Search Documents

By U. F. Beichmann

INTRODUCTION The City of Oslo together with the neighbor municipalities, Baerum and Asker, are presently building a jointly owned sewage treatment plant located on the west side of the inner Oslofjord. The project is scheduled for completion late 1981. Because the location of the treatment plant is at a distance of about 20 miles (30 km) from the city center, a discharge of more than 13 yds 3/sec (10 m3/sec.) of sewage and storm water will have to be transported over considerable distances. The topography of the area and the geological conditions early indicated that the only realistic transport method had to be through tunnels. As planning proceeded, full face tunnel boring emerged more and more as a favorable alternative to conventional drill and blast medhods. Today the scheme comprises nearly 25 miles (40 km) of tunnels being excavated by full face tunnel borers. In addition a number of access tunnels and cross cuts are to be excavated by conventional methods.

Jan 1, 1979

By Georges Cote, Ehsan Alavi, Eren Kusdogan

The City of Toronto's Coxwell Bypass Tunnel is currently being constructed by North Tunnel Constructors (NTC) ULC, a joint venture of Jay Dee Canada, C&M McNally Tunnel Constructors and Michels Canada. This project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five 20 meter diameter storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. 120 m of Starter tunnel and 70 m of Tail tunnel were excavated with roadheaders to help with the launch of the TBM and as part of the contract base scope work. JayDee Canada in Collaboration with Everest Equipment Co. developed an innovative approach to design and build a stand-alone Ring Machine Erector nicknamed Enterprise to erect precast segmental lining in Starter and Tail tunnels in lieu of Cast-In- Place concrete. This paper describes the design and provides feedback on the innovative procedure used to install the rings.

Jun 23, 2024

By Lloyd B. Underwood

In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colorado. Known briefly as NOW, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Figure 1). The NORAD COC, a U. S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources - radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action1.

Jan 1, 1965

By John H. Bassarear

Large scale equipment can reduce both capital and operating costs for concentrators. Large semiautogenous mills can be effectively utilized in big mills but they must be kept fully loaded to take advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semi- autogenous mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4,476 kW (6,000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 mtpd (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and five variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1985

By K. C. Ko, M. D. Bunnell

The studied coal mi1e is an underground coal mine located in the northern Wasatch Plateau of central Utah (Figure 1) . Since operation began in 1981, in situ stress conditions have been encountered which differ from the assumed conditions utilized during early mine design efforts. Geologic structures also varied somewhat from those projected during initial geologic interpretations of the area. The encountered geologic conditions combined with the unusual stress conditions prompted a combined study of in situ stress and stress-related geologic structures. The study was conducted in two phases, with phase 1 consisting of detailed underground mapping and analysis of stress-related geologic structures to determine stress orientations from which they originated; and phase 2, consisting of over- coring two sites within the mine to determine present in situ stress orientations and magnitudes. GEOLOGIC ANALYSIS Three types of geologic structures have been encountered in the mine that act as indicators of stress orientations of the geologic past. Two of these structures, faulting, and igneous dikes, are directly measurable in the mine. A third type of structure, photolineation, was detected through remote sensing methods and shoe god correlation to roof conditions in certain areas of the mine. Faults Two major orientations of faulting have been encountered in the studied coal mine, including a system of N 80 W striking normal faults and a system of N 55 to 70 W striking oblique-slip faults. Only data collected from the oblique-slip faults were used for this study due to the fact that these faults offset the N 80 W faults wherever the two systems intersect, indicating that the N 55 to 70 W system was created by a more recent stress field. Figure 2 shows locations within the mine where data were collected from seven locations along oblique-slip faults. Data collection consisted of measurement of fault plane strike and dip, fault slickenside trend and plunge, and slip direction. The data are tabulated in Table 1. The fault data were then plotted on stereo nets to determine the stress orientations present at the td of faulting (Figure 3). The determined stress orientations are 32~0 included in Table 1. The stereo net plots show average principal stress orientations of: 1) [ ] plunge 1 degree. These data suggest that the N 55 to 70 W oblique-slip faults were produced by a nearly

Jan 1, 1986

By S. Liu

A general account of nitrogen-generating systems, including the surface fixed, surface-mobile and underground-mobile types is presented. These systems have recently been adopted in coal mines in China to prevent and extinguish fires. The paper stresses nitrogen -injection technology and relevant systems of monitoring and stopping air leakage.

Jan 1, 1998

By Wenkai Wan, Charlie C. Li

Strain burst can occur in underground hard rock excavation when the in-situ stresses are high enough. The prerequisite for rock burst is that the total energy released from the rock mass is higher than the energy needed for rock fracture. The total released energy is contributed by both the burst rock and the surrounding rock. The part of the energy from the burst rock is constant per unit volume of the rock, but the part from the surrounding rock is associated with the burst volume. A greater amount of energy will be released from the surrounding rock in the case of a larger volume of burst rock. The postulation for the energy conversion in strain burst is verified through a FLAC3D model in the paper. It is assumed that the strain burst occurs in a circular tunnel that is located in the hydrostatically loaded rock mass in the model. Six pairs of notches with different depths are created in the opposite walls of the tunnel to simulate the bursts. The energies released from the notch rocks and from the surrounding rock are calculated during the burst. The simulation results show that the percentage of the energy released from the surrounding rock in the total released energy increases with the notch depth. The numerical modelling confirms the postulation that the surrounding rock contributes more energy than the burst rock itself in large-scale strain bursts

Apr 26, 2022

By M. Shriwas, F. Calizaya

"Recirculation is prohibited in many coal mining countries because of the fear that the re-use of return air would allow the build-up of air contaminants at the workings. The incorrect design and location of a booster fan in any ventilation network can create unsafe condition due to recirculation. The current approach to investigating recirculation using simulation software requires manual effort which becomes tedious in a complex and a large network. An algorithm-based C++ program was designed to detect the recirculation in a booster fan ventilation networks. This program needed an input file prepared from output file generated by any ventilation simulator. This program created an output file for recirculation. This program demonstrated the strong capability to detect the recirculation in a sample network and a coal mine ventilation network. The outcomes of this program were documented in this paper. INTRODUCTION The proper design and location of booster fans eliminate the safety hazards associated with high main fan pressure. Conversely, the incorrect design of booster fans in any ventilation network can create unsafe conditions due to uncontrolled recirculation. The proper utilization of a booster fan derives benefits to reduce the main fan pressure, leakage, and consequently ventilation cost especially with high resistance network due to deep and extensive working area in a mine. However installation of booster fan may create uncontrolled recirculation, if it is not sized and located properly with respect to main fan. Recirculation is prohibited in many coal mining countries because of the fear that the reuse of return air would allow the build-up of air contaminants at the workings. Therefore, it is imperative to check the recirculation while designing and operating booster fan for a ventilation network. This paper deals with an algorithm based C++ program to detect the recirculation in a booster fan ventilation networks. This program was implemented to detect the recirculation in a sample network and a coal mine network. STATEMENT OF PROBLEM The currently available ventilation simulation programs do not give much information about recirculation for the generated solution (fan pressures). The current approach to investigating recirculation using simulation software requires manual effort, i.e., traversing from node to node in the output network by the simulator while keeping tracks of all the nodes that form recirculation paths. This is an easy task in a simple ventilation network, but it becomes tedious and sometimes very confusing in a complex and large network. Moreover, the presence of multiple recirculation paths makes the manual effort more complex and difficult, especially in separating multiple loops that are connected together. Thus, there is a need for a more efficient program that will detect and quantify the recirculation efficiently, for the generated fan pressures. A program is developed to detect the recirculation(s) in a network."

Jan 1, 2015

By Yi Luo

Simulation of the multi-entry and multi-crosscut (MEMC) ventilation systems commonly employed in U .S. underground coal mines can be very tedious, due to the large number of crosscuts with stoppings to be represented in the network models. In order to reduce the amount of work needed to build the models, a common practice is to represent a number of crosscuts with one equivalent airway. However, this introduces certain errors into the simulation results. In this paper, algorithms have been proposed to simplify the ventilation networks of common MEMC systems encountered in panel development operations. The algorithms can be used to reduce a MEMC system into one airway with an equivalent resistance and to determine the airflow distributions in the system and the leakages through the stoppings.

Jan 1, 2011

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By Pierre J. Wauters, Eddy J. Jacques

Starting up a fan or modifying its setting point either by rotational speed variations or blade angle changes, obviously results in new ventilation conditions in the network, which is, of course, the object of the operation. However, since transient phenomena may then occur, particularly in complex networks, there may be a need to simulate these situations prior to any action. This is all the more true, if we are dealing with a multiple interactive fan sys- tem. Simulations with a transient model have shown that the flow in certain airways could be temporarily reversed due to the pres- sure variations that reach both its ends with a different time lag. This phenomenon may cause dangerous situations to occur in cases of fire or outburst of methane. It is also true that the air flow could be reversed in secondary and less powerful fans, while still rotating in the normal direction. The study and the experimental investigation of the extension of the reverse flow characteristic is therefore justified from two points of view : • a numerical simulation model for transient flow conditions must be capable of handling temporary reversed flows, and thus have appropriate fan characteristic curves available over the entire operating domain; • while operating fans, reversed flows should be avoided or at least reduced. Therefore, the design of start-up procedures or real time control algorithms should take these phenomena into account. A particular interesting application is the operating of two fans in parallel. In order to investigate experimentally the characteristic curves of a fan under reversed flow conditions a small scale model was built. This facility was designed in such a manner that it was possible to carry out experiments concerning flow reversions and to try out sequential start-up procedures for two fans in parallel.

Jan 1, 1997

By Dennis K. Mortensen

Improvements in flotation technology are continually being made in the attempt to achieve the mineral processor's goal of maximum mineral concentrate grade and recovery at zero cost. Technology that cannot be totally proven in the laboratory must be tested under plant conditions either in a pilot plant or in the existing circuit. Problems associated with new technology can be solved effectively by the mineral processor who approaches each of the problems objectively.

Jan 1, 1989

By R. D. Schmidt

An in situ leaching geochemical simulator consisting of flow, mass transport, and graphics support programs has been developed. Two dimensional flow in heterogeneous porous media is modeled using a semi-analytic boundary integral technique. This method involves mapping streamlines to straight line segments in the complex potential plane. Leachant concentration and mineral values are modeled in this plane using the (one dimensional) potential coordinates. A fully implicit finite difference scheme is used to solve the resulting coupled system of four concentration equations. Graphical representations of streamline patterns, concentration histories, profiles and recovery curves are generated. An application of the model to uranium leaching in a heterogeneous aquifer and ore zone setting is presented.

Jan 1, 1985

By Velu Annamalai

In-situ uranium solution mining involves the injection of a lixiviant (leach solution) through appropriately placed wells into the underground ore zone. Upon contacting the uranium minerals, this solution will dissolve the uranium. The uranium containing solution is then pumped out of the wells into a processing plant where the uranium values are removed, typically in ion exchange columns, and the stripped liquor is recycled back into the field. The lixiviants may be acidic or basic. Where the ore zone mineralization contains appreciable carbonate, as in the South Texas fields, acid consumption would be excessive and the typical solution is ammonium carbonate bicarbonate at about 5-10 g/l and a pH of 7-9. Because the usual uranium minerals, uraninite or coffinite, contain uranium in the insoluble tetravalent state, it is necessary to add an oxidant to increase the valence to the hexavalent state where the uranium is soluble. Oxygen dissolved in the lixiviant has been shown to be quite effective for this purpose. It is also much more economical than other oxidants. Of concern is the possibility that (1) its solubility may or may not provide concentration levels adequate to give an economically attractive uranium level in the extracted liquor, and (2) the addition of oxygen in excess of the saturation level so as to increase the uranium grade in the lixiviant may cause gas blockage of the typical fine-pored ore formations.

Jan 1, 1981

By A. K. Bakshi

Slurry rheology affects autogenous grinding performance by changing the rock's breakage characteristics. In this study pilot scale batch autogenous grinding was carried out to observe the effect of viscosity on the breakage characteristics of the rocks (the media), and on the overall specific energy consumption. Clay/fines content, and temperature of the initial charge, were varied to alter the viscosity of the slurry. Results showed that at higher slurry viscosity, rocks became more difficult to break, resulting in an overall increase in the specific energy consumption of the mill. Also, it was observed that viscosity had a significant effect on the amount of critical size material present in the grinding circuit, where the critical size material is the material which is too large to be effectively ground in the mill, and too fine to act as grinding media.

Jan 1, 1996

By R. E. Weeks, D. J. Millenacker

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time- frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The US Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1987

By Robert J. Willard

In its search for additional ways to increase understanding of rock behavior, the Twin Cities Mining Research Center has turned to the scanning electron microscope, an instrument rapidly finding application in research concerned with surfaces of materials. Since features indicative of the manner in which rocks fail may be recorded on the surfaces of fragments as disintegration proceeds, this microscope might be used as a tool for seeking and mapping these minute features. In pursuit of such features, we chose to scan a portion of the fracture surface from a quartzite disk compressively loaded to failure between two pins centered along the disk's axis. The resultant fracture appeared as a rough, diametric plane, and the fracture surface near one of the loading points was scanned with the microscope.

Jan 1, 1969

By James E. Monsees, Wayne A. Carbiener, Michael R. Wigley

This paper illustrates an approach to quantitatively document the degree of technical conservatism to be incorporated into the design of a waste isolation system in bedded salt. It is anticipated that for an actual repository site the key performance constraints and/or design bases identified in this paper will be reviewed, and modified or supplemented as required. Ultimate acceptance of a repository will be dependent upon scientific peer input and scrutiny of the demonstrated conservatism inherent in each specific repository site and design.

Jan 1, 1981

By D. Rajkovic

Geothermal sources are exploited in two basic forms, i.e., the primary form of thermal energy and that converted into electrical energy by using an adequate thermodynamic cycle. There is a possibility of applying several processes for the conversion of thermal into mechanical or electrical energy, which depend on the thermodynamic characteristics of the geothermal water. Geothermal sources in Croatia do not contain steam of relatively high temperature, like in Italy, although both countries are nearly in the same position with respect to geothermal belt. Geothermal sources in Croatia are mostly so-called low-temperature geothermal sources with water temperatures lower than 100°C (Cubric and Jelic, 1993). A few of them have been exploited, although the percentage of utilization of their available power is still very small. The low-temperature potential is a major disadvantage when it comes to power generation, since state-of-the-art geothermal power plants require reheated steam or hot water to operate. There is a common belief that the optimum way of exploiting low-temperature geothermal sources is heat generation. Therefore, this analysis is especially aimed at potential users and showing the technical and economical possibilities of using low-temperature sources for conversion of thermal energy into mechanical work and electrical energy.

Jan 1, 2003

By A. Sfougaris

A study on fauna distribution and abundance is being conducted in the Giona Mountain, in central Greece, area of bauxite mining. The specific aims of the study are: a) to estimate and map the distribution of mammals, and especially of the Balkan chamois, b) to estimate and map the distribution and abundance of breeding birds, c) to count the bird species using the area during spring and autumn migration and winter, d) to update the list of mammal and bird species of the mountain, with emphasis on rare and endangered ones, according to 79/409, 92/43 EU Directives and other relevant conventions, e) to compare the bauxite mining areas and species distribution and assess the possible overlap and compatibility of mining activities - species conservation, f) to assess the possible habitat loss due to planned mining activities. All estimations of mammal species distribution and abundance are being carried out by fieldwork using spotlight during the night along selected routes. Especially for chamois, line transects and vantage points with the aid of telescopes and binoculars are being used. Birds are being counted with the point count method in randomly selected plots distributed in all available habitat types and altitudes. The species distribution and mining areas will appear on thematic maps with the aid of a geographical information system (GIS). Finally, solutions for environmentally compatible mining activity in the area will be proposed.

Jan 1, 2007