Search Documents

By Robert Kimutis, Heather Dougherty, Eric Watkins

Gas wells have often intersected mining resources, but unconventional shale well drilling has more recently challenged mines to balance the risk of interaction due to higher pressures and larger quantities of gas. Full extraction mining, such as the longwall method, induces ground movement that may influence the casings if wells are drilled within the mining area. The possibility of a casing shear would lead to the risk of unplanned gas migration into the mine. This has the potential to quickly overcome the ventilation system and reach the explosive range which, if ignited, can have catastrophic consequences on the health and safety of underground workers. The utilization of network software to model mine ventilation is a common practice in the mining industry as a predictive tool for planning and monitoring and can assist with a well breach scenario over a large mining area. This work focuses on a well breach in between two longwall panels after second panel mining with gas entering primarily through the gobs of the adjacent longwall panels. Applying the network software Ventsim, a gob zone and ventilation network were created to better understand the distribution of gas within the mine and the limitations and effectiveness of a ventilation system. The model shows both a transient flow simulation and steady state concentrations throughout the mine ventilation system. Using a standard Pittsburgh coal seam longwall ventilation scheme, we find that the system can dilute a significant inflow of up to 700 cfm of methane.

Oct 12, 2023

By Stephen V. Thompson

Within recent years portable seismic refraction units have found their place in the industry for shallow investigations, Completely portable, relatively inexpensive and of proven accuracy, the portable refraction seismograph is an electronic tool in an electronic age. The age of electronic instrumentation has seen the development of seismic reflection and refraction equipment for deep exploration, especially in the petroleum industry. Large, expensive units, normally truck-mounted and utilizing explosives, are being used successfully for this type of sub- surface investigation. The portable seismograph utilizes the same theory for shallow work as that applied to deep refraction seismology.

Jan 1, 1964

By Ray E. Harris

Introduction A resource of more than 122 Gt (134 billion st) of minable trona and mixed trona and halite underlies an area of about 3400 km2 (1300 sq miles) west of Green River, WY (Culbertson, in preparation) (Fig. 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6 Mt (6.7 million st) (Kostick, 1983). About 90% of this came from Wyoming trona. This enormous deposit occurs in the Wilkins Peak Member of the Green River Formation that is of Eocene age. This formation is derived from sediments deposited in a large lake named Gosiute. Lake Gosiute occupied the Green River Basin in southwestern Wyoming some 38 to 54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition when the trona deposits were formed. A total of 42 trona beds are known. Of these, 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation). The production of sodium compounds from the trona deposits in the Wilkins Peak Member began in 1896 when wells were drilled within the present boundaries of the town of Green River. The purpose of the drilling was for extraction of sodium carbonate brines. Sodium carbonate (sal soda) was removed from these brines at a plant in Green River. Bedded trona was discovered in 1938 in a core from an oil well drilled south of Westvaco. In 1947, the underground mining of trona began. Production has continued from 1948 to date. Currently, five companies are mining trona and producing soda ash from the Wilkins Peak Member in Wyoming. Additionally, Allied Chemical Co. mines and processes trona for Church and Dwight's sodium bicarbonate (baking soda) operation in Green River. Competition in the soda ash industry depends primarily on the efficiency of mining and refining, allowing for lower-cost production. Newer plants and mine designs should increase efficiency. Solution mining holds promise as an even lower-cost method of mining. Employment in the soda ash industry is declining since the newer mining and refining methods are less labor intensive. Declines in employment, however, may be offset as production increases. Due to the large resource, the availability of minable trona should not be a problem for perhaps hundreds of years. Geology of Wyoming trona deposits Forty-two beds of trona or mixed trona and halite occur in the

Jan 10, 1985

By J. Winterton

Cripple Creek and Victor Gold Mining Co. is developing a full-scale pad injection program as part of the overall operational plan for the Valley Leach Facility. As part of the development process the mechanics of the injection methodology are evaluated in the context of physical injection measurements, outcome from geophysical monitoring, and gold leaching theory. The results indicate that hydraulic fracturing analogies advanced heretofore do not accurately describe injection phenomena in unconsolidated and noncohesive material typical of leach pads. A new interpretation is presented and extended to define operational strategies for maximizing gold production.

Feb 27, 2013

By M. G. Gorman

The effects of particle size, particle shape and degree of aggregation on n-dodecylamine flotation of -20 µ m quartz and glass beads were studied. A microflotation cell suitable for use with very fine particles was used in the flotation experimentation. Degree of agglomeration of particles was estimated by comparing size distributions of the quartz and beads in a dispersed system to size distributions in systems in which the collector was present. Results obtained show that in such flotation systems the fine particles are not generally present as individual particles during flotation but rather as aggregations. However, the quartz floats more readily than the beads indicating that there are some shape effects in the systems, considering the large specific surface areas of the materials it also appears that substantial amine consumption in the systems may limit flotation or lead to a requirement of greater reagent dosage for equivalent flotation to that tor larger particles.

Jan 1, 1990

By G. Knight

It is shown that the dust exposure of all underground workers varies greatly from day to day even though each man did the same job in the same working place each day. The variability follows a logarithmic normal distribution with a geometric standard deviation of about 1.6 for the three dust assessments; total respirable dust, respirable combustible dust and respirable quartz dust in both mines studied. The variability was homogeneous for all men and most jobs. The differences between men doing the same job was found not to be significant and it is suggested that the dust sampling program should determine the average for each job and use this as the best estimate of the exposure for each man.

Jan 1, 1980

By D. N. Trerice

The Electric Power Research Institute (EPRI) is sponsoring the construction and operation of a coal cleaning test facility at Homer City, Pennsylvania. The facility represents a major investment by the electric utility industry to advance the state of the art of conventional coal cleaning technology. The facility is unique in design and can process large quantities of coal in conventional flowsheet configurations, simulate full size plant conditions, and perform open and closed loop performance testing on conventional and advanced coal cleaning equipment. Computer operation will also be demonstrated. The facility objectives, initial complement, and operating plane are discussed as they relate to other coal cleaning projects at EPRI.

Jan 1, 1981

By Antoni Kalukiewicz

From 1997 through 2000, a team of Polish experts headed by the author studied the prospects of mining newly discovered emerald deposits in Afghanistan. This article describes the scheme for mechanization of the mining operations, along with improvements made to the ventilation facilities and lighting. The required equipment was flown to Afghanistan and the Afghan miners were trained in machine operation and maintenance.

Jan 1, 2005

By K. V. Raj, VASU GANGRADE

Airflow in large-opening stone mines is largely dependent on the natural ventilation due to the large cross- section area of the opening. The openings of such stone mines are typically twice or thrice the size of typical underground coal or metal/nonmetal mines. Due to the influence of natural ventilation, air velocities as well as the static pressure drop in the mines are low. Mines rely on auxiliary fans to ventilate active faces to reduce contaminant exposure to mine workers. The National Institute for Occupational Safety and Health (NIOSH) is conducting research on ventilation of large-opening stone mines to reduce worker exposure to dust and other contaminants such as diesel particulate matter (DPM). In order to reduce worker exposure to dust and DPM, an understanding of the airflow pattern due to auxiliary fans in the mine is needed. Under this research, NIOSH researchers are exploring the computational fluid dynamics (CFD) modeling to understand the airflow behavior in large-opening mines. In this paper, the team is presenting the results from three-dimensional CFD modeling of airflow in a large-opening stone mine and investigating the effect of a fan placement with the movement of trucks.

Feb 1, 2025

By John Barber

The Deep Ore Zone (DOZ) Mine is PT Freeport Indonesia's (PTFI) newest operation. Production at the mine began in September 2000. The DOZ Mine produces 25 kt/d (27,500 stpd) using mechanized block cave mining methods. The DOZ Mine has several major improvements when compared with previous block cave mines in the district. It has an independent and improved ventilation system, a flexible and efficient truck haulage system, and a more reliable crushing and conveying system. PTFI's copper and gold mining complex is located in the Ertsberg mining district in Irian Jaya, Indonesia (Fig. 1). The Ertsberg district is located in the Sudirman Mountains at elevations from 3,000 to 4,500 m (9,800 to 14,700 ft) above sea level. The topography is extremely rugged and rainfall in the mine area averages 3,000 mm/a (118 in./year). Freeport began production in the district in 1972 when the mill began processing ore from the Ertsberg openpit. Underground mining began in 1980 when the Gunung Bijih Timur-Ertsberg East (GBT) Mine was brought online using block caving methods. In 1991, the GBT Mine reached a maximum production rate of 28 kt/d (31,000 stpd). Ore from the mine was exhausted in 1994. The Intermediate Ore Zone (IOZ) was brought into production in 1994. It, too, used block caving methods and had a design rate of 10 kt/d (11,000 stpd). The IOZ is currently producing at a rate of 21 kt/ d (23,000 stpd). The DOZ was discovered in the mid-1980s by deep drilling from the GBT. The GBT, IOZ and DOZ deposits are all situated in the Ertsberg East Skarn System (EESS). In 1993, the first of several studies was completed that indicated that portions of the DOZ Mine could be economically mined using block caving methods. Limited development was started in 1995. Full-scale development and construction began in late 1997. The crusher and conveying system began operating during the first quarter 2000. The first of two main exhaust shafts has been com¬missioned, along with three of the four new main fans. The second exhaust shaft and fourth main fan will be in service by the end of 2001. Undercutting and production began in September 2000. The DOZ Mine will reach its design production rate of 25 kt/d (27,500 stpd) in 2003. A study is under way to determine if an ultimate production rate of 35 kt/d (38,500 stpd) is feasible.

Jan 1, 2001

The Rasmussen Ridge phosphate mine is owned by Agrium CPO and operated by a unit of Washington Group International. The mine, located in southeastern Idaho, received the Idaho Inter-Agency Reclamation Award from the Idaho Department of Lands. The phosphate mine, located northeast of Soda Springs, was honored for “Excellence in Ongoing Operations, Soft Rock Mines over 75Acres.” Charles Ross is Agrium CPO’s plant manager. He said, “We are honored to receive this award. This recognizes the commitment and dedication of our employees toward the protection of the environment. I am really proud of the people that work at the mine.”

Jan 1, 2005

By P. Schumacher, M. Fein

"INTRODUCTION Newmont’s Twin Creeks operation, part of its Nevada operations, produces gold from two large open pit mines. Mined ore is processed at one of three on-site facilities: a refractory mill with two autoclaves, an oxide mill and heap leaching facilities. Twin Creeks also processes various off-site sourced concentrates and ore including high grade underground ore from the Turquoise Ridge joint venture with Barrick Gold Corporation. This paper discusses Twin Creeks’ strategic mine planning process which is part of an in-depth continuous improvement program called “Full Potential.” The process involves cost analysis, phase design validations, life-of-mine production scheduling optimization, mill blending strategy and stockpile management. Through this Full Potential strategic planning, Twin Creeks is creating significant value by increasing near term free cash flow and life of mine net present value (“NPV”) and achieving cost reductions. TWIN CREEKS OPERATION Twin Creeks is one of the major gold producers in Newmont’s Nevada operations (see Figure 1, 2 and 3). Located approximately 15 miles north of Golconda, Twin Creeks produced approximately 28 % of the Nevada operation’s 2013 gold production of 1.8 million ounces (Newmont 2014). The production included Turquoise Ridge sourced gold ore from the joint venture (75% Barrick Gold Corporation, 25% Newmont).At Twin Creeks, there are two large open pits, named Mega Pit and Vista Pit (see Figure 4, 5 and 6). There are 3 to 5 phases in Mega Pit and 2 to 5 phases in Vista Pit depending on the gold price assumption. There is also an underground exploration project at the bottom of the Vista Pit. Twin Creeks produces gold from a variety of ore types requiring different processing techniques depending on economic and metallurgical characteristics. To ensure the best use of processing assets, engineering and processing groups at Twin Creeks utilize a Mixed Integer Linear Programming (“MILP”) model to guide the flow of mine sequences and material routing to various process facilities (Kawahata, Schumacher and Hufford 2013)."

Jan 1, 2015

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL

The steepness of an openpit mine’s slopes has a substantial influence on the mine’s financial return. This paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice, pitwall profiles are often planar in cross section within each rock layer: that is, the profile inclination across each layer tends to be constant. Here, instead, a new geotechnical software, OptimalSlope, is used to determine optimal pitwall profiles of depth-varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and factor of safety (FoS).

By Jonas Svensson

The Grangcold Pellet Process - for which patents have been applied or already granted in a number of countries - uses a hydraulic adhesive such as Portland cement, slag cements, pozzolanic cements, etc., for the production of cold bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron ore fines is not new. Portland cement was proposed as an adhesive for cold bonded iron ore briquettes in patents granted more than 50 years ago (1). In a report on the briquetting of iron ore fines, published in Stahl and Eisen 1959 (2), it is stated that briquettes bonded with Portland cement are used on a small scale at on ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft and difficult to store and handle. The Grangcold Pellet "recess has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrate during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus the mixture can he stored in a stockpile or in a silo until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening.

Jan 1, 1969

By S. Mishra, C. Shon, D. Saylak

Only 40% of fly ash generated by the power plants in US are recycled and used for commercial applications. Of these, the high lime, Class C ash had been preferred. Systematic laboratory and field-scale studies have shown that, by including calcium chloride in the mix design of stabilization of roadbed materials, both Class C and Class F fly ashes can be effectively utilized. Test data reveal that the addition of calcium chloride to the system accelerates its curing rate, thereby increasing early strength and long term durability of the constructed road. For road construction, a preblended Class F fly ash–CaCl2 system tends to be more forgiving than the Class C fly ash–CaCl2 system. The former system produces more durable roads. The role of calcium chloride as an accelerator in these systems is discussed along with a mathematical model developed for fly ash- CaCl2 stabilized roadbed systems.

Jan 1, 2007

By V. M. Lepetic

Large tonnages of copper and molybdenum sulfide ore are treated by flotation. Substantial savings could be realized, particularly in high-capacity concentrators, by use of a simplified flotation technique involving lower reagent consumption. Chalcopyrite and molybdenite from some deposits can be floated by use of only a frother as a single flotation reagent; acceptable concentrate grade and recovery can be obtained. Separation of molybdenite from copper sulfides may become simpler and less costly. The genesis of the ore and the ions present in the flotation pulp liquid phase appear to be the major success-determining factors.

Jan 1, 1972

By Madan M. Singh

A new mining project can raise questions about what effect it will have on the community after it closes. Historically, little was done by communities to plan for and accommodate the changes in the economic infrastructure when a mine project is finished either after the ore runs out or if market conditions deteriorate and make it unprofitable. Projects that were underfunded were generally unable to withstand periodic market downturns. However, data in a recent study conducted by the Seidman Research Institute leads to the conclusion that, even when a mining project is terminated, there can be (and, in the specific case studied, is) a residual beneficial economic effect in the community, which lasts for a long period of time.

Jan 1, 2010

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By J. Platt

Recent EPRI research on utilities? likely strategies to reduce sulfur emissions differs sharply from policy analyses showing all- switching or all-scrubbing choices. Energy Ventures Analysis, with Stearns-Catalytic and A. T. Kearney, estimated sulfur-removal costs for scrubbing or switching at virtually all affected plants in the 31 Eastern States. Cost tradeoffs occur between $30 and $40-plus per ton FOB mine in Central Appalachia ($33-44-plus per tonne). 1/2 to 3/4 of total sulfur reductions comes from scrubbing, whose costs act as a cap on low-sulfur coal prices. In a severe environmental scenario, low- sulfur coal demand evaporates, replaced by very low-sulfur (0.7%) coal demand. Additional findings and implications of EPRI coal supply and market studies will be reviewed.

Jan 1, 1987

By M. J. Beus

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a full-size shaft are underway.

Jan 1, 1999