Search Documents

Residential and commercial plumbers in the United States were introduced to Viega?s copper press technology in 1999. In short, the technology allows plumbers and installers to join copper pipe securely in four to seven seconds on pipe sizes of 1.2 to 10 cm (0.5 to 4 in.) by pressing the connections with specialized tools and fittings rather than through sodering or welding. The water- and air-tight technology, first introduced in Germany in 1989, includes three different sealing elements, a variety of materials and a selection of configurations. By eliminating the need to thread or solder pipe, connections and repairs can be made quickly and securely. Installations are also much quicker and as secure as traditional methods.

Jan 1, 2012

By Liguang Wang, Roe-Hoan Yoon

The thin film balance (TFB) technique was used to measure the equilibrium film thicknesses (H3 between two air bubbles in sodium dodecyl sulfate (SDS) and electrolyte (NaCl) solutions. The results were used to determine the magnitudes of the hydrophobic forces (K232) using the extended DLVO theory. The Km values determined from He measurement allowed us to predict disjoining pressure isotherms, which were found to be in excellent agreement with those obtained experimentally using a bike-wheel film holder. The rate of film thinning was measured at low SDS concentrations with varying amounts of electrolyte (NaCl) added. In general film thinning was controlled by the capillary pressure during the initial stages, while it was controlled by the surfaces forces during the later stages. At low NaCl concentrations, it was possible to predict the rate of film thinning using the Reynolds equation, provided that the driving force was corrected for the contributions from the hydrophobic force, which in turn were determined from the KZ32 values obtained from the He values measured experimentally. At high NaCl concentrations, where it was difficult to measure the equilibrium film thicknesses, the contributions from the hydrophobic forces were determined by fitting the film thinning data to the Reynolds equation. The K232 values obtained using both the equilibrium film thickness and the film thinning measurements showed that hydrophobic force deceased with increasing surfactant and salt concentrations. It was found that the hydrophobic force in foam films was very sensitive to the added electrolyte concentration.

Jan 1, 2005

By H. Huang, Y. Takasaki, R. N. Gow

"The presence of enargite (Cu3AsS4) is problematic in gold processing not only because it is environmentally hazardous due to its arsenic content but also because it is refractory, causing both cyanide and oxygen consumption to increase. Selective leaching and treatment of the arsenic would prove advantageous prior to applying conventional gold leaching methods. The reactivity of enargite samples from Butte in Montana and Quiruvilca in Peru were spectroelectrochemically studied under alkaline conditions – pH range of 8-13 – using Raman spectroscopy and cyclic voltammetry. Raman spectra of the surface were collected during and after potentially cycled voltammograms in order to determine and compare surface species against theoretical EH-pH diagrams constructed from mass-balanced thermodynamic calculations using STABCAL software. Under slightly oxidizing conditions, covellite (CuS) peaks were found in a short matter of time, above ~100mV vs. SHE for pH 9-13, suggesting arsenic leaching specifically occurred. At longer conditioning times, elemental sulfur was observed and tended to passivate the surface. The presence of elemental sulfur suggests that copper was eventually leached from the surface. By operating above pH 12, under slightly reducing conditions near -300mV vs. SHE, arsenic can be selectively leached as thioarsenate (AsS4 3-) or thiosulfate (AsO4 3-) without sulfur formation.IntroductionEnvironmental limitations on the pyrometallurgical processing of ores and concentrates bearing arsenic and other hazardous elements often outweigh those in hydrometallurgical processing, particularly when minerals like enargite (Cu3AsS4) are present. The hydrometallurgical processing of enargite-bearing materials can be broken down into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under alkaline conditions. The selective leaching of arsenic would preferably leave behind copperrich sulfide phases, typically chalcocite (Cu2S) and covellite (CuS), which then become more amenable to conventional copper (and gold) processing. Furthermore, selective leaching often employs sulfide (S2-), bisulfide (HS-) or polysulfides (Sx 2-) to first extract the arsenic as AsS4 3- and AsS3 3- (Delfini et al., 2003; Anderson and Twidwell, 2008; Tongamp et al., 2010a,b). However, hypochlorite leaching (Viñals et al., 2003; Curreli et al., 2005; Mihajlovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and finegrinding to mechanically activate the enargite surface (Balaz and Achimovicova, 2006) have been investigated to increase the normally slow reaction kinetics. Because gold ores are becoming more refractory due to increasing arsenic contents as a result of enargite, these methods are being examined more closely by the gold-mining industry."

Jan 1, 2015

By Alan A. Campoli

The US Bureau of Mines (USBM) conducted research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments. The goal is to minimize the over and under design of mine roof support, resulting in more productive and safer mines. To obtain the necessary data on roof behavior and support performance, USBM conducted several field studies. Each study covers roof geology, stress regime, ground reaction, support interaction and mining environment. A consistent experimental design is being used. This includes measurements of roof bolt loads and roof movements. So far, 10 studies have been conducted in several geologic settings.

Jan 1, 1996

By M. Deutsch, E. González, M. Williams

"Uncertainty exists in ultimate-pit limits due to geologic variation and unpredictable economic landscapes. In this work, we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis was used to model the effects of geologic and economic variations on ultimate-pit limits and overall project economics. This analysis was made possible by a new pit optimization implementation that can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate-pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement and to mitigate the possibility of incurring substantial costs to relocate critical mine facilities. Resumen ¦ Existen dudas sobre los límites del pit final por causa de la variación geológica y lo impredecible de los paisajes económicos. En este trabajo les mostramos como esta incertidumbre afecta el pit final y como puede ser analizada para mejorar el proceso de planificación de la mina. Se usó un marco estocástico con simulación geoestadística de análisis paramétrico con el fin de poder hace la modelación de los efectos de las variaciones geológicas y económicas en los límites de pit finales y proyectos económicos en general. Este análisis fue posible gracias a una nueva implementación de optimización de pits que puede ser automatizada y configurada para calcular pits finales para cientos de escenarios diferentes en cuestión de horas. La cuantificación temprana de la falta de certeza en pits finales durante el proceso de planificación permite a los ingenieros de minas tomar decisiones informadas en lo que respecta a la ubicación de infraestructura y en la mitigación de posibles costos sustanciales por causa de la reubicación de instalaciones clave de la mina."

Jan 1, 2015

By Raja V. Ramani, Wilson Miola

The potential health effects of quartz-bearing airborne dust in mine and mill atmospheres point to the need for the quantification of quartz content in the source material for determining the source-sink relationships and for choosing applicable control measures. While a standard method exists from a regulatory point of view for the sampling of coal mine atmospheres for determining (i) respirable dust concentrations and (i) the amount of quartz in thesamples, there is no generally accepted standard method for quartz analysis in bulk samples of coal and host rocks. Generally, the bulk sample is reduced to a powder for producing quartz analysis samples. Extensive controls are necessary to ensure representativeness of the analysis samples when these are very minute fractions of the bulk samples. Since the amount of analysis sample is not limited, alternative methods for quartz analysis may also be tried. It is, however, necessary to adopt a procedure which will satisfy several statistical requirements to guarantee representativeness of the quartz analysis samples. In this paper, the important factors in the preparation of quartz analysis samples from the host rocks and bulk samples are discussed. The method developed to prepare the analysis samples is outlined. The results of application of the procedures are presented. The procedure developed for quartz analysis sample preparation is based on sound statistical foundations. The procedure has been validated for reproducibility and homogeneity.

Jan 1, 1991

By Paul Schmidt, John Barber

This paper discusses the determination of cutoff grade (COG), including all revenue and cost factors and how to apply the COG in the world of engineering studies and mine planning for underground mines. It provides the engineer with important considerations and practical methods to establish COG and methods of using the COG in the work of mine planning, including the application of Mineable Stope Optimizer (MSO) software which is available on several 3D mine planning packages.

Feb 1, 2024

By R. A. Wharton, Z. Yang, R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al(III) and flotation collectors. It was found that the presence of Al(III) is necessary for good flotation of the organism, whether or not Pb(II) is present, when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8, and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al(III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminopropionic acid is used as collector, good flotation occurs at about pH 4 without the addition of Al(III).

Jan 1, 1992

By M. D. Flavel

Testing methods are described to help in decisions of selecting the most viable comminution circuits. The authors present a comparison evaluation based on numerous studies to help make initial choices for feasibility evaluations. An update summary of completed Bond grindability and Abrasion Index testwork at Allis-Chalmers Process Research Test Center for all materials is included. "What is the best circuit to comminute primary crusher product to make beneficiation feed?" This frequently asked question has the implication that there is one circuit which is universally the right circuit. The answer has been sought ever since it has been necessary to break rock to liberate entrapped mineral values. With every new contribution to the art and the science of comminution, the scope of the discussions broaden. It is not even possible to define what the abstract term best means.

Jan 1, 1981

By D. G. Abbott

This paper will describe the development, testing, performance evaluation, and in particular, the utilization for a mining application of revolutionary new mini-disc cutters for use in micro-tunneling and small-and medium-diameter tunneling or mining. It will begin by describing the engineering, testing, and development of rock cutting technology in conjunction with the Rock Boring Laboratories of the Colorado School of Mines. During initial tests, the five-inch cutters were able to penetrate limestone and welded tuff with compressive strengths of 9,000 psi to 24,000 psi. High excavation rates at low thrust and power were achieved with considerably less cutter wear than all previously available conventional discs. Eventually, the discs-with their modified carbide-insert cutting rings, high-load capacity bearings and cantilevered mountings-were able to facilitate the rapid and cost-effective installation of micro-and small-diameter pipes and tunnels in large cobbles and even solid rock, with compressive strengths exceeding 30,000 psi. This paper will also discuss the further development of the machine's cutter head and discs to full-scale site use on a range of tunnel machine sizes and soil conditions, including rock, boulders, and soft ground. Potential mining applications include the installation of tunnels to pro-vide ventilation, emergency escape routes, water drainage, compressed air, electricity, and sand-fill.

Jan 1, 1996

By Robert J. Collins

Computer-aided design drafting systems have been employed in plant design for nearly ten years. Current and future systems will include computer-aided engineering as well. This paper will explore the history and development of such systems including computer and workstation hardware, graphics software, and plant design applications software. The paper will also address future systems and will present both the system vendor and the mine mill designer's view. Specific examples of particularly successful applications will be included.

Jan 1, 1985

By H. R. Quina

Phosphate is one of the most important minerals in our world today. It contains the life-giving element of phosphorus, which is essential to the growth of every living cell in plant, animal, and man. This vital mineral is found in twenty-three states of the United States; however, for more than 70 years, Florida has led the nation in phosphate-production and now produces 70% of the requirements of this country. Since the early 1880% when rich phosphate deposits were accidentally discovered in a river-bed in Central Florida, the industry has developed into a multi-million-dollar operation. Phosphate mining began in Florida in 1887 with very crude methods and equipment. The original process was necessarily slow and tedious, resulting in total production of 3000 tons in 1888. Progress was made in improved mining operations, and by 1894. Florida had grabbed the lead as the nation?s largest phosphate-producing area, and is still in the top position.

Jan 1, 1962

By H. W. Renner

The paper industry is an $80 billion/year business that is the largest consumer of industrial minerals. Paper industry generally refers to paper and paperboard products, including pulp mills. Grades and uses of paper and paperboard are very diverse, including such things as napkins, paper plates, corrugated boxes, magazines, newsprint, currency, and copier paper. Only about 40% of paper utilizes industrial minerals as fillers or coating materials. Minerals are used for both functional and economic reasons. Most often, minerals such as kaolin clay and calcium carbonate are used to improve print quality, brightness and opacity of paper. The minerals can be added as fillers into the paper in the wet end of the papermaking system, or can be applied as part of a coating to the paper. Coated papers are the highest quality paper, being used for magazines, advertising brochures and annual reports. Common uses for filled uncoated paper are books, copier paper, envelopes and many of the Sunday newspaper advertising inserts.

Jan 1, 1993

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

To solve the problem of time-consuming and low precision in updating the open-pit vehicle transportation network, a high precision road network model construction method for unmanned vehicles in open-pit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3 + C (DeepLabv3 + Concat) is presented. Then, the road information extracted by the DeepLabv3 + C network is used to construct a three-dimensional model of the open-pit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicle meeting in open-pit mines, a vehicle meeting strategy was proposed. This strategy is used to guide the navigation of unmanned vehicles in open-pit mines. Besides, the DeepLabv3 + C network is verified by comparing the mIOU (means Intersection Over Union), accuracy, and continuity of road image extraction with the mainstream networks. The road network model constructed in the first step is quantitatively analyzed, and its performance is compared with GPS trajectory clustering methods. At the end of the paper, vehicle running simulation is carried out on the road network model by using Unity (a 3D visualization simulation software). The results show that the road network model constructed by this method can meet the navigation requirements of unmanned vehicles in open-pit mines, and the feasibility of the vehicle meeting strategy is proved.

Jan 11, 2022

By C. Treworgy

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Jan 1, 1997

By R. S. Conti, M. R. Krump, C. P. Lazzara Ph. D., R. L. Derick, L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, CO, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward-sloping (20%) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward-sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used, due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results.

Jan 1, 2010

By R. J. Hickson

The Grasberg copper-gold deposit was discovered in Spring 1988, just one year prior to the planned closure of Freeport Indonesia's original Ertsberg open pit copper mine. In spite of Grasberg's remote location, 600m above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought their latest open pit mine into production in the last week of 1989, less than two years after discovery. This paper describes the start-up of the operation, highlighting synergies drawn from both the original Ertsberg experiences and the current Freeport Indonesia underground mines.

Jan 1, 1991

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

By J. W. Mausteller

Chemical oxygen supplies have been used for nearly 60 years, with their greatest application during the last 25 years. They are of two types, the superoxides and chlorate "candles", The superoxides are demand chemicals, responding to the needs of the user and to supply oxygen and remove carbon dioxide. Chlorate candles are formed solid element which furnish oxygen only and do not remove carbon dioxide. Properties of these materials will be described, with comments on the respiratory requirements of a man under various workloads, types of equipment which use chemical oxygen, comparison with other systems and potential application to an underground mine survival system.

Jan 1, 1971

By J. M. Wempen

Booster fans in underground coal mines are often located using the concept of a neutral point. Normally, intake airways are maintained at higher absolute pressure than return airways; therefore, air leaks from intake to return. By adding a significant pressure force to a region of a ventilation system, booster fans installed in a return airway can increase the pressure in the return so that air leaks from return to intake. This is commonly referred to as recirculation. The neutral point occurs at the location in the system where the pressure difference between [ ] the intake and the return airway is zero. At this point, there is no leakage or recirculation. Ideally, placing a booster fan near the neutral point minimizes leakage and recirculation. However, in practice, the position of the neutral point is not static and it changes as the ventilation system parameters change. Booster fans have the potential to increase the capacity and efficiency of coal mine ventilation systems. However, these fans add a significant pressure source to ventilation systems and can create areas where the pressure in the intake is less than the pressure in the return causing recirculation. In systems with multiple booster fans, there may be multiple recirculation paths and, as the capacity of these fans increases, recirculation is more likely to occur.

Jan 1, 2012