Search Documents

By R. Kalra

The current paper looks at evaluating the merits of large geared mills versus gearless driven mills by evaluating the following factors: The capability of currently available systems in terms of power and mill diameter Efficiency in terms of overall electrical power consumed vs mechanical output power Capital cost Running costs Cooling requirements in terms of air versus water cooling Installation and delivery time World?s largest geared drive ? 2x8500kW ? Wushan, China (operating) Among the many reasons that geared drives on large SAG mills are not favoured, is due to not having an efficient variable speed drive option (60 to 80% critical speed), which is required for process reasons. As technological advances have occurred quite rapidly in recent years, this paper uses the latest data in applying these comparisons and attempts to dispel some of the myths regarding Slip Energy Recovery (SER) and variable frequency drive technology on twin pinion drive systems. Early attempts to provide load sharing on twin pinion drives used primitive electronics which have since been developed to eliminate the problems encountered in earlier attempts. In particular, torque pulsations between the twin motors have been overcome using a higher number of devices (pulses) and better electronics. With successful operation of 2 x 6.5MW (Phu Kham, Laos) and three 2 x 7MW units under manufacture (Pascu Lama) and a further 40 projects worldwide, energy efficient Hyper Synchronous SER drives are now mature and ready for use on 2 X 10MW dual drive mills. Speed variation required is in the range of +/- 15% of synchronous motor speeds. VVVF drive packages from ABB and Siemens are also available for 2 x 10MW in low and high speed options. Dual hydraulic inching drives provide a much safer and convenient operation with the added advantage of locked charge detection.

Feb 27, 2013

By E. K. Albert

In 1977, Congress enacted Title IV of the Surface Mining Control and Reclamation Act (SMCRA), providing for an "abandoned ml.ne reclamation fund". This fund, taken from a fee collected from operating coal mines, provides capital for the reclamation process. However, given the number and extent of abandoned mine sites in some states, the question of project selection is important. This paper describes a project in progress to create a Management Information System application for project ranking under multiple objectives. The benefit of this project for the need of new environmental control technologies will be discussed.

Jan 1, 1990

By Daniel Hodouin

Artificial neural networks (ANN) are of growing interest in a wide variety of applications. Pattern recognition, speech processing, financial analysis, signal processing and process control are at present the most successful ones. This paper is an attempt to illustrate the potentiality of ANN applied to mineral processing. An introduction to the technology of ANN is first proposed to describe the various components and to explain the various phases encountered in setting up a network. Then examples are given to illustrate the use of ANN dynamic modelling of mineral processing units or plants and in process control.

Jan 1, 1991

By Harry M. Conger

Kaiser Steel Corporation's Eagle Mountain Mine is located in the Colorado Desert, 60 miles east of Indio, California. Concentrates from the mine are shipped by rail 164 miles to the company's steel mill at Fontana, and also to Longbeach, California for export. Temperatures are typical of the lower desert ranging from a high of 120 degrees in the summer to a low of 25 degrees in the winter. The average annual rainfall of about two inches comes mainly as cloud bursts during the summer months. From its inception, the Eagle Mountain Mine has had the problem of breaking its mine rock. Practices followed from 1949 until 1962 were very costly, did not produce uniformly good fragmentation, and were incapable of sustaining high production. During this period, every conventional type of explosive then in use was tried and found to be unsatisfactory for one reason or another. The first slurry test work at Eagle Mountain was started in 195E and finally by 1962, after having tried all the slurry mixtures then available including some "home made" formulas, a metallized slurry was perfected at the mine which overcame all of the disadvantages of former blasting methods.

Jan 1, 1965

By William J. Miles

The inhalation of dust has been a problem in the mining industry since antiquity. Crystalline silica is now known to be the cause of silicosis, a form of pneumoconiosis that is associated with excessive exposure to respirable particles in some mining and industrial environments. Crystalline silica was reviewed by the International Agency for Research on Cancer (IARC) in 1986 and classified as a Group 2A, Probably Carcinogenic to Humans in Volume 42 and Supplement 7 of the IARC Monographs (1987). In 1996, IARC reviewed additional literature and studies published in the intervening decade and recommended that quartz and cristobalite, two polymorphs of crystalline silica, be listed as Group 1, Carcinogenic to Humans. Their recommendations and reclassification were published in 1997 in IARC Monographs 68.[2] In both Monographs, IARC classified amorphous silicas as Group 3, Inadequate Evidence for Carcinogenicity to Humans.

Jan 1, 1998

By James M. Barker

Marketing is the linchpin of the industrial-mineral (IM) industry. Without markets and consumers for IM products, all other associated IM activities are superfluous. The simple existence of an IM deposit does not mean that it can be exploited. A dynamic interaction between exploration (geology), mining, processing, transport, marketing, sales, and consumers is required for profits. Geology dictates the existence of a deposit, but markets dictate its development, and transportation provides the connection. This is true to such an extent that marketing commonly is called the exploration phase of IMs. Marketing is strategic and includes long-range market-development and planning activities, whereas selling is tactical and more focused on day-to-day consumer interactions. Each will help the other when properly done. Many producers of IMs have failed because of inadequate marketing skill, information, and practice. Over many years at the Montana Bureau of Mines, the many developers seeking technical assistance to find an IM deposit, but who had no marketing plan, always failed. In contrast, the few who sought assistance first on marketing, with the IM deposit to be found later, always succeeded (Richard Berg, personal communication, 1998). Marketing has many facets helped by geologists who must be aware of what marketing is attempting to do. A geologist needs to understand many aspects of IMs: location (deposits, plants, consumers), processing (specifications), transportation (truck, rail, barge, ship), competition (local, regional, national, international), substitutes, pricing, and new developments and market forces of all kinds. Some needed skills are not taught formally to geologists, so well-rounded self-education and on-the-job training are the way a geologist normally enters into IM marketing. The IM geologist generally is associated with marketing either by helping to prepare a market study or by acting on the results of one. Preparing a market study is a two-part process. The first part is relatively simple but requires a time-consuming collation of data into an IM survey (mostly past-and present-oriented). The more difficult and much more important second part entails expanding the IM survey into a market evaluation (mainly future-oriented) that emphasizes forecasting, timing, location, and specific products. A market evaluation generally boils down to formulating the right questions to ask of the right persons. One very good question to ask is, "What could be the market for this specific IM?" while thinking for yourself without excessive recourse to gossip, rumors, promoters, developers, or (at times) IM experts. The evaluation must prove that market potential exists and suggests a marketing plan. Effective marketing is an ongoing process, with the initial marketing plan modified over time, using wide and continuous input to avoid tunnel vision. Industrial-mineral markets are based either on commodity (lower-priced, basic-processing) minerals or specialty (higher-priced, value-added) minerals. IM marketing methods are either product-driven (commodity minerals), a more traditional approach, or market-driven (specialty minerals), but these are neither mutually exclusive nor is one always better than the other. Focusing too much on specialty minerals can lead to problems. A blend of commodity products with specialty products commonly lowers risk and enhances long-term profits. The highest profits occur in specialty minerals at the cost of higher risk and complexity and require intelligent marketing, versatile technical services, and creative research and development. Industrial minerals are best served by an industrial-marketing approach rather than a consumer approach. Modern industrial marketing emphasizes the consumer using the "marketing concept." The marketing concept focuses all management and operational activities on total consumer management and satisfaction similar to the total quality management approaches to excellence.

Jan 1, 1999

By MEHMET ALI RECAI ONAL, MAHMUT CAMALAN

The key motivation of this study is to evaluate the potential of well-known hazardous gases—carbon dioxide (CO2), hydrogen (H2) and oxygen (O2)—as grinding aids for mineral liberation in ball milling. The results show that exposure of chromite ore particles to CO2 flow will promote chromite liberation at breakage and, therefore, using CO2 as a grinding aid may partially reduce the carbon footprint of the mining industry. For that purpose, the use of two-phase (gas–solid) or three-phase (gas–solid–water) moving-bed mixers are recommended for the pretreatment of mill feed before ball milling.

By Carl G. Schwenk

Rusk County is located in the northwestern portion of the state of Wisconsin, roughly 130 miles east of Minneapolis (Figure 1). The topography is generally flat with dairy farming the principal activity. Forest and swamp lands are common, as well as pasture and cultivated ground. Rusk County falls near the southern terminus of the Precambrian Shield and is covered by a thick layer of glacial drift. Outcrops are quite rare, but the few available exposures indicate that the subsurface is comprised of steeply dipping metamorphosed volcanics and sediments of Early Proterozoic age. A thin section of flatlying Cambrian sandstone is sometimes found directly under the glacial till. The depth to Precambrian basement has been recorded to be as great as 150 feet beneath the surface.

Jan 1, 1976

By Irvine G. Reilly

Results of a preliminary study of the ammoniacal leaching of covellite (CuS) in an aqueous oxidizing system in the presence of a non-miscible organic sulfur solvent are described. Up to 60% of the sulfur can be recovered from the solvent as elemental sulfur 1 while achieving high degrees of solubilization of the mineral. The effects of temperature, particle size, oxygen pressure, ammonia concentration and ammonium ion concentration on the degree of sulfur recovery were investigated. Maximum recoveries were achieved at moderate temperatures and in well-buffered systems, with a large excess ammonia concentration. Oxygen pressure and particle size were found to have little effect on fractional recovery of sulfur. A simple empirical model based on electrochemical theory correlating the effects of some of the parameters cont-rolling the degree of sulfur recovery is presented. The results of this work also confirm that in any proposed reaction mechanism for the oxidative ammoniacal leaching of copper sulfides, the primary oxidation product of the sulfide ion in elemental sulfur.

Jan 1, 1978

By Thomas A. Gray

The Dolph Mine fire site is located in Lackawanna County, PA, approximately three miles northeast of the city of Scranton. The fire was burning in both coal refuse (culm) and underground anthracite mine workings. It was reportedly begun by rubbish burning on top of a culm bank. A site investigation was completed in 2006 to define the extent of the fire and to recommend fire control measures. A cut off trench was selected as the principal control method. Plans and specifications were prepared in late 2006. The project was bid and a contractor selected in early 2007. The trench construction was completed in 2007. This paper describes the investigation and selection of the fire control method and discusses the trench construction.

Jan 1, 2009

By J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is n practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota (a) must be covered with about 70 cm of soil material to achieve maximum production; (b) topsoil must be segregated and spread separately from subsoil; (c) potential production depends on the quality of the soil material returned; and (d) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation. Almost half the nation's cool reserves are in the Northern Great Plains underlying several million hectares of agricultural land. Social pressures to return mined land to agriculture or other productive uses have resulted in recent enactment of state and federal legislation, which is intended to restore productivity to disturbed areas. All such legislation relating to the Northern Great Plains has stipulated that useable soil material be saved and returned to mined land after spoils are smoothed. This requirement immediately raises questions as to how much soil material is needed, what criteria are important in defining useable soil material, how is the soil material to be handled in the earth-moving operations involved, and how can replaced soil material be maintained and revegetation. Scientists at the USDA Northern Great Plains Research Center at Mandan, North Dakota have conducted research on the reclamation of disturbed lands since 1970. Initially this research was designed to identify and characterize those physical and chemical properties of spoils that are most restrictive to plant growth (1). Basically, they found that any properties of spoils that reduced the efficiency of storage and utilization of the limited precipitation received adversely affected plant growth. Thus, in the Northern Plains, revegetation of mined land was found to depend upon the management of factors affecting the availability of water to plants - the same as on unmined land. After the major problems in revegetation were identified, technologies were developed to circumvent the effects of the growth-limiting factors (2). Basically two approaches were identified by which plant growth-restricting properties of spoils could be corrected: (a) various amendments (gypsum, sulfur, Fertilizers, mulches, calcium chloride, etc.) could be applied to spoils to improve their ability to conserve precipitation and provide water for plant growth; or (b) undesirable spoils could be covered with suitable soil materials to reduce or alleviate adverse effects. The latter approach appeared to be more feasible in most instances And is the approach specified in current legislation. The remainder of this paper discusses research on the use of roil materials returned to spoils and summarizes the information obtained.

Jan 1, 1978

By C. W. Lockhart

Strength evaluation programs, based on sub- jecting a number of 5-718 inch (0.15 m) diameter core samples from highly fractured or poorly consolidated rock, to triaxial compression tests, have been successfully completed. An innovative approach was required since con- ventional methods with similar materials had not produced reliable results. Drilling methods were modified, and specially designed transparent core barrels were used. Sample preparation was successfully accomplished by using speciallydesignedtools and unorthodox hand- ling methods. Initial tests were carried out on weathered oxides from an open pit copper mine. The technique was later used successfully where the test material was weak, friable coal. The procedures used offer a practical method of testing weak materials where conventional methods would not be successful.

Jan 1, 1980

By H. Yen, D. E. Walsh, H. K. Lin

"Comminution circuits are widely used in nonferrous and precious metals milling. Steel crushers, grinding mills and grinding media are typically used in comminution circuits. Comminution circuit wear products, in the form of metallic iron (steel) fines, are unavoidably produced and report to undersize products in the classification circuit, i.e., flotation or leach feed, while tramp grinding steel (TGS) reports to classification oversize products and returns to the grinding mill, building up in the circulating load. In laboratory studies, TGS reduced grinding efficiency significantly, the impact being dependent upon the size of the TGS present in the mill. Because iron fines adsorb flotation reagents effectively, iron fines increase reagent consumption and reduce flotation recovery. Iron fines are also capable of reducing gold recovery in cyanidation circuits via a cementation reaction. When using filtered gold solution from the cyanidation circuit of an Alaskan gold mine, the gold concentration in solution was reduced by 0.2 to 2.6% over various reaction periods when iron fines were present in the solution.IntroductionComminution circuits are widely used in copper, lead, zinc, nickel, cobalt, molybdenum and precious metal mills. Flotation and leaching processes are usually preceded by comminution (crushing and grinding) circuits in order to liberate valuable minerals for effective separation, concentration or dissolution by the subsequent flotation or leaching processes.Steel crushers, grinding mills and grinding media are typically used in comminution circuits. Comminution circuit wear products, in the form of metallic iron (steel) powder, are unavoidably produced and report to undersize products in the classification circuit (flotation or leach feed), while tramp grinding steel (TGS) reports to oversize productions during classification and returns to the grinding mill, building up in the circulating load. Variables affecting the amount of metallic iron powder and TGS produced in a comminution circuit include ore hardness, grinding mill operating conditions, comminution circuit design and the metallurgy of the steel used for manufacturing crusher liners, mill liners and grinding media. As one example, a comminution circuit product of 80% passing 200 mesh at the Pogo Mine, AK is estimated to contain approximately 2 kg/t of metallic iron. A finer grind will generally produce a comminution circuit product with higher metallic iron fines content."

Jan 1, 2015

By A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By A. D. Davis

A ground-water flow model was developed to simulate the post-mining recharge rate at the Belle Ayr surface coal mine in the Powder River Basin near Gillette, Wyoming. State regulations of Wyoming require that reclaimed lands should provide a rate of recharge that approximates the pre-mining rate. Steady-state calibration and transient simulations showed that the post-mining recharge rate in backfill is at least five centimeters per year, exceeding the original infiltration rate of 0.4 centimeters per year to shallow, overburden aquifers. Major reasons for the increase include the flat topography of reclaimed areas and decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate less than five centimeters per year but somewhat greater than the pre-mining rate.

Jan 1, 1995

By Malcolm T. Wane

The subject matter of this paper, "Applied Rock Mechanics?," has its genesis in a recent field trip taken by the author. A more or less standard question asked at the mines visited was "How are you using the principles of Rock Mechanics to assist you in maintaining an efficient, safe, and competitive mining operation?" The question was couched in a number of different forms, but the intent was to determine whether or not a general theory based on reason and the scientific method was applied or whether the alternatives of tradition, intuition, ?common sense', revelation, ?shotgun methods' or authoritarianism were invoked. Perhaps two responses to this query will be illustrative of the general nature of the replies. At operation XYZ an extension to the known ore body has been found. The extension is of large enough size and grade that a mining scheme using load-haul-damp techniques is envisaged. Since this represents a departure from the present mining scheme, questions have arisen regarding pillar sizes, room and entry sizes and possible support requirements. A task force has been set up to expeditiously plan for these things and write the necessary specifications and requirements. The fundamental question was posed to members of this group.

Jan 1, 1971

By Yehia M. Eyssa

A "straight wire" flow through magnetic ore separator has been designed, built and successfully used to separate magnetite from typical slurries. The purpose of these experiments was to simulate the high field profile of a "straight wire" superconducting magnetic separator which would be capable of separating weakly magnetic hematite ore from typical slurries. Magnetite was used as the test mineral because it experinces the same magnetic forces at low field as does hematite at high field. The present separator concept is based on the fact that there is a particle concentration profile due to the gravity field for low velocity turbulent flow. When a magnetic field force of -g is applied the concentration profile of the magnetic particles will be reversed leaving the nonmagnetic particles flowing alone at the bottom of the channel. By means of a divider at the end of the channel the concentrate is separated from the tailings. It is shown that the time needed to deflect hematite particles in a narrow cylindrical channel concentric with the superconducting wire is small enough so that high throughputs in the turbulent flow region are possible. In the case of a high field superconducting separator the centrifugal force could replace gravity by rotating the flow around the straight wire conductor.

Jan 1, 1974

By James K. Gowans

The Red Dog Operation is located in northwestern Alaska at Latitude 68°, 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The orebody was acquired by the NANA Regional Corporation, (an Alaska Native Corporation established by the Alaska Native Claims Settlement Act of 1971), in 1980 in their land selection. In 1982 Cominco American and the NANA Corporation signed a development agreement and Cominco Alaska Inc., a wholly owned subsidiary of Cominco American, was formed to manage the Red Dog Project. An extensive exploration program in 1980 -1982 outlined a mineral inventory of 85 million tons, at a grade of 5.2% Pb, 17.1 % Zn, and 2.4 oz/ton Ag, which makes the Red Dog the second largest deposit ever discovered. Broken Hill, in Australia, is the only zinc orebody which was originally larger than Red Dog. The design of the facilities is to process 2.1 million tons of ore annually, which will produce 560,000 tons of zinc concentrate, 100,000 tons of lead concentrate and 50,000 tons of bulk lead/zinc concentrate.

Jan 1, 1991

By J. L. Thompson

Lime made in a coal-fired, rotary kiln has two distinct parts: the interior of the pebble which constitutes about 90% to 95% of the mass, and the surface dust layer which is the remaining 5% to 10%. Uncalcined carbonate and impurities in the product may be present and will not contribute to the hydration reaction. Sulfur, in the form of calcium sulfate, inhibits the hydration reaction out of all proportion to its actual weigh-percent concentration (perhaps more than 100 times). If the stone contains dolomite, this will also inhibit the reaction as its rate of hydration may be nearly 3 orders of magnitude slower than that of calcium oxide. Early in the hydration reaction dolomite appears practically inert, but given sufficient time, it will hydrate. The heat of reaction is nearly the same as for calcium oxide, but the time necessary for complete hydration may be hours; whereas for calcium oxide it is only fractions of a second. The dust layer on the surface also inhibits hydration as it contains a collection of compounds which have low heats of hydration. This layer can tie up additional calcium and delay or prevent its reaction. In addition to these chemical processes, an important physical characteristic of the lime is its specific surface area. This is effected by the thermodynamics of calcination and the original stone grain chemistry. All of these factors are agglomerated in the gross slaking rate of lime. The total hydration of the chemical complex that is called commercial lime can be more easily understood by considering the individual reactions and combining them to form a more comprehensive picture of the situation. Calcium oxide and magnesium oxide hydrate similarly, differing only in their reaction kinetics. Dolomite, however, reacts differently than a simple mixture of calcium oxide and magnesium oxide as its hydration is strongly influenced by calcination thermo-dynamics and stone grain structure. Finally, the dust hydration and composition should be examined Understanding these reactions enables one to examine hydration reaction graphs with more insight into the factors which determine their shape.

Jan 1, 1978

Room-and-pillar mining at White Pine started in 1953 from a sub-outcropping orebody that gently dips to 1000 m depths in a distance of about 6 km. High horizontal stresses were recognized in the mid-1960s which had obvious stability impacts when viewed in combination with the increased overburden stresses. Modifications in conventional room-and-pillar design were introduced through the years on a trial-and-error basis to help overcome stability and resource recovery problems. These modifications were based on pressure arch concepts using pillar yielding and/or pillar recovery, and on mine layout orientation to minimize stress impacts. While some of these modifications were successfully applied in some areas, they failed in others. Through the years, visual observations played a major role in panel design with contributions from stress measurements and analyses. However, the down slide in the copper economy during the 1970s and early 1980s resulted in a loss of interest in the application of these concepts. This paper reviews ground control problems and presents the results of recent stress measurements and computer analyses. They shed light on the importance of using yield pillars and mine layout orientation to control stresses at depth.

Jan 1, 1993