Search Documents

By Jun Ho Lee, Dae Young Kim, Ebrahim Farrokh, Ki Chang Hyun

"The Jinhae Geoje gas pipeline tunnel project is the largest (7.8 km) and the deepest (90 m) subsea tunnel in South Korea. This tunnel will house a pipeline to carry natural gas from the mainland to Geoje Island southeast of the country to alleviate the increased demands for natural gas, especially in the winter season. Tunneling is currently underway using two slurry shield TBMs of 3.5 m diameter. This paper describes the major design elements of the tunneling machines and their performance evaluation. For this purpose, a thorough analysis of geotechnical information was performed to evaluate the tunnel elevation to reduce the risk of tunneling under high water pressure in unstable and permeable rock mass under 9 bar water pressure. TBM specification and TBM performance were also analyzed using different methods, including well-known models as well as a rotary cutting machine test developed in house in Hyundai Engineering and Construction Company. INTRODUCTION High demand for natural gas, especially in winter season was the primary driving factor for the design of the Jinhae Geoje gas pipeline project. This project is located southeast of South Korea between Jinhae district and Geoje Island and runs for over 50 km length. The mid part of this project includes a 3.5 m diameter subsea tunnel consisting of two sections of Geoje to Jiri Island (4.3 km) and Jinhae to Jiri Island (3.5 km). Figure 1 shows the tunnel project location and its layout. Figure 2 shows the geological profile along the tunnel. As can be seen, the tunnel passes mainly through three rock types: granite, tuff breccia, and andesite tuff. This tunnel was planned to be constructed by two face pressurized shielded TBMs and to be lined with a segmental lining of 2.8 m internal diameter. The major challenge for this tunnel is its maximum expected water pressure at the tunnel invert (8.83 bar). At such a high water pressure, the TBMs required special design to ensure they can handle unexpected water pressure and to ensure the risks for the TBM maintenance intervention are minimal. In this regard, a thorough analysis was conducted on the TBM design parameters and geotechnical information to define required TBMs’ design parameters and to identify the safest tunnel elevation. This paper provides a brief overview of the project geotechnical information, TBM selection and its design specification, tunnel elevation selection, and TBM penetration rate evaluation. In this regard, a rotary cutting machine testing equipment was used to perform trial tests on a similar rock type encountered along the tunnel for performance evaluation and optimization."

Jan 1, 2016

By Craig M. Sams

Phosphate mines in Florida are continuing to encounter higher dolomitic content host rock with the phosphate pebbles(1) necessitating a change in grinding conditions and/or circuits, One of these changes is to install hydrocyclones and close circuit the mill as opposed to the traditional open circuit grinding plant. Close circuiting of the grinding mill with hydrocyclones allows one to take advantage of reduced process mill power requirements by circulating the coarse mill discharge back into the mill for multiple chances of particle breakage. Additionally, as in this case, the hydrocyclones de-slime the pebbles, allowing for more efficient use of grinding power by reducing the amount of dolomitic material recycled to the mill.

Jan 1, 1986

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites to determine the effects of this load transfer mechanism. The Bureau installed and monitored instrumentation at both sites to gather pertinent data on rock mechanics. At mine site A overburden depth varied dramatically in the vicinity of the study area and reached a topographic high at the study site: inner burden thickness was less than a pillar width (40 to 45 ft) (12 to 14 m): floor heaving was experienced in both coalbeds where sandstone and/or shale floor units were observed: overlays of the mine layouts show pillars were not totally super-positioned: a maximum of 5 in (13 cm) of roof to floor convergence was measured and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig (48,300 kPa) over instrument setting pressure.

Jan 1, 1989

By DEBASHISH MISHRA, SOMU MANDAL, ASFAR MOBIN KHAN, JAI KRISHNA PANDEY, NIROJ KUMAR MOHALIK, SANTOSH KUMAR RAY

Coal is a low-cost fuel with high calorific value. Statistically, the global coal mining industry suffered 12,489 fatalities in 104 reported mining accidents from coal dust explosions during 1900 to 2020. This review article discusses the occurrence, mechanism and explosibility parameters of coal dust explosions and presents a literature survey of the laboratory and computational fluid dynamics (CFD) simulation methods of studying them, as well as a comparison of the two methods.

Feb 1, 2023

By Philomene Verlaan

The Code for Environmental Management of Marine Mining (the Code) was adopted in 2001 by the International Marine Minerals Society (IMMS) following extensive and wide-ranging consultation, and updated in 2002. The Code provides a framework and benchmarks for development and implementation of an environmental program for a marine exploration or extraction site by marine mining companies, and for stakeholders in governments, NGOs and communities in evaluating actual and proposed applications of environmental programs at marine mining sites. The Code provides for its review by IMMS after five years, with a focus toward possible modifications based on experience with its implementation and in light of developments in the field of marine mining and associated environmental practices, in consultation with the marine mining industry and with other stakeholders at marine mining operations. As the review of the Code is now due, to begin the process, this paper will present an analysis of the Code and initial suggestions for its modification. Keywords: marine mining, marine environment, sustainable development, marine environmental risk management

Jan 1, 2008

By Robert F. Jones

INTRODUCTION Upflow Solids Contact Clarification is a process long employed in the treatment of potable water, wastewater and municipal sewage. This process incorporated in a fiberglass conical structure seems to offer an economical solution to problems encountered in reduction of particulates in uranium effuents. CONCEPT OF UPFLOW CLARIFICATION Use of suspended solids contact units date back to the 1930's. These types of units produced by Infilco and the Permutit Company, among others, were used in the Lime-Soda softening process to precipitate calcium and magnesium salts from hard water. In general, the process operated as follows: (a) Raw water entered a central chamber where it was mixed with chemicals. The chamber had provisions for agitating and circulating the chemicals so that mixing and reaction zones were formed. (b) The water, precipitated chemicals, floc and turbidity flows to a clarification chamber (the Permutit precipitator used a truncated cone). In most cases the influent then passes upward through a blanket of suspended floc and other solids before it leaves the chamber at effluent weirs or launders.

Jan 1, 1984

By Bill Reid

Coal companies mining the seams in the Appalachian region appear to be optimistic. Although some older mines are closing, newer mines are expanding. Money is being spent on new equipment and research to increase mining productivity, as well as improve safety. Coal has been produced from the rich Appalachian seams for about 200 years with no end in sight. Many equipment manufacturers have substantial backlogs of orders for new equipment. Some of the innovations being monitored by the Appalachian underground coal operators include au¬tomated longwall mining, continuous haulage systems and methane drainage. Appalachian coal was a major ingredient in the steel that culminated in the Golden Spike ceremony at Promontary Point, UT, where the final link in the transcontinental railroad was closed. This occurred on May 10, 1869, according to a history published by Union Pacific Coal Co. It stated that "rails and fastenings for track construction were purchased in Danville, Scranton, and Johnstown, PA and Troy, NY." Ever since, coal from the eight Appalachian states has contributed in no small measure to geographic expansion and economic growth of the United States.

Jan 1, 1995

By J. Kallioinen

Flotation of low grade Ni ores with serpentinite host rock tend to yield low recoveries of Ni With high MgO contents in the concentrate. The recovery can be enhanced by optimizing the sub-processes in the pulp and in the froth. The new OF-100 flotation cell has been designed to be adaptable to different feed fineness (Coarse, Fine). The losses can according the research conducted at Outokumpu's Hitura plant be substantially decreased by OF-100's new rotor and stator design and froth zone geometry. The froth residence time is used to adapt for feed particle size changes measured by the Outokumpu PSI- 200. Models for the behaviour of different particle Sizes in the sub-processes have been developed. The modified froth zone geometry and the capability of maintaining a froth of desired thickness allows efficient washing of the obtained concentrate producing low levels of MgO.

Jan 1, 1994

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018

By Nicholas T. Esposito

An advanced coal preparation plant has been built at Homer City, Pennsylvania, by Pennsylvania Electric Company, a subsidiary of General Public Utilities Corporation, and New York State Electric and Gas Corporation, as an alternative to utilizing flue gas desulfurization technology to meet the Federal Environmental Protection Agency and the Pennsylvania Department of Environmental Resources air quality emission regulations of 4.0 lb S02/106BTU for the two (2) existing coal-fired generating station Units No. 1 and No. 2, and a 1.2 lb S02/106BTU for the new Unit No. 3. The coal preparation plant is designed to process 5,200,000 tons of run of the mine coal annually and has a design capability to process 1,200 tons per hour via two (2) equal capacity 600 tons per hour preparation circuits.- The plant is designed to produce multi-product coal streams consisting of a middling product of medium ash and medium sulphur content, which is environmentally compatible to support operation of the two (2) existing generating Units I and 2, and a deep cleaned, low ash, low sulphur coal product capable of environmentally supporting the ambient air quality requirements of the new Unit 3 generating facility. The waste product from the process consists of high ash, high sulphur reject material. The process has the acronym MCCS (Multi-Stream Coal Cleaning System).

Jan 1, 1982

By D. Bristow, D. Baker, K. Awuah-Offei, A. ur Rehman

While a body of work exists on intelligent systems for guiding occupants out of buildings during an emergency, the problem of guiding miners out of a mine during an underground emergency has not been explored. Underground evacuation fundamentally differs from building evacuation because of differences in the regulatory regime and uncertainty regarding the number of occupants. The potential for implementing an intelligent miner guidance system is buttressed by the fact that miner tracking systems, along with communication and sensor networks, already exist in underground mines. This work presents a method based on a local positioning system, in the form of a network of “nodes” at major “intersections,” which can then be used to guide miners to safety. We have developed a path-planning algorithm, based on Dijkstra’s algorithm and the local positioning system that can provide miners with the optimal escape path in an emergency. The algorithm is validated with scenarios at the Missouri University of Science & Technology Experimental Mine demonstrating the potential to include smart technology in mine emergency management and response planning. INTRODUCTION Underground mines are hazardous environments with a higher than usual risk of safety emergencies where miners have to evacuate the mine to save their lives. Mines have always trained miners to evacuate or shelter-in-place in minimum time. Jalali and Norrozi (2009) opined that the three major components that help miners in case of emergency are pre-planned optimal escape routes, decreasing delays, and improving the education of miners. In fact, Goodman and Kissel (1990) suggested that fatalities arising from mine accidents could be reduced by 50% just by decreasing delays in finding the pathways in case of emergency. The proposed work can assist miners in finding escapeways quickly in case of emergency. It is very important to have a pre-planned evacuation strategy that is clearly communicated to miners to ensure the safety of all (Conti, Chasko & Wiehagen, 2005).

Jan 1, 2019

By K. Chandrasekaran

Carbon-in-Leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. CIL process is becoming attractive even in other situations when preg robbing is not a factor. This paper discusses the situations in which the CIL circuit can be applied. The results of Leach/CIP and CIL circuits at Newmont's Mill No.2, 4 and 5 are presented for comparison. Newmont's Mill No. 4 was initially designed for a throughput of 4500 tons per day. The mill is presently operating at an average throughput of 7300 tons per day without significant changes to the original design. The design considerations of the Mill No.4 CIL circuit are discussed.

Jan 1, 1991

By J. C. Heter

Industrial Mineral Fillers, LLC. is in the initial stages of mining and processing Anorthosite (CASPAR TM) at its CASPAR mine located in Soledad Canyon, Los Angeles County, California The CASPAR is being mined from the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. Preliminary results suggest that CASPAR is a desirable alternative to silica sand used in construction applications, such as, stucco, grout, abrasives, and other uses including filtration and golf course recreation sands. With the use of standard ore dressing techniques, CASPAR is suitable for use as a filler in paint, plastics and rubber. Environmentally, CASPAR has advantages over silica sand, in that, there is no detectable Free Silca.

Jan 1, 1997

By Jack Parker

Cycles of mine convergence coincide with annual cycles of temperature and humidity in the mine. Laboratory measurements confirm that the presence of moisture reduces rock strength and induces internal rock stress. Findings are used in the design of mine openings.

Jan 1, 1969

By V 9. 0 / 300 dpi

In the time period from the early 1980's to the present, longwall roof support technology has evolved tremendously. Chock supports and caliper shields were replaced by 2-leg or 4-leg lemniscate shields. The lemniscate linkage for which the support is named offers numerous advantages to the sup-port both as a fabricated structure and to its performance in the mining application. The hydraulic system, which is the dynamic element of the roof support, was essentially unchanged in early lemniscate shields with the exception of the complexity of additional hydraulic circuits to power a canopy tilt cylinder and canopy side-seals. The control of these fluid-powered functions was provided by direct manual control of valves energizing individual functions onboard the roof-support or the adjacent roof-support. This control valve-gear was comprised of multiple individual valves arranged in a "bank" or integrated into a single hydraulic distribution block with a single operating handle to select any independent function.

Jan 1, 1993

By Bianca Cruz, Tom Lankiewicz, Kent Sorenson, Karrie Radloff, Elizabeth Deyett, Dayal Saran, Michaeline Albright, Dan Stigers

Biology opens a new frontier for the mining industry. With rising environmental concerns, the need to couple conventional chemical and physical technologies with sustainable approaches is pressing. At Allonnia, we harness microbial processes to create innovative and environmentally responsible technologies with broad applications. The native microbial community (microbiome) remains largely unexplored at most mining sites, unlike the geochemical environment. The exploration of complex biological reactions that could transform mining technology is just starting and holds vast possibilities, spanning bio-cementation, carbon sequestration, ore beneficiation, water mitigation, bioleaching, metals recovery, and more. Allonnia has collected samples from mine sites in Australia, Africa, and North America to characterize the microbiome and uncover the genetic potential present in mineral-rich environments. We are evaluating microbial metabolites that selectively solubilize gangue from various ores. In addition, biological reactions hold promise as tailings stabilizers. Our early efforts illustrate exciting prospects for harnessing biology’s potential in mining.

Feb 1, 2024

By W. C. Shanks

The Pioche District of Lincoln County in southeastern Nevada (Figures 1 and 2) has been an historically important producer of silver, zinc, and lead. Economic geology of districts in the Pioche area is summarized most adequately in recent reports by Tschanz and Pampeyan (1) and Gemmill (2) and only a few major aspects will be discussed here. Production in the Pioche District began in 1869 and early mining concentrated on silver-bearing fissures in lower Cambrian quartzites. In the early 1870's the Pioche District was second only to the Comstock Lode in world silver production (3). More recent mining activities have centered on the other major ore type in the area, bedded replacement of lower Cambrian carbonates by Ag-Zn-Pb sulfide ore. Production of replacement ore peaked around 1950. The present study is focused on the Pan American Mine because it is an excellent example of low grade carbonate replacement deposits, because there is little structural dismemberment, and because access was readily available. Most previous workers have suggested that both the fissure vein deposits and the bedded replacement deposits of the Pioche districts are a result of spatially related Laramide igneous activity. The purpose of this study is to determine whether ore genesis is a result of igneous activity or if mineralization might be related to late diagenetic processes such as formed Mississippi Valley "type" deposits. Stable isotopes of sulfur, carbon, and oxygen in ore and gangue minerals have been studied to determine the probable isotopic composition of the ore fluid and paleomagnetic studies of the carbonate rocks have been utilized to determine timing of mineralization. Additionally, petrographic and field studies of carbonate lithologies were undertaken in an attempt to delineate non-structural controls on ore localization. These studies are still proceeding and the results presented herein are, therefore, preliminary in nature.

Jan 1, 1979

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology to support Industry 4.0 has become the target of academic research in many sectors. This study reviews the trends of open-source technology, its forms, and some industrial applications. As a case study of the use of open-source hardware and software in the mining industry, this study proposed a low-cost environmental monitoring system for nonmetallic underground mines to support mine safety and occupational health. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device, and open-source software, MIT App Inventor, to develop an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a nonmetallic underground mining site to assess the performance of the system in mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors.

By A. Jennings, J. Cornet, P. Perrone

Controlling long overland conveyors with multiple drive stations is a complex problem. The methods for controlling these belts in a steady state are well-covered in existing literature, but a discussion of starting and stopping strategies is absent. This paper outlines different control strategies for starting, stopping and running conveyors with multiple drive stations. To illustrate the benefits of applying the methods described in this paper, the authors show how their adoption corrected many of the control system problems at Essroc Cement’s overland conveyor, which features three drive stations separated from each other by long lengths of continuous conveyor belt.

Jan 1, 2013

By Theodore Triplett

To assess the value of various subsidence mitigation techniques, twelve linear foundations were constructed above a longwall mine. The structures were monitored during and after undermining, and footing curvatures at the time of cracking were compared with predicted values. An unreinforced concrete footing sustained substantial damage. Other footings received varying degrees of damage, with inclusion of a sand layer significantly affecting performance. A post-tensioned concrete foundation suffered minimal cracking. Also, a technique developed by the Bureau of Mines is presented for determining the subsidence, slope, curvature and strain of the ground surface.

Jan 1, 1986