Search Documents

By Richard W. Kimball, Fred B. Estep, Dwayne E. Easterling

This paper discusses the overall challenges to construct a 15,125.7 m (49,625 LF),wastewater drainage tunnel in Cobb County, Georgia by a joint venture of Gilbert Southern Corp. and S.A. Healy Co. and a construction manager Parsons, with Jacobs Associates as a subcontractor. The goal of the project is to provide wastewater retention during peak usage and is connected to a treatment facility near the Chattahoochee River. The primary component of the project is the TBM-driven hard rock tunnel. Additional works include drill and blast areas; four intake interceptors, two construction shafts and a 33.5 m (110 ft), diameter pump station shaft.

Jan 1, 2003

By Anthony J. Stewart, Jim W. Rosteck

This paper will discuss some of the equipment used to construct the middle segment of the MetroWest Water Supply Tunnel. The $252 million, seven-year project located in Framingham, Massachusetts consisted of two hard rock TBM drives worked from a single shaft. The 24,407-foot long west heading was constructed at the same time as the 35,006-foot long east heading. Also included was raise bore construction of four, 30-inch diameter steel lined riser shafts, one 12-foot finish and one 10-footfinish shaft as well as two major valve chambers. The main shaft was 400-feet deep and 32-foot diameter.

Jan 1, 2001

By K. M. Atencio, T. Pike, S. Forrest

We will introduce the Small Business Liability Relief and Brownfields Revitalization Act, which is an amendment to CERCLA and the types of sites it includes and excludes, especially as related to mine-scarred land. We will also describe the types of available funds, whether they are competitive or not, what entities are eligible to receive them, and how to access them. We will introduce the legislation’s liability provisions; for example, the recently issued interim guidance clarifying some of the conditions that contiguous property owners, bona fide prospective purchasers, or innocent landowners must meet to qualify for the liability limitations provided in the Brownfields Law.

Jan 1, 2004

By T. Mudder, K. Harvey

The objectives for closure of a hard rock mine include minimizing long term environmental liability, attaining regulatory compliance, and maintaining geotechnical stability, while closing as cost-effectively as possible. Proper planning for closure should come during the feasibility study, design and permitting phases, and during operations as updates. The lack of a proper or updated closure plan can result in severe environmental and economic consequences. Effective mine closure is the result of a combination of innovative concepts, long-term commitments, and multi-party cooperation. The purpose of this paper is to discuss concepts, commitments, and cooperation as they relate to an effective closure plan.

Jan 1, 1999

By Robert S. MacPhail, Bret G. Cousins

Many copper-bearing ores with associated gold use Sodium Isopropyl Xanthate (SIPX) as a flotation agent. In general, SIPX will float to some extent other minerals that may not be desirable, such as pyrite. FLEX 31 is a chemically enhanced SIPX product with many of the same properties as SIPX. But FLEX 31 has the ability to reject more pyrite from concentrates and improves copper recovery when using up to 50% less FLEX 31 than is required if using SIPX. Copper activated minerals such as sphalerite and arsenopyrite show increased recoveries as well using FLEX 31. Tests have been performed on copper/zinc ores and an arsenopyrite/pyrite ore.

Jan 1, 1995

By Leslie S. Rubin, John C. Roberge, Mackenzie Burnett

A self regulating helical inducer has been developed and tested for dry injection of coarse or fine solids into a hydraulic pipeline. This centrifugal pumping device has also been modified and tested for use as a boost pump in medium and long distance pipeline haulage systems. The helical inducer has been operated as an integral component of a slurry injection vehicle. This compact, low profile vehicle also includes crushing and screening components, solids feeding components, a track drive system for mobility and is run by a single operator. The helical injector and boost pump operate without speed and flow controls allowing for the practical hydraulic transport of excavated materials.

Jan 1, 1983

By James A. Pappas, Francis L. Fong, Tracy K. Lundin

The impact of environmental regulations on the quality of tunnel groundwater discharges is examined in this paper. Tunnel contractors usually depend on specialty contractors or outside consultants to deal with this issue without carefully examining their activities to minimize the production of contaminants. This approach may not be adequate given increasingly more restrictive environmental requirements. This paper surveys the general practice of the tunneling industry and attempts to identify sources of contaminants which may affect the total suspended solids, oil and grease content, and pH of the discharges. Strategies for treating the discharges are included. Field data and observations from several tunneling projects are also presented.

Jan 1, 1995

By Paolo Massacci, Marco de Nardis

SPL (Spent Pot Linings) are hazardous waste. The described work seeks to identify simple and inexpensive processes for recovering the recyclable materials and thereby both reduce the volume to be handed to the dumps and produce a waste that belongs to a less dangerous class. For this purpose a study was conducted to characterise the structure of the cell and the refilling elements at the end of the Aluminum process. The properties of the material that make up the SPLs were determined in order to apply the related selection procedures. The study permitted the design of treatment process able to reduce the negative environment impact of the aluminum production cycle.

Jan 1, 1995

By Jozef F. Zurawski

The paper discusses design and construction of a 1.8 meter (6 ft.) diameter tunnel installed under complex geology of Staten Island, New York. Contract T-13 is a section of the Oakwood Beach Water Pollution Control Project constructed for New York City Department of Environmental Protection. A knowledge of the subsurface conditions and difficulties experienced on the adjacent contracts called for an innovative approach to handle tunneling under 12 to 17 meters (40-55 ft.) of water in the variable subsurface conditions. This paper describes tunnel design and construction utilizing continuous grouting during advancement of tunnel boring machine and installation of liner plates.

Jan 1, 1993

By Jacques L. Mauboussin

The EUROPEAN ORGANIZATION for NUCLEAR RESEARCH (CERN) has undertaken the construction of a LARGE ELECTRON POSITRON COLLIDER (LEP), near GENEVA (Switzerland). The facility includes the main 27 km long tunnelled ring, 18 shafts, 20 experimental caverns and many auxiliary galleries. Roughly 800 000 cu.m were excavated in the molasse at 50-140 m depths, using roadheaders for caverns and auxiliary tunnels and 3 WIRTH, 4.5 m diameter, fullface TBMs for the main circular tunnel. Each TBM performs 25-30 m/day. Provisory lining behind them uses either precast concrete elements or shotcrete. Works a e being carried out by a joint-venture of European contractors led by FOUGEROLLE (France).

Jan 1, 1987

By S. Michael Feroz, Paul Gribbon, Jan Rosholt

Approximately six billion gallons of combined sewage are discharged annually into Willamette River and Columbia Slough through Portland’s combined sewer system. The Columbia Slough Consolidation Conduit (CSCC) is an important element of mandated Combined Sewer Overflow (CSO) abatement. It includes2,548m (8,361 ft.) of 3.7 m. (12 ft.) internal diameter tunnel. The CSCC alignment traverses the UP railroad, Columbia Boulevard and parallels an old sewer. Geologic conditions include river alluvium and fine to coarse-grained flood deposits containing cobbles and boulders. This paper describes design and construction of a tunnel in soft-ground, with shallow cover and close to an old concrete sewer.

Jan 1, 1999

By B. P. Atkin, D. W. Brown

A handleability monitor was designed to provide a simple, rapid, on-site assessment of the whole or part consignment of a coal blend in its "as-received" condition. The monitor was evaluated at a number of coalhandling plants, which handle both metallurgical and power station coals from a variety of sources worldwide. The results can be used to predict which coals could routinely pass through a handling plant at line capacity without causing blockage or delay. Despite extensive analysis of the data, it was not possible to correlate the handleability index to the regular sample analysis of moisture, ash and size analyses of the coal blends.

Jan 1, 2002

By S. Hartwig, K. Wohiwend, J. Forsberg, G. Bergling

New, larger cutters requiring higher operating loads and thus increased cutterhead thrust, higher cut¬terhead speeds and more pronounced demands of maintaining high penetration rates also in mixed ground, constantly augment the loads on TBM main bearings. At the same time, the demand of a single TBM model covering a wide diameter range limits the available space for the main bearing at the smaller end. Innovative concepts and advanced methods of calculating bearing loads and lifetimes are needed to meet the demands which TBM suppliers and their customers face. This paper reviews different design approaches and covers the influence of lubrication on bearing life and condition monitoring as well.

Jan 1, 1995

By W. G. Courtney

The prevention of frictional ignition with a ripper-type continuous mining machine using conical bits was investigated in the laboratory using cutter-drum-mounted water sprays. Results indicated that frictional ignition during dry cutting of sandstone with conical bits was readily obtained even at low drum rpm, while wet cutting with a carefully-designed water spray nozzle located behind the bit substantially reduced the likelihood of frictional ignition. However, the orientation and operation of the spray nozzle is critical and involves almost no margin for error. A Lee-Norse 265 ripper drum has been modified to include durable water seals and is presently being field tested underground.

Jan 1, 1987

By Karl Kuhnhenn

One substantial element of the NATM is to take into consideration the geotechnical rock behavior in the design of excavation and support methods. Even if this opinion is being shared increasingly, the stress analysis is not the sole criterion for a successful tunnel drive. By the beginning, the inventors of the NATM have clearly defined a number of principles which have kept their validity until now. The evaluation of different failure cases demonstrate how necessary the observance of these principles and their strict following during execution are besides the stress analysis. The great number of successfully excavated NATM tunnels are an impressive evidence for these principles.

Jan 1, 1995

By S. L. Jung, T. L. Nichols, K. Prisbrey

The problem was to evaluate the on-line detection of rock properties through acoustic emission sensors. Acoustic emission sensors, when attached to crushers, grinders, and roof bolters, are robust, economical, and relatively maintenance free. Our objective was to relate acoustic emissions to rock fracture mechanisms, including micropore closures, linear elastic deformations, and crack propagation. We evaluated acoustic emissions from steel jacketed rock cores during indentation tests. In addition we attached sensors to the rotating shaft of a rock bolter drill. A back propagation neural network "learned" rock fracture characteristics and rock type with 99% classification accuracy. A neural network's calibration and computational abilities suggest better acoustic emission sensor capabilities.

Jan 1, 1993

By M. Ghiani, R. Peretti, A. Zucca

The paper deals with the experimental application of a pilot flotation column to baryte and fluorspar ores. The column has been installed in parallel with the cleaning stages of two different industrial flotation plants where the above ores are processed using conventional cells with mechanical impellers. The effect of several parameters, including froth height, wash water additions, pulp feedrate and air supply rate, has been investigated. It has been shown that by finely tuning the above parameters good flotation performances can be achieved. The experimental results demonstrate the greater versatility of the column flotation and its superior separation efficiency, especially for the fine particle size fractions, over conventional cells.

Jan 1, 1995

By G. J. Lindenburg, T. L. Wilson

The Velvet uranium mine is located in the Big Indian district of the Colorado Plateau. The uranium ore body lies within the lower Triassic Chinle Formation, and the ore is associated with west-south-westerly trending fluvial sand systems. Exploration and mining are directed by longhole drilling and radiometric sampling. Results of the gamma probing, face scanning, and geologic mapping guide mining decisions and planning. Three people are directly involved with the geologic procedures: two geologists and a mine supervisor. The two geologists map, do rib scans, and direct longhole drilling. The third man involved, the mine supervisor, has last minute directive action based on shot hole probe data.

Jan 1, 1992

By A. Guan, K. N. Han, J. J. Kellar, D. A. Boyles

Metal ions associated with effluent streams pose an increasing environmental problem for the mineral industry. Various techniques currently in use to combat this problem including bioremediation, chemical precipitation, and ion exchange are reviewed, and their relative advantages and disadvantages discussed. An alternative technique for metal ion removal, adsorption on surface modified alumina substrates is presented. Alumina surfaces were modified by adsorption of organofunctional silanes, and metal ion removal occurs by chelation of the ion by the adsorbed silane molecules. Experimental data is presented for the removal of cupric ions by this method and is compared to cupric ion removal by adsorption on alumina without prior surface modification.

Jan 1, 1994

By R. L. Urie, L. Burdzinski

Non-operational mine facilities are subject to placement on the EPA's National Priority List (Superfund). Once a mine site is undergoing investigation and/or remediation, MSHA regulations for health and safety may no longer be applicable. This paper addresses the changes in the applicable and relevant standards that apply to health and safety and public health related to site contaminants. The implementation of health and safety plans, and the development of public health risk assessments are described. Examples are presented from Superfund activities at the Eagle Mine, near Minturn, Colorado; the Anaconda Smelter near Mill Creek, Montana; California Gulch near Leadville, Colorado; and Bunker Hill, Idaho.

Jan 1, 1991