Search Documents

By P. B. Marchant

Bioleach testing and piloting was conducted on refractory gold sulphide concentrate from Austin Gold Venture in Nevada during 1988. The objective of the test programme was to determine the technical and commercial viability of bioleaching as a concentrate pretreatment step prior to gold extraction by cyanidation as an alternative to shipping concentrate to the smelter. Baseline CIL cyanidation typically resulted in < 20% gold extraction from the Austin concentrate. Bioleaching enhanced gold extraction up to 95% using conventional CIL techniques. This paper summarizes the bioleach test programme and results, including pilot plant studies onsite, and describes aspects of the commercial design for a possible retrofit of the Austin flotation tailings leach circuit to accommodate 20 tpd and 40 tpd capacity concentrate bioleach facilities.

Jan 1, 1989

In phosphate flotation, more than 90% of the finer fraction (-35, + 150 mesh) is recovered as opposed to 70% of the coarser material (-16, + 35 mesh). On the other hand, coarser fraction is higher in phosphate content than the finer feed. Consequently, improvement in the coarse recovery is highly desired. It was determined on bench scale that emulsification of the collector (fuel oil and fatty acid mixture) can lead to enhanced recovery of coarse particles. Flotation of phosphate with emulsified collector resulted in improved recovery and grade also on the plant scale.

Jan 1, 1992

By John Cline

The economic value of calcium carbonate when used as an extender or filler basically falls into two categories: 1. Lessening the cost of the final product to which it is added. 2. Contributing desirable physicals to the final product. In most instances, a combination of these two may be achieved. The mineral limestone which is found in abundant quantities in many areas of the world is the source of 99% (+) of the calcium carbonate used as fillers and extenders. Precipitated, or chemically formed, calcium carbonate is also available, but by comparison, in very limited quantities.

Jan 1, 1985

By Richard J. Stoehr

Man has mined in all his time on earth about 3 billion ounces of gold. About one-half of this has been mined in the past 35 years. This gold is roughly in 3 large holdings: one-third held as reserves in Central Banks; one-third held as personal reserves; and one-third is in jewelry or other fabricated products. The world per capita availability of mined gold is increasing and there are many factors and forces shaping gold&apos;s future. Currently, gold has a favorable exchange ratio and this is encouraging many new gold-mining developments. Production is increasing and new techniques are surfacing. The use of gold in the financial markets is increasing in some unique ways and gold is again fulfilling its role as a universal money, making gold&apos;s future predictable. Currently, man is mining gold at the rate of approximately 44 million ounces annually and is therefore adding to the total supply of gold approximately 1.5% of newly mined gold each year. This current production plays a small role in the pricing mechanisms since a very large part of the 3 billion ounces mined in all of history is available to the market in one form or another.

Jan 1, 1984

By W. C. Goldberg

This paper presents pit slope monitoring and back-analysis case studies con-ducted to evaluate and, if possible, stabilize slopes at the Berkeley Pit in Butte, MT. Two specific slopes were studied in detail. The first slope was determined to be near limiting equilibrium, as evidenced by its response to the initiation and cessation of mining, while the second failed on three occasions. Back-analysis of the failed slope verified the laboratory-derived geomechanical properties of the earth materials. Early detection of slope movement can show a need to take action, including modifying slope geometry, dewatering if the slope were wet, and/or investigating and implementing artificial supports. Monitoring slope displacements in open-pit mines can supply data for predicting collapses and preventing serious damage, injuries, and/or loss of life.

Jan 1, 1989

By F. G. Miller

To improve coal flotation Bethlehem Steel Corporation&apos;s Research Department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies5 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the bas is for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14M x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level.

Jan 1, 1968

By Ray Soper

Important progress has been made in developing the K-Process as an alternative to cyanide as a method of recovering gold from ores and other materials.

Jan 1, 1998

By David D. Rabb

Leaching or solution mining, a relatively simple and economical process for beneficiating metallic ores, is likely to find increasing application in the treatment of low-grade ores that are impractical to mine by any other means. This process may be carried out in two different ways: 1. Dump leaching, where the ore is moved from its original location to be leached at another site. 2. In situ leaching, where the ore is leached in place by introducing the leach solution at the top, letting it flow down through the ore under gravity, and then recovering it plus the dissolved metals it contains.

Jan 1, 1969

By Frank C. Di Luzio

REMARKS BY FRANK C. DI LUZIO, ASSISTANT SECRETARY OF THE INTERIOR FOR WATER POLLUTION CONTROL, BEFORE THE ANNUAL MEETING OF THE AMERICAN INSTITUTE OF MINING ENGINEERS, NEW YORK CITY, FEBRUARY 25-29, 1968 POLLUTION PROBLEMS AFTER MUNICIPAL-INDUSTRIAL WASTE CONTROL I am happy to have this opportunity to discuss pollution problems related to the mining industry and the role of mining engineers in protecting our environment. Technological Power and Pollution of the Environment The increasing power of technology to destroy and disrupt the natural environment and the ecological systems upon which life depends has reduced man&apos;s margin for error in the use of this power. We must act, therefore, to deter and prevent the occurrence of future ecological disasters such as that caused on the British and French coasts by the sunken oil tanker, the TORREY CANYON, the Clinch River fish kill which occurred when a dam broke and released coal ash from a power plant operation, or that which threatened on the Clark Fork River in Montana when a strike at the Anaconda Copper Company threatened to shut down pollution control activities, thereby endangering fish and plant life on the Clark Fork River with copper waste. In the past, pollution of the environment has tended to be slow. But now, the increased power of technology to damage nature, the loss of in¬sulating space and the compression of time--all reduce our margin for error and the cushion which space and time once provided for our mistakes.

Jan 1, 1968

By Dale E. Hirschfeld

The clays in Eastern Washington occur in a variety of forms and are extracted for uses in Face Brick, paper coatings, and aggregates. Not in large volumes in comparison to other areas, not even from impressive large mines. However, mans utilization of these clays has progressed from historical clay tablets to the present technically oriented manufactured products of today. White Face Brick, perhaps the whitest produced anywhere is the unique product produced by INTERPACE CORPORATION&apos;s Mica Plant from these unusual clays. It is this basic characteristic feature of the clay&apos;s in the Mica area that differentiate them from the other clay&apos;s in this belt. ORIGIN The significant properties of clay&apos;s used in Face Brick are plasticity, fired color, fired strength, dry and fired shrinkage, the PCE or Pyrometeric Cone Equivalent, and extrudability. Testing clay&apos;s for these properties is standard laboratory procedure. No two clays are alike, and seldom can one clay be substituted for another. Mica White Clays respond favorable to all these properties, but more especially, the Mica Clays fire to a brilliant white color, from almost the natural state. The geologic history of Eastern Washington is largely conjectural because of the absence of rocks representing segments of geologic time. The oldest rocks in this area are the argillaceous and arenaceous sedimentary rocks which have been slightly metamorphosed. These rocks have been correlated with the Belt Series of the Pre-Cambrian age, although some may be older. These rocks were subsequently intruded by granadiorites and related rocks that are considered to

Jan 1, 1971

By Richard I. Grass

The White Pine Mine is located 4- 1 /2 miles south of Lake Superior in the western part of Michigan&apos;s Upper Peninsula. The orebody occurs in tabular, gently dipping Keweenawan sediments. GEOLOGY The orebody outcrops beneath 30-50 feet of Pleistocene clays and dips to the east and northeast to a depth of 3, 000 feet in five miles. It lies midway between the Porcupine Mountains and the Bergland Hills, both of which are steeply dipping felsite and coarse porphyry intrusives, extrusives and sediments (Figures 1 and 2). The orebody sediments were deposited in the Keweenawan basin during mid- and upper Keweenawan times. Mineralization occurs in the basal 20 to 25 feet of the Nonesuch formation, which is made up primarily of laminated siltstone s. Native copper, chalcocite, and silver are the ore minerals. The ore is mined by trackless room-and-pillar methods.

Jan 1, 1967

By D. K. Grubbs

Anorthosite is an abundant, domestic source of alumina with reserves in individual deposits ranging from a few billion to hundreds of billions of tons. While anorthosite contains less alumina than does kaolinite, its CaO and Na20 contents are significantly higher (Figure 1). Alumina can be produced from anorthosite by alkaline, soda-lime sinter or acid processes. CaO and Na20 are advantageous because they are reactants consumed in alkaline processes. Acid processes require high calcium plagioclase feldspars (bytownite-anorthite) to obtain high alumina extraction because the lower calcium plagioclase feldspars (andesine-labradorite) are not as readily dissolved during digestion. The layered Raggedy Mountain Gabbro group in the Wichita complex in southwest Oklahoma is a high calcium anorthosite that could be processed by acid, sinter, or alkaline methods. Chemical grade limestone in the Arbuckle Group is located within 45 km of the anorthosite (Figure 2).

Jan 1, 1980

By B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand and gravel (SSG) sector in the United States. Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) are conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine.

By Omar Abd el Fattah Ramly, Abdallah Mohamed Sourour

FOREWORD In 1974, the Ministry of Housing and Reconstruction (The Client) which subsequently became the Ministry of Development and New Communities of the Government of the Arab Republic of Egypt assigned responsibility to the Arab Contractors (Osman Ahmed Osman and Company) for the design and construction of the tunnels under the Suez Canal. For this project the Arab Contractors of Cairo and Tarmac International of London formed a joint Venture, called Osmac. Sir William Halcrow and Partners of London are responsible for the design of the Ahmed Hamdi Tunnel as a Sub-Contractor to the Contractor. The advisory consultant of the client is a joint Venture between Tippetts-Abbett-McCarthy-Stratton (TAMS) of New York and Arab Consulting Engineers (ACE) of Cairo. INTRODUCTION A site investigation was carried out between Km 141 and Km 150 Suez Canal chainage to determine the ground conditions relevant to design and construction of a road tunnel under the Suez Canal. A feasibility study included aerial surveying, geological mapping and the drilling of 8 boreholes. Detailed investigation included the drilling of 105 boreholes, sampling, piezometer installation, pumping tests, and the digging of trial pits and trial excavations. In-situ work comprised SPT, permeability tests and dilatometer tests. Laboratory testing included soil classification tests, compaction tests, California Bearing Ratio tests, shear strength determination and oedometer consolidation tests as well as chemical analysis of both soil and ground water. The investigation revealed that the ground conditions at the first proposed El Shatt site (Km 148.5) were not favourable for bored tunnelling, whereas they were more favourable at the southern El Shatt site (Km 150.0).

Jan 1, 1979

By J. D. Morgan

The US economy grew steadily in 1989, reaching an annual rate of $5.3 trillion in the last quarter (US trillion=1012 ). The value of domestically processed, mineral-based materials rose 5% to $315 billion (US billion=109). The value of metals produced from US ores rose 14% to $11.6 billion, while industrial minerals rose 2% to $20.2 billion. Recycled scrap was valued at $10 billion. Increasing economic activity stimulated metal prices. Yearly lows and highs were $2.31 and $3.56/kg ($1.05 and $1.62 per lb) for copper, $1.58 and $2.57/kg (72 and $1.17 per lb) for aluminum, 77 and 97 cents/kg (35 cents and 44 cents per lb) for lead, and $1.58 and $2.09/kg (72 cents and 95 cents per lb) for zinc. Many mining and metal companies reported reasonable profits. Consumer demand strongly affects mining because the US economy is saturated with long-lived products. Consumer, mortgage, and Federal debt continued to rise. 250 million US citizens already possess 172 million licensed motor vehicles and 100 million dwelling units. New car production fell 4% to 6.8 million units, while truck and bus production fell 1 % to four million units. New housing starts fell 9% to 1.4 million units. Imports supplied a significant proportion of total US consumption of several important mineral materials. Imports of crude and refined petroleum costing $50 billion exceeded domestic crude oil production. President Bush expressed "strong concerns about this country becoming further dependent on foreign oil." And the Department of Energy held a series of hearings around the country to develop ideas for a "national energy strategy."

Jan 1, 1990

By T. B. Jarboe

The 150 MWe circulating fluidized bed (CFB) power plant described in this paper is the product of recent Bechtel experience in the industrial power and steam market, where the economic feasibility of fluidized bed projects has been proven. The inherent ability of CFB boilers to burn low grade fuels makes it possible to also burn low ranking coals or coal wastes, including anthracite culm, coal mine rejects, and coal wash plant waste slurry. The impact of fuel characteristics on plant design is addressed. This includes solids handling, steam generation, sulfur capture, and auxiliary load requirements.

Jan 1, 1988

By L. Patts, J. Hummer

The use of diesel-powered equipment in underground coal mines has increased substantially during the last ten years in an effort to enhance mine safety and productivity. Pennsylvania and West Virginia are two of a number of states with regulations governing the use of such equipment. These states both developed and promulgated regulations before permitting diesel equipment in their underground coal mines because of concern for miners’ safety and health, especially with regard to the contamination of mine ventilation air with diesel exhaust emissions. The major components of diesel exhaust emissions are combustion gases and diesel particulate matter. The gaseous emissions consist of carbon monoxide, carbon dioxide, oxides of nitrogen, sulfur oxides and unburned hydrocarbons. The diesel particulate matter (DPM) is comprised of solid carbon particles, liquid and solid hydrocarbons, sulfates and moisture. The Federal Mine Safety and Health Administration (MSHA) also promulgated regulations in an effort to control diesel emissions in underground coal mines. MSHA has adopted threshold limit values (TLVs) for all gaseous components of diesel exhaust, which were established by the American Conference of Governmental Industrial Hygienists (ACGIH). MSHA (30 CFR Part 72 Subpart D) has established a tailpipe DPM emissions limit of 2.5 g/hr for diesel engines used in permissible equipment, heavy-duty non-permissible equipment, generators and compressors used in underground coal mines. A tailpipe DPM limit of 5.0 g/hr has been established for light-duty outby diesel-powered equipment. The rationale for the tailpipe emissions limit was that an ambient measurement of DPM in a coal mine was not feasible because there is no established sampling method able to distinguish between coal mine dust and DPM. The stringent tailpipe emissions limit mandates the use of exhaust aftertreatment devices for most diesel engines used in underground coal mines today. One method by which tailpipe DPM can be reduced to MSHA limits involves using an exhaust cooling device in conjunction with a high-temperature, disposable diesel particulate filter.

Jan 1, 2011

By K. E. Yassin, A. Yehia, M. Amar

Phosphate ores are the source of many commodities, such as phosphorus element, P2O5 and fertilizers. Discarding a large percentage of fine phosphate particles produced as slimes during phosphate ore processing represents a severe environmental problem, besides making the beneficiation process uneconomical. The phosphate industry is interested in a process that is efficient, with high grade and high recovery; ensures economical feasibility, with low operating cost; and is environmentally sound, with low toxicity. Numerous investigations have been conducted to try to find better processing techniques and reagents. However, reagent requirements and recovery limitations may be so high that the end does not justify the means. Reagents of biological origin are of special interest because they offer specific interactions with minerals, reduced operating costs, environmental acceptability and flexibility in adaptation. Recently, there has been a growing interest in using microorganisms as flocculants for mineral fines and as flotation collectors. 

By Kenneth Savidge

With the recent demand for increased coal production there has been a corresponding increase in the horsepower of the shearing machines. The resultant increase in the machine haulage pull has heightened the incident of haulage chain breakage resulting in machine downtime, but more seriously the danger to face personnel. This paper discusses the application of chainless haulage to longwall mining and describes the systems currently available.

Jan 1, 1978

By B. C. Lewis

When John F. Kennedy made this statement, I am sure he was not thinking about the valuation of limestone reserves. However, it is certainly applicable. The objective of this paper is to demonstrate how the discomfort of thought (i.e., the analytical and methodical process performed by a reputable professional) builds the foundation for an opinion that provides assurance as to the value of a property. In its final form, a valuation is nothing more than an opinion. The credence of that opinion is directly proportional to the knowledge of the appraiser and the efforts and judgment extended in developing said opinion. Presented herein are the methodologies for formulating a defensible opinion. Before detailing the valuation process, an overview of the limestone industry is presented along with some historical parameters relating to the industry. Secondly, the most widely used valuation methodologies and a brief discussion of each are presented. Two case studies are then presented, which review actual valuation studies. The paper concludes with how the valuation process should be published in a report format that is defensible from a legal standpoint, bankable from a financial standpoint, and decipherable from a layman&apos;s standpoint.

Jan 1, 1989