Search Documents

By Y. Luo, S. S. Peng

Based on the concept of slope-stability analysis, a formula for determining an important parameter required in the mathematical model for the prediction of mining subsidence in hilly terrain is proposed. The slope geometry and the physical and mechanical properties of the soil at the surface of the natural slope can all be considered in the formula. Incorporation of this new formula into an existing mathematical model provides an integrated approach for the study of ground movement in hilly regions.

Jan 1, 2000

By D. X. Tang, G. Wilson, Y. Luo, S. S. Peng

Knowing the location of voids/fractures in roof rock will be greatly helpful for roof support design. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way for determining void location in roof rock. In this research, feed pressure and rotation torque are found to be good indicators for identifying the voids, based on the results of a series of laboratory experiments. A set of computational rules has been developed to locate voids in mine roof using the measured roof drilling parameters and implemented in MRGIS, a software package developed to allow mine engineers to make use of the large amount of roof drilling parameters for predicting roof geology properties automatically. Anew feature, 2D map+3D figure display, is also added to MRGIS.

Jan 1, 2004

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The reliable quality assessment of grouting operations is one of the key issues in establishing impermeable grout curtains around shafts, drifts and tunnels. Reliable opera¬tional information on the decrease in the permeability of rock during the grouting process facilitates the assessment of the effectiveness of the completed curtain and assures production quality. Quality control and assurance also fa¬cilitates the early detection and elimination of possible de¬fects in the grout curtain. Thorough control of the grouting process provides the capability to evaluate decreases in the permeability of water-producing fracture zones prior to the beginning or the continuation of excavation of the shaft, tunnel or drift. In order to achieve this objective, post¬grouting hydrodynamic investigations are conducted prior to the initiation or re-initiation of work on the underground workings to measure the decrease in the permeability coef¬ficient of aquifers during grouting operations. 8.1 QUALITY ASSURANCE AND CONTROL OF THE ISOLATION OF ROCK BY GROUTING THROUGH HOLES DRILLED FROM THE SURFACE Quality assurance and control are based on measuring the decrease in the permeability coefficient of water-pro¬ducing horizons as a result of injecting grout into the drill¬holes. For this purpose, the value of the acceptable residual permeability coefficient is calculated beforehand based on the acceptable value of ground water inflow into the shaft, drift or tunnel as specified by the "construction norm and integrated practice (SNIP)" (Anon., 1976). Having ob¬tained the values of aquifer thickness, permeability, and head distribution for each aquifer from flowmetric data (dis¬cussed in Chapter 3), the average value of the permeability coefficient of all aquifers intersected by the shaft is calcu¬lated as [ ] where Ki is the permeability coefficient of the "ith" aqui¬fer; Pi is the pressure of the "ith" aquifer; and M; is the thickness of the "ith" aquifer. The total expected inflow of ground water into the shaft is [ ] where RK is the radius of the contour of influence; RCFB is the radius of the shaft; and p is the coefficient of dynamic viscosity of the ground water. The necessary reduction of the coefficient of permeabil¬ity of the aquifer [ ] where Q is the expected inflow of ground water into the shaft from eq. 8.2; Q.-fin is the acceptable inflow of ground water; and a is the safety factor. By knowing the average permeability value of the rock and the permeability reduction coefficient, it is possible to determine the value of the acceptable residual permeability coefficient for all the aquifers [ ] The values of the permeability coefficient, pressure, and thickness for each aquifer are determined from the data gathered during the hydrodynamic investigations conducted in grout holes prior to beginning the grouting operations as discussed in Chapter 3. After injecting the grout into the first of the holes, the injection into each of the following grout holes is preceded by repeated hydrodynamic investi¬gations. Using the data obtained for each water-producing zone, a graph is constructed where the numbers representing the grout holes in their order of grouting are placed on the abscissa, and the values of the aquifer permeability coeffi¬cient are placed on the ordinate (Fig. 103). This curve char¬acterizes the change in permeability of the given hydro¬stratigraphic unit as grouting operations are completed, one hole at a time. The results of grouting operations are considered to be positive when each sequential observation records a steady decrease in the permeability of the aquifer. The permeabil¬ity measured prior to the injection of the grout into the last hole must be lower than or equal to the acceptable perme¬ability as determined by the application of eqs. 8.1 through 8.4. Table 8.1 presents illustrative data on the hydrogeo¬logic properties of aquifers at a mine shaft prior to the initiation of grouting operations. Data also are presented on the reduction in the permeability coefficient during the in¬jection of the grout. The shaft in question intersects eleven aquifers. Based on data concerning aquifer pressure, thick¬ness, permeability, and the expected inflow rate of water for each of the strata, the average permeability coefficient is calculated according to eq. 8.1 as K = 0.2 x 10-12 m2. The

Jan 1, 1993

By W. Hu

Gravity concentration has been the main method for tin ore beneficiation, based on the significant difference of density between cassiterite and gangue in the tin ore. However, with the exhaustion of rich and coarse reserves, the proportion of tin distribution in slime be-comes as high as 50 to 70% and has a size range of -19 urn. In some sulfide tin ore, most of the tin is of the minus 10-urn size fraction, and thus slime processing has gained importance in tin ore processing. Some innovations are being developed, such as the centrifugal cone separator, belt concentrator, slime table, B-M separator, and slime flotation. Direct flotation with tolyl arsonic acid has been practiced with success.

Jan 1, 1989

By Richard H. Olson

The following discussion will deal with the domestic talc industry only, inasmuch as the writer has had no experience in this field outside of the U. S. This is strictly a geological-mining approach; no attempt is made to assess in depth the effects which milling technology and marketing capability might have in determining the potential of any given talc deposit.

Jan 1, 1970

By Rudolf E. Greuer

Introduction The Institution of Mining and Metallurgy and the Institution of Mining Engineers organized the Third International Mine Ventilation Congress held in Harrogate, England. Sixty-one papers were presented and about 300 participants registered. About 30% of the participants came from Great Britain, 20% from South Africa, and about 5% each came from Australia, Canada, China, France, US, and West Germany. The remainder of the participants came from 18 other countries. Eleven of the papers presented dealt with methane, three with diesel exhausts, four with dust, four with radioactivity, 18 with heat, and 15 dealt with main and auxiliary ventilation. Six of the papers dealt with mine fires, which is a boundary region between main ventilation and gas concerns. Ventilation Congress proceedings are available. See ME, December 1984, page 1687, New Books page. With CH4 and radioactivity topics, the Australians dominated since they are becoming large coal and uranium producers. With diesel exhausts, the most important problem in highly mechanized mines, the North Americans were prominent. The South Africans, working in 90% SiO2 in their gold deposits, were preeminent in presentations on dust. They also led in topics related to heat, joined by the West Germans whose mines are getting deeper. In main and auxiliary ventilation, Great Britain and West Germany provided the majority of contributions. Methane The large number of methods for the precalculation of CH4 liberation in longwall mining all contain three elements: gas content of the coal, gas emitting zone (or influence zone of face), and degree of gas emission. Determination of the gas content, commonly accomplished by taking coal samples, does not pose much difficulty. But this is not the case with the other two factors. Most existing approaches rely on rock mechanics observations. Some only rely on intuition or speculation. The West German coal mines conducted a large research project between 1977 and 1982, in which gas pressures around longwall faces were measured. Gas pressures and gas contents can be related. Therefore, influence zone and degree of gas emission can be determined simultaneously. The precalculation of CH4 liberation in room-and-pillar mining is simpler. Since foot and hanging walls remain essentially intact, gas pressure distribution and gas flow can be calculated using hydraulics equations. A key to these calculations is permeability. A group of Australian researchers reported that the permeabilities of rock under three dimensional stress differs from rock under destressed conditions. This fact was known, but no systematic observations existed. These were provided. Methane drainage has been practiced for more than 40 years. It is used with great success in longwall operations. Some of the West Germans think that methane drainage from the footwall is neglected. Under certain geological conditions, they claim this is as important as drainage from the hanging wall. A research project was presented in support of this claim. Considerable efforts have existed for more than 10 years to use methane drainage in room-and-pillar mining. A paper described the accomplishments of Consolidation Coal Co. Since coal and rock are not fractured as much as in longwall mining, gas transport takes place by the slow diffusion from micropores into the cleats. Then, it is transported by laminar flow along the cleats until a drainage borehole or the mine workings are reached. Boreholes about 300 m (1000 ft) long can reduce the gas content of a band of coal 100-m (330-ft) wide by 50% in one year. A paper from India described methane drainage from gob areas. A French paper reported that especially high methane concentrations can be drained from gob areas if the face ventilation is descensional. Methane buoyancy and ventilating pressures compensate each other, and little air dilution by leakage takes place. Another French paper described a newly developed gas and air velocity monitoring system making use of a microcomputer. Four papers on methane dealt with gas outbursts. Two Australian contributions described the problems encountered with CH,-CO2 mixtures and the attempts to solve them with drainage boreholes having 10 to 20-kPa (1.5 to 3-psi) suction pressures. A Hungarian paper described problems and attempts to reduce the risks of gas outbursts in Hungary. Prediction of gas outbursts in coal seams was the focus of an English paper. Observations show that they are frequent when coal, through its geological past, has become soft and brittle with a resulting increased desorption rate. An instrument for gravimetric de-

Jan 1, 1985

By Leslie C. Thompson

The heap leach process used for recovering gold from oxide and sulfide ores is operated as a closed circuit system in which the cyanide process solutions are continuously recy­cled. In a well-designed operation there is little or no dis­charge of cyanide to the environment. Spent leached ore residues are water washed to remove most of the trace cyan­ides and precious metals remaining after completion of cyan­ide leaching. After the washing step, small amounts of cyanide, metal-cyanide complexes and nitrates remain in the residue. Most of the cyanide and nitrate residue constituents exist in the pore water of the spent ore rather than in the solid mineral fraction. More than 90% of the complexed cyanides in a freshly washed ore residue are present as free cyanide or weakly complexed metal-cyanides. Natural volatilization and decom­position rapidly remove most of these easily dissociable cyanides from the spent ore. Only the stable, strongly com­plexed metal-cyanides, such as gold, cobalt or the ferrocyan­ides and other constituents such as nitrates have a long term persistence in the spent ore residue (Towill et al). Despite washing and natural removal mechanisms, spent ore has the potential to act as a point source of com­plexed cyanides and nitrates for soil and groundwater con­tamination if inadequately contained (Huiatt et al). The groundwater contamination is caused by the leaching of the soluble cyanide compounds and nitrates from the pore water of the residue.

Jan 1, 1990

By Andrew Hall

Many Latin American countries are facing a scarcity of water. As such, infrastructure decisions are quite different from those made in parts of the world that experience a positive water balance. In the latter case, the water treatment approach tends to be ?treat and discharge.? For Latin American regions facing the challenges that go with a negative water balance, the focus is on resource optimization and reuse. Historically, the water challenge has had a significant impact on economic development in Latin America, especially in sectors such as mining, where water usage is high. At the same time, countries such as Chile and Brazil are major development targets for mining and oil and gas operations. Given the water supply challenge, industry is increasingly turning to technologies and processes that maximize water recovery and reuse. With sulfide precipitation and ion exchange water treatment processes for example, it is possible to treat and recover more than 99 percent of water for reuse onsite. These technologies have been applied successfully in other regions of the world where water conservation practices are essential to economic survival.

Jan 1, 2012

By R. N. Chakravorty, R. J. Kolada

Introduction Spontaneous combustion in coal mining is recognized as a major hazard in terms of safety and economics. A survey by Olaf (1979) revealed that 80% of coal mine fires were caused by spontaneous combustion. Modern mining methods demand a high capital investment. Closure of a working face may then result in a huge loss. Even a short production interruption can prove expensive. Spontaneous combustion may also produce lethal amounts of carbon monoxide, thus posing a serious threat to the health and safety of underground miners. The worldwide recession in the early 1980s resulted in a number of mine closures and production cutbacks. So large stockpiles at mine sites were common. Experience has shown that stockpile fires are difficult to extinguish. Critical factors influencing spontaneous combustion There is no simple method of predicting whether a particular mining method applied to a specific coal seam will result in spontaneous combustion. Under favorable conditions of heat accumulation, spontaneous combustion can occur with any type of coal. It is known that subbituminous coals are more susceptible compared to low volatility bituminous coals, and that a high ratio of exinite increases the risk. However, the inherent moisture content of the coal and the exposed surface area may be more significant. Actual mining and ventilation conditions also strongly influence susceptibility. In practice, the experience gained with the mining method applied to a particular type of coal seam must be carefully evaluated with respect to the factors responsible for spontaneous combustion. Feng, Chakravorty, and Cochrane (1973) summarized the critical factors influencing spontaneous combustion in coal mines (Table 1). Prevention methods and strategies Mine layout is the most important factor preventing spontaneous heating. Working districts should be designed so that a particular section can be isolated on short notice without affecting production in others. Sites for preparatory seals should be identified and marked during planning. With coal seams that are highly susceptible to spontaneous combustion, the retreat method of working is preferred. This is because the gob is not subjected to a large difference in ventilation pressure. Coal pillars should be designed to resist excessive crush. The panel system of working is preferred, particularly for mining coals susceptible to spontaneous combustion. The size of each panel is calculated based on the incubation period and the rate of extraction. Controlling air leakage is also important for controlling spontaneous combustion. This is usually achieved by minimizing ventilation pressure difference, proper siting of doors, and avoiding unnecessary stopping and starting of fans. Air leakage is also reduced by sealant coating, injection of cements in cracks and crevices, and by maintaining good gateside packs. Application of inhibitors to control spontaneous combustion met with limited success. Chamberlain and Hall (1973) concluded that borate solution or Montan powder sprayed in the gob area or infused into a low rank coal would reduce the possibility of spontaneous combustion. Early detection of heating Significant research is being conducted worldwide to develop methods for early detection of heating. Monitoring combustion products during the early stage of heating is the most suitable method for detecting spontaneous combustion. The major gaseous products resulting from low temperature oxidation of coal are carbon dioxide, carbon monoxide, and water vapor. In mining operations, carbon dioxide monitoring is considered unsuitable because there are sources other than spontaneous heating from which this gas may originate. Carbon monoxide, however, is a more specific product of combustion during low temperature oxidation of coal. Over the years,

Jan 10, 1988

By M. D. Johnson

Mina Santa Rosa, in west central Panama, is the first large-scale gold mine in Panama and will soon be the largest single-mine gold producer in central America (Fig. 1). At full production, the mine will process 1.8 Mt/a (2 million stpy) of ore and produce more than 1.8 t/a (60,000 oz/year) of gold and 9.3 t/a(300,000 oz/year) of silver. Mina Santa Rosa is a subsidiary of Greenstone Resources of Toronto, Ontario. Freeport-McMoRan geologists first visited the area in 1985. Their rock chip sampling adjacent to old shafts and adits confirmed widespread gold and trace element geochemistry anomalies. Surface mineralization appeared to be localized in and adjacent to narrow veinlets. However, they recognized astructural setting similar to the Nevada Tertiary volcanic-hosted epithermal gold systems.

Jan 1, 1996

Maptek I-Site laser scanning expertise and software technology is being used to map the geology and layout of the deepest underground laboratory to be established in the U.S. The Deep Underground Science and Engineering Lab (DUSEL) in the former Homestake gold mine in Lead, SD, will provide for scientific studies in particle and nuclear physics, geology, hydrology, geo-engineering, biology and biochemistry. The project, funded by the National Science Foun¬dation (NSF), will allow geoscientists and engineers to research the behavior of subsurface rock, minerals, water and energy sources

Jan 1, 2010

By J. G. Wargo

In situ leaching of disseminate gold deposits has been studied from a theoretical perspective to outline the operating environment for the process. Rock permeability and the relationship of permeability to the site of gold particle deposition are key factors in predicting the efficiency of in situ leaching. Permeability measurements, however, have rarely been made during gold exploration, so that secondary geologic features of the deposit must be used. This paper examines some of the geologic characteristics of disseminated gold deposits and comments on the problems and possibilities of in situ leaching of gold.

Jan 1, 1987

By K. M. O’Connor

Time Domain Reflectometry (TDR) is a pulse testing technique developed by the telecommunications and power industry for use in locating breaks in cables. Variations of this principle have been utilized in applications pertinent to closure and reclamation of coal operations. This paper focuses on applications of TDR technology in the mining industry including monitoring of slope movement, abandoned mine subsidence, ground water levels and subsurface LNAPLs, landfill cover performance, and consolidation of mine tailings. TDR technology has been particularly effective for remote automated monitoring, and alarm systems have been implemented for monitoring subsidence.

Jan 1, 2003

By David C. Grant

During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. Mter mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other chemicals (i.e., uranium and selenium) which are mobilized during the leach process, have also been found in the post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and thus greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid improvement in permeability.

Jan 1, 1982

By K. N. Han

The leaching behavior of palladium in ammoniacal solutions was investigated by using the rotating-disk technique in an autoclave. The study included the effects of rotation speed, temperature, oxygen pressure, composition of ammoniacal solutions and catalysts on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in terms of the thermodynamics and a kinetic model. Even though the Eh-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was very slow at temperatures below 100 °C but was significantly improved at higher temperatures. It was also found that the rotating speed of the palladium disk had no effect on the leaching rate. The apparent activation energy was found to he 69.7 kJ/mole. Based on the results obtained, it was concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1999

By Wilbur I. Duvall

This paper discusses general principles of underground opening design based on the concept that with the necessary input data regarding the geology of a site, the physical properties of the rocks, the in situ stress field in the rock and the general geometry of the underground openings, the rock formation can be classified into six major categories which are useful for design purposes. Using simple theories for the criteria of failure for rock In compression and tension, general elastic theory for stress concentration around openings and In structures, beam theory for stability of roof rock, and elementary inelastic theory for creep phenomena, basic design techniques are outlined for the various rock classifications. The need for field evaluation of the theoretical design is stressed and some general techniques that should be used in these field evaluations are discussed. Where appropriate, the need for additional studies and research is noted.

Jan 1, 1977

By W. G. Fischer

Trona ore at the Westvaco mine of FMC Corporation has been obtained by room- and-pillar methods since the mine began operation. The flat-lying, 10-foot bed of trona, Na2CO3 NaHCO3 2H2O, is covered by 1500 feet of weak shale and sandstone. Extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early 60's forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans' were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. Roof cones troy in the longwall methods appeared to be more satisfactory than that found in room-and--pillar techniques. It was therefore felt that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 1, 1966

By Jerome E. Grader

Special-purpose analog computers are being profitably applied in the process industries to perform miscellaneoas online computing functions in situations where conventional measurement and/or control hardware cannot perform a required task satisfactorily. This paper will discuss the application of such equipment in the mining industry. It is divided into two parts, beginning with a description of operation of the hardware, followed by a discussion of several applications of the computers to mining industry control problems.

Jan 1, 1969

In addition to capital and operating costs, the accurate estimation of ore reserves is a key component to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by the improper estimation of ore reserves. The accurate estimation of an ore reserve relies heavily on an understanding of the geology and the underlying assumptions unique to the estimation techniques being used. These assumptions are reviewed, and the shortcomings of the estimation techniques and their possible impact on a given project's economics are discussed. The latest developments in geostatistics in overcoming existing reserve-estimation problems are presented.

Jan 1, 1998

By V. V. Ershov

Mining geometrical graphic documentation is employed on a large scale in designing and planning of mining operations at all the stages of exploitation. Mining geometrical modelling of mineral grade distribution presents an independent type of mathematical (graphic) modelling. The idea of functional relationship between geological indices being observed, and spicier coordinates is the basis of traditional mining geometrical modelling. Graphic presentation of three independent variables P =f (x,y,z) is confined to obtaining the series of two independent variables functions. Independent variables are presented as topographic surfaces corresponding to plane cross-sections of a deposit. During exploitation of certain parts of a deposit the most reliable geological information is obtained, characterizing regularities of ore distribution in the entrails. This information is, though, not taken into account in goemetrization of the new areas. In this connection dynamic modelling of deposits in the process of exploitation is necessary, i.e. geometrization of the deposits should be dynamic.

Jan 1, 1986