Search Documents

By Phil Dakin, Rajiv Chandramohan, John Lo Grande, Greg Lane

Crushing and grinding circuit availability is a critical design factor defining the installed equipment selection and the process buffers required to maintain throughput during maintenance. The comminution circuit typically accounts for a process plant’s largest capital expenditure and energy use. Effective process and equipment selection and layout optimization are crucial steps when combining the objectives of cost-effective design and high circuit availability in operation. This paper outlines fit-for-purpose design principles for optimizing process flow, eliminating standby equipment and reducing buffer residence time whilst improving maintainability and operability.

Feb 1, 2025

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991

By Robert J. Timko, R. Lincoln Derick

The Bureau of Mines evaluated the integrity of escapeways in a three entry underground coal mine. A center conveyor belt entry (secondary escapeway), was flanked by an intake (primary escapeway) and a return entry. Diesel equipment was used throughout the mine for material and personnel haulage. A carbon monoxide monitoring system, tied to a data recording computer on the surface, was deployed throughout the belt entry and at selected sites in the intake and return entries. Previously, the company had a fire of unknown origin in another mine, which prompted an interest in the performance of their escapeways. An initial, qua1itative evaluation was performed by burning approximately 14 kg of coal at the mouth of the intake entry. The first test was followed by a similar burn at the mouth of the belt entry. These initial trials showed a high quantity of leakage between entries. In several follow-up evaluations, simulated fires, using a tracer gas, were set in the intake and belt entries. Tracer gas concentrations were obtained in all entries at four different underground locations. The results of these tests showed that permanent stoppings could not guarantee isolated, contaminant-free escapeways.

Jan 1, 1989

By V. E. Gall, A. Vonthron, J. Ninic, A. Marwan, M. König, G. Meschke, A. Alsahly

"In current tunneling practice, finite element simulations have become an integral element of the planning and design process. These models are most often manually generated using 2D CAD drawings, which is a laborious and time consuming process. In this paper, we propose a BIM based approach, in which the 3D FE-model is automatically generated through a set of compatible geometries of individual components, i.e. the geology, alignment, lining and the TBM. The BIM model also includes all relevant model parameters of the tunneling project that can then be incorporated into subsequent analysis to be performed during the tunnel drive. The setup and the execution of the FE-analysis are performed automatically utilizing all required data from BIM. The applicability and efficiency of the proposed strategies is demonstrated by means of project data from the Wehrhahn-line metro project in Düsseldorf, Germany. Both the design as well as the construction stage is considered. INTRODUCTIONIt is recommend to employ Finite Element (FE) simulations in order to ensure a high degree of safety and quality for any given project (Guglielmetti et al. 2012). As such, FE models form an integral part in the design and planning stages of modern tunneling projects. These models are often time consuming to construct and require data from many different sources. This data is most often not centrally stored and therefore not easily accessible. Additionally, the formats in which project data are stored are typically not compatible with the formats required by an FE program. This is especially true in the case of geometrical data, such as CAD drawings. Although existing design drawings are most often used as the basis for a FE model, a direct import into a FE program is most often not successful as the imported data generates a geometry that does not fulfill the requirements of a FEM model, such as model connectivity. Even if a geometry is successfully imported, other necessary aspects of an FE model, such as boundary conditions and material properties, must be applied manually. These incompatibilities inevitably result in the creation of a new model, which, especially in the case of complex 3D models, is a time consuming process."

Jan 1, 2016

By T. C. Vogt

The past history of uranium production has been dominated by strip and shaft mining methods, but recently in-situ leaching has emerged as a viable alternative for uranium recovery. (1-8) Mobil was the first company to start in-situ uranium leaching in New Mexico. Mobil's Crownpoint project areas are in Mdinley County and are part of the Grants Mineral Belt. The major uranium deposits in this area occur in the Westwater Canyon Member of the Jurassic Morrison Formation. (9-11) The ore depth at the Crownpoint project is about 2000 ft. In an earlier paper we discussed the uranium mineralogy of an areally broad sampling of Crown- point ore. (12) The organic carbonaceous material often associated with the coffinite ore was characterized in some detail. The organic material appeared to be a very mature, coaly-type kerogen derived from plant components. This result was consistent with other studies on such carbonaceous material. (13-15)

Jan 1, 1981

By Jean Rainville

Gold was first discovered in the central region of French Guiana in the mid 1860's. Production was based strictly from placer mining of the various rivers in the region. At the moment, a number of companies are actively engaged in hard rock gold exploration, concentrated in the northern and central regions of the country. The Franc-Or/BRGM joint venture in the Sophie-Repentir region of Central French Guiana offers an exceptional opportu­nity for the discovery of one or more million-plus ounce deposits of gold owing to a highly favorable structural setting in Precam­brian greenstones that host several known vein gold occurrences, some of which appear to occur near the border of a potassic granitoid intrusion. At this point in time, based mostly on predecessors' work, mineable reserves could be estimated to be in the 500,000 ounces range over the length of the property. The exploration campaign under way has the objective to delineate probable reserves of at least 2 million ounces that could be mined by open pit mining methods in the area. The program should be completed in the next 18-24 months. In order to efficiently and effectively evaluate this very large property area, all of the necessary camp, mechanical and drilling equipment has been purchased and is being transported to the property. Most of that equipment was purchased in Canada. The first drill target is the Repentir sector because of its access and the amount of detailed work that has been done by BRGM on that concession, but geological evidence suggests that many areas on the property could offer even more potential.

Jan 1, 1995

By W. F. McDermott

The Iron Ore Industry has perhaps seen more varied and drastic changes in its approach to crushing and grinding in the last 5 years than any of the other mineral industries, Multimillion ton per year plants have become common place. Centralized control and computers have become an established benefit. Autogenous grinding along with a variety of rod and ball grinding flowsheets are in use. This morning I will discuss a few of the more important and new concepts in the control of these crushing and grinding circuits.

Jan 1, 1970

As we are all well aware, the demand for coal is increasing very rapidly. This makes the coal industry one of great opportunity for both the miner and the-supplier. Up until the middle 1960's, the price of coal had been one of the most stable of all commodities for the proceeding fifty years. In somewhat oversimplified terms this was because the inflationary tendencies had been offset by improved mine techniques and more efficient, more productive, and more reliable equipment; but, in the last seven years the price of coal has doubled. It is not the intent of this paper to discuss the many reasons for this price increase, but to show how the cost of hauling coal can be sharply decreased with a new truck concept. Not long ago a mining executive stated that all haulage trucks now available are basically the same. They look the same; they cost about the same; they have the same engine, power train, and tires; and, they have about the same operating cost. Truck size has increased which has reduced the number of drivers, but the purchase price and maintenance and repair costs have increased proportionally. Pits must be widened and loading shovels enlarged, out, all this has not reduced the cost of moving coal. Another executive said that he saw no advantage in buying new trucks because his people now know how to maintain and operate the ones they presently have. They have all the right spare parts along with a good maintenance program. Most replaceable parts of the trucks now in operation have been replaced and improved at least once and the trucks are now running better than when they were new. Besides, the trucks are no pretty well written off.

Jan 1, 1972

By J. T. Hollow

The Fort Knox Mine is located in Alaska?s interior, where the average ambient air temperatures range from -24°C (-11°F) in January to 16°C (61°F) in July. The mill processes a free-milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leaching, carbon adsorption and cyanide destruction kinetics. Additionally, an energy-balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy-balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy-balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post-project plant performance that validates the model and shows that the mine produced an additional 596 kg (19,155 oz) of gold while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By Peter A. Gillett, Ian S. Clelland, J. G. S. Hynd

Today mine shaft and slope contracts include a greater amount of ancillary work such as level and pump stations, loading pockets, rotary and side dumps and connecting raises. This ancillary work requires the application of a number of construction methods often for short periods and often at short notice if the contractor is to maintain a profitable operation. In the next decade, the number of shafts that will be sunk by a boring method will outnumber those sunk by traditional methods. This will be particularly true of the deeper shafts where water problems are minimal. The increase of bored shaft work will not decrease the work completed by the shaft sinking contractor but it will change it. A greater emphasis will be placed on the speed of construction of station and other ancillary work. To meet this challenge the contractor requires full information on the ancillary work as well as the shaft work at an early date, preferably pre-bid. The two examples discussed in this paper illustrate the importance of early information. The two main factors of shaft ancillary work construction are sequence and ground support. This paper describes two examples completed recently by The Cementation Company of America Incorporated in Arizona. The first described is a Rotary Dump-Ore Pocket-Ore Pass complex and the second described is the excavation of the Main Station Level in a 2 Station-Loading Pocket-Ore Pass complex. CONSTRUCTION OF ROTARY DUMP, ORE POCKET AND PASS Introductory

Jan 1, 1976

By R. V. Ramani, K. V. Raj, S. Bandopadhyay

The air flow problems in openpit mines are complex. Computational fluid dynamics (CFD) models can provide detailed information regarding air flow pattern, velocity distribution, temperature, and pollutant concentration in an enclosed domain of an openpit mine. A range of turbulent models can be selected with varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithms they use. As a result, predictions vary from model to model. This paper presents a study of pollutant transport in an actual openpit mine under a stable boundary layer. The objective was to test two turbulence models using similar geometry and the same input conditions and model constants. Measured data were used to compare the results of the two CFD models, namely, the kappa-epsilon (к-є) model and the Large Eddy Simulation model. Despite the complex synoptic situations, different meteorological input data and fast-changing conditions, the simulation results from both the models were in good agreement regarding the dispersion of pollutants.

Jan 1, 2015

By James S. Redpath

"The ways of the world be many and most of the ways be tried, you follow in the footsteps of others till you come to the great divide". These words, written by Robert Service a long time ago, come to mind when I think of our original attitude upon entering into a contract with the International Nickel Company to sink the deepest shaft in the world outside of the Union of South Africa. This shaft was to be sunk to a depth of 7,137 feet from surface, and while it was recognized by all concerned to be a somewhat unusual undertaking in our part of the world, the fact that quite a few shafts had already been sunk to this depth in South Africa probably gave us the feeling that we were following in the footsteps of others. In retrospect, because this shaft was being sunk under entirely different conditions than those existing in South Africa, we were in fact venturing into an entirely new area of endeavour without properly recognizing this fact. It has occurred to me that others considering a similar type of job could benefit from our experience, especially in an assessment of the risks involved and how they compare to those encountered in an ordinary shaft. For comparison purposes, I would define an ordinary shaft as being sunk to a depth of 5,000 ft or less, and a deep shaft as one being sunk to a depth of between 5,000 ft and 8,000 ft. The sinking of the Creighton No. 9 Shaft has been de-

Jan 1, 1997

By Erika Moonin, Jim Nickerson, Marcus Jensen

"This paper will explain how the Contractor and Owner avoided a contractual dispute involving characterization, impacts, and final remedy for challenging ground conditions encountered during drill and blast excavation of the starter tunnel required for launch of the tunnel boring machine (TBM). During excavation more than 600 feet underground, the Contractor encountered a large complex fault zone subject to more than 14 bar of water pressure. Successive ground inflows from the fault complex over a six-month period presented significant technical and partnership challenges for the team and ultimately delayed the project by nearly one year. This paper will discuss how the Contractor, Owner, and their respective consultants worked together to address these challenges, make decisions, and ultimately move the project to successful completion. PROJECT BACKGROUND AND NEED Seven states of the western United States of America rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River basin, including the Rocky Mountains, the Wind River Mountains, and the Uinta Mountains. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. During the 1980s and 1990s, snowfall was relatively abundant and Colorado River flows were high on average. Beginning in the year 2000 and continuing to the present day, snowfall has been well below documented historical averages and Colorado River flows have diminished. In fact, a trend toward diminishing flows is evident during the period of the historical record. This variability in Colorado River flows and the trend to lower flows is represented in the following Figure 1."

Jan 1, 2016

By Allen G. Taylor

High-value materials, such as gold, platinum and other precious metals, are subject to loss through unauthorized removal from mines, smelters, refiners and other places where such materials are processed. A study by Gastrow (2001) determined that between 1994 and 1998 an average of 603 kg/a (1,330 lb/year) of gold was stolen from South African mines and subsequently recovered. This does not include the gold that was stolen but not recovered. At 2011 prices, 603 kg/a (1,330 lb/year) of gold would be worth approximately $33 million. Mine security personnel believe that the unrecovered stolen gold far exceeds what is recovered (Gastrow 2001). Traditionally, metal detectors have been used to screen personnel leaving secure areas to discourage such unauthorized removal. However, with the current near-record prices of gold, platinum and other precious metals, it has become worthwhile for people exiting a facility to walk out with quantities of product that are too small for ordinary metal detectors to register, resulting in substantial financial losses.

Jan 1, 2012

By S. Odell

The Bureau of Land Management (BLM) has constructed two biochemical reactor systems (BCRs) to treat mining influenced water from the Forest Queen Mine near Silverton, CO. The bioreactors coupled with a natural wetland provide treatment to the Forest Queen Mine drainage. The central objective of this paper is to review the performance of the bioreactors and wetland treatment system. The bioreactors have been in operation for nine years and along with the natural wetland are still removing a high percentage of the influent metals.

Jan 1, 2010

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread-sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin. Computerized search Computerized search approaches represent crude first attempts at letting the computer design the blend. Unfortunately, the blends found by these programs are very often less satisfactory than those developed manually. The way these techniques work is that they design, according to some predesigned pattern, a number of different blends and then quickly evaluate them. It is then straightforward to select the best from this sample set. The quality of the results depends on the number of blends designed, the way they differ from each other (the search procedure), the number of sources available, the number of quality specifications, and the severity of the specification limits. Good results are usually obtained for small, simple problems. At best, the results obtained are inconsistent from one blend to the next. Programs of this type are advertised in the mining literature. They usually mention how many different blends are evaluated, making it clear that this is more than can be tried manually. Expert systems Expert systems use a source of information known as a knowledge base. The knowledge base, usually a set of if-then rules, attempts to reconstruct the deductive reasoning process of an expert in some job capacity. For coal blending, the usual trial-and-error process has an easily recognized pattern of rules that are followed to try to find a better blend. By following these rules, it is possible to home in on the best blend without the exhaustive search required by the previous method and without the manual manipulation of the spreadsheet approach. The use of an expert system accomplishes this. One of the rules may say something like "if BTU is out of spec, then add more in the blend from a source having a high BTU and subtract some from a source having low BTU." In other words, it goes through the trial-and-error process. The process continues until all specifications are achieved and can continue further to try to optimize the cost. Of course, less simplistic rules are also needed. One set of rules would determine maximum changes in the tonnage added or deleted to the blend or from any one source. Other rules would be needed to determine which quality to improve if two or more are out of spec. At this level, the process of building the knowledge base provides the engineer with a deeper understanding of his or her own thought processes. The advantage of obtaining better blends is clear for this approach. Two more advantages should also be apparent. One is that it follows the same common sense logic that is used when doing the blends by hand or by spreadsheet, making it easy to understand. The other is that, like the search procedure, it designs the blend rather than just analyzing manually designed blends. Thus, it has all the good features of both approaches discussed thus far while providing improved results over each. A final advantage is the ease of use and ease of development. The expert system shells that are on the market are very easy to use and can be run on microcomputers. Linear programming Linear programming is an algebraic tool that solves a set of linear equations to yield an optimal solution to a problem. The optimal solution is based on the linear model so the results are only as good as the ability of the linear model to accurately portray the reality of the problem situation. It is fortunate for the coal blending problem that a linear model can be devel¬oped that reflects exactly the problem that is required. Unfortunately, the mining industry has been slow to use this tool. Coal blending applications available that use linear programming take one of three forms. The first, requiring exper-

Jan 12, 1988

By Y. Guan

The dissolution behavior of silver and copper from silver/copper alloys in ammoniacal solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of composition of alloys, concentration of lixiviants, stirring speed and temperature on the overall dissolution kinetics has been studied. Silver / copper alloys of three compositions were used in this study. The atomic percents of silver in these alloys were 76.9, 46.9 and 24.1. The results on the rate of dissolution obtained for these alloys have been compared with that of pure silver and copper under the same testing conditions. A particular emphasis has been given to the galvanic effect on the overall dissolution rates.

Jan 1, 1993

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Mine explosions are one of the most concerning risks related to underground coal mining, as a single gas explosion can cause injuries and fatalities among miners. Underground infrastructure seals and build-in-place (BIP) refuge alternatives (RAs) are employed to isolate an area from active workings to mitigate coal mining-related accident risks. They are designed to withstand blast pressures from a possible accidental detonation of the contained gas or a coal dust explosion. Crosscut seals and BIP RAs, typically consisting of steel-reinforced concrete, are prone to strong convergence and have a significant leakage potential due to high convergence damage near mined-out areas. The roof-to-floor convergence can change the structural integrity of these structures, and altered structural integrity can lead to less explosion resistance capability. Hence, a thorough analysis is needed to further understand their explosion response under various strata conditions.

Jul 1, 2023

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985