Search Documents

By Bryan Ulrich

Knight Piésold and Co. hosted its annual roundtable discussion on March 17, 2011 at the Stockman Hotel and Casino in Elko, NV. The theme for Roundtable 2011 was, ?High density tailings, paste, and filtered tailings,? although the topic may well have been subtitled, ?Don?t prematurely rule out any technologies before they are given their day in court.? Bryan Ulrich, Knight Piésold?s local representative, as well as Tom Kerr from Knight Piésold?s office in Denver, CO, were on hand to help facilitate the discussion. Ulrich and Kerr are senior vice president and president of Knight Piésold?s U.S. practice, respectively. The event played host to more than 30 attendees from several western states. Attendees included personnel from a dozen mining properties and various corporate offices. There were also attendees from manufacturing and specialist consulting firms who have been providing services to various high-density tailings, paste and filtered tailings operations worldwide. It may be noted that the term ?filtered tailings? is used in this discussion. Alternative terms, such as ?dry stack? or ?dewatered tailings,? should be avoided whenever possible, as such terms tend to give a false sense about the nature of the material since these materials typically still retain a significant amount of moisture.

Jan 1, 2011

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By M. Tomono

Harima Works is operating as the zinc and lead simultaneous smelter utilizing the imperial Smelting Process. The smelter commenced its operation in 1966 with designed capacities of 3500 t/M of zinc and 1500 t/M of lead. After that, owing to the results of progressive developments and improvements in operating efficiency and equipments, it has doubled its production figure. This report reviews our recent developments carried out from 1983 to 1985. Firstly, the furnace bottom design was modified for the purpose of reducing carbon consumption ratio. As a result, shaft operating condition has been satisfactory and carbon consumption ratio was improved by 2%, in addition, furnace zinc production was increased by about 8%. Secondly, the oxygen enriched operation at sintering machine was tested from July 1984 to June 1985, in order to increase the sinter productivity, and to solve the capacity imbalance between sinter plant and ISF. As the test result, it was found out that sulfur elimination rate was increased by approx 10% with the oxygen enrichment of 500 Nm3/hr.

Jan 1, 1986

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By Robert L. Marovelli

Organizational development that attempts to simultaneously deal both with training and with job design parameters as they relate to mine health and safety, productivity, and quality of life is one of several areas of research that the Bureau of Mines is pursuing. The Bureau sees potential in this particular effort for reducing accidents and injuries, improving worker satisfaction and health, and increasing productivity.

Jan 1, 1981

By S. Tuylu, D. Adiguzel, U. G. Akkaya, A. Bascetin

"One of the main problems for storing of the tailings is acidity occurrence due to several factors such as existence of sulfuric minerals and also the pollution in seepage waters by mobilization of metal ions, which holds great risks in terms of environmental regulations. Because of these specified reasons, tailing materials to be used in a SPD formula should have comply with some specifications. Among these properties; oxygen content, temperature, matrix suction and pH are the most important parameters. In the study, the relationships between the parameters mentioned are investigated to reveal optimum paste design layout. The lowest amount of seepage water obtained from the paste layers in the pilot cabinet was found as 2150 ml from 3rd layer. As for the maximum seepage water and the average of the all 11 layers were found as 4909 ml from 6th layer and 3273 ml respectively. The reactions occurring according to the oxidation, as seen at seepage water of second and third layers, decreased the pH of system to the under of 7 value. Additionally, when the seepage water of first layer’s EC value is 2.93 mS/cm, the EC value of second layer is increased at 3.54 mS/cm. The other parameters are evaluated with the obtained results of the tests to determine the optimum storing conditions for SPD.INTRODUCTION Conventional waste disposal methods, although widely used, pose great environmental risks. One of the most important issues is acid mine drainage (AMD). Tailings of metallic mines contain heavy metals, aggressive chemicals and hazardous materials. In the presence of oxygen and water, an oxidation reaction can occur, causing a decrease in pH of the environment, and heavy metals that are present in the environment can dissolve easily. Subsequently, heavy metals can pollute underground water basins, creating a great amount of danger for the ecology and potable water resources. Another important risk associated with conventional waste disposal methods is accidents related to the waste dam. Higher volumes of water and tailings (usually 15% solids and 85% water by weight) are sent to waste dams, making it very difficult to control the stability of the dam under conditions such as static and dynamic loads (seismic activities, vibrations caused by blasting, etc.), flooding, and seepage. In case of an accident or failure, the spread of great amounts of mud containing hazardous chemicals and heavy metals can harm the environment of the dam site significantly (Bascetin et al., 2014). In the paste technology, depending on the type of ore, tailings used in the paste mixture can contain sulphide minerals (such as pyrite and pyrrhotite). These minerals are known to be reactive with water and oxygen to produce acidity (sulphuric acid)."

Jan 1, 2015

By Robert Walker

The win theme of this session is Unique Material Handing Systems. The theme was selected because of two major factors. 1. Accomplishments of unique character manage to attract interest regardless of their age. 2. There is much to be learned from pioneering efforts of the past as they are the stepping stones to technological development. Thus, 2-1/2 years after completion, the engineering feat of Oroville Dam still looms large let us take a close look at this project to see what made it unique. To begin with, it established a number of firsts: At 770 feet it was the highest earth fill dam in the world. At $121 million dollars, it was the largest ever United States construction project (Civil). At 80 million cubic yards it had the largest earth volume of any dam in the world. The extensive use of belt conveyors for this application had never before been tried. The use of a high capacity bucket wheel-excavator with shiftable belt conveyors had never before been utilized as a con¬tractor's tool. The principal of the "integral train" was applied most effectively whereby up to 220,000 tons of material-was transported daily some 14 miles. To achieve optimum economics a number of technical breakthroughs were necessary. The suppliers of major commercial components worked hand-in-hand with system engineers to develop new machinery necessary for the highly mobile characteristics of the systems, viz., single pulley drives delivering 2000 horsepower, 1000 horsepower right-angle shaft-mounted reducers, across the line starting of 1000 horsepower squirrel cage motors, 10 miles of steel chord conveyor belts with belt tensions up to 150,000 pounds, aircraft-type disc brakes, hydraulic take-ups, train loading at a rate of 25,000 tons per hour, automatic train indexing for rotary dumping at 10,000 tons per hour, roll-over car dumping without uncoupling cars, shifting 7500 ft. long conveyors up to 300 feet laterally without disassembly. These are some of the superlatives that have made the Oroville Dam project unique. The measure of its success is demonstrated by the results.

Jan 1, 1970

By Kenneth M. Reim

In 1971, United States Borax & Chemical Corporation (U.S.Borax) initiated a mineral exploration program on federal lands in Southeast Alaska, with the commitment that any possible development would be done with great care for the environment. This program resulted in the discovery of a molybdenum deposit and the location of mining claims in 1974, in an area 45 miles east of Ketchikan, now called the Quartz Hill Molybdenum Project (Figure 1). At the time of this mineral discovery, the area was part of the Tongass National Forest, managed by the Forest Service, United States Department of Agriculture, and open to mineral entry and multiple use. In late 1978, the area was designated Misty Fjords National Monument and closed to mineral entry, and in late 1980 the area surrounding Quartz Hill was classified as Wilderness. These new laws and regulations, as well as the special interest environmental groups which oppose resource development, have significantly delayed and increased the costs of developing Quartz Hill.

Jan 1, 1983

By Tom L. Enos

Increased production through the plant was limited due to thickener circuit constraints. To overcome these constraints and maximize plant throughput to match grinding circuit capability, two options were considered: A. Adding 2000 TPD CIL circuit to operate in parallel with the existing CCD circuit. B. Adding a CIL circuit to treat the entire 4600 TPD while retaining some thickeners for tailings thickening. Option B was selected based on simplified plant operations, reduced operating costs, minimal capital requirements, reduced solution losses, and bullion grade improvement.

Jan 1, 1989

By Carrie Smith

In a major milestone for geoscience, the U.S. Geological Survey (USGS) has unveiled the Cooperative National Geologic Map, the most detailed national-scale geologic map of the country to date. The project offers a fresh, layered look at the rocks and sediments that make up the United States. For geologists, engineers and mining professionals, it provides both a technical achievement and a practical tool that will help shape future exploration and landuse decisions across the country. The new map provides a regional view of geology both on and beneath the Earth’s surface. Using different colors to represent rock types and sediments, it allows users to toggle through multiple layers, revealing for the first time the surficial and quaternary deposits that lie above the bedrock. “This is the first national map to include multiple layers of mapped geology, the first built to be easily updated as new maps are published, and the first to be delivered in a user-friendly online interface,” said Joseph Colgan, a USGS research geologist who led the development team. The Cooperative National Geologic Map is a culmination of more than a century of collaborative mapping between the USGS and the nation’s state geological surveys. More than 100 existing maps produced by state geological surveys and the USGS over the past 40 to 50 years were combined and standardized to create the national data set. During its three-year creation, the USGS prepared digital data, built the system to bring the maps together, developed the web interface and underwent a review and approval process. Through this process, decades of fieldwork, analysis and digital cartography were brought together to provide both national and local expertise.

Nov 1, 2025

By Cary Hirner, Dan Lopez, Ross Webb, Stephen O’Connell

"Construction of the largest desalinization plant in the Americas has commenced in northern Chile. It is part of a several billion dollar expansion at a copper mine whose operations nearly stopped due to the challenge of securing a reliable source of water from the Pacific Ocean in a safe and environmentally sound manner. This paper discusses the risk management, design and construction of a quadruple chamber intake and outfall shaft, high capacity pump station, three 7m diameter vertically drilled marine shafts and three subsea tunnels constructed through challenging Andean hard-rock geology. The three 2.5m diameter subsea microtunnels are being mined with vertical curves through variable quality rock 30 meters beneath the ocean and retrieved in the wet from the 7m diameter marine shafts. INTRODUCTION AND BACKGROUND The battle for securing the rights to a constant water supply is a worldwide issue and nowhere is that more evident than the Atacama Desert of Chile, the world’s driest place with areas of the desert that have not seen rainfall in recorded history. The Atacama Desert also happens to be home to some of the world’s largest ore deposits which require huge amounts of water to extract and process. What available water there is comes from three main sources: deep seated wells, glacial water from the Andes Mountains, and desalinated water. Vying for water from wells and glacial streams and lakes are numerous agricultural and domestic facilities in the valleys surrounding the Atacama Desert. Environmental regulations and legal rulings have limited the amount of “natural” source water which can be used for mining purposes. Desalination plants are a known solution for combating water scarcity, albeit a costly one. The total estimated cost of constructing this desalination plant is over $3B USD, which will include a 2500lps capacity and an approximately 118km pipeline from the coast up to the mine located in the Andes. The overall scope of the project includes design, procurement, and construction packages for the 2500lps desalination plant including the seawater reverse osmosis plant, water conveyance to the mine, power transmission, the reservoir and the marine works package which forms the basis of this paper. Key components of the underground construction portion of the Marine Works are:"

Jan 1, 2016

By Hsu-Hui Hsing

In several previous studies from this laboratory (1-4) the autophobicity concept of Zisman and co-workers (5, 6) has been extended to gas phase adsorption processes. Low molecular weight alcohols adsorb on silica or alumina to yield novel isotherms in that monolayer adsorption occurs at low relative pressures indicative of strong bonding, but subsequently multilayer adsorption is quite sparse and diminishes with molecular weight of the alcohol. Such isotherms fit no standard classification scheme, however, in the vacinity of monolayer coverage alcohol isotherms give an excellent fit to the Langmuir or B. E. T. , Type I model (7). Monolayer adsorption is relatively irreversible and it is thus possible to prepare these chemisorbed layers and perform subsequent adsorption studies thereon. All indications are that the adsorptive properties on such films is radically different from that on the underlying alumina (4, 8) and in one study finite contact angles for hydrocarbon fluids were observed. One perennial conceptual difficulty is that there is no observed upper bound to the adsorption isotherm which would be necessary for autophobic adsorption to occur. The cause for this has been studied, and it is currently believed that adsorption is complicated by reversible capillary condensation at contact points between powder particles. The evidence for this is that large particle powders give less "apparent" adsorption at high relative pressures and in one very tedious study adsorption on planar sheets, oxidized aluminum displayed similar reduced uptake at high relative pressures when compared with high specific surface area powders (3).

Jan 1, 1974

By M. A. Reyes, L. Yan

Heat and humidity buildup withn refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a lifesustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ.

By V. C. Koppe, J. F. C. L. Costa, D. M. Marques, A. Amaral

Errors associated with estimating the grade of an attribute of interest in a deposit can compromise planning, sequencing, and mineral beneficiation decisions. Several factors are associated with estimation errors. Among them, we can highlight the factors associated with sample spacing, the size of production volumes, and the variability of the attribute considered in the estimation. The access to estimation error can be obtained by some geostatistical methods, for example, by stochastic simulation. However, this is a process that in some situations is computer intensive and takes time. Previous works have proposed a simplified method to access the Maximum Estimation Error (MEE) associated with different types of grade variables, depending on the sample spacing, at small production volumes and considering specific coefficients of variation ranges. This paper presents an approach to assess the MEE associated with long-term volumes. Considering the methodology proposed, it is possible to approximate if a specific drilling pattern used in a deposit provides an acceptable pre-determined estimation error for Resource Classification. Results and considerations on the impact of the geometry of larger production volumes on the MEE calculation are also presented.

Jun 25, 2023

By J. Miller, B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand, and gravel (SSG) sector in the USA. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine. A validated numerical model was used to explore the potential behavior of the pillars and roof as loading conditions change. The validated model was used to compare changes in mining sequence, overburden depth, and the in situ stress field. This will allow mine operators and engineers to have a better idea of the conditions that could be encountered as mining progresses. Results from the numerical modeling indicate that roof displacement more than doubles as the vertical stress increases from 10 MPa (1450 psi) to 19 MPa (2750 psi) when the maximum and minimum horizontal stresses were 41 MPa (5950 psi) and 22 MPa (3190 psi), respectively. Consequently, as the pillar load increases, the safety factor of the pillars is projected to decrease by about 25%. The impact of the practical application of numerical models can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 2, 2021

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By M. Fan, Z. Long

"This paper presents some studies on recovering valuable elements from Chinese coal by-products, including coal combustion fly ash, stone coal ash, and coal flotation tailings. Both commercialized technologies and economic potential recovery methods are described in this study. Magnetically stabilized air-dense medium fluidized bed separation, tribo-electrostatic separation, froth flotation, and hydrometallurgical methods are discussed in recovering various valuable elements in Chinese coal by-products from different coalfields. These valuable elements include iron, carbon, aluminum, rare earth elements, lithium, gallium, germanium, uranium, titanium, scandium, silicon, vanadium and phosphorus, etc. The ultimate goal is to fully utilize all valuable elements in coal by-product. Each component within coal by-product should be efficiently segregated to its highest value. INTRODUCTION Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium, and phosphorus, etc. These coal-associated elements are significantly enriched in coal combustion by-product fly ash because of majority of main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main elements oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China, and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary widely due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides, and unburned carbon."

Jan 1, 2017

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By J. Weinstein

New erosion, corrosion resistant metal, ceramic, and polymer composite technologies are being developed and marketed by Alanx Products L.P. for use in hydrocyclones, pumps, valves, and other applications in mining and minerals processing. This paper will present an overview of the ceramic/metal composite material system and properties developed, which include excellent erosion/ corrosion resistance. Wear data will be shown from a variety of laboratory tests in dry and wet conditions, in aqueous neutral and corrosive environments. Comparisons will be made with a variety of competitive materials currently used in the industries sited. Data will also be presented on field tests with pumps and hydrocyclones in hard rock mining and other abrasive/corrosive environments. Field data from North and South America, as well as Australian mining applications will be highlighted.

Jan 1, 1992