Search Documents

By David Crouthamel, Raymond Henn

"The need to fill the void space or annulus created between an excavated tunnel or shaft and the final lining system has long been a requirement in underground construction. Most of those types of voids are created as a result of employing the two pass tunneling lining method. Filling of this void is called backfilling. For many years the materials used as backfill were primarily reinforced and non-reinforced concrete, sanded grout, neat cement grout, or blown-in sand/pea gravel. However, in the past 20 years the use of cellular grouts/cellular concrete as the backfill material has greatly increased. Most cellular grout is made of a mixture of water, Portland cement (with or without the addition of fly ash), a foaming agent and admixtures such as a water-reducer or superplasticizer.It is the authors’ preference to use the term cellular grout as opposed to cellular concrete since by ACI Concrete Terminology an ACI Standard (ACI CT 13), concrete contains aggregates. Normally cellular grout does not contain sand (finite aggregate), but almost never contain course aggregates.The authors believe there are several reasons for this increased use of cellular grout as backfill, such as:• The increase utilization of the various trenchless tunneling methods. Tunnels constructed using trenchless method tend to be smaller in size, excavated diameter or cross sectional area. Making man-entry for placing backfill from inside the secondary liner, utilizing pre-installed grout posts, more difficult if not impossible. It is these workspace restrictions that are the drivers as to when to utilize grout ports installed during the pipe/liner fabrication versus grout delivery pipes installed within the void/annulus space.• The ability of cellular backfills to be pumped and flow longer distances.• The unit weight of cellular grouts can be controlled by mix design and generally can range from 560 Kg/m3 (35 lbs/CF) to 1040 Kg/m3 (65 lbs/CF)."

Jan 12, 2017

By Curt Swanson, David C. Mathy, Dru R. Nielson, Kent VonAspern

In 1997, Central Contra Costa Sanitary District undertook the design of the Martinez East Side Trunk Sewer Improvements Project. Microtunneling was specified for approximately 1,035 meters (3,400 feet) of 600-mm (24-inch)diameter pipeline to be installed through estuarine soil deposits (San Francisco Bay Mud) and alluvium beneath the congested city streets of downtown Martinez, California. Directional drilling was specified for approximately 275 meters (900feet) of 200-mm (8-inch) diameter pipeline in four separate segments to be drilled through bedrock within narrow utility easements between residential properties. This paper presents a case history for the design and construction of themicrotunneling and directional drilling aspects of the project.

Jan 1, 1999

By Andrzej M. Wala

A knowledge of the friction factor (K-factor) is necessary in planning and designing mine ventilation systems for least cost and highest effectiveness. The friction factor used must be accurate and reliable for correct estimation of airway resistances. At present, the friction factors are determined by using tables of published values. These values were established principally for metal-mine openings having small effective areas. This presents a problem to the ventilation design engineer whose responsibilities center around the design of effective ventilation systems for large room-and- pillar mechanized underground coal mines. Friction factors selected from these tables could be excessively conservative for large scale room-and- pillar operations. With only limited data on the K-factor (which are considerably site dependent) for Kentucky's coal mines and for all the above mentioned reasons, it was concluded that there is a need for field investigations to determine these values in-situ for existing mining conditions in Kentucky. The author describe the study carried out in ten coal mines located in eastern and western Kentucky and present the results of the investigation in both tabular and graphical form.

Jan 1, 1991

By Erik Westman, Brandon Stables, Benjamin Mirabile

"Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of standing support and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data.INTRODUCTIONA hydraulic load cell, more commonly known as a flat jack or JackPack, is a device installed to determine the loading characteristics of the roof-to-floor supports. These standing or roof-to-floor supports include, but are not limited to pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports.Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. Preloading helps to keep the supports, such as timbers props and cribs, in place during the dynamic loading associated with blasting (Barczak and Tadolini, 2004).Flat Jacks are manufactured in various shapes and sizes depending on the application; common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed, as shown in Figure 1. These load cells are produced in South Africa and can be formed into several different shapes depending on the application (Barczak, 2003). The sheet metal that makes up the bladder is comprised of 19-gauge or 1.11 mm (0.04 inch) thickness; the top and bottom pieces of sheet metal are resistance-seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow fluid to fill the unit, and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1,724 kPa (250 psi), the pressure relief valve keeps the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure.The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements, a pneumatic powered pump, hydraulic pump, or hand pump may be required to inflate the load cells."

Jan 1, 2019

By R. Perlo

"INTRODUCTION Peoples’ and operators’ safety in construction are tightly linked to the engineering choices, as much as the necessity of reducing time and costs of realization. Therefore, it is of paramount importance to address them properly from the earliest stage of the design, identifying the risks connected to the work and the variability of such during the different phases of the project. Risk is often measured as the expected value of an undesirable outcome. Regarding to occupational safety and health, the risk is the likelihood that a person may be harmed of suffers adverse health effects if exposed to a hazard. This combines the probabilities of various possible events and the assessment of the corresponding harm into a single value. However, the actual occurrences are often more complex than a single binary possibility case. In a real case scenario, with several possible accidents, the total risk is the sum of the risks for each different accident, provided that the outcomes are comparable. The semi-automatic tunnel support system along with its erector machine proved to be a solution with improved structural performance, able to reduce the time and yet to deliver an enhanced, quality-aware and safer working environment for the operators. The implementation of the system provides the engineers, the contractors and the owners with an effective alternative option shortlisted in 2015 for the ITA Award for the Safety Innovation of the Year. In a market industry driven by safety and time constrains the efficiency shall be the ultimate goal, in order to provide solutions able to negotiate with the most challenging ground conditions. In this paper, the authors describe the recent developments on regard of this whole new tunnel support system, including design approach and presenting related case histories OFFSETTING THE RISKS Considering the above factors, from the manufacturers’ point of view, an effective way to limit the construction risks is to focus on the material and technological characteristics, their application and the risks related to them including any residual risks. Finally addressing the construction needs also involves time and cost-effective solutions. The path to follow is an integrated approach where the efficient management of the risk is supported by a flexible, user-friendly, and time effective product that is able to provide a safe, reliable and viable solution to address the construction requirements. Therefore, in a market sector driven by safety and time constraints, the efficiency is a key goal, in order to avoid redundancy and yet to deliver a safe working environment able to meet the construction schedule. The safety of all the parties involved is given by stable working conditions, either for the workers, or the operators and eventually the public. Therefore, the solutions provided should ‘strengthen’ the overall condition and such “to limit or to reduce the deformations within acceptable designed limits and to prevent [the tunnel] to collapse” [1: Clause 207.1.4]."

Jan 1, 2018

By R. S. Jurani

Sunshine Mining Co.'s Kellogg operation is the primary silver producer in the US. Maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and un-certain silver markets, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a two-year, $400,000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants. This saved the company about $650,000 per year.

Jan 1, 1988

By Sergio Flores, Nate Long, William Hodder, Phil Rhodes, Tim McQueary

The Surface Water Supply Project Segment B3 is a 4 miles section of tunnel that will run East- West in Houston TX, from Hopper St to I-45. The tunnel will be mined by using a 128" Dia refurbished 1987 Lovat Tunnel Boring Machine capable of operating in Open or EPB mode. The tunnel will be temporarily supported with ribs and lagging and a 96" Dia pipe will be grouted into place. All four miles of this project are within Petroleum Pipeline Easements. The project includes seven shafts, 2000' of tunnel in potentially petroleum contaminated ground, crossing the Hardy Toll d, I-45, the nion Pacic ailroad ight of Way and multiple oil and gas pipeline crossings. This paper summarizes the planning and drive performed to date.

Jun 23, 2024

By Ernest L. Bradley

A positive pressure ventilation system, augmented by a dewatering well curtain and underground longhole drilling, provides effective ventilation and radon control at EXXON Minerals Company's Highland Underground Mine in the Southern Powder River Basin of Wyoming. Testing different types of bulkheads, sealants, and bleeder systems has led to improvements in the basic ventilation system. Continued testing of new or different materials and equipment is expected to lead to further improvement in the ventilation program. Effective training of both miners and supervisors is essential to maintaining and improving ventilation techniques. This paper addresses the ongoing ventilation program and experience to date at the Highland Uranium Mine.

Jan 1, 1979

By S. Pastor, S. Hahn

"As the concept of autonomous haulage systems (AHS) moves from prototypes to production-ready applications, the operating performance of the haul road will become critical to the overall success of autonomy in mining. Deterioration in road performance will require remediation, human intervention and significant, albeit temporary, changes to operating procedures, to accommodate road maintenance. With autonomous trucks comes the opportunity to reduce road formation and operating width. This will, therefore, generate potentially significant reductions in stripping ratios and improvements to mine economics, but only if the design of the road, and its associated deterioration rate, is predictable and manageable, based on the materials used to construct the road and the maintenance interventions to be carried out on the road.This article presents the assessment of a digital photogrammetric approach to the characterization of a mine haul road surfacing, or wearing course material. Design and maintenance parameters for these roads are currently determined partly from physical particle size distribution (PSD) assessments of ‘in-road’ material. However, this approach does not accommodate the need, nor leverage the benefits from, AHS. The digital imaging approach is assessed in this article, using two standard digital analysis software tools, together with in-service mine haul road wearing course samples and images that are analyzed to determine the applicability and reliability of the approach to deliver a real-time assessment of haul road surfacing conditions and thus to identify the road maintenance interventions required to address deterioration.Enhancements in mine road design, construction and management for the past 20 or more years has largely been focused on short-term tactical needs. These improvements have not been matched by advances in the fundamental technologies that underpin mine road design and management and, although the quality of mine roads have probably"

Jan 1, 2015

By Armando M. Lago

This paper reviews the postwar changes that have occurred in the expenditure and financial behavior of mineral corporations, and in particular the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample in Section I, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail in Section II. Section III formulates an econometric model of mineral corporate financial behavior which is then estimated and reviewed in Section IV. Section V discusses policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector. Finally, the optimum financial structure of mining firms is discussed in Section VI, which analyzes the effect of corporate financial structure on the mining corporations' average Cost of capital.

Jan 1, 1969

By Paul C. Schmall

In recent years, several geotechnical methods have been successfully applied to ash pond closure. These include modified dewatering techniques with wellpoints and wells to physically drain the material, soil mixing to create a soil-concrete material for improved accessways as well as improved ground structures within ponds to act as barriers or gravity dams, and geotechnical instrumentation to serve as an early warning of the potential for liquefaction. Given the parallels between fly ash and sluiced in place mine tailings, the application of fly ash remediation method to mine tailings shows significant potential, as illustrated in this paper.

Feb 1, 2024

By Feida Wu, Yuhang Liu, Huimin Gao, Yuhan Song, Zhi Liu, Zijie Ren

In the process of quartz purification by calcination water quenching, the different expansion rates of gangue minerals and quartz were used to produce cracks or remove fluid inclusions, which is conducive to subsequent purification. However, the role and mechanism of calcination-water quenching are still lacking in research. In this paper, the position of calcinationwater quenching in gangue quartz purification process was adjusted and the removal effect of calcination-water quenching process at different nodes in the process was explored. The results show that the purification effects of grinding-calcinationwater quenching-classification-acid leaching process and grinding-classification-acid leaching-calcination-water quenching process were relatively good. The main reason is that calcined water quenching can make quartz produce cracks, which are more rough. At the same time, calcined water quenching is located after grinding, which has a larger specific surface area, pore volume and pore diameter, and has a strong adsorption capacity for acid solutions.

Nov 2, 2023

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By J. A. Ober

"In 2016, the estimated value of total nonfuel mineral production in the United States was $74.6 billion, a slight increase from the revised total of $73.4 billion in 2015 (Table 1). Increased construction activity spurred increased production of industrial minerals, especially those used in infrastructure and residential construction. Although starting the year relatively low, prices for several metals, especially for some of the precious metals, began to trend upward. Decreased production of most metals produced in the United States, however, contributed to an overall decline in the value of metal production.Several U.S. metal mines and processing facilities were idled or closed permanently in 2016, including iron ore mines in Michigan and Minnesota; three primary aluminum smelters in Indiana, Missouri and Washington; one secondary zinc smelter in North Carolina; a titanium sponge facility in Utah and titanium mineral operations in Virginia. In addition, in May, the weekly average rig count for oil and gas drilling reached its lowest level since the 1940s when that measurement was first recorded. The reduced drilling activity resulted in decreased production of some industrial mineral products used in the drilling sector. Trends in mineral-related sectors of the domestic economy declined or held steady, except in the manufacturing of nonmetallic mineral products and nonferrous metals excluding aluminum, which increased. Overall, mining trended downward as the result of significant declines in coal mining, oil and gas extraction and metal mining (Table 2). Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, which have higher production quantities but are lower-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of construction aggregates are orders of magnitude larger than those for most other mineral commodities thus making direct compar"

Jan 5, 2017

By Hugh Douglas

This paper discusses the financial health of the U.S. mining industry and its ability to meet the future raw material requirements of this country in the context of resource independence. The title of this paper begs several questions, and three will be raised here. The answers to them will form the basis for discussion. The three questions are: What does one mean by resource independence. How is the U.S. mining industry defined. How is financial health measured.

Jan 1, 1977

By A. K. Raina

Blast induced damage to the final wall of rockmass in any civil or engineering application is a major concern to the rock excavation engineers. There are at least four distinct techniques practised by blasting engineers to minimise the damage to the parent rock during blasting that are classified as contour blasting. One of the methods to achieve a smooth wall or rock surface in blasting is pre-splitting, where blastholes in the final row are mildly loaded with explosives and fired first in sequence before the rest of the holes in a round of blast to achieve a split in rockmass. Since blasting is one of the most adopted methods for achieving a final wall in a desired shape, while maintaining the rockmass integrity, the design of pre-split blast assumes importance. There are several variables that determine the final shape of the pre-split face including the rock type, the drill diameter, the explosive characteristics, the orientation of major joints with respect to drill hole, the linear charge density, the spacing of drill holes and inclination of the drill holes. This study attempts to determine the importance and sensitivity of variables in pre-split blasting using historical data from open excavations of a hydroelectric project in India. Keeping in view the multitude of variables, low correlation of independent variables with responses and high level of interactions between the variables that define the blast results, it was found suitable to use ANN to determine the importance and sensitivity of the variables involved. A new method to determine the blast induced damage to rockmass, namely, undamaged area (AUD%), is introduced. Half Cast Factor (HCF%) and AUD%were calculated for a high wall and trenches by digital image analysis technique using the Fragalyst software. Joint spacing and linear charge density emerged as most controlling variables in determining the final result of pre-blast. The relative importance of other variables assuming significance in the case of both the designed outputs is also discussed. A comparative analysis of HCF%and AUD%on the basis of results obtained from ANN analysis is also presented. A futuristic approach concept has also been introduced.

May 30, 2021

By W. C. Hirt

Selective flocculation was used to produce superclean zinc concentrate with minimized silica contamination. Research was carried out on a flotation concentrate from the Jersey Miniere Zinc Company (JMZ) in Gordonsville, Tennessee. The material was first dispersed with sodium silicate and then causticized tapioca starch was used to selectively flocculate the sphalerite, leaving the silica in suspension. This technique has been applied commercially to iron ore beneficiation but has never been used for processing zinc. The feed material assayed 0.45% Si02. Use of 0.56 kg/tonne (1.13 lb/st) of sodium silicate and 0.070 kg/tonne (0.141 lb/st) of causticized tapioca starch resulted in 98.2% zinc recovery in a purified zinc concentrate assaying 66.0% Zn and 0.24% silica. The present target level for silica contamination in JMZ zinc concentrates is 0.3% Si02. This work has shown that selective flocculation offers a potential method for cleaning flotation concentrates, particularly where low silica products are required.

Jan 1, 1993

By M. R. Carter

The Rochester Mining District is located some twenty-five miles NE of Lovelock, Nevada. The District was discovered and named in the 1860's by prospectors from Rochester, New York. For a number of years, they worked Rochester Canyon, sinking shafts and inclines and making open cuts. After reaching a depth of approximately eighty feet, the miners tapped an underground channel and were driven from these workings by a strong flow of water leaving pumps in the shaft and barely escaping with their lives. With the Rochester workings no longer accessible, the miners went to the southeast and established the Relief Mining District. About 1881, gold was found in the gravel at the mouth of American Canyon, to the east of Rochester. These placers were worked until 1895, first by the Americans who reportedly took out $1 000 000, and later by the Chinese who mined the gravel with great skill. It was estimated that the Chinese took out as much as $10 000 000.

Jan 1, 1987

By E. Martinez

A heavy mineral sand sample was tested containing 13% heavy mineral consisting of rutile, zircon, and ilmenite. Eleven tests were run at a mill site with a Mineral Deposit Limited MG 4 spiral to determine the effect of the addition 0; magnets to the spiral compared to conventional gravity separation. Different magnet configurations and field strengths were tested. Optimum results were obtained with the spiral retrofitted with magnets. The heavy mineral content of the concentrate was increased from 55.5% in the control to 64.2% with the magnets. The 8.7% improvement in heavy mineral recovery was due not only to the weakly-magnetic ilmenite, but also to increased recoveries if the non-magnetic zircon and rutile. The increased recoveries were achieved with no loss of concentrate grade.

Jan 1, 1992

By D. A. Augenstein

Operators of coal preparation plants use equipment such as large-capacity dump trucks and bulldozers to haul, spread and compact refuse material to conform to federal and state regulations governing the disposal of solid waste. For example, federal regulations require that refuse be spread and compacted in layers not more than two feet thick. If the refuse layers or piles have poor load-bearing characteristics, movement of equipment over them becomes extremely difficult. The increasing cost and limited space for the construction of settling ponds extensively used for fine refuse disposal are leading to the growing practice of dewatering the fine refuse by means of vacuum disc filters and combining the resulting filter cake with coarse refuse for waste bank disposal. However, this filter cake usually contains more than 25% moisture. Therefore, when it is combined with coarse refuse, the moisture level of the total refuse may become high enough to impair the load-bearing strength of the refuse. Precisely this problem and the attendant difficulties of moving heavy equipment arose when vacuum disc filters were installed at a preparation plant in West Virginia. Combining the moist filter cake with the coarse refuse generally results in a 12% moisture level for the total refuse at this plant. At this moisture level, the refuse can still be handled with some difficulty by the equipment. However, the problem has frequently been compouned after rains.

Jan 1, 1977