Search Documents

By L. G. Hendrickson

Direct-reduction processes for converting iron ores to metallic iron in the solid state have been available for some time; and whenever scrap becomes expensive, there is a new wave of interest in these processes. It is well established that direct reduction, coupled with electric-furnace steelmaking, is a technically viable method for making steel and in some circumstances is economically competitive with the conventional blast-furnace--basic-oxygen-process (BOP) route to steel. This raises a number of interesting questions, several of which could be of great interest to the coal and ore mining industries. For example, what are the quality requirements of the raw materials for direct-reduction--electric-furnace steelmaking? Would they be different from the present requirements for blast-furnace--BOP steelmaking? Other questions relate to how much steel will be made by the direct-reduction route in the future. The quality questions can be discussed with a fair degree of certainty, but a prediction of the amount of steel that will be produced by the direct-reduction--electric-furnace route is beyond the scope of this paper. However, an attempt will be made to identify some of the factors that will influence whether there is a swing to direct reduction and the rate at which it may occur.

Jan 1, 1978

By Wen Lan Chen

In the plant where the 800m diameter cyclone was tested, 500 STPH of 50m x 0 raw coal was pulped in a heavy medium tank and pumped originally to four 700mm heavy medium cyclones. For the test one of these units was replaced by an 800mm diameter cyclone with the subsequent feed pressure for both units sets at approximately 15.0 psi. Since this was a feed to zero plant, an appropriate bleed of heavy medium to the dilute medium circuit was established to en- sure that the cleaning of the 500m x 0.5mm raw coal would not be adversely affected by high levels of 0.5mm x 0 fine coal present in the heavy medium. The medium gravity measured varied between 1.41 and 1.43. During a three-hour test on June 10, 1983, the raw coal sample was collected from the feed belt while the clean coal and refuse samples were collected separately at proper locations along the product streams of the two different diameter cyclones. All of these samples were shipped to the laboratory for screen and sink- float analyses. The raw coal screen and ash analyses are shown in Table 1.

Jan 1, 1984

By K. Saberyan

A technique is described for the solvent extraction of zirconium. In this method, zirconium has been extracted quantitatively from 0.005 M sodium salicylate solution at pH 2.5 - 3 using 0.01 M triphenylphosphine oxide dissolved in toluene as an extractant. Zirconium has also been recovered quantitatively from 0.2 M potassium thiocyanate solution, but extractions in nitric and hydrochloric acids (as media) were negligible. The resulting extracted metal ion has been stripped with sulfuric acid (0.5 M) and determined with inductively coupled plasma atomic emission spectrometry. This method has been applied successfully to achieve 95% recovery of zirconium from zircon concentrate.

Jan 1, 2010

By D. L. Kuck

Water ice pillars far underground mine roof support can be frozen and/or maintained and/or melted on demand. The system to do this consists of a refrigeration brine chiller, brine circulation system and disposable plastic containers. Fusion expansion, resilience to dynamic loads, plastic deformation under stress, and non-contamination of coal or ore are unique properties of ice. Lower labor and material costs are economic advantages of ice far mine structural support. Ice brattices can become ice pillars on retreat. For safety, ice pillars can be placed (by remote control, if necessary) in hazardous sites without human entry.

Jan 1, 1988

By Michael Rehbock-Sander, Romed Insam

"INTRODUCTIONThe idea of building a summit tunnel under the Brenner occurred to the Italian engineer Giovanni Qualizza as far back as 1847. But it was to be another 160 years to pass before a base tunnel was to be built.In 1971 the idea of a tunnel at the Brenner was dusted off again. The UIC, the International Union of Railways, commissioned a study for a new Brenner railway with a base tunnel. By 1989 three feasibility studies had been drawn up which formed the basis for further planning of the Brenner Base Tunnel.This was the start of the planning activities. In 1994, the European Union included the Berlin-Naples corridor in the list of priority projects. Ten years later, Austria and Italy signed a State Treaty to build the Brenner Base Tunnel. In that same year, what is today the BBT SE was established.PROJECT DESCRIPTIONThe Brenner Base Tunnel (BBT) with a length of 55 km is the centrepiece of the Helsinki-Valletta Transeuropean Traffic Corridor from Finland to Southern Italy. The BBT tunnel system connects in the north with the Innsbruck station (Austria) as well as to the feeder routes in the Lower Inn Valley, and opens to the south with the projected new line in the direction of Verona (Italy). The tangible design efforts have been underway since 1999; the start of construction of the first section was in the year 2007. The project is financed by the Italian and Austrian governments (each 30 %), as well as by the European Union (40 %).From 2027 onwards the Brenner base tunnel, including the existing lines connected with it, will carry a daily average of 330 trains (approx. 80% cargo trains and 20% passenger trains)."

Jan 1, 2016

By Klaus Rieker

"Since the mid-19th century the River Emscher in the German Ruhr District has been used for disposing of wastewater. In the early 1990s, it was decided to replace the existing open wastewater system with a sewer system and to restore the River Emscher to its natural state. The major Emscher conversion project is divided into a large number of individual schemes, with construction phase 30 being the largest. By applying the pipe jacking method, interlinking tunnels with section lengths in excess of 1,100 m are constructed. USAGE OF THE EMSCHER OVER TIME The 85-km long river Emscher flows right through the Ruhr District. It has its source to the east of Dortmund and flows into the river Rhine near Dinslaken (Figure 1).The Emscher has been used to dispose of wastewater since industrialization began about 200 years ago. Intensive coal mining over the years led to considerable subsidence causing stagnant sewer areas which in turn led to typhus and other deceases. Thus in 1899, the Emschergenossenschaft was founded to create an efficient interceptor system for a catchment area of 865 km² through lining, raising and Emschergenossenschaft decided to free the waterways of the Emscher system from sewage and to improve them in ecological terms by 2020. A budget of 4.5 billion euros was earmarked for this purpose.The construction of sewer conduits began in order to no longer transfer the wastewater into the Emscher. The currently ongoing construction of the “Emscher Interceptor” - the main sewer - represents the heart of the Emscher conversion project. The interceptor will run along the river over a length of 51 km. Three pumping stations are required to confine the sewer’s depth to elevations between 15 and a maximum of 40 m below the surface. Since early 2012, the Emscher has been free from wastewater east of the Dortmund-Deusen clarification plant. There are two further clarification plants situated along the Emscher, which treat the still contaminated river water down-stream. Once the Emscher Interceptor is in operation, they will receive wastewater solely from the tunnel system."

Jan 1, 2016

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron and carbon steel), three types of liquids (diesel fuel, hydraulic fluid and engine oil) and four air ventilation speeds (0, 0.5, 1.5 and 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperatures. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Oct 1, 2022

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes thermal drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of commercial dewatering devices were developed for the Coal Cleaning Simulator running under Aspen Plus? during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for size degradation in the devices and fines loss to effluents, where appropriate, and a calculation for moisture content of the product based on particle size and specific gravity distribution. This paper discusses the algorithm for coarse and fine coal centrifuges and gives comparisons between predicted moisture and solids loss and published moisture and solids loss values for various particle size ranges.

Jan 1, 1996

By Roger Storry, Donald Bruce, Arnaud Hochart

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands and under the main shipping channel in Biscayne Bay (Figure 1).The POMT was a unique project which embodied many technical firsts and involved the first large diameter tunnels constructed through Florida’s challenging sedimentary carbonate strata. At the outset, a comprehensive ground investigation was performed, using both conventional and less conventional investigation techniques, to characterise the highly heterogeneous ground conditions.The findings of the investigation had a major impact on the tunnelling methods, triggering a series of mitigation works to ensure that the tunnels could be excavated safely and effectively. The mitigations included modifications to the already designed Tunnel Boring Machine (TBM), to facilitate an innovative excavation process, and a unique grouting campaign (Storry et. al. 2013a). The project was completed and opened to traffic in August, 2014 and has significantly alleviated traffic congestion in Downtown Miami.GEOLOGICAL CONTEXTThe geological conditions at the project site consist of carbonate sediments which can be divided into distinct geologic units; the Miami Limestone Formation (Layers S3, S4), the Fort Thompson Formation (Layer S5), the Anastasia Formation (Layer S6), the Key Largo Formation (Layer S7) and the Tamiami Formation (Layer S8). Multiple changes in sea level over a relatively short geologic time scale have resulted in a heterogeneous profile consisting of interbedded sedimentary rocks and sediments, which vary widely, both vertically and laterally (Figure 2)."

Jan 1, 2016

By D. D. Harbuck

Previous studies at the U.S. Bureau of Hines have shown that only 70 to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the Bureau developed and researched the hypothesis that minor amounts of germanium and zinc silicate, both present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of silica gel formed increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1991

By I. H. Gundiler

Although cyanidation has been universally applied in the processing of gold and silver ores, the search for less toxic alternatives continues. Difficulties encountered in processing ores containing oxidized copper minerals and the inherently slow kinetics of cyanidation have generated a renewed interest in thiosulfate leaching. This process, as well as the catalytic effects of copper ion, were well recognized and widely applied towards the end of the past century. In this study, the effects of copper, ammonia, and thiosulfate concentrations on gold dissolution were investigated using the rotating disk technique. Extraction of gold and silver from an oxidized copper-bearing ore was also studied utilizing a statistical experimental design, and these results were displayed in the form of contour plots.

Jan 1, 1993

By Frank E. Sullivan

The separation of liquids from granular materials has been widely studied by a number of: investigators over a period of years in an effort to more fully understand the physical phenomenon which occurs. Liquid may be removed from solids, or partially removed, by gravity separation, mechanical separation' or heat drying. Mechanical separation is advantageous when compared to heat drying principally from a cost saving standpoint and also on certain materials which are heat sensitive. It is realized however that mechanical separation of liquids has certain practical limitations. In order to evaluate the efficiency of mechanical separation and predict the extent of, liquid removal, it is first necessary to study the forces which hold the liquid to the solids. From a very practical observation using gravity drainage, it is soon obvious that a pile of coarse solids will drain faster and retain less liquid than a pile of finely divided solids of the same material. For commercial operations it is important to estimate the residual liquid which will remain after a mechanical separation. Batel (1) explored the various quantities of liquid present in the interstices of the bulk granular material. From his work and other authors which he has correlated in one of his recent papers, various formulas are now available which permit an empirical relationship to be developed showing residual moisture versus mechanical separating forces.

Jan 1, 1965

By J. G. Mansanti

The metallurgical response of a deposit's various ore types usually has a strong impact on the flowsheet design of most mineral processing plants. This impacts the materials handling, equipment selection, capital and operating costs, and plant availability. Because of the rapid leaching characteristics of Chimney Creek ores a variation of the conventional gold plant, carbon columns and CIP was proposed. The proposal consisted of a washing stage which was installed between the typical leaching and CIP stages. The circuit was simulated in the lab and was modelled using a computer program to evaluate the metallurgical impact and the effect on the system's mass balances. Also, actual plant data was reviewed comparing the results that were achieved with the results that were expected.

Jan 1, 1988

By C. J. Pritchard, R. D. Jacksha, K. V. Raj, C. B. Sunderman

In underground metal/nonmetal mines, repeated localized short-term exposure to high levels of airborne contaminants can become a serious health issue. Currently, there are no common mechanisms to control or mitigate these short-term high exposures to contaminants. To improve miners’ health and safety, the U.S. National Institute for Occupational Safety and Health’s Spokane Mining Research Division (SMRD) is developing a smart monitoring and control (SMAC) system for the real-time monitoring of mine air quality, with integrated countermeasures to reduce high concentrations of airborne contaminants in localized sections of mines. To develop and test a SMAC system capable of being implemented in an underground mine, SMRD researchers built a test apparatus incorporating a fan, louver, ducting and sensors combined with atmospheric monitoring and control software. This system will institute effective countermeasures to reduce contaminant levels, improving miner safety and health.

Jan 1, 2018

By Howard L. Hartman

Pardon my audacity, but I feel that this is the solution, not just a solution. Further, I will be so bold as to maintain that this is the last-ditch, eleventh-hour chance for the mineral industry to solve its critical technical manpower shortage. I am not being facetious. I am convinced that there is only one solution--just as there is but one real cause of the problem. My conclusion 'is reinforced by countless talks of endless hours with people both in and out of the industry, with employers and employees, and with educators and students. While I claim no originality for the idea and have no pride of authorship, I am concerned that the industry hear and heed in time. It is quite unlikely that the mineral industry and the mineral engineering profession will willingly subscribe to my thesis or gladly buy my proposal. I am convinced, however, that it is the only course of action open to us, and the only course of action which will succeed.

Jan 1, 1967

By R. Flores V.

The Refugio Project is located in the Andes mountains of northern Chile, in the Maricunga Hineral Belt. The Verde, Pancho and Guanaco Au ore bodies have been recognized and are Early Miocene in age. Mineralization consists of fine-grained disseminated gold hosted by dacitic to dioritic subvolcanic porphyries. Alteration comprises massive to veinlet-controlled silicification overprinted on earlier potassic and propylitic alteration and surrounded by later argillic alteration. Geologic relationships suggest that the Refugio ore bodies occur within an Early Tertiary volcano overlying Paleozoic and Mesozoic basement rocks. Geologic reserves at Refugio are approximately 300 million grams (9.7 million ounces) of gold. The Verde deposit contains 185 million tonnes of mineable and leachable ore with an average grade of 0.90 glt Au and is currently in the pre-construction stage after a positive feasibility study. Proven and probable mining reserves at Verde deposit are 101 million tonnes at an average grade of 1.02 glt gold. Additional potential exists at to other deposits within the Refugio property (Pancho and Guanaco) but no reserves have yet been defined due to the limited drilling to date.

Jan 1, 1994

By D. Ofiara, M. Lewis

Tunnel Boring Machines (TBMs) have been used in mining in decades past, but their use has been limited and sporadic. This has changed in recent years, with TBMs being used at Stillwater Mine, Grosvenor Coal Mine Slopes, Sirius Minerals potash mine, and more. These machines are all full face, circular TBMs—a design that has thus far have been unable to tackle a larger issue for mines: typically a flat floor is needed for mining vehicles to traverse. A novel type of non-circular boring machine is now answering the need to quickly reach underground ore bodies while cutting a rectangular profile in hard rock. This cross section allows for use of typical mine trucks and other rubber-tired mine vehicles. The machine uses disc cutters to cut the rock, and has a support structure similar to an open type TBM; however, the cutting geometry is entirely different. The machine is currently cutting an access tunnel at a silver mine. This paper reviews the design and operation of the novel noncircular tunnel boring machine, and describes possible future adaptations to provide safe, sustainable mine development.

Mar 2, 2022

By Quispe Mamani, Mayra Casas Azañero

The research is located within Asuncion and Cospan districts, which according to their geological features in contrast with previous studies pointing out Au, Mo and Pb anomalies create an environment of prospective interest. The objective is to use ASTER Satellite Images to identify ore-bearing hydrothermal alteration zones. To do this, processing techniques such as the combination of bands by RGB 943 and 461, band ratio 4/6, 4/5, 5/8 and 2/1 to identify advanced argillic, argillic to phyllic and propylitic alterations. In addition, indices defined by Ninomiya were used as a third technique in order to reinforce the data obtained from the previous techniques. The results in the study area are confirmed by the SAM spectral mapping technique using spectral signatures from the USGS library. Identifying kaolinite, alunite and pyrophyllite, assemblages of the advanced argillic alteration. Concluding in 3 areas of interest with the band ratios, 5 areas with the Ninomiya indexes and 9 areas validated with SAM, which were contrasted in 13 areas of prospective interest with well-marked argillic alteration.

Feb 1, 2025

By Igor Gonzales G.

Southern Peru Copper Corporation (SPCC) has recently completed the construction of copper leaching, solvent extraction, and electrowinning facilities at their Toquepala and Cuajone plants in Southern Peru. Much of the ore for these new operations is the result of the existing mining operations that have been in existence as early as 1959. At Toquepala, pre-conditioning and bacterial dump leaching of the sulfide ore that was too low in copper content to be processed through the copper concentrator began in 1987. The Cuajone heap leach operation is treating copper oxide ore that has been stockpiled since the Cuajone concentrator began operation in 1976. The pregnant leach solutions from the dump leaching at Toquepala and the permanent pad heap at Cuajone are combined into one plant feed solution. Adjacent to the large dumps at Toquepala, a solvent extraction and electrowinning facility has been constructed. The electrowinning facility has a planned annual production rate of35,000 metric tons per year Grade A cathode copper. Initial production of the cathode copper began in November 1995.

Jan 1, 1996

By Iga Trisnawati, Fitria Puspita, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Idi Amin, Andi Nurfaadhilah Ulfah

Laterite ores, rich in essential metals like nickel, iron and cobalt, are a crucial resource for modern technology. However, the extraction of nickel from laterite ores is a complex process due to their intricate mineral compositions and low nickel concentrations. This paper presents the results of a study to understand the leaching behavior of preroasted laterite ore and the impact of roasting on leaching kinetics. The ore was subjected to roasting at 280 and 610 °C for a duration of three hours, followed by leaching in sulfuric acid (H2SO4) under atmospheric conditions. The results show that preroasting the ore at 610 °C significantly improved the recovery of nickel during leaching, with recovery rate of up to 93 percent, and the leaching process of the preroasted ore was primarily controlled by diffusion through the ash layer. The activation energy values were found to be 20.97 kJ/mol for the ore roasted at 280 °C, and 18.97 kJ/mol for the ore roasted at 610°C. These findings suggest that preroasting can enhance the leaching performance of laterite ore, potentially paving the way for more efficient and sustainable nickel extraction processes.

Aug 1, 2024