Search Documents

By H. Nematollahi

Numerous magnesite deposits are found in the south part of Khorasan state, east of Iran. During the past few years, production of high-grade magnesite ore was possible only by using selective mining method. The decreases of high-grade ore imply upgrading of the low-grade ore. To do so, the objective for the first phase is to obtain a material which contains less than 2.5% SiO2. The present study was carried out based on three different samples. The results obtained in laboratory indicate that the direct flotation of magnesite by fatty acids led to acceptable result.

Jan 1, 2003

By J. L. Post, L. Borer

Small seams of fibrous tremolite and actinolite commonly occur in many California counties. A number of larger seams of this fibrous material were mined from 1882 until about 1955. The fibers from these mines were used for making acid filters, battery cases and fire-resistant paint. With increasing population, new residential areas are being developed in the foothill regions, leading to increased contact with seams of fibrous amphiboles. These forms of asbestos can be particularly dangerous to human health. Thus, it is necessary to determine the locations of these mines and adjacent veins and to identify the specific amphibole minerals present.

Jan 1, 2003

By P. Mousset-Jones, F. Calizaya

Ultrasonic anemometry is a relatively new method of measuring the air velocity in underground excavations and is not widely used. The method has been mainly used for surface applications, such as meteorology and fluid flow measurement. Several instruments were looked at to determine their applicability for continuous underground monitoring systems. The units fall into two main categories: variable distance units and fined distance units. The method relies on the acceleration and deceleration of ultrasonic pulses transmitted through a moving airstream. This study presents some of the results of the testing of variable and fixed distance ultrasonic anemometers in a wind tunnel and a mine drift.

Jan 1, 1995

By Thomas H. Koenning

The number of spontaneous combustion incidents in the U.S. is expected to increase as the consumption of lower rank coals and the use of longwall mining becomes more prevalent. A spontaneous combustion incident holds the potential for substantial loss of life from a mine fire or explosion if not prevented or controlled at an early stage. Laboratory tests have been developed which are useful in ranking the susceptibility of various coals to spontaneous combustion. Ventilation circuits and mining methods can be designed to minimize the risk of spontaneous combustion. Early detection of spontaneous combustion is possible with the combined use of continuous monitoring, periodic gas sampling, and inspection.

Jan 1, 1989

Mines in the Lake Macquarie region of New South Wales, Australia, are faced with the dilemma of having to introduce longwall mining techniques at a time when increasingly large areas of the surface are being used for urban development. Increasing pressures on safety, costs and productivity performance dictate that longwall mining is the method for the future. Construction of surface structures is controlled by a statutory body known as the Mine Subsidence Board (MSB). All surface structures have to be designed to MSB criteria. All mining plans involving secondary excavation also have to be submitted to the MSB for approval. The Board acts as risk assessor in evaluating acceptable levels of surface subsidence vs. the value of the coal resource. Surface repairs are paid for by a levy on all coal producers.

Jan 1, 1995

By Gerald V. Jergensen, Edward J. Samuel

Slurry system are the principal method for storage and transportation of solids within and between concentration operations In a mineral processing plant. A slurry 1s a mixture of solid particles In water, or a chemical solution, that behaves like a liquid. The design of slurry transportation systems is generally analagous to pumping and piping water, but with a few notable exceptions: • The interaction of particle on particle affects slurry transport. • Particles often interact with the fluid, particularly when chemicals have been added to the system. • Particles have a frustrating tendency to settle from the slurry suspension, especially into locations not considered In the design. • Solids have an affinity for wetted surf aces and tend to wear them away. Slurry transportation systems Include a number of separate components, each requiring special design considerations. A systematic evaluation of each component of a slurry transfer system will help overlooking the small details that could cause operational headaches. Most slurry transport systems include: • A receiving sump or tank that provides for mixing and/or momentary storage of slurry. • A driving force.. by a pump, atmospheric pressure or gravity. • A suitable conduit for transportation.. pipes or launders. • A delivery objective.. another sump or process vessel, or distribution system to several process points. • A control strategy and design to regulate the transfer operation. The design of the slurry transportation system normally evolves through the following steps: • Finalizing the process flowsheet and establishing the weights and volumes to be handled. • Identifying and characterizing the various process fluids and slurries. • Defining critical and minimum transport velocities of fluids. • Selecting a pipe diameter (or dimensions and gradient) and

Jan 1, 1986

By C. L. Schaidle

Computers and communications technology have revolutionized many industries. In earthmoving, this revolution has just begun. The major changes are still to come but are just around the corner. This article presents a vision of this upcoming revolution in the earthmoving industry. This vision includes basic communication, machine monitoring and diagnostics, job and business management, planning and operations, and machine control. For the industry to realize maximum benefits from the information age, it must have a vision of the future that is shared by technologists, machinery producers and miners. History of the information age During the 1970s, the information age revolutionized retailing, starting with the grocery business. By using bar codes and laser scanners, individual items were connected to the information world of computers and communications. Once this connection was made, the data on what an item was and where and when it moved became valuable information for inventory control and marketing. Not only was the information valuable, it was easy and inexpensive to collect and manipulate. The effort required to provide the consumer with the right product at the right time was reduced. Costs went down and customer satisfaction went up. But there were casualties of this revolution. Many inventory counters lost their jobs. There were also equipment casualties. Cash registers that could not interface with the digital world were discarded long before the end of their useful life.

Jan 1, 1994

By Tom Bruington

This paper discusses the accuracy of determining the quantities of gold and silver on activated carbon in various stages of process for typical precious metals flowsheets. Accurate plant performance evaluation depends upon reliable estimates of carbon and precious metals inventories. The sources of sampling error are identified and methods of reducing them discussed. Several case studies illustrating the sensitivity of flowsheet performance to sampling error are presented.

Jan 1, 1991

By Subash Chander, B. Arnold

Many developments have occurred in coal flotation with regard to increasing recovery from the flotation circuit and its impact on overall coal preparation plant recovery. This includes innovative design of flotation circuits, equipment modification and development, methods of enhancing the use of reagents, effect of slimes, and recognizing the effect of water chemistry. This paper will review recent advances and present some guidelines to improve process efficiency.

Jan 1, 2005

By L. P. Johnson

Longwall mining has gained acceptance as a safe method of maintaining coal production where conventional systems were unsuccessful or uneconomic due to bad roof conditions (Kuti8). One of the major problems confronting American operators involves the correct choice of equipment which should be selected to suit the local mining and geologic conditions for optimum productivity. To achieve this, factors such as rock strengths, local geology, panel geometry, and panel orientation must be examined to optimize production and minimize down time due to ground control problems. Little quantitative information is available in the literature regarding the effects of geologic conditions on American longwall operations, and past implementations of longwall systems appear to have been based largely on experience. When mining engineers are able to assess the geologic conditions both quantitatively and qualitatively, they can more fully optimize equipment selection and panel design.

Jan 1, 1977

By J. J. Lewis

The chapter describes how several OR techniques assisted the planning of a major new UR project. A computer system was developed to analyze reserves distribution and potential of possible underground layouts, to assist in choosing the location and size of access points. Manpower requirements of each proposed working plan were assessed and matched with the potential recruitment of skilled and unskilled labor. Computer simulations were used to determine the optimum capacity for coal preparation plant and surface bunkerage. For the overall assessment of robustness, financial modelling and risk analysis techniques were adapted to the special requirements of new mines.

Jan 1, 1979

By K. Professor Heiskanen

The improvement of grinding circuit efficiency is a constant industrial requirement. It has often been connected to the improvement of classification. The paper discusses some operational aspects of hydrocyclone classification. A hydrocyclone should be operated close to roping but should not with high density slurries go to roping. Unfortunately roping is not well understood and roping models for controlling hydrocyclone operation are not adequate. The paper discusses also some ways of improving the classification in terms of bypass and imperfection. The last part of the paper discusses the effect of bypass and imperfection on circuit performance.

Jan 1, 1997

By Roe-Hoan Yoon

Froth flotation is widely used for separating particulate materials from one another in aqueous media. The basis of this important separation process is to control the hydrophobicity of particles. However, it is difficult to predict the kinetics of flotation based on contact angle (?), which is a thermodynamic property. A solution to this difficulty would be to develop a relationship between ? and the gradient of the hydrophobic forces across the solid-liquid and bubble-liquid interfaces. Such information can be obtained using the surface force apparatus (SFA), the atomic force microscope (AFM), and the thin film balance (TFB). The present communication reviews the results of the measurements conducted using these methods, and offers a methodology for deriving a rate equation for bubble-particle interactions

Jan 1, 1999

By Conrad Parrish

As originally conceived, this paper was to address the costs of environmental compliance, focus on environmental impact statements, and describe how those costs impact mining projects. The intent was to do wide ranging mathematical analyses to demonstrate the varying impacts on mining projects depending on their size, timing, return on investment and other salient project features. The initial portion of the numerical analysis necessary to this purpose was performed. The results showed a pattern of impacts familiar to the mining industry:

Jan 1, 1991

By Mark Springett

Microcomputers have rapidly evolved to the level at which they can perform almost all of the computational tasks required for exploration, evaluation and exploitation of mineral deposits. The present capabilities of microcomputers are reviewed by examining their use on typical projects from the initial capture of exploration data to the subsequent technical and financial evaluation by microcomputer. Emphasis is placed on the need for compatible software and on the importance of a consistent hardware acquisition policy.

Jan 1, 1987

By B. J. Arnold, F. F. Aplan, S. Chander

There is a broad range of chemical reagents of potential use to the coal preparation industry: flotation frothers, flotation collectors (for coal, ash minerals or pyrite) and collector-assisting (conditioning) agents, flotation depressants (for coal, ash minerals or pyrite), pH regulating agents, acid mine drainage treatment chemicals, flocculants, filtration aids, dispersants, dust suppressants (wetting agents and car-top or pile binders), freeze conditioning agents, water treatment chemicals (corrosion and scale inhibitors) and suspension stabilizing reagents (dispersants, stabilizers, biocides). The application of each of these types is discussed with particular attention paid to those of greatest importance: flotation frothers and collectors, pH regulators and acid mine drainage treatment chemicals, flocculants and freeze conditioning agents.

Jan 1, 1986

By E. Yuksel

Noted as one of the 20 major economies of the world, Turkey is a semi-arid plateau between the Eurasian and the African continents. With its surface area of 780 thousand sq km, it supports a population of 70 million people. While the mining history of Turkey can be traced back as far as 7 000 B.C., mining currently generates only 2% of Turkey’s gross national product. Turkey has 77 of the 90 principal minerals that are mined world-wide. Currently, some 5 000 mine occurrences including copper, lead, zinc, iron, gold-silver, chromite, sepiolite, mercury, and coal deposits, soda ash, marble, zeolite, feldspar, magnesite deposits, as well as the world’s largest known borate deposits, have been discovered and partially explored.

Jan 1, 2004

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982

By R. J. Wesely

It is obvious from recent events in The Peoples Republic of China that a major effort is underway to increase trade with the Western World. The production of Gold contributes to China's ability to participate in international trade and consequently they place a high priority on increasing gold production. Many of the operating gold mines in China contain refractory ores which to date have not been efficiently treated. Figure 1 illustrates the description and location of some of the major gold mines in China. Recognizing that the technology necessary for the economic treatment of this ore has been developed in the United States and other Western Countries, China has begun to seek assistance in evaluating several potential projects. This paper will examine the recent history and current trends in developing a refractory gold treatment project in China.

Jan 1, 1993

By Ralph E. Weeks

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1988