Search Documents

By Chris A. Fleming, Daan Seymore

The Golden Jubilee Mine in South Africa is the first mine in the Western World to introduce resin-in­pulp technology for the recovery of gold from a cyanide-leached slurry. Located in the Eastern Transvaal region of the country, the plant processes approximately 375 metric tons• of ore per day, of which over 90 per cent is mined in an open pit adjacent to the metaflurgical plant, while the remaining 5 to 10 per cent is trucl<ed in from two small high-grade deposits, located about 10 kilometers from the plant. The gold grade in the open pit is about 1 git, while the values m the two high-grade deposits range between 5 and 15 git. At the current treatment rate, the proven reserves m the three locations will last about another 10 years. Early testwork indicated that the ore was not well suited to conventional filtration processing or to heap leaching because of its high cfay content, and that carbon-m-pulp (CIP) would probably prove to be the most viable metallurgical route. Tcstwork to establish the feasibility of CIP for this application was carried out at Mintek in 1985. This worl<, which was based on batch-leaching and carbon-loading tests, indicated that CIP was technically feasible, but that both the rate of gold loading and the gold-loading capacity of the carbon were inferior to those obtained with Witwatersrand ores. The poor adsorption characteristics of the carbon were attributed to the abnormally high concentration of natural organic compounds (humates and fulvates) in the ore. Batch tests were therefore also carried out with strong-base resins, since resins are known (1] to be far less susceptible to organic fouling than is activated carbon. The results were very promising, and pointed to fast kinetics and a high loading capacity. (Fig. 1 ). Notwithstanding these findings, it was decided to recover gold with activated carbon at Golden Jubilee Mine because the CIP process was, by then, well established in South Africa and elsewhere in the world, whereas resin-in-pulp (RIP) was unproven technology. The r>lant was commissioned in September 1986 and, for 18 months, operated in a carbon-in-leach (CIL) configuration, i.e. with a total of . six leach tanks, the last four of which contained activated carbon. As could have been predicted from the laboratory results, the performance of the CIL plant was generally poor, low gold loadings on the carbon (less than 1500 git) and high losses of soluble gold (0.2 to 0.3 p.p.m.) bemg characteristic of the operation. Consequently, it

Jan 1, 1990

By Maribeth Amyot

This paper assesses the current status of computing education in ABET-accredited mining engineering programs in the United States. The hardware and software being used are reviewed. The extent to which computer applications are incorporated into mining engineering courses is also surveyed. Today&apos;s capabilities and practices are compared with those of the past to establish, trends in computing education. The concerns of mining educators regarding computers are addressed, as are views on the direction in which mining engineering programs appear to be heading in preparing students to meet the computing needs of industry.

Jan 1, 1985

By Huang Kong Xuan, Li Yun Teng

Reviewing the development of resin-in-pulp (RIP) technology for the extraction of gold in the world, especially in South Africa and USSR, and the chemistry of interaction between aurocyanide ions and anion-exchange resins. RIP benchtest and pilot plant investigations show that the resin of the weak-base and strong-base can absorb gold in the cyanide pulp and gold can be eluted from the strong-base resin by electro-elution. The possibility of future application of RIP technology in China fa also briefly discussed.

Jan 1, 1998

By A. J. Monhemius, R. G. Reddy, G. W. Warren, E. Peters

Thermodynamic solubility of chromium in pickling solutions (i.e., HF- HN03-H2O solutions) was determined as a function of HF and HNO3 acid concentrations at 298K. Pure Cr, AISI type 316 and 416 stainless steel were used in this study. The results showed that the solubility of Cr increased with increase in the concentrations of HF and HNO3 acids in solutions. The solubility of Cr increased in the order of pure Cr > 416 SS > 316 SS. The theoretically calculated Cr solubility data were in reasonable agreement with the experimental data.

Jan 1, 1993

By E. A. Sigworth

Our interest in metallurgical applications for activated carbon was thoroughly aroused when laboratory studies indicated that each dollars worth of carbon could retain as much as four dollars worth of tin. Since then other data was developed suggesting many Potential uses in the metallurgical field it is hoped that, the information presented in this paper may encourage studies by knowledgeable individuals in metallurgical operations. Activated Carbon accomplishes its results by adsorption which involves selective removal of materials from solution by holding the compounds on the carbon surface at the active areas. An example of adsorption is the dyeing of cloth where the dye is selectively held on the cloth surface and the concentration in the dye solution is thereby reduced. Many theories exist on, adsorption, but the predominant factors involved in metallic ion adsorption probably are that adsorption is indirectly proportional to solubility and is benefited by high concentrations acting to squeeze out molecules in smaller amounts.

Jan 1, 1962

By Gregory B. Baecher, Walter Steiner, Herbert H. Einstein

1. INTRODUCTION Empirical methods have always been important in tunneling in contrast to many other branches of engineering. Beginning in the late 19th century, when engineering entered the phase of formal modeling, this dichotomy could be seen to emerge even in the work of individuals. Culmann (1), Ritter (2) Kommerell (3) and others simultaneously were developing analytical approaches to bridge and building design and empirical approaches to tunnel design. The dichotomy remains. Empirical or simple analytical methods are used at most in the preliminary design of bridges and buildings, while they are used in all phases of tunnel design and construction. In fact, the past decade has seen a resurgence of interest in empirical methods, and with it discussion and controversy. This discussion has centered on the suitability of various methods. In some applications identical results are obtained with differing methods and in some cases radically different ones. On certain occasions the discussion has focused more on the methodological rather than empirical by taking issue with the appropriateness of particular parameters or the structure of some methods. This paper attempts to establish a basis for judging the suitability of empirical methods in tunnel design, and their applicability to particular cases. The paper makes no claim of exhaustiveness, and instead emphasizes basic requirements for application. Various methods are reviewed against this background. A detailed comparison of empirical methods and a description of their concept and background is now being prepared (4). Specifically the paper first defines empirical methods, and their purpose (Section 2), describes their structure (Section 3), and focuses on the basic requirements each must satisfy (Section 4). Then

Jan 1, 1979

By Robert A. Jankowski, George E. Niewiadomski

INTRODUCTION The utilization of longwall mining technology in the United States has steadily increased since the first longwall plow system was installed in 1952. At the errs of FY 1992, some 76 coal mines were employing longwall mining systems for coal extraction, and approximately 78 shearer and 3 plow faces are operating nationwide at any given time. Although the number of operating longwalls has remained relatively constant over the last five years, longwall production levels have increased significantly during this period. During the same timeframe, the number of continuous miner sections has decreased by 13 pct., from approximately 1438 in FY 1988 to less than 1250 in FY 1992. According to Mine Safety and Health Administration (MSHA) data, the average production of longwall sections increased from approximately 2400 tons per shift (tps) in FY 1988 to more than 3100 tps FY 1992. In fact, the average production has more than tripled since 1978, when it was only 850 tps. Approximately 25 pct. of operating longwalls are capable of producing in excess of 4000 tps. Longwall production currently accounts for nearly 36 percent of U.S. underground coal production, compared to 4 pct. in 1978. These improvements are attributed to improved longwall equipment and increased availability, larger longwall panels and automation. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust compliance problems more frequently than other mining system. Although dust levels have remained relatively unchanged over the past five years, averaging 1.6 mg/m3 and 1.9 mg/m3 based on results of operator and inspector sampling, respectively, during FY 1992, approximately 25 pct. of the operating longwalls were in noncompliance during any given bimonthly sampling cycle. Although modest gains in longwall dust control technology have been made, these have been overshadowed by significant increases in production rates. As more coal is mined, more dust is generated (Figure 1). Therefore, the increase in longwall productivity has meant that far more dust is being produced which must be controlled. [ ] In view of the current compliance record, any efforts to further increase longwall output, as has been forecasted, must be accompanied by: (1) the reduction of dust levels at existing operations through the proper installation and maintenance of suitable engineering dust controls; and (2) the advancement of dust control technology for today&apos;s and future longwalls that will enable all face personnel o work in an environment that is free of excessive levels of respirable coal mine dust. MSHA&apos;S RESPIRABLE DUST CONTROL PROGRAM Since 1972, federal regulations have required each coal mine operator to continuously maintain the average concentration of respirable dust in the mine atmosphere during each shift in the active workings at or below 2.0 mg/m3 through the application of environmental dust control methods. The regulations provide for further reduction in the dust standard whenever the

Jan 1, 1993

By Steven J. Schatzel

A study was made of frictional ignitions in the underground coal mining industry from 1980 to 1992. The population of frictional ignitions was correlated to a variety of potential contributing factors including the mined coalbed, geographic location, mine production, methane gas emissions, and the type of mining equipment in use. The number of frictional ignitions reported in 1991 and 1992 surpassed the annual totals in all previous years included in the study. Most frictional ignitions occur during cutting operations at a coal face by a continuous miner. The average coal production of mines experiencing frictional ignitions is greater than the average of all underground coal mines throughout the survey period. Methane drainage may have produced a drop in the ratio of gas emissions to coal production (E/P) in mines experiencing frictional ignitions.

Jan 1, 1995

By V. K. Srivastava, T. Gupta, T. Ghosh

"In recent years, the demand for rare earth elements (REEs) has grown due to increasing demand and global supply shortage. The supply deficit of these critical elements has encouraged the search for new sources, with coal and coal byproducts as possibilities. Coals from certain parts of the world can be rich in REEs and can approach a total concentration of 1,000 ppm. Two Alaskan coal samples, from Healy and Wishbone Hill, were investigated for the effects of density and particle size on REE concentrations for three selected size fractions, and flotation tests were conducted on finer fractions. Additionally, bottom ash and fly ash samples from a power plant were examined for their REE concentrations. The results show that the upgrade potential for REEs on an ash basis from a whole-coal basis ranges from 2:1 for the Wishbone Hill samples to 4:1 for the Healy coal samples. Flotations of the finer fractions of the two coal samples, conducted under similar conditions, revealed higher concentrations of REEs in the tailings. Both coal samples had comparatively higher contents of light-group rare earth elements (LREEs) than heavy-group rare earth elements (HREEs). REE content trends for the power-plant products on an ash basis indicate that fly ash has slightly higher concentrations of both LREEs and HREEs than bottom ash. IntroductionRare earth elements (REEs), also known as rare earth metals, and their compounds are vital components in industrial, automotive, petrochemical, defense and medical applications. Dysprosium in combination with other elements is used in laser materials and nuclear control applications. Neodymium is present in magnets that are used in the manufacture of wind turbines and hybrid cars. Europium, terbium and yttrium are used in devices that have visual displays such as computer screens and laptops (Haxel, Hedrick and Greta, 2002; Bunzli, 2013). REEs pose fewer environmental problems of disposal and recycling than their conventional heavy metal counterparts (Haxel, Hedrick and Greta, 2002). They are key materials for radar systems, avionics, modern national defense and satellites (Cammarata and Sieradzki, 1994; Hedrick, 2010; Martin, 2010; Szumigala and Werdon, 2011; Cordier, 2011; Bunzli, 2013). REEs are often classified into light-group rare earth elements (LREEs) and heavy-group rare earth elements (HREEs). This classification is primarily based on the electronic configuration in the outermost shell. LREEs, ranging from lanthanum to gadolinium, have a single or no spinning electron in the outermost 4f shell while HREEs, ranging from terbium to lutetium, have paired electrons in the 4f shell. This difference in electronic configuration is responsible for the differences in physical and chemical properties of REEs."

Jan 1, 2017

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant, able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). CN- + H202 => OCN- + H2O The most recent development, however, is the use of H202 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O2, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). 2 Au + 4CN- + 1 /2 O2 + H2O => 2 [Au(CN)2]- + 2 OH Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: • In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. • In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: • Hydrogen peroxide must be diluted before it is added to the pulp. • The dosage of H2O2, must be properly regulated based on the oxygen level of the pulp. • An important part of the continuous 02-control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1989

By R. K. Singhal

A sizable surface mining industry exists in Western Canada. There are the surface coal mines in the provinces of Alberta, British Columbia, and Saskatchewan producing the bulk of Canadian Coal. The two oil sands plants in Fort McMurray, Alberta producing synthetic crude oil are surface mining operations. Much of the metalliferous mining in British Columbia is carried out by open pit methods. This paper discusses the current surface mining methods in both of these industries with particular reference to Alberta. Issues relating to environmental impact assessment, mine reclamation and mine site closure have been dealt with.

Jan 1, 1995

By Hakan Uyguçgil, Beril Bayraktar, Adnan Konuk

In mining, which is one of the industries with the highest risk of occupational accidents, a primary goal is to enhance safety through the thorough investigation of accidents using reliable methodologies. In this research, the data from 13,653 accidents reported in the Karadon Hard Coal Enterprise between 2000 and 2011 were analyzed and compared using the life-table and Kaplan-Meier methods. Accident records were classified and analyzed into four categories: environment-related, equipment-related, person-related and other accidents. Findings in terms of survival time indicate that environmentrelated and person-related accidents had the highest risk in Karadon, with equipment-related accidents having the lowest. This study established the reliability of using survival analysis methods to investigate occupational accidents in the mining sector. Given that environment-related and person-related accidents occur in a relatively short period, such as one year after starting work, it is recommended that research be done to improve workplace and occupational safety measures and broaden the training given to miners. Additionally, it is determined that increasing the use of automation and mechanization in underground coal mines, combined with developing a thorough equipment safety training program to raise awareness of the danger, can help prevent person-related occupational accidents caused by the interaction between equipment.

Feb 1, 2024

By X. Wu, E. Topuz

Booster fans have been extensively used in underground mines throughout the world. In the United Kingdom, S. Africa, Germany, and other countries, many non-coal and coal mines employ booster fans. These fans help to reduce air leakage, to provide an improved flow distribution and to reduce the overall cost of mine ventilation. Although booster fans have not been used in coal mines in the United States, a recent survey indicated that many coal mines would install booster fans if they were allowed to do so. With the inclusion of coal mines, the use of booster fans in underground mines is expected to increase substantially in order to maintain air quality and quantity requirements. Several techniques are used, with varying degrees of success, in determination of booster fan locations in an underground ventilation network. These techniques include linear programming, critical-path crashing, CPM together with cutset operations, the out-of-kilter method, and simulation techniques. This paper provides a brief comparison of these techniques, and reports on ongoing research for an improved methodology for the determination of booster fan locations.

Jan 1, 1987

By Norman K. Olson

A geologic investigation of mineral resources in South Carolina first began in 1825 when the General Assembly authorized Lardner Vanuxen to conduct a "Geological and Mineralogical Survey of South Carolina." Vanuxen, South Carolina&apos;s first State Geologist, reported in 1826 on the limestones (marble) of the Piedmont which during those early years, were burned in many shall, scattered kilns in the region wherever suitable raw material was available. He also mentioned the possibility of using marl from the Atlantic Coastal Plain province for direct application and enrichment to the soil. Since before the year 1844 industrial minerals in South Carolina have been commercially produced literally from A to Z, asbestos to zircon. The first pub¬lished reports of actual commercial production, not just an occurrence, are referenced in Table 1 for 33 known industrial minerals and rocks in South Carolina. Known or suspected occurrences of undeveloped non-metallic mineral resources in South Carolina await future verification by geologic mapping, sampling (including coring), possible beneficiation, and market analysis. These industrial minerals and rocks include, but are not limited to, special, clay minerals (e.g. bentonitic clays, zeolites and others), sillimanite, argillite (lightweight aggregate), kaolin (alumina) and marl (underground storage and tunneling medium). In addition other non-metallic minerals, once mined but still worthy of reconsideration, include topaz (industrial), heavy minerals, barite, feldspar, and monazite. Finally, possibilities for new reserves, as an expansion of existing mine output, might develop for fuller&apos;s earth, limestone (lime), sericite (finely divided mica), vermiculite, kaolin (paper coating and filling, other filler), and metallurgical gravel. Official South Carolina data from the U. S. Bureau of Mines for 1974 indicated a total value of mineral production of $105.2 million. During 1974 production consisted of cam-on clays, (brick and tile), fuller&apos;s earth, kaolin and vermiculite

Jan 1, 1977

"It’s been 80 years since Charles Warman invented the iconic Warman slurry pump, a pump that revolutionized the mining industry and continues to push the boundaries of pump performance to this day.In honor of this legendary brand, Weir Minerals hosted an event at the end of May in Kalgoorlie, Western Australia. Throughout the evening, attendees relived Warman pumps’ history and gained an insight into some of the future innovations planned.“It was a privilege to share this special night with some of our key customers, past and present employees, and members of the Western Australian School of Mines,” said Ricardo Garib, divisional president of Weir Minerals. “Warman is one of our leading brands. It has truly shaped the mining industry over the past 80 years and is a product we are all very proud of. The Warman pump, invented to solve high wear issues in slurry pumping, created a thriving industrial business that is now the cornerstone of Weir Minerals with more than 8,000 people, and more than 150 manufacturing and service centers across the globe.”Always inventingCharles Warman invented the Warman slurry pump in Kalgoorlie in 1938. It was a hardwearing slurry pump that used replaceable liners and a replaceable impeller, something that had never been done before.“Charles Warman was a visionary and an innovator. The use of rubber lining in the pump was groundbreaking as it reduced total ownership costs, was safer to handle and offered extended wear life in many abrasive slurry applications. It is a great example of solving customer problems with material science, and is still taught in universities today,” said Marcus Lane, global product manager for centrifugal pumps at Weir Minerals.It was quickly adopted throughout the goldfields in Western Australia and by the 1950s, as customer demand rose, Warman expanded his business by opening offices in Sydney and Perth.During the 1960s the rapid growth of the business continued with manufacturing and sales outlets established around the world. The Warman Series ‘A’ pump was accepted and became a world leader in its field. Further work on the Warman AH pump resulted in the development of interchangeable metal and rubber wearing components."

Jan 9, 2018

By C. P. Wa1ters

This paper is written primarily from the standpoint of the miner and consumer of Missouri fireclays in refractory products, principally firebrick used in the linings of blast furnaces, hot metal transfer cars, the recuperators of glass melting tanks, and other allied uses involving contact with liquid metals and reactive slags. For these uses the manufacturing plant requires forecast of certain physical characteristics, as well as chemical characteristics, of the raw clays as a determination of practicability of mining, treatment such as pre -firing or calcining, and final usage area. These methods and results may leave something to be desired from an academic view, but are used my operation as an on-running guide to seeking and mining raw material. The high quality fireclays of Missouri are generally differentiated by the user as the softer, somewhat plastic, "bond" clays and the so-called flint clays suitable for a fired or unfired aggregate portion of a brick composition. The semi-plastic "bond" clays are mined in a producing area of northeast Missouri including Montgomery, Audrain, Callaway, Monroe, and Lincoln counties. In this geographic area the clays are the members of the cheltenham formation and occur in rather large lenses in which the usable members may approach 15 meters in thickness and an area of 6o to 8o acres. Overburden is dependent on the surface topography and, in our operations, varies from 8 meters to 25 meters. It can be up to 36 meters in the prairie uplands, but this is rarely strip mined. There was former mining by shaft and drift methods in which the overlying coal was also worked. These clays are primarily used as a binding material for other clay aggregates and is characterized by its lower refractoriness-cone 3o (165o c) to cone 321/2 (172o c), in terms of pyrometric cone equivalent, and an alumina - Al2o3 - content of plus or minus 31%. Physically, these clays are readily slaked by water to a fine grain size and exhibit a degree of

Jan 1, 1977

By Angelus S. C. Owili-Eger

Although the foundation of a unified treatment of fluid flow in variably saturated porous media was established more than seventy years ago, no serious attempt was made to develop it until the early 1970&apos;s. Ever since, a number of unsaturated-saturated numerical models have been reported in the literature. However, none of these models have treated multidimensional, multiphase flow in deforming media, parts of which may undergo extensive secondary fracturing. A situation such as this is not uncommon in coal mining operations in which the longwall method of extraction is employed. The present model has been structured to handle such physical systems. This paper presents the mathematical formulation, the numerical algorithm, and a further validation and evaluation of the modified model. The model treats a multiphase flow in a three- dimensional regime and handles mining excavations of complex and changing configurations.

Jan 1, 1980

By Karl H. Gehring

According to the increasing importance of boom type roadheaders in tunnelling essential problems occuring in the application of these machines are dealt with. Based on a chart including the various stages for decicion finding the excavation method of underground cavities, both the technical limits and economic criteria are discussed in order to determine the range of applicability of roadheaders. Giving examples-the numerous developments in the fields of pick and cutting technology, performance data of boom type roadheaders in hard rock, safety technology and increase in the machines&apos; degree of utilization, research and development of VA is illustrated. Two topic operation examples show partial aspects of the various tendencies of development.

Jan 1, 1981

By J. B. Hiskey, V. P. Atluri

Resin-in-leach (RIL) cyanidation experiments were performed on a refractory carbonaceous gold ore. The objective of this investigation was to determine if strong-base ion exchange resins could adsorb the soluble aurocyanide complex in preference to natural "preg robbing" organic constituents. Direct cyanidation of the carbonaceous gold ore used in this study resulted in less than 2% gold extraction in 24 hr. RIL cyanidation resulted in about 70% gold recovery onto the resin. Kinetic experiments indicated that 50% of the gold is extracted after 1 hr of leaching. Resin breakage was investigated for as-received and preattrited resins. Similar results were obtained with three different strong base resins.

Jan 1, 1990

By M. P. McArthur

General mining practices at W. R. Grace&apos;s Bonny Lake mine are much the same as those used in open pit phosphate mines in Central Florida, except for the difference in the depth of the overburden which introduces many variations, From 1945 to 1961 the mining at Bonny Lake has been from an area in which the overburden averages from 55 to 60 feet and in several locations exceeded 65 feet. The matrix thickness will average 15 to 18 feet for the areas mined. As you can see from the above depths a total hole depth will average from 70 to 75 feet.

Jan 1, 1962