Search Documents

By John F. Burst

For several generations now, the high alumina clayey sediments of Southeastern Alabama and Southwestern Georgia have supplied those regions with steady, mineral-based income although the impact of that income has been relatively minor until recently. Since World War II, mining activity has increased algebraically with over half of the total ore value in the Alabama area having been recovered since that time. The Georgia area production increases are even more dramatic. The trends are continuing and the next decade should see ore winning figures which will dwarf all previous production. It's time for the mining engineers to take note of this development as the mining methods, similar to the production, have developed rapidly and now offer challenges for the most competent professional. The development of mining techniques has followed a classic pattern. Beginning almost a hundred years or so ago, with the loading of weather-resistant surface boulders into mule-drawn wagons, mining methods have progressed to discovery of limited surface exposures in outcrop and eventually to stripping and development of non-obvious, subsurface deposits. Little by little, the overburden thickness of new pits has increased until, at present, pits with 100' -125' of overburden are being actively worked. Ground water problems in the Eufaula District are particularly challenging. At A. P. Green's J. W. Baker Pit, #l, in Barbour Co., Alabama, it is necessary to continually pump groundwater at the rate of about 400 gallons per minute from wells on the periphery of this large pit in order to keep the water table low enough to allow mining of the ore body.

Jan 1, 1972

By H. L. Lovall

Huge banks of preparation plant refuse and other non¬saleable materials have accumulated over the years in all major United States coal producing areas. These banks, esthetically and commercially undesirable, can cause air and water pollution and land reclamation and mineral conservation problems for the industry and nearby communities Although some refuse banks have been reworked to recover saleable coal, all remain and accumulation continues. Even those previously processed continue as potential hazards. Among the several problems created by refuse banks, in situ combustion is most treacherous. Of the millions of tons of major accumulations, there are at least 450 refuse banks on, fire at this time Attempts to extinguish such fires are costly, impractical and generally unfruitful. Studies are in progress to evaluate the potential of processing such materials to eliminate the combustion capability and to yield usable fuel and nonfuel products. Aspects of the study now in. development for coal refuse include: (a) evaluation of characteristics (size, sink-float, ash, sulfur and calorific value) of the coal refuse materials which are known to be highly variable, (b) development of an ignition test having significance for in situ conditions, (c) study of processing capabilities (comminution for liberation, pilot plant washing tests), and (d) investigation of potentially significant properties of fuel and nonfuel products which could be altered to enhance their market potential.. Among the latter products are lightweight aggregate, fill for mine slushing operations, construction, etc: Plans are to extend the studies to include the design, erection, and test processing of refuse with a transportable plant,; which could provide basic economic and product utilization data from several locations

Jan 1, 1964

By Brianna Eiter, Max Barham, Tim Bauerle

Fatigue-related risk is a persistent safety concern for the mining industry. However, fatigue and sleepiness are often treated interchangeably, which can lead to confusion and potentially less effective reduction of safety risk. To provide clarity, we present an overview of similarities and differences between work-related fatigue risk and sleepiness including definitions, theories, measurements, and mitigation strategies. As a supplement, a summative visual model which highlights these similarities and differences is presented. Expanding industry knowledge in this area will assist safety professionals in crafting more targeted risk management practices appropriate for work-related fatigue risk, sleepiness, or both.

Dec 19, 2023

By B. Eiter, M. Barham, T. Bauerle

Fatigue-related risk is a persistent safety concern for the mining industry. However, fatigue and sleepiness are often treated interchangeably, which can lead to confusion and potentially less effective reduction of safety risk. To provide clarity, we present an overview of similarities and differences between work-related fatigue risk and sleepiness including definitions, theories, measurements, and mitigation strategies. As a supplement, a summative visual model which highlights these similarities and differences is presented. Expanding industry knowledge in this area will assist safety professionals in crafting more targeted risk management practices appropriate for work-related fatigue risk, sleepiness, or both.

Feb 1, 2023

By D. D. Harbuck

The U.S. Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent such as 502 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage counter-current leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with 502 or sulfuric acid.

Jan 1, 1991

By R. Q. Honaker

Recent studies conducted at Virginia Tech have shown that ultrafine coal particles can be selectively coagulated and separated from mineral matter without the use of traditional agglomerants or flocculating agents. This technique utilizes hydrophobic interaction forces to induce coagulation of coal particles, while particles of mineral matter are dispersed using pH control. After selective coagulation, the coal coagula can be recovered by a sedimentation technique. In the present work, factors such as pH, particle size, and solids concentration have been examined. A wide range of coal samples have been successfully upgraded using this technique.

Jan 1, 1991

By Yuting Xue, Lihong Zhou, DAVOOD BAHRAMI

The paper discusses the use of machine learning (ML) to develop a predictive model for determining the location and size of underground mine fires using simulated ventilation data. The study highlights the importance of prompt fire location determination for effective firefighting strategies and reducing injury risks. The ML model was trained with simulated data and achieved an accuracy score of 0.920, which improved to 0.962 by grouping closely connected airways.

Sep 1, 2023

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

By K. V. Raj, M. McNinch, A. L. Miller, J. Wilson, D. A. Parks

Diesel particulate matter (DPM) has been shown to contribute to various adverse health effects on underground miners. In order to reduce worker exposures, it is critical to measure the levels of DPM in the active work settings and in real time. However, the 5040 method, developed by the National Institute for Occupational Safety and Health (NIOSH), which quantifies the mass of elemental carbon (EC) and organic carbon (OC) in the samples, is based on full-shift samples, and can take days or even weeks for results. Use of real-time monitors could significantly reduce the risk of DPM exposure to miners, and available monitors have been shown to quantify DPM, mainly using the EC and other surrogates. The NIOSH Spokane Mining Research Division is conducting research aimed at developing a field-portable DPM monitor that is able to quantify both EC and OC. One part of this work is to understand the effect of OC on currently available real-time DPM monitors. This paper will present the results from experiments that were designed to observe the effect of OC on real time monitors and compare the results with the NIOSH 5040 method. BACKGROUND Diesel engines remain ubiquitous in mining environments and, as such, are one of the primary sources of ultrafine- and nano-aerosols in the mining environment in the form of diesel particulate matter (DPM). As a result of their small size, DPM has longer residence times in a mine atmosphere than the typically larger mechanically generated dust [1]. In addition, the small size enables DPM to penetrate deeply into the respiratory system [1], and exposure to DPM has been shown to contribute to various adverse health outcomes of the pulmonary system [2] and cardiovascular system [3]. Diesel exhaust has been classified as a carcinogen to humans (Group 1) by the International Agency for Research on Cancer [4]. Due to mounting concern about adverse health outcomes, extensive efforts are being made to reduce workers’ exposure to DPM, with the high exposures that often occur in underground mines being of particular concern [5]. New technologies are being developed to reduce engine emissions and thereby airborne DPM levels, including advanced engine technologies, a host of aftertreatment systems [6], and a variety of alternative fuels. The latter have been shown to markedly decrease respirable DPM and other hazardous components of diesel emissions from mining vehicles [7], yet high exposures persist, especially in underground mines [8]. In order to reduce worker exposures, it is critical to measure the levels of DPM in active work settings. In mine settings, exposures to DPM are measured by collecting air samples on filters (usually full-shift samples) and sending them to a lab for analysis using the Mine Safety and Health Administration (MSHA) P13 method, a variant of the National Institute for Occupational Safety and Health (NIOSH) 5040 method. The 5040 method is designed to quantify the mass of elemental carbon (EC) and organic carbon (OC) on the samples [9], which is then used to determine the concentration in the sampled air. MSHA has set a limit for exposure, which is based on the concentration of total carbon (TC), or the sum of both EC and OC. The allowable TC in the air (time-weighted average over the shift) is 160 μg/m3 of TC [10].

Jan 1, 2019

By W. Irwin

As a consequence of the oil crisis of the 70?s, the commercial value of coal increased very sharply and an upward trend in coal prices although now less pronounced, continues today. The graph shown in figure 1 illustrates the trend in the F.O.B. price of U.S. metallurgical coal. This trend occurs during a time when mechanized mining is firmly established as a means of production throughout the coal mining world. With modem methods of mining, mechanical cleaning is a necessity and quality control is no longer entirely dependant upon coal face practice. The efficiency of fine coal recovery is of vital economic importance to present day operations and good practice in this field contributes significantly to improving profitability. Numerous processes are available for the duty and this paper discusses one such system, namely the practice of froth flotation.

Jan 1, 1980

By C Rutter, N Shea, K Kolobe

The Henderson mine, a panel cave mine in Colorado, has undergone multiple ventilation system changes to meet dynamic airflow needs. This paper explains the ventilation designs for different production panels, the challenges faced, and the modifications made to optimize the ventilation systems. The study highlights the importance of a robust ventilation system for safe and productive mining.

Mar 2, 2022

By R. W. Waytulonis

New exhaust control techniques and devices may be necessary to meet future diesel particulate matter emission standards in underground coal mines. This paper reviews conventional work practices and devices used to control diesel exhaust emissions, and new techniques being tested by the Bureau of Mines. Discussions will center on important work practices and on the function and efficiency of exhaust after-treatment devices. An industry/government cooperative research project to develop and test an exhaust after-treatment system for part 36 equipment is also discussed.

Jan 1, 1990

By L. R. Todd

Gold Fields' Mesquite mine, located in southeastern California, heap leaches low grade gold ore at an annual rate of 2.7 Mt (3 million st). Ore is crushed in a two stage open circuit and belt agglomerated prior to loading on the leach pads. Since initial heap construction in October of 1985, a number of operating practices have been modified and several agglomeration techniques have been tested in an effort to improve percolation and reduce leaching time. Findings to date are discussed.

Jan 1, 1987

By W. K. Choi

Using electrochemical techniques it was demonstrated that bioleaching of gold from refractory pyritic ores is a complex phenomenon. Many intermediate electrochemical reactions were found to be involved in the oxidation of pyrite, using cyclic voltammetry and carbon paste-pyrite containing electrode. Furthermore, the oxidation process was controlled by solid-state diffusion as suggested by chronoamperometric and chronopotentiometric measurements. Using the Sand's approach, the activation energy of solid-state diffusion was found to be = 22.4 kJ. After bioleaching, 96% gold was extracted from the leach resi¬due with a thiourea solution in 1 hour. A generalized model for the mechanism of pyrite oxidation has been presented.

Jan 1, 1990

By R. J. Zagrocki

Rekindled public concern about lead toxicity has intensified the awareness of lead-bearing materials in contact with the environment and the human population. Lead's common association with other metals makes the increasingly restrictive lead standards a primary concern for a large number of metal and metal-related industries. In commercial scale demonstration tests with lead-bearing wastes, the HRD Flame Reactor process has a demonstrated ability to separate and recover over 95% of the lead as a recyclable oxide, while rendering the remainder of the material as vitrified, non-leaching, and nonhazardous co-product. Recent Flame Reactor process tests and preliminary cost data for secondary lead soda slag are highlighted.

Jan 1, 1992

By H. Cho

There is an indication that high-pressure roller milling promotes selective liberation due to preferential breakage along the mineral boundaries. A study was undertaken to compare the degree of liberation obtained by high-pressure roller milling with that of conventional ball milling. Coals with different HGI's were ground in a high-pressure roller mill and a ball mill to produce products with similar size distributions. The products were then subjected to float-sink separations to determine the degree of liberation. Also, the relative cleanabilities were compared by separating the ground products by froth flotation. The results from this study are presented in the paper.

Jan 1, 1994

By W. A. Haley

Wheel loaders were first introduced shortly after World War II as small machines designed for handling loose materials in various industrial and processing applications. It was not until the early 1950?s, however, that machine size permitted widespread loading of loose or stockpiled material into on-highway type trucks. An ever increasing number of machines continue to be used for this purpose today. In fact, it is by far the major use for wheel loaders in mining and quarrying. Many of these loaders were working at mines or quarries handling in-process or finished material and some were doing shovel clean-up. It was quite natural then, when the primary pit loading shovel was down, to attempt to maintain some production by replacing it temporarily with the wheel loaders. Most of these attempts were not very successful, however, until the really large wheel loaders, 4- to 6-yd. size were introduced in the early 1960's. Since that time these machines have proven they can be productive and economical primary pit loading tools, a job that was once the exclusive domain of the power shovel. To be competitive with the shovel however, conditions must exist or be made to exist, that will be favorable for the wheel loader.

Jan 1, 1967

By D. W. Park

Artificial intelligence has emerged over the past two decades as an important problem-solving tool including techniques such as expert systems, neural networks, tree classification, fuzzy logic, genetic algorithms, etc. These methods can be employed to solve rock mechanics and ground control problems associated with the highly complex nature of rock masses and ground conditions. A current study at the University of Alabama focuses on development of an artificial intelligence system for real-time interpretation of the data collected from longwall monitoring stations, and development of an early warning system for prediction of undesired conditions and prevention of longwall-mine instability problems. This paper describes a ground control management system using UALSAS (The University of Alabama Longwall Stability Analysis System), which is being developed to facilitate maintenance, on-line analysis, prediction, and includes an early warning system. A detailed framework of computer algorithms and their applications are also discussed. The successful application of these artificial intelligence techniques will contribute to a safer and healthier mining environment.

Jan 1, 1995

By D. C. Martin

Stability analysis and design of open pit slopes is generally based on an assessment of rock cores and rock exposures on surface or in underground workings. Until recently, core for such assessments has been readily available from exploration drilling programs. In recent years, many exploration programs have reduced the amount of coring and rely more heavily on less expensive rotary or percussion drilling programs where drill cut-tings are sampled for geological evaluation and assay. This paper describes a technique whereby costs of the geotechnical investigation are reduced by using rotary percussion drilling information to assess geotechnical properties of the rock mass. A limited number of core holes are required to establish basic relationships between the mechanical properties of core and the characteristics of the percussion chips. These properties are used as a basis to extrapolate the coring information to encompass the entire area of the rock mass for which percussion drilling information is available.

Jan 1, 1990

By P. D. Rao

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. Coals from Usibelli Coal Mine and the Beluga coal field have a heating value of approximately 8,000 Btu/lb and 28% moisture. Hydrothermal treatment (at 275 to 352'C) of lump coal from Usibelli Coal Mine and Beluga coal field enhanced the heating value of the coal, on an equilibrium moisture basis, from 8,000 Btu/lb to nearly 12,000 Btu/lb. The product coal with high heating value and 0.2 % S is an environmentally acceptable premium fuel. The Hardgrove grindability index of the coal is greatly improved, further enhancing its value. Increase in hydrothermal drying temperature promotes vesiculation of resinite. Vitrinite reflectance increased to 0.72 and vitrinite was subjected to widespread visiculation resulting in a coke like structure indicative that the material went through the fluid stage.

Jan 1, 1991