Search Documents

By Carlos Viramontes Aldana

Mining in Mexico is one of its post traditional activities, whose influence in the development of important cities and communications has been decisive. Precious metals and, to some extent, copper and tin were known and used before the Colonial period, but from the sixteenth century to tie end of the nineteenth century, mining and metallurgical industries were concentrated in the precious metals, mainly silver. This silver was exported to Spain and other countries under the Spanish. Rule, Mexican peso was known world wide since the end of the sixteenth century and Mexico ranked as the first silver producer since the eighteenth century.

Jan 1, 1985

By Fikret Suner

Two rare evaporite minerals, nahcolite (NaHC03) and trona (Na2C03?NaHC03?2H20), are both widely used in the production of sodium carbonate (Na2CO3) The largest natural carbonate deposits (trona) are in Wyoming, USA, the second largest deposits are in Turkey, in a lacustrine basin (Beypazari) where nahcolite and trona are located within the Miocene Hirka Formation. The Hirka Formation is mainly composed of bituminous shale, claystone, marlstone, tuffltuffite, and dolomitic limestones. Although numerous trona beds are interbedded within the above mentioned sedimentary units, there are only two beds of trona that are of economic interest. The lower part of the lower trona bed is rich in double carbonates such as pirrsonite (NA2C03? CaC03?2H20) and gaylussite (Na2C03?CaC03?5H20), indicating a change in Ca/Na ratio in the solutions which are responsible for the formation of soda occurrences. In contrast, the upper part of the upper trona bed is rich in nahcolite. This minerological pattern has been found in every drill- hole in the basin. While both trona beds average up to 10 m (33 ft) thick, the average thickness of nahcolite is approximately 0.5 m (1.6 ft). Also, thin section studies show that many fibrous and lath-like trona crystals contain small radial nahcolite crystals; all of them are euhedral and equi-dimensional. Geochemical studies of major, minor, and trace element contents also support this coexistence. Macroscopic and microscopic observations reveal that the nahcolites principally were formed as a result of an incongruent dissolution process of trona. In conclusion, the presence of nahcolite in the Beypazari basin is due to the dissolution process of trona, particularly during the last stage of evaporation, as a result of fresh water entering the basin. During that time, an increase in the HC03/ C03 ratio resulted in nahcolite-trona phase transitions.

Jan 1, 2001

By T. V. Falkie

REMARKS OF DR. THOMAS V. FALKIE, DIRECTOR, BUREAU OF MINES, U.S. DEPARTMENT OF THE INTERIOR, BEFORE THE FALL MEETING OF THE SOCIETY OF MINING ENGINEERS, AIME, ACAPULCO, MEXICO, SEPTEMBER 23, 1974 This is a time of uncertainty on the world mineral scene. For some of the world's so-called "developed" countries, reserves and production of key minerals are running low. And, we have learned that the energy so essential in recovering and processing minerals can suddenly be in short supply. The prospects for a "no growth" situation in energy or mineral consumption are practically nil. Moreover, the world's economy is in flux, casting doubt on whether traditional mineral customers will continue to be able to buy, or for that matter, whether traditional suppliers of minerals will continue to sell. It is clear that the mineral situation is contributing to world inflationary pressures, which incidentally are most damaging to developing countries. So it is appropriate that SME members devote this session to the world mineral situation, and consider some of the opportunities and responsibilities that we will inevitably encounter as the future becomes the present. The opportunities, to me at least, are especially intriguing, I have the good fortune to be part of an organization that has an enormous capability and responsibility for dealing with mineral problems. The Interior Department's Bureaus, including the Bureau of Mines, have been around for a long time. They are. a prolific and reliable source of both mineral information and mineral technology.

Jan 1, 1974

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixer units. However, recent experience in both large and small plants has shown this not to be the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers, which both lead to reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Changes to the method of specification and selection of primary and secondary mixers have been made to eliminate the onset of partial separation during operation. The observation of settler operation has shown that it is also a dynamic process, even under "steady-state" conditions. Four transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze and erratic and high entrainment levels in the discharges. A, first approximation analysis has shown that there are significant pressure differentials within settlers, and these change along the length and with the phase separation rates. A technique to control the effects of these transients was developed that allows plant performance to be improved beyond "standard" expectations. The design and selection of the settler internals is described. Key words: Solvent extraction, Mixer-settlers, Phase separation, Entrainment, Mixer transients

Jan 1, 2003

By Jerry Grott

Southwest Salt Company is solution mining the Luke Salt Body of probable late Miocene age. The discovery hole, from which the first core was recovered, was drilled in 1968. The deposit was encountered at a depth of 880 feet, and the bit was still in salt at the bottom-hole depth of 4,500 feet. The solar ponds, developed on land formerly dedicated to agriculture, have an annual capacity of about 90,000 tons. Because land values are very high, mining rates and procedures are governed by the need for near-saturated brine to minimize land requirements. Because of the frequency of dust storms, the salt operation uses a unique wet-harvesting method. Most inventory is kept in the ponds under brine and harvested only a few days before shipment. Studies of the nature of crystal growth and the distribution of windblown and brine impurities led to the development of procedures for processing salt of high chemical purity and low insolubles content. Chemical purity exceeds that of most salt produced in fuel-fired evaporators. Salt is shipped from Phoenix as tar east as west Texas and as far west as central California. Occasional shipments have been made to Hawaii and Alaska.

Jan 1, 1987

By G. H. Kuhnhausen

The Bear Creek Uranium Mill was designed in 1975 to process 909 tonnes per day (1000 STPD) of low-grade uranium ore from the Powder River Basin in Wyoming. The mill was expanded to 1818 tonnes per day (2000 STPD) in 1979. The Bear Creek Uranium Project is owned by the Bear Creek Uranium Company, a partnership of Rocky Mountain Energy Company and Mono Power Company. The original mill design contemplated processing ores from Bear Creek Uranium Company properties exclusively. The expanded capacity has been utilized for tolling ores from Kerr McGee Nuclear Corp. and other mining companies in the region. This paper describes the process of designing the original mill, the lessons learned from operation, and the design of the process modifications required for expansion. The project background, design philosophy, design basis, design criteria, actual flowsheet, special design considerations, and a comparison of assumed operating conditions and actual operating results will be presented. Bear Creek Uranium Company wishes to thank and acknowledge the help granted by the many operating companies who provided invaluable information, insight, and critique of the Bear Creek design through all the various stages and were instrumental in the successful completion and start-up of the mill. Without their contributions, the design philosophy used at Bear Creek would not have been possible and the results obtained would surely have been less satisfactory.

Jan 1, 1979

By S. Gallagher, A. Mayton

Introduction The mining industry has long been associated with a high incidence of low back disorders and pain (Klein et al. 1984, Leigh and Sheetz 1989, Brinckmann et al. 1998). It is believed that the higher incidence of these injuries among miners is the result of high exposures to postural demands, heavy manual work, and exposure to whole-body vibration (WBV). Recent work has indicated that miners involved with heavy lifting (especially in restricted spaces or on uneven ground) or who have been exposed to whole-body vibration in undamped seats experience noticeable changes in their spines that are consistent with degeneration of the intervetebral discs of the spine (Brinckmann et al. 1998). As will be described shortly, there is mounting evidence that disc degeneration plays a large role in the development of low back pain, particularly chronic back pain. Until fairly recently, medical doctors generally assumed that back pain was the result of muscle strain, ligament pain, or so-called “trigger points” (Bogduk, 1997). However, research supporting these mechanisms of pain has been very scant. When subjected to scientific scrutiny, none of these mechanisms has been shown to relate to back pain in a convincing manner. On the other hand, there are three mechanisms that have been shown to be highly associated with back pain in controlled scientific studies: sacroiliac pain (present in 13% of back pain sufferers) (Maigne et al. 1996), facet joint pain (present in 15 % of back pain sufferers) (Schwarzer et al 1994), and disc disruption and degeneration (present in 39% of chronic back pain sufferers) (Moneta et al. 1994). The latter mechanism, which bears the highest relationship to back pain that has been objectively demonstrated, will be the focus of this section. Scientists now believe they have a good idea how back pain may develop in cases involving disc disruption and degeneration (Bogduk 1997). As the spine experiences loading during lifting tasks or whole body vibration, the first structure to fail is called the vertebral endplate, which is a structure that attaches the disc of the spine to the vertebral body (Figure 1). The endplate typically experiences a fracture, which the body will attempt to heal by means of scar tissue. Unfortunately, this scar tissue impedes the flow of nutrition to the disc itself (discs are dependent on nutrition from the vertebral bones), and if the supply is reduced sufficiently, the disc will start to degenerate. As this degeneration process proceeds, fissures or tears in the fibers of the disc start to develop. If any of these tears is a grade 3 fissure (Figure 2), an inflammatory response occurs in the disc, which will lead to the well-known sensation of low back pain (Peng 2006).

Jan 1, 2007

By Barnaby J. Watten, Sibrell. Philip L., Brian J. Vinci, Andrew E. Friedrich

We evaluated a new process for remediation of acid rock drainage (ARD). The process treats ARD with intermittently fluidized beds of granular limestone maintained within a continuous flow reactor pressurized with CO2. Tests were performed over a thirty day period at the Toby Creek mine drainage treatment plant, Elk County, Pennsylvania in cooperation with the Pennsylvania Department of Environmental Protection. Equipment performance was established at operating pressures of 0,34,82, and 117 kPa using an ARD flow of 227 L/min. The ARD had the following characteristics: pH, 3.1; temperature, 10 OC; dissolved oxygen, 6.4 mg/L; acidity, 260 mg/5; total iron, 21 mg/L; aluminum, 22 mg/L; manganese, 7.5 mg/L; and conductivity, 1400 uS/cm. In all cases tested, processed ARD was net alkaline with mean pH and alkalinities of 6.7 and 59 mg/L at a CO2 pressure of 0 kPa, 6.6 and 158 mg/L at 34 kPa, 7.4 and 240 mg/L at 82 kPa, and 7.4 and 290 mg/L at 117 kPa Processed ARD alkalinities were correlated to the settled bed depth (p<0.001) and CO2 pressure (p<0.001). Iron, aluminum, and manganese removal efficiencies of 96%, 99%, and 5%, respectively, were achieved with filtration following treatment. No indications of metal hydroxide precipitation or armoring of the limestone were observed. The surplus alkalinity established at 82 kPa was successful in treating an equivalent of 1136 L/min (fivefold dilution) of the combined three ARD streams entering the Toby Creek Plant. This side-stream capability provides savings in treatment unit scale as well as flexibility in treatment effect. The capability of the system to handle higher influent acidity was tested by elevating the acidity to 5000 mg/L with sulfuric acid. Net alkaline effluent was produced, indicating applicability of the process to highly acidic ARD.

Jan 1, 2000

By M. Wasel

The Gross Rosebel gold deposits are located in theGuiana Shield of northcentral Suriname in South America. The property lies 80 km (50 miles) south of the capital city of Paramaribo. Gross Rosebel covers 170 km2 (65 sq miles) in an area of small hills covered primarily with secondary tropical rain forest, separated by discontinuous savannah (Fig. 1). The concession is accessible from Paramaribo by a 120-km (75-mile) paved and all-weather gravel road. Surficial gold was discovered in 1880 by local artisanal miners. This was followed by small-scale mechanized mining from 1885 to 1939. Placer Development carried out the first systematic exploration program from 1974 to 1977. In May 1992, Golden Star Resources optioned the property. Initial shallow reconnaissance diamond drilling of the extensive surface geochemical anomalies intersected sporadic gold mineralization with no apparent continuity between drill sections. Successive deep augering, trenching and systematic grid drilling, based on information from surface mapping, allowed the development of a preliminary geological model. Further drilling of specific structural-lithologic targets and more complete synthesis of geological data from the trenching and deep auger sampling added to the geological model and defined the multiple controls of gold mineralization. Carefully planned infill drilling on a tighter grid spacing resulted in progressive definition of reserves within six discrete gold deposits. Reserves based on $11.25/g ($350/oz) gold now stand at 35.5 Mt (39.1 million st) of 1.8 g/t (0.053 oz/st) gold, or 62.2 t (2 million oz) of gold.

Jan 1, 1998

By F. Habashi

Brazil is a major mineral and metal producer, has magnificent fauna and flora, and superb architecture. In 1693 gold was discovered in Ouro Preto and Brazil produced about half of the world&apos;s gold. In 1726 diamond was discovered in the region of Tijuco in the Province of Minas Gerais, 150 km east of Bello Horizonte. The country became independence from Portugal in 1822 as the Brazilian Empire. In 1876, an Englishman succeeded in obtaining from the Amazon region seeds of rubber trees and secretly transferred them to England, where they were planted in the royal gardens at Kew. Some of the seedlings which spouted were sent to Ceylon and Singapore. Thus, began the rubber industry in the East. Today, Brazil is the largest producer of niobium, and produces a large number of other metals. The Mineral Research Center in Rio de Janeiro is the countries main Government establishment for mineral research. The country has been a republic since 1889 with its capital in Brazilia.

Jan 1, 2009

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Cheng, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates have wide application in global smelting operations, comprising primarily of chalcopyrite (CuFeS2) as the principal mineral, accompanied by chalcocite (Cu2S) and bornite (Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates frequently harbor detrimental impurities, notably fluorine ions, which can cause various complications during the smelting process. Moreover, an elevated fluorine content in copper concentrates may entail financial penalties and sales constraints. This review conducts a comprehensive analysis of existing methods for the removal of fluorine, presenting a nuanced assessment of their merits and demerits. It also provides valuable insights into the current landscape of fluorine elimination from copper concentrates and pinpoints pivotal areas warranting future investigation. This review endeavors to serve as a pragmatic resource for researchers and industry professionals operating within this domain.

Jan 1, 2024

By A. E. Ketler

Optical smoke monitoring fills an important gap in ventilation and fire safety: namely monitoring of smoky, low temperature fires where little CO and heat are generated. Smoke monitoring also avoids the nuisance alarms due to diesel exhaust, battery chargers, blasting and welding. The smoke optical density (OD) fire alarm standard specified by MSHA presents an opportunity for improved safety. Experience of actual mine usage of the SmokeBoss*100 is reviewed, with particular regard to effectivity, maintenance and cost.

Jan 1, 1995

By Jim Britton

Sustained elevated metal and coal prices in 2011 continued to drive mining projects across British Columbia. The province is the top producer of copper, exporter of coal and the only producer of molybdenum in Canada. The province also produces significant amounts of gold, silver, lead and zinc and more than 30 industrial minerals. The total 2011 value of solid metal production is an estimated $8.6 billion and the outlook for 2012 is positive. British Columbia is poised to bring several new mines onstream in the next few years. Construction continues at the New Afton and Mt Milligan copper-gold projects that are anticipated to be open in 2012 and 2013, respectively. The provincial Environmental Assessment Office indicates there are 26 mine proposals in process with three currently under review and 23 in the preapplication stage. The following text briefly describes 2011 metal and coal mining activities in the five regions reported on by the provinces? regional geologists (Fig. 1).

Jan 1, 2012

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By James H. Barks

Exploration for ore deposits in southeastern Missouri in the 1950&apos;s resulted in the important discovery of lead, zinc, copper and silver in 1955. Further discoveries in the area led to the naming of the Viburnum trend. It has sometimes been referred to as the "New Lead belt" to distinguish it from older lead-producing areas to the east. As presently developed, the "trend" is 35 miles long, running north and south about 50 miles west of the Lead belt. Galena (lead) is the principal ore mined, with lesser quantities of sphalerite (zinc), chalcopyrite (copper) and silver recovered as economic by-products. The ore body is as much as 140 feet thick and 1,200 feet wide, and is found in the Bonneterre Dolomite (Upper Cambrian) at depths ranging from 700 to 1,200 feet. Since its discovery many companies have engaged in exploration and several major companies have developed new mines and constructed mills and a smelter in the area. The first mine in the Viburnum trend came on stream in 1960, but as more mines came on stream and others reached capacity, lead production increased to the point that the Southeast Missouri Lead district produced 432,576 tons of lead in 1970 to become the world&apos;s largest lead-producing region (Missouri Geological Survey and Water Resources, 1971). The Viburnum trend area with its rolling, heavily forested hills and numerous clear running streams is in the Clark National Forest of the Missouri Ozarks. Until the recent development of its mineral resources, the area was sparsely populated and nearly unmarked by the activities of man. Industrial development is almost certain to be accompanied by environmental changes. In a day of growing awareness of the need to preserve the quality of the

Jan 1, 1971

By R. B. Berg

Montana sapphires were first discovered in alluvial deposits in the Helena area in 1865 and subsequently were discovered in other alluvial deposits in southwestern Montana and also in a lamprophyre dike at Yogo in central Montana. From about 1900 until the late 1930?s, when synthetic sapphire began to come into widespread industrial use, Montana sapphire mines produced large quantities mainly for watch bearings with lesser production for the gemstone market. The Yogo deposit is now mined for the gemstone market and two of the alluvial deposits are mined to produce sapphires for the fee-sieving of sapphire-bearing gravel and for the direct sale of gemstones. The generally pale-colored sapphires from the alluvial deposits in southwestern Montana are heated to enhance their colors whereas the generally blue sapphires from the Yogo deposit require no treatment. Markets for sapphires from both the alluvial deposits and the Yogo deposit are strong. In spite of reported historic production in excess of 70 tonnes, mineable resources appear to remain at most major deposits. Also abundant untested lamprophyre dikes in central Montana may host sapphires similar to those at the Yogo deposit.

Jan 1, 2009

By B. Anameric, S. Kawatra

Pig iron nuggets, which have similar chemical and physical properties with blast furnace pig iron, were produced by a single step heat treatment of self reducing – fluxing dried greenballs. During this single step heat treatment the transformation of self reducing fluxing dried greenballs into pig iron nuggets did not take place instantaneously. Rather, it was composed of three transformation stages, (1) transformation of self reducing – fluxing dried greenballs into direct reduced iron (DRI), (2) transformation of DRI into transition direct reduced iron (TDRI), and (3) transformation of TDRI into pig iron nuggets. Thus, the objective of this research was to investigate these transformation mechanisms by analyzing the transformation stage products. The transformation stage products were produced at a constant furnace temperature of 1425°C and various furnace residence times. They were characterized according to their microstructure, microhardness and apparent density. The changes in the product’s physical and chemical properties with furnace residence time were utilized in understanding the transformation behavior, the chemical events that took place and the controlling mechanisms. It was determined that the transformations were dictated by the changes in the slag viscosity and wetting properties, and by carbon diffusion into metallized areas.

Jan 1, 2007

By A. J. Richins, M. G. Nelson, R. Dunne

From the inception of flotation in the late 1800s, coarse particle recovery has been a challenge to practitioners. By the early 1900s, flotation processes included oil flotation, skin flotation, agglomeration flotation, and froth flotation, and for each there was a proliferation of flotation equipment. Ensuring good coarse particle recovery included desliming of the feed and proper conditioning were required. Froth flotation was at first used mainly to treat finer materials from grinding circuits. The maximum size for coarse particles was from 3.18 to 4.78 mm. In froth flotation, large particles with high specific gravity tend not to be recovered. Coal and minerals of low specific gravity and flaky minerals such as graphite, mica, and talc can be floated in larger sizes. In the early 1960s, the phosphate industry began using column cells to recover coarse particle by froth flotation, but early columns suffered from poor bubble generation and sanding at the flat base of the column. Recently, improved coarse particle recovery has been the object of new cell designs—the Eriez HydroFloat™, the Jord NovaCell™, the FLS coarseAir™ cell, and the Cidra P29 integrated system. The paper will follow the development of coarse particle flotation with a focus on the development, laboratory assessment, and operation of the new flotation equipment and technology designed to recover coarse particles.

Feb 22, 2026

By Reynold Q. Shotts

Underground mines, penetrating well below the water table, quickly fill with water when abandoned. Ordinarily, these natural cisterns are not thought of as sources of industrial water. Under special circumstance, if chemically treatable, they might become valuable industrial water reservoirs. An example of a group of about 20 mines in a geological and structural setting insuring water entrapment, rapid recharge and a possible minimum of contamination, are the small, compact Belle Ellen and Piper basins in Alabama&apos;s small but second most productive coalfield, the Cahaba. The mines have been abandoned from more than 50 to less than three years. The county now produces about a million tons of coal annually, all from strip mining. Figure 1 shows an idealized cross section of the strata in the Belle Ellen syncline near West Blocton, Bibb County, Alabama. Figure 2, 3 and 4 are maps showing the location of the syncline, other structural features, the outcrop lines of the three principal coalbeds underlying the basin, and the mined-out areas on the three beds (1).

Jan 1, 1973