Search Documents

By Lianhui Jia, Yali Han

"The key technologies of a large rectangular pipe jacking machine with dimensions of 10.12m × 7.27m (width x height) include selection of rectangular cross-section cutting modes, analysis on the strength and stiffness of the rectangular shield, integrated control of electro-hydraulic proportional thrust systems and ground conditioning for excavation are presented in detail in this paper. These key technologies have been successfully applied and verified on site during tunneling, providing a new concept for the building of large rectangular traffic and pedestrian tunnels in urban areas for the future.1 INTRODUCTIONIn the past, underground tunnels were mainly used for drainage, sewage, utilities, metro tunnel, etc. and most of them had circular cross-sections. Recently, as a result of economic development, gradually accelerating urbanization process and diminishing ground space, underground tunnels have already become a new trend for urban underground space utilization. Due to the heavy traffic flow, the demands for rectangular cross-section underground tunnels, such as pedestrian underpass and road tunnel, are increasing gradually.The Rectangular pipe jacking machine (hereinafter referred to as RPJM) was firstly developed in Japan for the construction of metro station, pedestrian underpass, underwater tunnel by-passes, etc. Kazunaki Kawai et al. introduced a RPJM developed and manufactured by KOMATSU in 2002 [1]. Tosikazu Kubota et al. confirmed the rectangular tunnels’ superiority to circular tunnels with regard to larger inner cross-section and lower construction cost in their RPJM construction reports [2]. Compared to circular pipe jacking machines, a RPJM also has the merits of a higher inner tunnel space utilization ratio and is able to excavate in shallow overburden areas. As shown in Figure 1, the effective area of a rectangular tunnel is more than 20% higher than that of an equivalent circular tunnel."

Jan 1, 2016

By Gennaro G. Marino

This paper summarizes and evaluates data on mine subsidence ground movements and associated damage for houses in Illinois. Based on the data collected, the response of homes to subsidence ground movements is expressed in terms of repair costs. A damage criteria is then proposed that relates the ground movements and damage levels. The data were collected as part of a comprehen¬sive study performed for the Illinois Abandoned ?Lined Lands Reclamation Council, A -M-RC, by the Civil Engineering Department at the University of Illinois, and probably will be published in late 1934 by the council. The study concentrated its efforts on surface ground movements and the effects to houses over abandoned room and pillar mines. The resultant surface subsidences are commonly dish or bowl shaped and are termed sags. Method of Analysis The steps in analysis used to arrive at the proposed damage criteria are: 1. Canvas and rap subsidence damage in houses, 2. Assess the associated ground movements, 3. Estimate the damage repair cost, 4. Develop a damage/repair level classifica¬tion, 5. Correlate the associated ground movement, damage/repair level and home construction type, 6. Propose a damage criteria.

Jan 1, 1984

By BARBOSA AMILTON, Denise C. R. Espinosa, David B. Dreisinger

Chelating resins can be used to recover important metals from different sources, and it is important to understand which resin is most suitable for each metal [1]. This review  benefits the mining industry because chelating resins can be used to recover metals from low-grade ores and mining tailings, increasing the industrial process efficiency [2–4]. Furthermore, the use of chelating resins in mining processes and mining tailings has the common problem of metals contamination, with iron being the main contaminant in low-grade ores and tailings. Understanding how contaminants decrease ion exchange efficiency is significant for industries [5

Underground instrumentation and observations at longwall panels have demonstrated that the growth of main roof causes an extremely high roof weighting on the shields. It can sometimes result in catastrophic effects on the support when the roof weighting intensity far exceeds the support capacity. In this paper, a comprehensive study was conducted on characteristics of main roof breakage and its effects on shields at different locations, based on the monitored shield data, theoretical analysis, and finite element analysis. With the help of theoretical analysis and numerical modeling, stress distribution and redistribution in the main roof were analyzed in detail to define main roof failure modes and understand the maximum roof weighting intensity imposed on the shields. From this study, it was found that the effects of main roof breakage on shields are chiefly related to the shield initial setting condition and the final failure mode of the main roof.

Jan 1, 1994

By T. J. McKeon

Gravity separators such as spirals are commonly used in multistage cleaning and scavenging circuits to improve the quality and recovery of concentrates produced in the industrial minerals industry. Unfortunately, field surveys suggest that many industrial operations are poorly configured in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiency of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Feb 1, 2012

By Paul Soros

There has been a steady increase in shiploading capacities in the last 20 years. One of the reasons has been the general increase in ship sizes, with the largest vessels currently around 280,000 DWT in the bulk trades. Obviously, the large vessels can accept loads faster and their economic utilization justifies higher loading rates, up to a point. The high capacity facilities have loading rates far beyond this point. The economic logic of these facilities is based on the fact that for a given annual throughput the capital and operating cost of a single high capacity system is less than that of two smaller systems. Thus, where the projected throughputs are large, there is a great incentive to reduce capital costs by maximizing capacity. Tubarao, in Brazil, designed for a 100 million ton per year throughput with one finger pier and one high capacity berth is a successful demonstration of this approach. In the current state of the art, the high capacity systems have shiploading capacities in the range of 10,000 - 16,000 TPH, for annual throughputs of 20 million tons and larger per loading berth.

Jan 1, 1982

By D. W. Hutchinson

One of the most important problems facing the coal industry today is the disposal of refuse from the coal preparation plants in a safe, economical, and efficient manner while complying with all legal requirements. The most commonly used refuse disposal method has been landfill/impoundment. In this method, the coarser refuse fractions are disposed of by layering and compaction into a landfill. The fine coal slurry refuse fraction is impounded in a dam constructed of a portion or all of the coarser refuse fractions. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the preparation, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. At the time of the promulgation of the new Federal regulations, United States Steel Corporation was in the process of designing the Cumberland preparation plant. As a result of the new regulations

Jan 1, 1977

By H. Sis

The pressure filtration behavior of dispersed and flocculated alumina slurries at high percent loadings is discussed with an objective to determine the effect of surfactant type and concentration on slurry properties. A high purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by surfactants that are considered to act by electric and steric stabilizers. The effect of both the ionic and nonionic surfactants was investigated. Surface charge measurements of the slurries were carried out by electrokinetic sonic amplitude (ESA) method to understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and final cake properties are discussed.

Jan 1, 1998

By Michael Forbes, Rick Jeuken

The challenge of managing geological uncertainty in mine planning is central to optimizing resource extraction while minimizing risks and costs. This paper introduces a novel approach to coal mine planning by integrating chance-constrained programming to address the uncertainty inherent in mining operations. The main takeaway from this work is the demonstration that focusing on reducing the variance of high-quality coal blocks, rather than low-quality ones, can lead to better blending outcomes, higher profitability and more efficient resource utilization. The study presents a case study of a coal mining operation, using chance-constrained programming to manage the uncertainty surrounding coal property predictions, specifically the predicted coke strength after reaction (CSR).

Jan 1, 2025

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By R. W. Hagemeyer

By way of background. it is important to keep in mind that the information presented in this paper relates specifically to synthetically produced precipitated calcium carbonate (PCC) fillers. Natural calcium carbonate fillers manufactured by grinding limestone, marble and chalk, though having similar chemical and physical analyses to PCCs, normally contribute somewhat different performance properties in paint, paper and polymer systems. Many factors have been cited and numerous theories have been proposed for the observed differences. Particle size parameters, surface chemistry and particle morphology are the items most frequently mentioned. A discussion of this subject is beyond the scope of this paper.

Jan 1, 1989

By C. Sun

Due to unfavorable geological condition, excessive deformation of mine drifts occurred in a large underground copper and nickel mine. In searching for a solution, a comprehensive underground monitoring program was implemented and the opening convergence and the surrounding rock deformation were monitored. A large number of field data were collected and thoroughly analyzed. The convergence and deformation as function of time and depth were determined and a rock stability index was proposed. Based on the deformation-time and deformation-depth relations, critical deformation times and locations were identified and defined as characteristic values to be used for mine opening and support designs. The characteristic values are critical in the application of two-step supporting system, and the determination of support parameters. The application of the method developed in this study has demonstrated that this practical approach in support design and installation is effective. With the two-step supporting system, a long-term drift stability can be achieved in the mine.

Jan 1, 1998

By William R. Barton

The domestic portland cement industry consumes more than 12 million tons annually of raw materials chemically similar to fly ash. How these materials are used and how fly ash can serve in their place are discussed. Factors influencing whether or not a particular plant will use fly ash in place of an alternate material are discussed.

Jan 1, 1968

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By John Mahoney

We live in a world of change and the mining industry is enjoying some of the most rapid changes today that have been seen in a long time, We'd like you to open your mind to a new concept in material handling. Figure # 1 Shows a new concept combining some of the proven application advantages of the power shovel with which we are all familiar, and applies the advantages of the dragline for the benefit of the user. First, the hydraulic excavator enjoys tooth forces of the shovel because the dipper is attached to the machine with a dipperstick and boom, and can often actually realize greater tooth forces than a shovel because of the prize action of the dipper in hard digging. Second, the hydraulic excavator enjoys the application advantage of the dragline because both the operator and the machine are up above, sitting on top where the operator oversees the excavation and the machine's operating work range is greatly increased.

Jan 1, 1973

By D. W. Jahn

Road construction in the near future will require contractors to guarantee that a project will remain trouble free for years after the project has been completed. These guarantees will challenge aggregate producers to become technically proficient in judging performance of their products. Testing procedures are described that may be used to predict performance of concrete and asphalt pavements before being committed into a construction project, and may also be used as quality assurance tools during construction to monitor performance as construction proceeds.

Jan 1, 1995

By R. Schipper

Two bench scale biochemical reactors (BCRs) were operated over a period of 3 months for the removal of uranium, radium, and selenium from mining influenced water (MIW). A BCR is an anaerobic reactor comprised of organic and inorganic substrate including woodchips, straw, sawdust, and limestone. Uranium and selenium are removed in a BCR by biological reduction of oxidized species (i.e., selenite, selenate) to less soluble forms (Pahler et al. 2007, Blumenstein et al. 2008, Rutkowski et al. 2013). It is believed that radium may be removed through absorption to the biomass in the BCR. The bench scale BCRs were constructed of 6 inch PVC columns with a top to bottom flow configuration. The bench influent water consisted of three different water ratios from two adit seeps. BCR hydraulic retention times of 24 to 36 hours were targeted during the study. Influent concentrations ranged from 19 ug/L to 1.86 mg/L for dissolved uranium, 12 ug/L to 270 ug/L for dissolved selenium, and 4.9 pCi/L to 24 pCi/L for radium 226. The average and maximum dissolved uranium removal was 93.6% and 98.5% respectively, the average and maximum dissolved selenium removal was 93.3% and 98.9% respectively, and the average and maximum radium 226 removal was 89.5% and 100% respectively.

Feb 23, 2014

By J. Loeb, R. Ramanathan, P. Cameron

All mining operations, including iron ore, maintain a focus of continuous improvement and asset optimisation in their operations. As all the operations in the Mine-to-Mill value chain are inter-dependent, available technologies that address efficiencies across the value chain are once again in the spotlight as companies are driven to improve productivity and maximise mine site profits to increase return on capital invested. Core to continuous improvement is the need to understand the baseline and the impact of changes to the process. In this paper, we discuss some of the key attributes in the mine to mill process, including their influence on productivity and cost, the need for direct measurement and areas where they should be applied. Many initiatives can be considered to improve mine to mill processes. Mining operations are planned and executed based on designs and models to achieve the operation’s objectives. However, there are many variables in the different parts of the value chain, such as blasting, material handling, crushing and screening. Measurement of the key attributes establishes the baseline for Mine to Mill (or Pit to Plant) performance which is necessary to understand the impact of any proposed improvements to the process design and execution and to monitor the outcomes on an ongoing basis to sustain the improvements that have been implemented. We have focused this paper on two types of measurement – blast movement and particle size of materials through the mine to mill process. Several innovative technologies are already available to measure these attributes and assist operations improve productivity and mine site profits.

Mar 2, 2022

By H. P. Ehrlinger

The Illinois State Geological Survey added Minerals Processing to its capabilities in 1966. Subsequently, the Minerals Processing Team and several Geologists collectively thought what neither would have thought of separately. The results included a number of projects. discussed here are: 1) The Utilization of the Fines from Kitty Litter as a Bonding Agent for Iron Ore Pellets; 2) Separating Plant Waste from a Commercial Silica Sand Producer into two marketable products, including a closely sized Silica Sand; 3) Marketable Feldspar Sand and Silica Sand from Dune Sands near the Kankakee River; and 4) A Method for Making Metallurgical Grade Fluorspar more desirable as Blast Furnace (Steel) Feed.

Jan 1, 2003

By Da-Rong Chou

An optimum method for selecting exploratory drilling locations has been developed. The process has been modelled as a highly non-linear programming problem subject to constraints. Solution involves an iterative algorithm which converges rapidly and procedures have been developed to distinguish between local and global optima. The algorithm has been implemented as an interactive computer program which allows the user to influence directly the solution process and to evaluate the effect of any manual adjustments to the optimal solution.

Jan 1, 1984