Search Documents

By J. Kelleher, R. Saulters, K. H. McDaniel, L. Griswold

To improve underground safety and visibility during mining applications, the Waste Isolation Pilot Plant designed and built a dry-dust filtration unit. The unit works in conjunction with a Spendrup 1120-70 fan with ventilation tubing to filter the face exhaust air during mining operations. The closed- loop system is designed to filter 17 m3/s (36,000 cfm) and is intended to screen 10- µm (1,250 mesh) and larger particles at 90% efficiency. To accomplish this, the unit uses a combination of Dollinger Staynew Inertial Spin filters, cyclones and traditional mesh filter media.

Jan 1, 2002

By R. C. Guimareãs

Serrana's deposit contains three types of ore: oxidized, micaceous and silicate-carbonate. The results presented refer to characterization and fundamental studies performed on fractions resulting from the purification of five samples from the silicate-carbonate type collected in the mine. Each type was purified and submitted to mineralogical characterization, zeta potential determinations, and microflotation experiments. The samples, with exception of the barite, are mineralogically complex and the selectivity between apatite and gangue minerals is poor. Under the current state of art, it is impossible to feed the plant with the silicate-carbonate ore, unless it is blended with the standard oxidized ore.

Jan 1, 2002

By O. E. Etheridge Jr., R. A. Lowe, C. I. Basilio, J. M. Randolph, S. W. Sheppard

The low-shear viscosity of kaolin slurries is one of the principal characteristics that determine whether a clay can be utilized for paper and ceramic applications. In this work, the causes of high low-shear viscosity and methods for improving the rheological behavior of the slurries were investigated. The presence of fine-grained smectite impurities within the kaolin was shown to detrimentally affect the low-shear rheology of the slurries produced from these clays. It was also shown that mechanically working (i.e., pugging) a crude kaolin followed by desliming to remove these impurities can reduce the low-shear viscosity.

Jan 1, 2000

By G. A. Hazen, S. M. Sargand

This study monitored longwall mining subsidence profiles over three panels that were mined beneath state highways in southeastern Ohio. The average maximum subsidence was 1.07 m (3.5 ft). The average maximum compressive strain recorded was 0.008 mm/mm. Three predictive methods for the determination of displacements and strains were compared: the National Coal Board (NCB) graphical method, the profile method with empirical constants determined for southeastern Ohio, and a finite element excavation program. Excellent subsidence agreement was found with the profile method, and reasonable strain agreement was determined with the finite element program.

Jan 1, 1987

By R. L. Grayson

As a followup to a USBM-sponsored research project, the authors utilized the knowledge-base structure and system concepts from a Sun Sparcstation-based worker-scheduling system of the mine-management support system to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, including their availability and work priorities during a shift. The system can optimally allocate manpower on a work shift and can delineate supervisory training responsibilities. The various components of the software, including enhancements made to the original system, are described in detail.

Jan 1, 1997

By Terry A. Ring

Sand bed filters are used to remove large and small particles from liquid streams. The large particles are removed by the straining action of the filter bed and the small particles are removed by particle deposition on the surface of the bed particles. Particle deposition, while being essential for the filtering action of colloidal particles, is not the only process that occurs in the filter bed. Other processes that occur are (1) the substrate becomes filled with particles limiting further deposition, and (2) some deposited particles are resuspended. The sum total of all these processes determine the performance of a filter bed.

Jan 1, 1982

By P. Tsang, S. S. Peng

The stability of longwall chain pillars depends not only on the mechanical properties of the coal and surrounding rocks but also on geological and mining conditions. To evaluate the effects of each variable, orthogonal experimental design was employed in a significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of the Young's moduli of roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1996

By William J. Attwooll

The development of gold heap leach projects in the Cripple Creek, Colorado, mining district has required utilization of heap leach pad sites other than relatively level natural ground. This paper describes the construction of a heap leach pad adequate to accommodate 907,000 tonnes (1,000,000 st) of ore over the surface of a tailings pond constructed during previous milling activities at the site. Based on the design parameters and the observed behavior to date, it has been found feasible to construct a major heap leach pile on the surface of a conventional tailings pond.

Jan 1, 1987

By M. M. Ragin, B. J. Scheiner

The US Bureau of Mines (USBM) has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. It was found that at a given polymer concentration, there were an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

Simulation models were developed at the Julius kruttschnitt Mineral Research Centre to provide accurate estimates of power consumption for a wide range of equipment. With the models, a range of circuits and operating conditions can be compared by simulation for a particular ore type. Accurate models of classification allow for the interaction between classifier efficiency and target product size (e.g., P80 or percent passing 150 /an) to be considered. This paper considers a range of circuit types and overall energy efficiency in the context of case studies where different circuit types were treating similar ore types.

Jan 1, 1999

By Peter C. Lighthal, Harvey N. McLeod, Iain G. Bruce

This paper describes the practical aspects of handling cyanide leach tailings. Alternative systems for cyanide destruction are briefly discussed. The provision of adequate retention time to allow natural degradation of cyanide during summer months is the most economical method of cyanide destruction. Cyanide in ground- water can frequently be both persistent and mobile, so that tailings basins should be designed to limit seepage. Common methods for limiting seepage are presented. Other aspects addressed are water balance, winter operation and abandonment of cyanide tailings systems. A case example of the Cheni Gold Mines Lawyers Creek Project tailings handling system is presented.

Jan 1, 1987

By Gao Zhizhong, Zheng Shibo, Gu Zhengxing

Extensive research on the beneficiation of Florida dolomitic phosphate pebble has been carried out by Lianyungang Design and Research Institute of China (CLDRI) in recent years. Test results indicate that the fine-particle flotation process could be used to effectively recover the phosphate values from Florida high-dolomite phosphate resources. With the CLDRI fine-particle flotation technology, a phosphate concentrate with 31% P2O5 and less than 1% MgO could be obtained from a flotation feed containing 25.8% P2O2 and 2.2% MgO at an overall P2O5 recovery of up to 85%.

Jan 1, 1999

By Kirk Conway, Richard L. Unger

The U. S. Bureau of Mines conducted a research project to analyze the design of underground mining equipment with respect to ease of maintenance and maintainer safety. The work included a review of maintainability design literature, an analysis of maintenance related accident data, field reviews of equipment designs, and interviews with mine maintenance personnel and equipment manufacturers. Based on the findings, a set of maintainability design recommendations have been prepared. The final recommendations document includes maintainability engineering information for equipment designers, as well as a buyers' guide to aid purchasers of mining machinery in evaluating the maintainability of equipment.

Jan 1, 1992

By Andrew J. Neale, Mark Franklin, Mike Cooper

Although recent advances have significantly improved our understanding of flotation fundamentals, disturbance variables combine to make it difficult to maintain steady state operating conditions over either the short or long term. One of the major concerns relates to knowing how much reagent to add to the flotation system, how to monitor the addition rate, and how to determine when to adjust the reagent addition rate in the presence of these disturbances. This paper will look at the development and installation of process control systems that address these issues. The economic benefits that accrued from the implementation of these strategies is described.

Jan 1, 1994

By D. Lenartowicz, K. R. Alexander, M Collings

Cosmo Howley is a gold deposit in the Northern Territory of Australia. The geology is complex and the input of geological data is an important part of the grade control process. As the geology of the deposit has become better understood, grade control and mining techniques have evolved to meet the changing circumstances. Present grade control depends on the use of angled blast holes, 21/2 benches and selective mining. Data is processed on site using 2 386 PC's running Surpac software. An environmental protection programme is employed, including soil stripping and stockpiling, sulphide waste containment and water quality monitoring.

Jan 1, 1989

By H. Pieterse, K. S. Fraser, J. R. Goode

The Goldstrike autoclave plant is designed for the pressure oxidation of 1363 t/d (1500 stpd) of refractory gold ore. The plant was commissioned in early February 1990 over a one week period - an unusually short period for a plant of this complexity. The rapid plant start-up is attributed to certain detailed design and control aspects of the plant. This paper discusses key features of the autoclave plant with emphasis on the design of the splash/flash system of heat recovery and the control systems. Commissioning and plant operations over the first three months are reviewed.

Jan 1, 1990

By Heiskanen K., Koivistoinen P.

A common belief is that autogenous grinding suits itself only to certain oretypes. It is shown that properly designed autogenous grinding can be used even with very difficult ores with energy consumptions which are equal or lower than obtained with rod-ball mill grinding. The basic feature in the design is the large port grate developed by Outokumpu. The scale-up of the mills can be done on the basis of the base mill concept. It enables to compare different mill sizes and types. Simple scale-up equations are presented based on actual mill data and experimental work.

Jan 1, 1992

By S. O. Yuan, R. L. Grayson

As a followup to a USBM-sponsored research project, the authors utilized the knowledge-base structure and system concepts from a Sun Sparcstation-based worker-scheduling system of the mine-management support system to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, including their availability and work priorities during a shift. The system can optimally allocate manpower on a work shift and can delineate supervisory training responsibilities. The various components of the software, including enhancements made to the original system, are described in detail.

Jan 1, 1998

By Pascale St-Germain, Michael Li, Lionel J. J. Catalan

The oxygen flux into water-covered reactive sulphidic tailings is required for evaluating the long-term performance and predicting the quality of engineered shallow water covers. This information can also serve as an input to the design of water covers for reactive tailings decommissioning. This paper describes some dissolved oxygen (DO) profiles recently measured in the field across the tailings/water interface and oxygen fluxes derived from these profiles. These fluxes are compared with previously reported flux values from similar field measurements. Techniques and pitfalls for measuring DO profiles and calculating oxygen fluxes are also discussed.

Jan 1, 2000

By Guerry H. McCullen, Bruno Despujol

Quartz and phosphate grains from concentrates and ores from Atlantic Coastal Plain sediments often are wholly or partially coated by humates. Coatings were studied in situ using infrared microscopy, by transmission Fourier transform infrared of extracts, and scanning electron microscopy. The 14C age of the coatings is about 20,000 years, much younger than the mineral substrates. Coatings on double flotation concentrates indicate that the conditioning pH may be too low, allowing coated quartz grains to follow phosphate grains through beneficiation. Organic matter from coatings may contribute to processing problems as well as affect final product quality.

Jan 1, 1999