Search Documents

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

During the past 15 years, roof fall rates have fallen dramatically in US coal mines, particularly in regions where the roof is weakest. The remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present a design methodology that builds on and quantifies the basic roof support concepts that have been successful in the USA. The methodology starts by defining three modes of roof support, based on the roof strength relative to the stress level: (1) suspension, where roof bolts mainly provide skin control for strong roof; (2) beam building, where moderate strength roof can be supported by roof bolts alone; and (3) supplemental support for weak roof. Next, a large database of roof fall histories at a number of mines is used to define the approximate boundaries of these three regimes based on the coal mine roof rating and the depth of cover. Finally, guidelines are presented for site-specific design of support systems within each regime. The new computer package, analysis of mine roof support (AMRS), implements the design methodology.

Sep 29, 2020

By Richard Klimpel

The influence of selective chemical dispersants on the hydrocycloning of a copper ore slurry is illustrated. In the % solids and slurry feed rate ranges associated with industrial practice, desirable changes in both d50 and Sharpness Index values of classification were measured with the use of chemical as compared to tests with no chemical usage.

Jan 1, 1981

By Mohan Dutt

This paper is concerned with applied platinum resistance thermometry which involves many considerations absent in precision thermometry. The historical development of the Callendar-Van Dusen Equation which describes the resistance- temperature relation of pure platinum is discussed. The advantage of using platinum resistance temperature sensors over thermocouples is described, and the improvements in design and construction of these sensors that have come about in the past few years are discussed. Integral and remote bridges that convert resistance changes into voltage together with signal conditioning techniques and equipment for voltage or current signals are described. Errors encountered in temperature measuring schemes and methods to reduce these errors are summarized.

Jan 1, 1969

By V. Dentoni

The paper deals with the assessment of the visual impact generated by surface mining and quarrying. Previous research works proved the applicability of an indirect method based on the elaboration of digital images through which the extent of the visible altered area and the chromatic contrast with the surrounding environment is calculated. The resulting level of visual impact allows an objective comparison among different cases as far as the evaluation procedure is univocally defined. The article illustrates the application of the method to a number of selected quarries located within the Sardinian territory; different issues are discussed such as the choice of the viewpoints from which the pictures are taken, the influence of the distance from the quarry to the selected viewpoints, the light condition and the orientation of the quarry faces. Moreover, the visual impact level obtained from pictures taken at the same time with five digital cameras are compared in order to evaluate the contribution on the overall uncertainty.

Jan 1, 2008

By H. S. Ten Eyck

The major underlying threat to man's successful survival and happy existence on this planet is our own prolification. This poses an even greater threat to the future of civilization than continued wars and even "The Bomb" itself. Just the predictions of the world's population trend are awesome and demand our serious thought. This trend has been given the now well-known term, "The Population Explosion" - and this is literally what is taking place throughout most of the countries around the globe. Today, the world's resources support approximately 3.3 billion people. Based on the present world population growth rate of 2.1 percent, there will be another 65, million just one year from today. Such an increase in one year means that the world will add a greater population than that of Mexico and Canada combined. Projecting at this remarkable, but unchecked, growth rate, 6.7 billion people will be competing for survival by the end of this century.

Jan 1, 1966

By W. E. Sabina

In the short period of one mans? career we have seen specifications for bulk material handling systems and equipment grow from two or three pages to as much as two or three volumes for a single contract. The old 'short form' described what the purchaser expected the equipment to do. The long form does the same but also includes nut, bolt, and lockwasher depth of detail. What are the events that led to this proliferation of verbiage, and does it benefit the buyer in the final analysis? Is there a better way to purchase complex equipment while ensuring the highest quality for the dollar spent?

Jan 1, 1986

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

A numerical investigation of the effect of pore pressure regime on the safety factor and the critical failure mechanism is presented for fly ash storage facility. Pore pressures’ measurements from standpipe piezometers and pore pressure estimated from seepage analysis are used to compare the factor of safety for a fly ash slope. This was applied for considering static and seismic scenarios. A probabilistic approach was applied to account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation. Slope stability analysis is conducted in two and three dimensions, adopting the limit equilibrium analysis approach, and also a finite element seepage analysis, to assess the stability of the slope. The two-dimensional cross-sections were extruded to three-dimensional models to estimate the factor of safety and associated shear failure. The results from the performed analysis suggest an increase in safety factor values of 5%.

Mar 27, 2024

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

By Dirk van Zyl

It can systematically assess if the control and management systems designed for protection of sensitive ecosystems are adequate. The results of the assessment can help to identify key elements in the project that pose higher risks due to uncertainties in design. These assessments can then be used to make recommendations to further manage and reduce risks as the project is developed. QUALITATIVE RISK ASSESSMENT The general principles of a risk assessment are well summarized by Kaplan and Garrick (1981): "In analyzing risk we are attempting to envision how the future will turn out if we undertake a certain course of action (or inaction)." Fundamentally, therefore a risk analysis consists of an answer to the following three questions: What can happen? (i.e. what can go wrong?) How likely is it that that will happen? If it does happen what are the consequences?" Risk assessments can be performed using various levels of sophistication depending on the amount and accuracy of data available. A qualitative risk assessment uses descriptors throughout to express the level of risk. The definitions of the descriptors are presented in terms of the magnitude or concentration of contaminants. The results of a qualitative risk assessment can be used to: a)Document the evaluation and decisionmaking process. Although differences of opinion may exist about the definitions of the descriptors, the process is well-documented; b)Express the relative risk associated with specific activities or design elements; and, c)Select those failure modes or release mechanisms that may result in significant risks. These mechanisms can then be further developed in quantitative risk assessments. A qualitative risk assessment can be performed in a systematic approach using four steps (Van Zyl, 1987): A qualitative environmental risk assessment can be used to describe the risks associated with the development of a new mine and to make an evaluation of the adequacy of its design for environmental protection. The relative magnitude of risk associated with selected failure modes and exposure/consequence scenario assessments is the final result of a qualitative risk assessment. These failure modes are based on site specific areas and components, and mining and construction phases. The four steps of a risk assessment (hazard assessment, exposure assessment, consequence assessment, and risk characterization) are used in the development of a qualitative risk assessment. Relative magnitudes (using a five point scale of negligible to high) for each step, can be quantified in a qualitative risk assessment. Development of the descriptors for the relative magnitudes in each step is a very important part of a qualitative risk assessment. The success of a qualitative risk assessment depends on the adequacy of the information base and the subjective judgements made in each step. The quality of the risk assessment is, therefore, dependent on the experience of the assessors. A mining project in a sensitive coastal environment is presented as an example to demonstrate the application of a qualitative risk assessment. INTRODUCTION Environmental impacts from mining operations have been a significant factor in the last century. This was especially the case prior to the development of a better understanding of environmental processes and the potential impacts of acid rock drainage (ARD), and associated heavy metals, or the uncontrolled disposal of tailings and waste rock (Smith, 1987). Much care has been exercised over the last two decades in designing and operating mines to limit the environmental impacts as far as possible. All new mines are specifically designed with mitigative methods to manage such potential environmental impacts. Attention is directed to ARD impacts, safe disposal of mine waste rock and tailings, transportation and storage of chemicals and fuels, and final reclamation. A qualitative risk assessment can be used to address all project systems and activities that may potentially pose a risk to the environment.

Jan 1, 1992

By John S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7m diameter primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1984

By M. Li, J. D. Miller

During the past decade, considerable effort has been made to develop improved flotation strategies for the sedimentary phosphate resources from Florida, particularly the dolomitic phosphate resources. New flotation equipment and alternate flotation strategies have been evaluated. These developments are reviewed for both traditional siliceous resources and future dolomitic resources. Most process strategies involve variation in the reagent sequence and/or the use of depressants/dispersants. Further research and development efforts in flotation technology are needed to increase flotation plant capacity by elimination of the conventional double float process, to improve the recovery of coarse phosphate, and to achieve the desired selectivity with respect to carbonate minerals, particularly dolomite.

Jan 1, 2000

By C. Cassios

EIA is a procedure aiming the elimination of adverse impacts to the environment from undertaken projects. Historically, it starts in 1969 when NEPA (Nat.Env.Prot.Agency) in the US initiated the EIA ? EIStatement. The EIA procedure was adapted by the European Union with the directive 337/85 and in Greece the Common Ministerial Decision 69269/90 enforced it to the Greek legislation. However, mining enterprises in Greece long before the implementation of the European Directive and in accordance to the legislation of the Public Law 998/79 for the protection of the forested lands were obliged to submit EIA?s and get an approval in order to operate in forested areas. The submitted and approved EIA?s and their implementation by the mining companies were among the positive aspects of the EIA procedures. This paper is examining the impacts of EIA?s in the Greek mining industry its positive aspects as well as their difficulties and their role for the reclamation procedure. The technical and procedural aspects which EIA presents for the mining industry are commented, while proposals, for a more flexible EIA implementation for the Greek Environment are also presented.

Jan 1, 2002

By D. Sotiropoulos

In the recent years, the mining sector is looking for specific indices, taking into account economic, environmental and social criteria, in order to meet the sustainable development requirements. In the present study traditional and environmental sustainable indices used in the Agios Dimitrios Power Plant, Northern Greece, are compared to those of ESKOM Company, South Africa, taken as reference. These indices are referred to, a) the solid fuels consumption, such as lignite, and, b) the emissions to the atmosphere, such as SO2, NO2 and dust. Last five years data show a remarkable improvement of all indices in the Agios Dimitrios Power Plant. Although the lignite used in this Power Plant is by far of poorer quality than that used by ESKOM - net calorific value 1272 and 4638 kcal/kg, respectively - dust emissions in both Power Plants are similar (52 and 31 g/kWh, respectively). The SO2 and NO2 emissions are very low in Agios Dimitrios compared to those of South Africa, respectively 1.92 and 7.91, and 1.74 and 3.61 g/kWh. This is mainly due to natural desulfurization (by the lignite?s calcium content) and the low NOx burners.

Jan 1, 2003

By J. D. Scott

This paper consists of a review of the development and application of spherical charge blasting at Inco Metals Company. Topics will include the Livingston Strain Equation, the field data required for its use in full scale operation, the type of ground in which mining has been carried out, explosives in use and their characteristics and finally, an overview of actual production applications. These applications include Primary Stope Mining, Secondary Mining Against Fill, Mining a Faulted Ore Zone and Drop Raise Blasting. INTRODUCTION Crater blasting in itself has been in use for over twenty years, but only recently has the technique been combined with a spherical size charge to form the Vertical Retreat Mining Method. This article endeavours to put the Livingston Strain Equation in a practical light, to describe several actual hard rock applications, and the results achieved in each case. THE LIVINGSTON STRAIN ENERGY EQUATION C.W. Livingston put forward the following equation as a standard means of determining the optimum burden required for full crater production blasting. The constant "E" is included in an attempt to recognize secondary breakage caused by strain waves.

Jan 1, 1981

By N. R. Billette

In 1982 and 1983, a study was undertaken to analyse the applicability of Elbrond?s analytical model to suit the needs of Lake Asbestos of Quebec in their computerized open pit planning and scheduling strategy. The immediate goal was the assessment of the optimal allocation of trucks and the determination of the extra cost of in-pit blending. Data from 45 tonne trucks was used to estimate the mine capacity based on a fixed assignment policy. The tonnage yielded by the analytical model was compared with the results of a simulation program. Another point that the study high- lighted was the definition of efficiency parameters for the haulage system: shovels-trucks-crusher. The efficiency, both of the utilization of financial resources and of the operations, for the overall system reaches optimal values in very precise conditions for the number of pieces of equipment in operation. Such a parameter is proposed as a standard for the definition of an optimal number of trucks and shovels in operation. Deviations from this optimum do occur in a well-planned system for qualitative goals. These can then be quantified in terms of costs to the mining company.

Jan 1, 1986

By E. H. Bentzen

The purpose of this paper is to explain the production of sand for glass manufacturing and the reasoning behind the sand specifications set by the glass industry. In order to discuss the production of glass sand, there is a need to understand what glass is and how it is made. Therefore this paper discusses glass, as well as sand beneficiation.

Jan 1, 1977

By Ross K. Digby

The Victorian Tunnelling Centre (VTC) has evolved its purpose from purely training workers, to a tunnelling industry education city. The VTC has now focused its activities on the areas of technology; education and training; applied research; and career education. were identied as the hus around which activities would e conducted to create a tunnelling industry education city. The VTC provides ustralias tunnelling industry with an education facility that not only provides laour training, ut enales the industry to come together to meet, participate in product launches, undertake research, work with new technologies and promote tunnelling careers.

Jun 23, 2024

By Josiah Pohl, Christopher Utter, Kyle Everly, Akshay Chowdu

Battery Electric Vehicles offer increased energy efficiency for open-pit load & haul operations at a potentially lower overall carbon cost. Electrifying a mine’s fleet, however, presents a unique set of operational challenges. In this study, we explore the effects of electrification on productivity at real operations using a Discrete Event Simulator. The model can simulate multiple shifts, a mixed fleet of diesel and electric trucks, charging and refueling stations, trolley systems, and accurate shovel-truck loading cycles. This study helps determine the trade-offs of adopting electric fleets and how they interact with the layout of today's mines.

Jun 25, 2023

By I. Melik-Gaykazov, N. N. Melnikov, V. A. Fokin, S. P. Reshetnyak

Kola Mining Institute has been carrying out investigations of the possibility to steepen the walls of the Kovdor open pit with the design depth of 600 m. Steeping (up to 60°) wall angles is done by double height (24 and 30 m) benches with vertical slopes. One of the safety factors of mining with such walls is choosing the width of the safety berms preventing against rock falling from the slopes into the pit working area. The test on rock falling from 24 m benches has shown that vertical slopes are not more dangerous compared to the inclined(60-75°) ones.

Jan 1, 2003