Search Documents

By S. G. Zahony

The Moris gold deposit resides in a massive ridge-forming sulfide-poor epithermal quartz and calcite vein system and consists of a mineable reserve of four million tons of 2.1gm Au/ton. Post-mineral normal faulting along the hanging wall of the main fissure has caused a hogback-like exposure of the vein, allowing for inexpensive opencut mining. The vein formed between pre-Cretaceous(?) phyllitic clastic sedimentary units in the footwall and Tertiary andesitic volcanic rocks in the hanging wall. Part of the ore reserve is hosted in a Tertiary conglomerate that rests unconformably atop the phyllitic footwall sequence. The original unoxidized vein material contained substantially less than 1 gram Au/ton. A four-fold upgrading of gold occurred by enrichment when gold recrystallization took place in the electric fields of oxidizing pyrite cubes.

Jan 1, 1993

By Jeffery L. Kohler

The research and development of a pattern recognition system which can predict incipient failures and safety hazards in the mine power network is described. An examination of mine electrical safety hazards revealed they are often related to the electrical equipment down-time experienced on mine sections. Based on this, a method is proposed that can improve both production and safety, without compromising either. Equipment failure modes are examined to illustrate how the ultimate failure can be predicted for enough in advance to allow a convenient and safe repair, followed by a discussion of actual monitoring system performance. Finally, the paper is concluded by projections of the system's utility to industry.

Jan 1, 1977

By Gene M. Handel

Today the world is heavily dependent on petroleum for its energy. In the United States, over 75% of the primary energy used comes from petroleum. Other developed countries are similar. The less developed countries have a lower dependence on petroleum just as the United States did through the early 20th Century. However, these less-developed countries look upon petroleum as one of the primary energy sources for the economic growth required to improve their standard of living. So everyone considers petroleum an essential ingredient in the recipe for the good life. But there is a substantial problem with this recipe, and it is finally getting general recognition. Petroleum is a finite resource, and the world is using it up at a rapid, accelerating rate. Though it won't be exhausted for many decades, the early warnings of ultimate limits have already appeared. The suppliers of the incremental production in the Middle East have threatened to restrict increases in their production rates. And, of course, the short term embargo of four years ago clearly demonstrated the economic impact of reduced access to petroleum as a primary source of energy. World petroleum production will probably peak in. 10 to 15 years and then start declining. When that happens, economics--the allocation of scarce products (also known as the dismal science for obvious reasons)--indicates that the price of petroleum will escalate in real terms. So that's the situation today. We have a serious and growing problem facing us that could substantially alter the quality of our life over the next 25 years. Recognition that the society may face a period of lowered expectations after a long period of upward mobility will be a painful experience, but it is certainly not the moral equivalent of war. And, besides, we have time to take positive actions to avert the most serious consequences. When we consider alternate energy sources, the possibilities are almost endless: coal, oil shale, tar sands, solar, fission, fusion, wind, tides, biomass, etc. Actually, the list is endless because new possibilities are continually being proposed. Of these possibilities, coal uniquely stands out as an attractive substitute for petroleum. Coal can be, and is, burned to generate electricity and provide heat. It can be liquefied to supplement the liquid fuels from petroleum, and it can be gasified for use as synthetic natural gas. Unlike exotic alternate energy such as solar and fusion, coal has successfully been used commercially to produce synthetic fuels. But, the technology does need to be refined and modernized. Thus, coal's role is not to be "America's Ace in the Hole," but to bridge the transition from primary dependence on petroleum for energy to the utopia of renewable sources of energy. But don't be mislead by the prophets--those renewable sources of energy are going to be very, very expensive when they are invented.

Jan 1, 1978

By J. A. Halt, E. Larsen

"The Sydvaranger magnetite mine closed in 1996 due to low iron ore prices and was reopened in 2009. The flowsheet has remained more or less as in the old plant, based upon two grinding steps followed by magnetic separation. The magnetite is free of harmful elements and should be attractive on the high quality market. This requires a concentrate containing less than 2% SiO2, which previously was achieved by amine flotation. Amine was preferred because it could be used with sea water. The use of amine is now restricted by the Norwegian Climate and Pollution Agency. Therefore, testwork to replace cationic with anionic flotation was done. Activation of quartz with Ca or Mg ions prior to anionic flotation was shown by research from 1960 to 1980 to be effective under laboratory conditions. The old research results have been followed up in order to make a commercial process for Sydvaranger. Calcium activation works excellently with all Sydvaranger ores, including the ones containing amphibole minerals, but Ca activation requires the high and not environmentally friendly pH of 12.4. Magnesium activation at pH 10.5 is a little more challenging, because the maximum concentration of MgOH+ is about 100 times lower than that of CaOH+. Fortunately, the major impurity in the main Bjornevatn orebody is quartz, which responds well to Mg activation. The process does not appear to depend much upon water quality, as the silicates may already be activated during grinding and magnetic separation in recycled water. The new process is environmentally friendly, as only well-known household reagents are used; oleic acid or tall oil, dextrin, sodium hydroxide and magnesium chloride at pH 10.5.IntroductionThe processing plant of Sydvaranger Gruve AS (SVG) is located in the port town of Kirkenes in the northernmost part of Norway, 10 km by rail from the high-grade deposit of Bjornevatn. This plant has been able to beneficiate magnetite ore to up to 99.5% purity, as described by Sandvik and Malvik (2001). Using the magnetic properties of the ore and making the most out of its enviable liberation characteristics, the original plant consisted of ball mills and 600-mm magnetic separators. The plant was shut down due to market conditions in 1996 but reopened in 2009."

Jan 1, 2015

By B. Berg, J. Stephenson, J. Mansanti, C. Nyikos

"Intrepid Potash, Inc.’s Carlsbad East facility has refined sylvite and produced muriate of potash (MOP) since 1965. In addition to MOP, Intrepid Potash began recovering the mineral langbeinite from a mixed ore reserve in 2005. In 2011 a new langbeinite recovery process for the coarse (+850 micron) size fraction was constructed to enhance the overall langbeinite recovery. Based on the limited mixed ore reserve and an abundance of langbeinite ore reserves the transition of the East plant to a langbeinite only facility was targeted for 2021. Due to a decreasing grade of the mixed ore reserve, declining sales pricing, and high sylvite operating costs a strategic decision was made to accelerate this transition into 2016. To enable a successful transition, a fines recovery system needed to be developed, constructed and implemented. This paper describes the advancement of langbeinite processing at Intrepid Potash and the planning, development and successful execution of the transition to a langbeinite only operation. BACKGROUND Langbeinite (K2SO4·2MgSO4) is a double salt containing potassium sulfate (K2SO4) and magnesium sulfate (MgSO4). It is used as fertilizer and in the industry is described as Sulfate of Potash Magnesia. It is attractive as a specialty fertilizer and in addition to containing a ready source of a primary nutrient potassium, it also provides two secondary essential nutrients, magnesium and sulfur. It is especially attractive for chloride sensitive crops. Langbeinite has a specific gravity of 2.8, a Mohs hardness of 4.2, and is brittle thus very friable. It is the hardest of the saline minerals, and despite its relative softness on the Mohs scale can be very abrasive in process environments and in field applications, probably due to its conchoidal cleavage. Its solubility at 240 g/l is less than the solubility of sylvite (KCl) or halite (NaCl) and due to even slower relative dissolution kinetics washing with cold water has been a common practice for upgrading langbeinite ores. The solubilization/crystallization relationship for langbeinite is different from the majority of other evaporite minerals in that once langbeinite is solubilized it does not form langbeinite again. Instead it gives up one mole of magnesium sulfate, takes on various waters of hydration and precipitates out as either schoenite (K2SO4·MgSO4·6H2O) or leonite (K2SO4·MgSO4·4H2O) depending on temperature. Due to its partial solubility and phase transitions at its surface when exposed to moisture, there is strong cohesion between wetted particles; the resulting stickiness of the upgraded products can create significant materials handling issues unless processed in slurry form or at relatively low moisture levels. Langbeinite has been produced commercially from two locations, the Kalush and Stebnik regions in the Cartpathian Mountains of former Poland and now the Ukraine and from the Permian Basin in New Mexico (Garrett, 1996; Smith 1949). Current production is from two operators in the U.S., Mosaic and Intrepid Potash."

Jan 1, 2017

By E. Stemn

Incident investigation is of utmost importance in most high-risk industries. This study was undertaken to study the content of past investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of 5 elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of 3 Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed. INTRODUCTION The importance of learning from incidents is well documented in the literature. For instance, some scholars regard learning from incidents as important for improving safety [1,2]. Thus, many organisations spend considerable resources in identifying lessons from incidents and subsequently on the process of improvement that follows the identification of lessons. It is therefore important for such organisations to determine the effectiveness of their learning from incidents processes, in order to identify specific areas where improvements are needed, so that interventions can be as specific as possible. The learning from incidents process models the plan-act-check-do approach of management systems, often consisting of four major stages, namely; data collection and incident analysis, planning interventions, implementing interventions and follow-ups and evaluation [3,2]. The investigating and analysis of incidents have been regarded as one of the vital stages of the learning process since it is the stage where lessons are identified [3,2,4]. It has also been noted elsewhere in the literature that results of the previous stage of the learning process are important for the next stage [3]. For example, ineffective incident analyses could result in the planning of ineffective remedial measures. One of the primary aims of incident investigations is to identify lessons from previous incidents which when implemented can prevent future recurrences or minimise the effects of future incidents. There is thus the need for organisations to assess the quality of their investigations periodically since it is one of the means they adopt to improve safety and the quality of remedial measures to some extent depends on the effectiveness of the investigations. Although previous studies [5,2] have assessed the effectiveness of the learning process, and some aspects of the learning process, such as incidents reporting, there is less focus on the effectiveness of incident investigations. The research described in this paper was therefore conducted to contribute to this gap, focusing more closely on incident investigation reports.

Jan 1, 2019

By Abdullah Arik

Verification of computer generated reserve models is essential since the computer does not automatically check the validity of methods and assumptions selected by the user and their results. For the computer to do model verification would require an expert system which would perform tests on the model and determine if the model is valid. Since such an expert system is not available, it is up to users to verify the models they develop.

Jan 1, 1995

By M. A. Kaufman

In this paper I will attempt to present an up to date review of the type of exploration' that has previously been carried out in Alaska, discuss some of the more significant past producers and recent discoveries, and suggest some approaches to future exploration. Hopefully this information may be of some use to those parties tempting to evaluate Alaska's non ferrous, non placer, metal potential or contemplating initiation of exploration in the state. II. SUMMARY AND CONCLUSIONS Past production of non ferrous metals from lode deposits in Alaska has been meager considering the size of the state. Since there have been no major lode mines operative in Alaska since World War II, and since logistical conditions vary throughout the state, it is not possible to generalize with respect to mining costs in Alaska as compared to those in other areas. There seems to be little question, however, that a major deposit situated in a reasonably favorable location' could be profitably operating at present. Host of the known metal prospects in Alaska were discovered by early gold prospectors prior to World War I. From World War I through World War II exploration consisted chiefly of surface prospecting by prospectors on a diminished scale, as compared to the early gold rush days, drilling of some prospects by the U.S.B.M,, and occasional mine or prospect evaluations by mining companies. From the end of World War II to the present time, there has been a generally steady increase in exploration by mining companies consisting chiefly of prospect and district evaluations, large scale aerial reconnaissance programs in search of color anomalies, and regional drainage geochemical surveys. The post World War II increase in mining company exploration has not been matched by an increase in conventional surface prospecting.

Jan 1, 1972

By John W. Crawford

The majority of the regulations in Part 75 for underground coal mines have been in effect since March of 1970, almost nine years now. Although there have been some additions each year in specific areas where the need became apparent or the statute required some action, the bulk was promulgated on March 28, 1970 for the purpose of clarifying the statutory provisions of the Federal Coal Mine Health and Safety Act of 1969. Many of those regulations were derived from the Federal Mine Safety Code, or from experience gained by the Bureau of Mines in the enforcement of Public Law 552. Upon passage of the Federal Mine Safety and Health Act of 1977, these same regulations remained in effect and the statutory requirements of the Act placed a responsibility upon the Secretary of Labor to promulgate additional regulations in specific areas not previously covered. The Federal inspectorate has received formal training at the National Mine Health and Safety Academy in the proper application of the regulations, as well as routine retraining and special training courses subsequent to the promulgation of new regulations. With some exceptions, the vast majority of these regulations are nothing more than good mining practice. Basically, the regulatory problems are two-fold. There are a few specific regulations that, under certain circumstances, compliance is nearly, if not actually, impossible. There is non-uniform application of enforcement of regulations by the inspectorate based on opinions developed from personal experience of inspectors or lack of experience. The record is replete with examples of overzealous inspectors applying regulations that either do not exist or have been stretched far beyond the intent of the regulations.

Jan 1, 1979

By David J. Hatem, K. Bhattarai

The increasing popularity of alternative methods in delivery of underground infrastructure projects has given rise to innovative and collaborative contracting strategies to allocate and manage the unique risks associated with the work. This paper presents approaches and recent examples of how risk has been dealt with using various alternative delivery methods, including Progressive Design Build (PDB) and Construction Manager/General Contractor (CM/GC). Based on the experience gained from these examples, recommendations for an innovative and collaborative risk baselining approach using contingency sharing are presented that should advance the overall goals of equitable risk sharing and compensation.

Jun 13, 2023

By Leonel Lopez

Throughout Mexican history, mining has been an important, traditional activity. Before the "Discovery of America," native miners worked a variety of deposits throughout the country, including Mixtec gold and gem mines in Oaxaca State and Aztec gold, silver and copper from mines in Michoacán. The 500th anniversary of Mining in Mexico after the "Discovery of America" was initiated by the Mexican mining sector on April 15, 1991. As early as 1548, when the Guanajuato mining district was discovered, Mexico had become a leading world producer of precious metals. Since then, Mexican mineral production has developed in cycles, responding to changing technological, economic and political conditions. During the 20th century, Mexican mine output reached its peak in the decades of the 1930s and 1940s, when it was producing about 40% of the world's silver, 15% of its lead, 10% of its zinc, 4% of its copper and 3.5% of its gold. In 1990, by way of contrast, these percentages of world output stood at 13.5% for silver, 4.7% for lead, 4.1% for zinc, 3.2% for copper, and 0.43% for gold. The lowest production levels were recorded during the 1960s and 1970s, when Mexicanization of the industry and increasing state controls weakened mineral economics to a point that mineral exploration budgets were sharply reduced or eliminated, along with the industry's future. Only the noble old mining districts continued to supply production, with occasional eruptions of "bonanzas" and new extensions in established mining districts.

Jan 1, 1994

By M. Duane Lackey

Electric drives hire done outstanding job in many-fields that are related to the mining industry. The equipment that is offered for electric-trucks was developed from the traction equipment which is used on the diesel electric locomotive. Rotating equipment available for use on electric trucks is identical in principle to that which is used on these locomotives. In as far as it is practical, similar controls are used. Another descendent of the diesel electric locomotive can be found in the oil well drilling industry, Here, locomotive traction motors and. electric controls have been modified to fit the particular requirements of the drilling industry, One 2400 H.P. diesel electric drilling rig drilled a 24,000 Ft. well in West Texas with an electrical maintenance cost in the order of 7¢ per hour This was a new rig and the costs are less than the average maintenance costs will be for the life of the equipment, Even soy since it took one (1) year to drill this well, this 7¢ per hour has real significance. Electric shovels use a similar type of electrical equipment; they too have shown real savings over the equipment they replaced. Since electric drives have done so well, in other fields, they warrant consideration for use in high horsepower, large capacity trucks.

Jan 1, 1961

By Mahesh C. Jha

Cyanidation has established itself as the main process for extracting gold from ores in this century. However, many ores exhibit refractoriness to the conventional cyanidation process. The main cause of the refractoriness is generally the presence of carbon, tellurium, and sulfides, particularly those of antimony, arsenic, and iron. The problem is usually solved by either modifying the cyanidation conditions or providing an oxidation pretreatment. This paper presents results from studies that help in understanding the causes of refractoriness of various gold ores. This is followed by a discussion of many processes that have been developed to solve the problem such as intensive cyanidation, pressure cyanidation, carbon-in-leach cyanidation, and pretreatment processes such as roasting, chemical oxidation, autoclave oxidation, and bacterial oxidation.

Jan 1, 1986

By K. S. Olson

My reaction when first asked to present this paper was; "What could I possibly say that would hold the audience?s attention for 15 minutes? What could I offer that anyone familiar with the Nevada Barite Industry wouldn't already know?" Well, quite frankly I can't. The industry has certainly been anything but exciting for the past 10 years and, in fact, quite depressing. The challenge, for those few of us left in it, has been to keep it alive. At times it has felt like a doctor must feel with a terminally ill patient. All I can do is recap the past ten years, review the present state of the industry, and offer a few personal opinions and observations as to where I think we are headed.

Jan 1, 1993

By R. E. Mclvor

This is an update of an original dissertation on this topic by Lavallee, McIvor and Stolovitch (1992). A step-by-step, technical procedure used to measure and improve the performance of plant grinding circuits was adapted into a training program. ?Systematic Design of Instruction? was applied to: ? Determine if training was a suitable way to deliver this new technology; ? Define the technical content of the program; ? Select program specifications based on learner and context characteristics; ? Design, create and test prototypes of the training modules; and, ? Establish a process for plant implementation. The training program covers numerous skills that are extremely valuable for plant personnel, not only in the grinding area, but also for many other parts of the plant. This paper describes how new skills are brought into the workplace through designed instruction can be an effective alternative to hiring during severe skilled labor shortages.

Jan 1, 2008

By H. R. Hernandez-Guerrero, S. A. Robles-Salazar, M. Marín-Pasillas, P. J. Pompilla-Rosales

Peña Colorada is a company dedicated to the exploration, exploitation, and beneficiation of iron ore, serving the national steel industry. Established in 1975 as a stateowned enterprise, it transitioned to operating as a private organization in 1991. It is jointly owned by two investors, ArcelorMittal and Ternium, each holding a 50% stake. The mining operation is situated in the municipality of Minatitlan, in the northwestern part of the state of Colima, Mexico (Figure 1). It comprises an open pit mine and a concentrator, covering an area of approximately 2,300 hectares. The pellet mill is in the town of Manzanillo, Colima state, a port on the Pacific coast, about 46 km southwest of the mine. The pellet mill occupies its own property with a total area of 60.4 hectares. A gravity-driven concentrated slurry pipeline connects the mine and the pelletizing plant, located at an average elevation of 1,020 meters above sea level and 20 meters above sea level, respectively. Currently, Peña Colorada produces 4.1 million tons of pellets and 0.4 million tons of iron concentrate annually. In 2018, due to a change in the cutoff grade, the processing volume of the beneficiation plant increased from 9 million tons to 16 million tons annually. This led to a greater amount of information to process and characterize the ore extracted from the pit before its processing in the beneficiation plant. Consequently, Peña Colorada sought new ore control technologies to enhance ore selection, optimize human resources and data management, as well as minimize discrepancies between planning and execution. To ensure adherence to quality agreements with stakeholders, it is crucial to understand the ore characteristics before initiating mining activities.

Feb 1, 2024

By Augusto Andres Torres Toledo, João Felipe Coimbra Leite Costa, Luciano Nunes Capponi, Diego Machado Marques

Short-term mine planning to open pit requires defining diglines to orientate the excavation geometry. In deposits with multiple chemical variables, it is necessary to have more rigorous control over the feeding of the processing plant. This study analyzes the impact of incorporating multiple chemical variables, the risks generated by geological uncertainty, and the number and starting point locations of shovels in the sequential design of diglines. The objective is to maintain and preserve the low-grade variability, required tonnage, and continuity in sequentially selecting blocks. To achieve this, the probability distribution function of each chemical variable is used while attempting to maintain the ore grades as constant as possible. As it is difficult to maintain multiple elements with low variability simultaneously, the relevance of each chemical variable in the economic benefit is identified. Weights are assigned to signal the importance of each element based on its significance in the recovery process. Several diglines, consisting of sequential blocks, were generated on the same seed point to meet the weekly ore demand. Optimizing the stationarity of multiple chemical variables, accessing and reducing the geological uncertainty performed through geostatistical simulation of grades and transfers functions, considering the number and location of shovels, while meeting the operational restrictions of the selected blocks. The optimized digline with the multiple grades as stationary as possible is retained. The process is illustrated in a phosphate mine. The results show that the proposed method is viable and allows for a quick solution.

Jun 25, 2023

By John W. Stevenson, Ted L. Sartain

Underground booster fan installations are currently employed in hundreds of coal mines throughout the world. Such installations, when properly designed and maintained, have proven to be safe and effective tools to provide desirable airflow volumes on sections or in areas of mines where the ventilation requirements exceed the capacity of the main fan system. In cases where an airshaft cannot be justified due to surface topography, depth of cover, or limited reserves a booster fan can serve the same purpose, be operational in a fraction of the time and at a substantially reduced cost. Booster fans are currently non-existent in U.S. coal mines. This is primarily due to lack of acceptance by the Mine Safety and Health Administration (MSHA), which has failed to acknowledge the merits of a booster fan system. Also, the absence of booster fan provisions in Part 75 of the federal regulations has led to the misconception that booster fans are legally prohibited in U.S. coal mines. In 1986, Jim Walter Resources, Inc. (JWR) developed and submitted to MSHA a plan to install and operate an underground booster fan at the No. 7 Mine. Detailed computer simulations were used to substantiate JWR1s position, that the booster fan could effectively provide the needed airflow on a developing section without adversely affecting ventilation in other areas of the mine. JWR also realized that numerous safeguards and operating procedures were essential for providing a safe system. Thus, safety features such as electrical interlocking, independent power supply, remote atmospheric monitoring, etc., were incorporated into the plan. This paper is a case-study that discusses JWR's proposed plan to install and operate an underground booster fan at No. 7 Mine. Unfortunately, MSHA's continued negative response has prevented implementation of the plan.

Jan 1, 1989

By G. Kordosky, A. Feather, M. Virnig, P. Crane

Introduction The post World War II nuclear arms race and interest in nuclear power generation resulted in a significant demand for uranium in the 1950’s. This led to the development of uranium solvent extraction technology and uranium became the first metal to be recovered on a large scale by solvent extraction (SX) (1), interestingly more than 100 years after the extraction of uranium from an acid nitrate solution using diethyl ether was first reported by Peligot.(2) For a variety of reasons discussed elsewhere (3,4) there have been upheavals in the supply demand picture and price for uranium since the 1960’s. (Figure 1) The low price of uranium from the mid 1980’s until 2004 resulted in a depression of new resource exploration and mine development along with uranium mine / mill closures and decommissioning. People with skills in uranium processing could not find suitable employment and many experienced engineers and metallurgists took jobs elsewhere or retired. This resulted in a significant brain drain with respect to uranium processing technology.

Jan 1, 2007

By Lawrence K. Nordell

The selection of belt conveyor drive systems (*) is the subject of ongoing investigation. Frequently this choice has been governed by an incomplete perspective on the major considerations. A more comprehensive and objective approach is desirable. This paper presents additional factors which hopefully will broaden this perspective. BACKGROUND Conventional belt conveyors are powered by electric or electro-mechanical drives(*) mounted at the conveyor's head, tail, intermediate return span, or a combination of these (Fig. 1). A list of the drives reviewed is given in Table I. The following are main elements influencing the selection of the drive system: 1) dynamic characteristics, 2) economic factors such as capital cost, plant spares compatibility, reliability, availability, maintainability, and 3) environmental constraints. The principal dynamic characteristics of concern are the reactions of belt forces generated by the drive system during starting of the conveyor. Another attribute for consideration is the application of multiple driven pulleys used to 1) lower the conveyor's belt tension requirements, 2) increase the expected tonnage throughput, allowing for possible drive component failures, and 3) increase the plant spares flexibility related to the drive assembly.

Jan 1, 1977