the cost of inorganic acids is normally high, and the environmental friendliness is low. As alternatives to inorganic acids, organic acids of small molecules such as lactic acid and succinic acid have been used as efficient and green lixiviants for metal extraction. In addition to the supply risk of REEs, food waste generation and disposal is another emerging and critical issue since nearly one-third of the edible food is lost or wasted each year. In this research, organic acids were microbially converted from food waste and used as lixiviants to leach REEs from density fractions of an Illinois Basin coal. Experimental results indicate that REE recovery increases of up to 15 absolute percentage points were obtained using organic acids relative to inorganic acids. The conversion of food waste into value-added, renewable, and environment-friendly chemicals promotes the economic viability of REE recovery from coal refuse.

Mar 2, 2022

By Victor J. Scaravilli, C. Richard Linamen

This paper presents a case history of Southwest Interceptor Contract No. 1, Cleveland, Ohio. It details some of the problems and solutions of handling and erecting precast concrete segments in a small bore soft ground tunnel. It also reviews how specific interpretations of contract requirements and contract administration effect production, performance and productivity.

Jan 1, 1987

By D. C. Panigrahi

The paper presents the application of Object Oriented Programming approach for the development of a network simulation model based on nodal pressure method using linearised flow equations. The convergence and computational efficiency of the algorithm have been investigated. Finally the paper re- ports the validation of this algorithm in actual field conditions.

Jan 1, 1996

By M. W. Brandt

In the November 1957 issue of "Chemical Process Engineering," a British publications, there appeared an article entitled "Correct Selection of Drying Equipment." The author wrote as follows "Whether batch drying or continuous drying' methods are applied, the basis of efficient drying is heat distribution, control of rate of heat input, and heat transference from heating medium to the particles of the material to be dried." The author continues: "Because the efficiency of direct dryers, such as hot air or hot gas dryers, increases with rising inlet temperature of the drying air or gas when exhaust temperature remains fixed, the highest practical drying temperature should be used. Exhaust air should leave the dryer at the lowest possible temperature, but as fully saturated with moisture as possible." It is certainly conceivable that the author of this article by outlining the basic requirements for efficient drying methods has unwittingly given the reasons why fluidized drying is rapidly being adopted for so many industrail applications, including the dryingof fine coal. An examination in greater detail of the individual basic requirements for efficient drying as outlined by the author is perhaps the most logical starting point.

Jan 1, 1958

By Ingvar Janelid

During recent years, numerous articles have been published regarding theories and practical applications of sublevel caving. The reason is the great interest this method has created through its possibilities of standardizing and mechanizing operations and equipment. Other advantages are that the method can be adapted to orebodies of different shape, size, strength etc., and especially that working conditions can be made safe and relatively comfortable since all work is carried out in drifts. As is well known, the disadvantages or sublevel caving are that ore recovery hardly exceeds 85-90 % if waste rock dilution is to be kept below 20-30 %. Therefore, the main research and development work has been concentrated on parameters which can affect and reduce these disadvantages. This paper deals only with principles and problems which apply to large, massive orebodies. The problems with narrow, vertical or inclined orebodies are so different that they require a special handling. In my opinion, the intense research and development work during recent years, combined with practical experience, has given enough knowledge of the influence of different parameters, so that normal sublevel caving can be efficiently planned.

Jan 1, 1975

Iron removal using biologically produced organic acids was investigated as a treatment option for the production of refractory grade bauxite. A leaching solution containing 98mM oxalic and 67mM citric acid was prepared from a sucrose medium using for fermentation the fungus Aspergillus niger. The leaching capacity of the metabolic product was tested on a bauxite sample containing 16-19% iron (as Fe2O3). Aerobic and anaerobic leaching tests were carried out at pH 3, 50°C and in the absence of light. Results indicated that more than 80% of total Fe can be removed from the ore, when the sample is finely ground and applying a two stage treatment. The presence of oxygen was seen to affect adversely the kinetics of the process, suggesting that leaching follows a reductive mechanism. Experiments that were carried out with different particle size fractions indicated that for obtaining efficient removal of iron particles should be finer than 0.63mm. Reduction of the operating temperature from 50 to 30°C caused a decrease in the rate of iron removal by more than 10 times.

Jan 1, 2006

By Cuong V. Trang, Christopher A. Fleming

There has been greatly renewed interest throughout the gold mining industry over the last few years in cyanide recovery from gold and silver plant tailings. This interest has been spmred by two factors. Firstly, the increasing cost of destroying cyanide to levels that meet more and more stringent regulations for tailings impoundment or discharge to the environment. Secondly, many gold ore bodies suffer high cyanide consumption costs as a result of the presence of base metals (principally copper) that react with and consume cyanide during the gold leach. In most cases, the cost of recovering and recycling this cyanide from the tailings is signif­icantly lower than the cost of purchasing new cyanide. When this cost benefit is added to the lower costs of tailings detoxification, a compelling case can frequently be made for cyanide recove1y. A number of processes for recovering cyanide from gold plant barren solutions or pulps have been developed. Most of the processes require that the recoverable cyanide is first converted to the highly toxic hydrocyanic acid gas (HCN) and fears surrounding the handling of this compound have probably presented the great­est impediment to implementation of these processes.

Jan 1, 1998

By Karl O. Toppel, Jim Flaherty

The desire to minimize gaseous effluent in smelting and maximize gold yields from refractory ore are driving the nonferrous and gold refining industries to demand more and more oxygen. This, coupled with an increasingly competitive marketplace, forces the investigation of alternate methods of oxygen supply. Current progress in both the non-cryogenic and cryogenic fields is making the use of low-purity oxygen much more attractive. The benefits of on-site production are now available to most oxygen users. Historically, these on-site advantages could only be achieved by relatively large plants using high-purity cryogenic technology. The evolution of low-purity cryogenic and non­cryogenic oxygen production has added a new method of delivering on-site production. Specifically, the advent of oxygen Vacuum Swing Adsorption (VSA) technology has brought these benefits to smaller-volume customers by cost-effectively supplying oxygen requirements as low as 20 tons per day, (tpd). Low-purity cryogenic plants have also made an impact on the market, yielding cost reductions for larger-volume customers with oygen requirements greater than 70 tpd. This paper reviews the advantages and disadvantages of current supply methods for users having varying volume, purity and other requirements.

Jan 1, 1993

The development of a successful restoration strategy for any drastically disturbed site is dependent upon a thorough understanding of the chemical properties of the spoils or mining wastes that need to be stabilized. The majority of revegetation research in the USA has been conducted on coal mining spoils and coal preparation wastes, and this paper will focus on these two materials and their modification for plant growth and water quality protection. Potential acidity derived from the oxidation of pyritic (FeS2) materials is the most important chemical factor that must be estimated and managed, but physical properties such as severe compaction or excessively low water holding capacity are also very limiting. Conventional soil fertility tests are very difficult to interpret for mine soils because of their tendency to extract elements from fresh, unweathered surfaces that are soluble in the extract, but not plant-available. A wide array of waste products such as sewage sludge biosolids and coal fly ash are readily available for use as mine soil amendments, but their utilization must be carefully matched against the needs of the post-mining plant community and their potential water quality impacts.

Jan 1, 2002

By Andrzej Wala, Waclaw Dziurzynski, Janusz Tracz

Recent advancements in computer hardware have led to the development of new ventilation planning software for PC's. These programs now can be run more quickly and can display their outputs with graphical techniques. Only a few of the existing programs have the capability to display the output data graphically on plotters. Graphical presentation of ventilation simulation data is essential for quick and sure comparisons of alternative analyses. Recently a noticeable growth has occurred in the application of graphics for display and interpretation of the data that have been developed by simulation procedures. The process of mine ventilation network analyses used for planning and design can benefit from this development. The authors describe and present graphics-assisted software that has been developed to work with a mine ventilation simulation program. This software has some of the following features: - graphic editor on screen, - graphical display of output data on screen (EGA, VGA), - graphical display on plotter or printer, - scaling capability (desired part of the entire schematic can be displayed), and - such values as flow, pressure loss, gas concentration for branches, and pressure and elevation at junctions can be presented as labels.

Jan 1, 1991

By William Cowan, Robert Spencer, Lynn Carpenter

INTRODUCTION The Bureau of Reclamation is conducting a research program to investigate, develop, and test polymer-impregnated concrete tunnel support and lining systems for gravity flow, circular cross-section water conveyance tunnels. This system consists of segmented precast rings, backfilled with concrete. Polymer-impregnated concrete is conventional precast concrete which has been impregnated with a liquid monomer. The liquid monomer is subsequently converted to a polymer by thermal-catalytic or radiation methods. The polymer is a solid plastic which fills voids and microfractures within the concrete, resulting in greatly improved strength and modulus of elasticity and reduced permeability, which in turn increases the durability of the concrete. The immediate goals of the program are to develop techniques for the fabrication of precast concrete segments, test single segments to determine physical and mechanical properties, assemble the segments into a support and lining system, load and test the full-scale system, evaluate specific applications, and develop design criteria and construction procedures. NEED FOR THE TEST PROGRAM Modern rapid underground excavation technology emphasizes desirability of supporting and lining a tunnel closely behind the heading without reducing the excavation rate. Therefore,

Jan 1, 1997

By Hang Yang, Linneas W. Laage

A major concern of mine fires is the heat generated ventilation disturbances which can move products of combustion (POC) through unexpected passageways. Fire emergency planning requires simulation of the interaction of the fire and ventilation system to predict the state of the ventilation system and the subsequent distribution of temperatures and POC. Several computer models were developed by the U.S. Bureau of Mines (USBM) to perform this simulation. The most recent, MFIRE, simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influence such as varying outside temperatures, and internal influences such as fires. Extensive output allows quantitative analysis of the effects of the proposed alteration to the ventilation system. This paper describes recent USBM research to validate MFIRE's calculation of temperature distribution in an airway due to a mine fire, as temperatures are the most significant source of ventilation disturbances. Fire tests were conducted at the Waldo Mine near Magdalena, NM. From these experiments, temperature profiles were developed as functions of time and distance from the fire and compared with simulations from MFIRE.

Jan 1, 1995

By O. Ofor

Coal fines of less than 0.5 mm particle size, discarded as too fine for gravity separation, were subjected to flotation tests at varying pH and temperatures using modified dosages of kerosene as oil phase and methylisobutylketone (MIBK) as frother. Optimal coal recovery of over 74% was obtained using 200 kg kerosene and 4 kg MIBK per ton of coal fines at a pH of 9.7 and an ambient temperature of 26° C. The coal concentrate obtained under these optimal recovery conditions assayed 9.10% ash, 0.35% sulfur and 0.011% phosphorus, representing reductions in the ash, sulfur and phosphorus contents of approximately 75%, 43% and 8.3%, respectively. Its gross calorific value was 32.9 MJ/kg, its percentage of volatile matter measured 30.6 and the fixed carbon content was 66.3% (d.a.f). Caking tests showed the optimal concentrate has a standard welling number of 1 and is a Gray-King coke type C. These results show that the optimal flotation product could be utilized for such industrial purposes as steam raising or for processing in gasworks, but it would be unsuitable for metallurgical coke production.

Jan 1, 1993

By F. Chavan

1. Introduction The new Cleuson-Dixence development project in the Valais region of the Swiss Alps, involves the construction of a new link between the Grande-Dixence dam (still world recordholder with a height of 300 m) and a power house on the banks of the Rhone consisting of approximately 20 km tunnels and shafts, and involving a fall of about 1900 m. This 1200 MW project will replace an existing 900 MW structure built in the 1960s, no longer considered efficient. The new project comprises a head race drift about 15.8 km long, a surge tank, an inclined cascade shaft 4,2 km long, and an underground power station. The work for lots C and D (head race drift from Tortin to Tracouet, surge tank, six adits ans the complete inclined shaft) was awarded to our group (Prader, Locher, SELL, Losinger, Evéquoz, Dénériaz, Imboden and Bouygues). The geological conditions are: Lower part of the shaft (300 m) : sedimentary - sandstone and soft tertiary sandstone. Middle and upper part (2600 m) : metamorphic - upper and lower carboniferous, interrupted by triasic chipping. The horizontal section (7 km) consists of mica

Jan 1, 1995

By M. W. Ryan

The US Bureau of Mines investigated cold-cutting alternatives to oxyacetylene torch cutting of metal. The alternatives examined were a pneumatic circular saw with an abrasive cutting wheel, a handheld abrasive water-jet cutting tool, an ultrathermic-cutting system, hydraulic punches and cutters, and a pneumatic reciprocating hacksaw. Sparks generated with the pneumatic circular saw or ultrathermic-cutting system were not completely eliminated with the use of water sprays. The water sprays also reduced the cutting rate of the pneumatic circular saw by 70%. The safety and performance of a handheld abrasive water jet cutting system requires additional research. The hydraulic cutters and punches are readily available and do not introduce any hazards. However, they are not comparable in price to the oxyacetylene gas torch and many different attachments would be needed to replace the torch. The pneumatic reciprocating hacksaw, which did not produce any sparks, is an acceptable alternative in terms of cutting rates. However, the price of the saw and blades is not comparable to that of the oxyacetylene gas torch. The results of this study will further the advancement of safe, efficient alternatives to oxyacetylene gas torches, which will improve miner safety.

Jan 1, 1996

By S. K. Mishra, S. B. Kanungo

Because conventional (physical) methods of ore dressing are not suitable for reducing the phosphorus contents of high-phosphorous manganese ores from Andhra Pradesh (AP) and the adjoining area in southern Orissa, India, the adoption of chemical methods becomes imperative. An attempt was therefore made to reduce the phosphorus content of partially beneficiated manganese ores from AP by roasting with sodium carbonate and then leaching with hot water. However, due to the higher phosphorus contents of the manganese ores from Nishikhal mines in southern Orissa, and because of their apparent resistance to dephosphorization by roasting with Na2CO3 alone, a mixture of Na2CO3 and NaCl was found to be necessary to reduce the phosphorus content to below 0.15%. Free-energy calculations at 700°C and above indicated that Na2CO3 (or Na2O as the active component) is a more active reagent than NaCl. Various process parameters, such as the temperature and time of roasting, the amount of sodium carbonate and the temperature and time of leaching, were studied to arrive at the optimum conditions for dephosphorization.

Jan 1, 2000

By Toyohisa Fujita, Mitsuo Mamiya, W. Tai Yen, Hiroki Kogita

Green algae taken from an acidic mine drainage and blue-green algae taken from an alkaline hot spring stream were collected and tested for their ability to recover or remove dilute metal ions. Experimental results demonstrated that unwashed blue-green algae and washed green algae effectively adsorbed base metals ions and eluted them at pH 1. It was also found that washed and dried algae adsorbed precious metal ions more effectively than unwashed algae. For example, the washed and dried blue-green algae was capable of adsorbing 0.31 kg of gold per kg of algae. The gold from tetrachloroaurate solution which was adsorbed on washed blue- green algae was found to change to a metallic state following initial metal binding. In the case of a dilute gold complex solution leached with thiourea, only a small amount of gold could be captured by algae. Further experiments were conducted on components of the algae, such as alginic acid, agar, cellulose and chitin and mixtures of these components, in order to determine their contribution to metal adsorption characteristics. However, a mixture of these two components demonstrated both good adsorption and desorption characteristics indicating an interaction between the individual components.

Jan 1, 1995