Search Documents

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12'-6" diameter Wirth hard rock TBM.

Jan 1, 2005

By Michael E. Stickney

"Soft technology" computers and computer programs-brings to mind a room full of machines, tape drives, disks, plotters, and printers spitting out financial reports. Computers now have a much broader scope of applications because of reductions in equipment size and cost. For example, people now interact directly with computers to control events. Such computers and associated equipment-called interactive control systems-are often small, relatively inexpensive, and can be designed to increase productivity at mining operations. This is accomplished by improving communications between individuals; giving employees the information needed to make decisions in real time, as events are happening; and giving individuals the background needed to perform more effectively. This paper will describe a procedure for determining the return on investment for interactive control systems, and describe four such systems. The analysis process is general in nature and can be applied to any type of mining operation or production process.

Jan 4, 1981

By X. Song, Q. Zhang

"The development of fracture zones in surrounding rock mass has significant impact on the stability of underground mine roadways. Detection of the fracture zones is of compelling importance for maintaining roadway stability as well as for safe and speedy excavation of the roadways. This paper presents a study conducted at Dong Bao Wei underground coal mine, where the roadways were developed in diabase rock mass. The roadways suffered severe damages, including sloughing and excessive floor heaving. The borehole imaging technique was applied in the study to observe and detect fracture zone development surrounding the roadway openings. Based on the borehole imaging studies, new roadway support systems were proposed to improve the stability. INTRODUCTION At the Dong Bao Wei Coal Mine three main roadways of the west wing were excavated. The three roadways had semicircle arch cross sections and were at a depth of 650 meters, each being about 750 meters in length. The roadways were driven through a section of thick diabase intrusion, which was softened by water with reduced strength and may turn into powder form under weathering. Site investigation indicated that the roadways in diabase intrusion zone were badly damaged due to severe deformation, and very serious roadway sidewall sloughing and spalling accompanied by severe floor heave often occurred.(Figures 1 and 2) In order to ensure the normal use of the roadway, undercuts were excavated. However, this operation seriously affected the roadway construction progress and increased the amount of roadway support operations as well as the roadway maintenance costs. Furthermore, a roof fall accident occurred in nearby drilling site. The investigation indicated insufficient support provided for the roadways which imposed significant safety hazards and would have serious impact to mining production and subsequent mining activities.The support of the main roadways is a critical task and is the focus of the underground opening excavation work at the mine, since more than 40 years of service life is required from these main roadways. For these roadways, large cross sections with high degree of stability and minimal amount of deformation should be maintained. Therefore, providing sufficient and appropriate roadway supports is of significant importance to the coal mine. In this paper, in order to optimize the roadway supporting system, studies were carried out on the geological structures, lithological characters, roof bolt anchoring features and suitable anchoring layers. The studies were aimed at ensuring the stability of mine roadways, reducing the roadway maintenance costs and providing a safe mine passageway for orderly production and progressive development of the mine"

Jan 1, 2016

By Stephen Phillips, Luigi P. Gonano

Vertical circular shafts have been proposed for multiple access to high level nuclear waste deep geologic repositories. Shaft construction is a critical path item in the commissioning of a repository. Other constraints on the shaft design and construction criteria include the lack of design precedence for long term performance and the importance of minimizing rock and groundwater disturbance. A comparative evaluation of conventional and mechanized shaft sinking techniques is presented in the context of the particular geologic and design constraints. Technical and non-technical factors for blind drilling, blind boring, raise-reaming, drill-and-blast and ream-and slash methods are reviewed for typically "hard rock" and "salt" type repository sites. Appropriate shaft designs are developed, the suitability of each method to the particular requirements evaluated and construction costs and schedules determined. The explicit appraisal of the significant design factors for each method serves as a rational basis for the preliminary selection of the most suitable sinking technique for a particular set of site/design conditions.

Jan 1, 1983

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

By Jürgen. F. Brune, CLAIRE STREBINGER, ADITYA JUGANDA, Gregory E. Bogin Jr

The abstract highlights the risk of methane gas explosions in underground coal mines and the potential of computational fluid dynamics (CFD) modeling to simulate such events and assess their impact on mine ventilation. The study focuses on developing CFD models for large-scale explosions in longwall mines, specifically simulating methane gas explosions resulting from face ignition during coal cutting. The research demonstrates the integration of a combustion model into a longwall mine ventilation model and shows how the availability of explosive gas mixtures significantly affects flame propagation and explosion pressure.

Mar 27, 2022

By James N. White

Completion of the Hall Street Coal Transfer Terminal in St. Louis marks the beginning of a major shift in the movement of coal to the power generating stations of the Midwest and South Central regions of the United States. The location of the terminal is significant. The 10 million ton- per-year facility is the first high capacity rail-to-barge transfer terminal to be built on the western shore of the Mississippi. This terminal and others to follow will link the massive coal fields of the West with the high coal consuming markets adjacent to the 25,000-mile Inland Waterway System.

Jan 1, 1979

By R. M. Schuster, F. M. Benavides

Samuel G. Bonasso The article by Benavides and Schuster provides an in-depth study of three transportation alternatives for a four-mine complex in western Kentucky. The examination of aerial tramways was not undertaken as an alternative solution. We feel this is an oversight since industrial ropeways are competitive with both belt conveyance and overland truck hauling. In fact, there are aerial tramway systems, operational today, which are 100 years old and operating with some original components. Maybe unfortunately, there are no fixed rules or guidelines whereby the most cost-effective means of transporting and handling material for a given situation may be selected. Each situation must be evaluated so the variables that influence the selection of the desired alternative can be clearly defined. However, there are in-place industrial ropeway systems that have proven economically feasible over a range of 1.6-50 km (1-31 miles). The more difficult the terrain, the greater the cost efficiency.

Jan 1, 1983

By Raymond W. Henn, Kent A. Pease, Glen J. Rorison

The paper focuses on construction of a 2.55-km (8,365-ft) long, 2.4-m (8-ft)diameter storm drain tunnel in Evansville, Indiana. The tunnel was driven through saturated soft ground varying from clay to fine sand. The paper presents: an overview of design and design rational including specific EPB machine requirements; the contractor’s proposed and accepted alternative construction methods and TBM design; and construction issues and performance. Some of the key points discussed are the use of the TBM in different operational modes for alternative ground conditions, the effectiveness of dewatering systems, production rates, and issues such as surface settlements and gas.

Jan 1, 2001

By Robert M. Matyas, P. E. Sperry, Robert J. Smith, A. A. Mathews

INTRODUCTION The first Dispute Review Board (DRB) was utilized on a tunnel project 20 years ago. Increasingly utilized on a wide range of construction projects, DRB's are becoming the norm on tunnel and underground projects. This paper summarizes the growth in this usage, uses observations and experience to establish that barriers to the utilization of DRB's are more perceived than real and that many arguments against the DRB concept are not valid, and notes some of the salient elements that should be considered in practice to optimize DRB effectiveness. The purpose of the paper is to provide an annotated checklist for current and prospective users. The basic concept, structure, and operation of DRB's are described elsewhere and will not be repeated here (ASCE, 1991). DISPUTE REVIEW BOARD USAGE A compilation of Dispute Review Board usage for tunnel and underground projects to January 1994 indicated use on 63 contracts with a cumulative construction value of $3.8 billion and a total of 60 disputes settled. As of that same date, DRB's were planned for another 63 contracts with an estimated construction value of $4.7 billion. (A listing of these 126 projects is available from the authors.) This success and popularity have spread to other civil projects as well as process and building construction. The increase in DRB usage has been exponential. See Figure 1.

Jan 1, 1995

By Brian Heer, David Young, Randall Essex

The Manapouri Power Station is New Zealand’s largest hydroelectric facility located on the South Island of New Zealand. Constructed in the 1960’s, it includes a 700 MW under-ground power station and a 9.8 km (6.1 mile), 9.2 m (30 ft) diameter tailrace tunnel. The output of the power station is currently limited due to excessive head losses in the tailrace tunnel. To remedy this situation, the Electricity Corporation of New Zealand (ECNZ) retained Woodward-Clyde to design a second tailrace tunnel and appurtenant facilities and prepare Contract Documents for construction. The Project will involve the construction of a 9.8 km(6.1 miles), 10 m (33 ft) diameter, TBM-mined tunnel, hydraulic control structures at the upstream and downstream ends of the tunnel, an underground dewatering shaft and station, and tailrace channel improvements. This paper summarizes the key design and construction issues addressed during the planning and design phases, outlines the risk management provisions incorporated in the Contract, and overviews the Interactive Tender Process (ITP)that was implemented during the pre-tendering and tendering periods.

Jan 1, 1997

By A. R. Biggart, A. Walters, G. J. E. Kramer

The Owner Procurement Process or OPP is a proven, viable alternative contract delivery method that is potentially applicable to many tunnel projects. Using the OPP, the owner specifies and procures major tunnel construction items such as tunnel boring machines and tunnel linings and provides them to a tunnel excavation contractor in order to manage risk and accelerate project schedule. However, due to industry perceptions regarding potential owner risk, it is seldom considered or is rejected out of hand. In fact, past performance demonstrates that the process significantly minimizes owner, contractor and over-all project risk and mitigates the impact of any claims and differing site conditions. The paper outlines how the process should be structured to achieve schedule, cost, quality and risk management benefits. Potential and perceived disadvantages are discussed and how the process can be structured to mitigate or avoid them. The planned implementation of this process on the tunnels for the Silicon Valley Rapid Transit Project in San Jose, California is discussed.

Jan 1, 2005

By Robert Rautenberg, Paul McDermott

This paper will discuss the construction of 15.9 km (9.88 mi) of tunnels on a project in Chicago, Illinois. The tunnels were driven utilizing two rock and four soft ground TBMs ranging in sizes from 7.39 m (24.25 ft) in rock down to 1.95 m (77 in) in soft ground. In addition to the mining, there are 63 upper level structures and 16 dropshafts averaging 61.5 m (202 ft) deep included on this project. Many diverse mining, excavation, support and lining techniques were employed on this project.

Jan 1, 1997

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

By Gordon T. Clark, James R. Struthers, Celal Kirandag

INTRODUCTION Project Background The Washington State Department of Transportation (WSDOT) hired the Seattle office of Parsons Brinckerhoff to lead a team of consultants to produce an Environ-mental Impact Study and perform conceptual and preliminary engineering. The pur-pose of the Alaskan Way Viaduct and Seawall Replacement project is to replace the existing earthquake damaged and aging viaduct and sea wall, adjacent the downtown waterfront of Elliott Bay, with structures that have improved earthquake resistance and that maintain or improve mobility and accessibility for people and goods along the existing corridor. With an estimated replacement cost over $4 Billion and construction duration exceeding 8 years, it is one of the largest transportation design projects on the West Coast of the United States today. Seattle, Washington is a city of over 2 mil-lion people in the Northwest corner of the United States. Ever since the Klondike Gold Rush in 1897, Seattle has been considered a departure point to Alaska. Because of this, the street along the waterfront was named the Alaskan Way in 1930. Alaskan Way Viaduct and Seawall The Alaskan Way Viaduct (AWV) carries State Route 99 along the shoreline of Elliott Bay through downtown Seattle and is a vital part of Seattle’s highway system. The viaduct carries approximately 110,000 vehicles per day or 25% of all north-south traffic through Seattle (Figure 1). It is 3.4 km (2.1 mile) long with 3 lanes in each direction and was constructed of cast-in-place reinforced concrete between 1952 and 1956. The wear and tear of daily traffic, salty marine air, and several earthquakes have taken their toll on the facility. Studies in the mid-1990s provided early evidence that the viaduct was nearing the end of its useful life. The viaduct’s increasing age and vulnerability was apparent by crumbling and cracking concrete, exposed rebar, weakening column connections and deteriorating railings. In early 2001, a team of structural design and seismic experts began work to determine whether it was feasible and cost-effective to strengthen the viaduct by retro-fitting it. In the midst of this investigation, a 6.8 magnitude earthquake shook the Puget Sound region (the Nisqually Earthquake, located 56 km (35 miles) from Seattle and deep below the surface) caused moderate damage to the reinforced concrete structure. WSDOT closed the viaduct for inspection and repairs intermittently for several days over a period of several months.

Jan 1, 2007

By José A. Rios, José A. Vidalôn

The case study of a highland area in the Central Andes of Peru, where many abandoned polymetallic mines are found, is presented. Some of these mines generate metal leaching and acid rock drainage (ML/ARD) or have potentially ARD generating (PAG) tailings/waste rock storage. Effluents are discharged into the first of two lakes in line, which act as reservoirs for irrigating an important valley in the desert coastal region. Drainage fees, their relationship with the deposit and the solid-wastes mineralogy are discussed, as well as variations in water and sediments composition, the benthos, and the aquatic/riparian flora/fauna in these lakes.

Jan 1, 2000

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019

Train services through the Channel Tunnel linking Britain and France where scheduled to be fully restored in February 2009 following several months of repairs after a major fire in the tunnel on Sept. 11, 2008. A lorry caught fire on a shuttle train carrying heavy goods vehicles bound for France through the 50-km- (31-mile-) long northern tunnel. The fire, that spread to other vehicles, raged for about 16 hours. The extreme temperatures of up to 1,000º C (1,832° F) caused extensive damage to about 600 m (2,000 ft) of the 7.6-m- (25-ft-) diameter tunnel?s concrete lining, approximately 11 km (7 miles) in from the French entrance. The Channel Tunnel operator, Eurotunnel, awarded the repair con-tract, estimated to be between ?50 to 60 million, to a consortium of Freyssinet, Eurovia Travaux Ferroviaires (ETF) and Vinci Energies. Freyssinet was appointed to look after the civil engineering works, while ETF would be responsible for track and overhead wire restoration and Vinci Energies responsible for other equipment. The technique of hydrodemolition, which uses high-pressure water jets to remove concrete from various structures, was specified as the method to remove the fire damaged concrete. Freyssinet subcontracted the concrete removal to the specialist hydrodemolition and industrial cleaning contractor Philip Lasserat.

Jan 1, 2009