Search Documents

By Lynn B. Hales, John A. Herbst, Thomas L. Gabardi

A system for a continuous determination of the charge volume of grinding media in ball mills and SAG mills has been developed. The system, comprised of a unique measurement device and a model based Kalman filter algorithm, determines grinding media level within a mill and calculates media and liner wear rates. The signal from an instrumented washer mounted on the exterior of the mill shell is used to provide the measurement that, along with mill power and on-line models for media mechanics, result in estimates of mill parameters that can be used in media addition control strategies. Data are presented for a 12.5 x 15 ft. ball mill.

Jan 1, 1990

By J. E. Chilton

Methanometers with catalytic heat- of-combustion sensors used in coal mines today will read low for flammable gases when oxygen (0,) concentrations are low or when methane (CH,) concentrations are greater than 10%. Thus, these methanometers may not be reliable during operations such as fire fighting or recovery of sealed mines. The U.S. Bureau of Mines developed a total flammable gas detector (TFGD) to measure CH, at concentrations up to 100% and to measure flammable gases in low 0, concentrations. This paper describes the operation and construction of the TFGD and discusses measurements of flammable mine gases obtained from a mine in western Pennsylvania.

Jan 1, 1992

By Gurses Oner

In situ leaching is a relatively old mineral extraction method; however, historically only a small portion of copper has been produced from small scale operations. Recently, in situ leaching technology because of its intrinsic advantages over conventional mining and milling is being considered as a viable option for recovering copper from both low grade oxide and sulfide deposits. This paper presents the application of computers to investigate in situ technology using large whole core leaching experiments. Computers were applied to three different areas: (1) experimental control and data acquisition, (2) non-destructive evaluation of samples using x-ray computed tomography and image processing and (3) mathematical modelling and data analysis.

Jan 1, 1992

By A. L. Putz, G. Ladouceur, A. R. Laplante

A laboratory centrifugal concentrator was used to evaluate two gravity circuit configurations treating a flash flotation concentrate at a Canadian gold mill. The Initial circuit consisted of a 76 cm (30 Inch) plant Knelson Concentrator (PKC) for coarse gold removal. Later, a hydroseparator and spiral were Installed, with the hydroseparator underflow feeding the spiral and the spiral tailings plus hydroseparator overfiow reporting to a 51 cm (20 Inch) PKC. Gold recovery In the 76 cm PKC averaged 45%. Gold was recovered consistently In all size fractions greater than 38 µm, where recovery dropped to 22% for the -38 µm material. Changing the circuit to Include the hydroseparator and spiral decreased the Knelson unit recovery to less than 17%. The decrease was attributed to the spiral which recovered much of the free gold ahead of the Knelson and to changes In the mill feed (free gold portions were finer and less abundant). The spiral demonstrated erratic behaviour although It still recovered significant coarse gold (+75 µm) yielding unit recoveries of 18-44%. Although mechanical difficulties were experienced with the 76 cm PKC, Its performance was superior to that of the hydroseparator, spiral and 51 cm PKC configuration. Much of the gold In the ball mill recirculating load was found to be too coarse for significant recovery In the flash flotation cell and should be recovered by gravity from the cyclone underflow or ball mill discharge. The LKC proved to be a successful device to evaluate gravity recoverable gold content. Dilution of test samples with silica further enhanced this methodology.

Jan 1, 1993

By C. F. Meyer

The recirculation of mine air in an underground colliery, has always been regarded as a hazardous practice in South African collieries. The Mines and Works Act and Regulations states that fresh air, flowing Into an underground section, must flow out directly into the return airways after being utilized once in the section. One of the largest producing underground collieries in South Africa, Initiated a project on controlled recirculation with the permission of the South African Government Mining Engineer. The project involves the recirculation of 65 m3/s of air inside a ventilation district which serves a total of six production areas. The aim of the project was to increase the airflow to the sections without altering the existing ventilation system. Tracer gas studies were carried out to determine the actual distribution of the recirculated air to the individual areas. The results showed that an effective 54,18 m3/s of the recirculated 65 m3/s reaches the sections. This gives an air utilization figure of 83,4 per cent. Dust surveys were also carried out as part of the project to determine the effect of the recirculation of the return air on airborne dust levels. The results showed that the dust levels remained constant in the main intake and return airways and that no hazardous situation was being created. The project proved to be successful and showed that controlled recirculation can be executed and used as a solution for the supply of air to sections without endangering any lives.

Jan 1, 1993

By F. Touboul, M. Thiercelin, K. BenNaceur

Introduction The need to develop accurate predictive hydraulic fracturing simulators arises from the consideration of vertical containment for the fracture. Fracture height growth from a pay zone into adjacent layers has been shown (see Cleary [I]) to depend on three sets of parameters for the different strata: - elastic properties, - closure stress variations, and, -fracturing fluid leak off, and poro-elastic stresses. Qualitative analysis of the effects of these parameters has been reported in the literature. The first effects were described by Van Eekelen, using simple elasticity considerations [2]. The effect of stress variations was described numerically by Simonson and a1. [3] and experimentally by Thiercelin [4]. Effects of back stresses induced by fluid invasion on fracture propagation were considered by Cleary [5]. In order to couple these effects, a numerical code al- lowing the simulation of three dimensional growth of a hydraulically induced fracture has been developed with the ability of representing the effects of heterogeneities on fracture lateral and vertical extension. The model is based on a new variational formulation of the boundary integral representation of three-dimensional elasticity. The fluid flow and elasticity equations are solved using a moving mesh representation which offers enough flexibility to enable the simulation of any closure stress distribution. Simpler models representing fracture height growth (P3DH models) have been developed [6] [7] that approximate the fracture by a series of one dimensional segments, and the limitation of such approaches is examined in this paper. 1 Description of the model 1.1 Fracture Geometry Hydraulic fracturing simulations involve the coupling of solutions to elastic deformations, fluid flow in the fracture, and fluid leak off into the formation. Since the use of direct solution techniques (i,e,,3D finite elements) is prohibitive, the method used in this study is baaed on a boundary integral representation of the 3D elasticity equations. 1.2 3D Models The classical representation of the problem of a fracture in an infinite medium by boundary integrals is [8]: [ ] where u is the unknown displacement field, r n is the traction operator, I? is the fracture surface, and K is the Kelvin tensor of fundamental solutions to the elasticity operator. Using the notation: [ ] for the displacement discontinuity (or fracture width), one can attempt to solve the boundary integral relation using surface integrals (91 or the displacement discontinuity technique, first introduced by Crouch [lo], and extended to three-dimensional problems [Ill. However, numerical problems arise since the Kelvin tensor has a singularity in

Jan 1, 1986

By Jan M. Mutmansky, David R. Kalasky

Computer simulation continues to be one of the most successful analytical applications of computers in the mining and mineral processing industries throughout the world. Through simulation, managers and engineers can explore the impact of new technologies, equipment designs, plans and operating strategies to improve their operations. It is not uncommon for a single simulation application to provide a quick payback of analysis expenses (within weeks or months) yielding long-term financial and operational dividends. The paper will present a summary of the types of software systems that are available for use on PCs and other computer systems. Support software for curve fitting, statistical analysis, and optimization of simulation models will also be presented. Methods of leveraging simulation efforts through networking and coupling of software systems will be discussed. Finally, the trends in simulation in the mineral industries will be analyzed. Areas of strength and weakness of simulation will be discussed along with the usefulness of commercial general-purpose and custom-writ- ten simulation packages. The future possibilities for simulation in the mineral industries will be outlined and predictions on trends for the future will be presented.

Jan 1, 1996

By G. T. Lineberry, B. R. Yama

Artificial intelligence research has produced several tools for commercial application. Some of the techniques that are widely used today include neural networks, fuzzy logic and expert systems. Artificial neural networks (ANNs) are excellent predictive, pattern recognition and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process-control applications. Modeling of spatial data, ore-reserve estimation, tunnel design, long wall-stability prediction and geologic roof classification are additional applications in which neural networks have been applied successfully. In this study, a standard back propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, the performance of the network is measured on an independent validation set. Results indicate a mean error of less than 1 % between the actual and predicted values. A neural network model was developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values for given coordinates. The neural network not only performed satisfactorily, but in some cases performed even better than the kriging model.

Jan 1, 2000

By D. Zaharaki

In the present experimental study the geochemical stability of inorganic polymers was studied by immersing them in various solutions (distilled water, seawater and 0.5N HCl) for a period of 7 months. Inorganic polymers were synthesised by mixing ferronickel slag with kaolinite, potassium hydroxide and sodium silicate solution. The cement like paste was heated at 80 °C for 48 hours and left for curing at room temperature. Their structural integrity was assessed by compressive strength testing after subjection to freeze-thaw cycles as well as high temperature heating. XRD studies were carried out in order to identify new formed phases and provide useful information regarding the progress of the mechanisms involved.

Jan 1, 2008

By S. S. Peng

Horizontal stress is an important factor that contributes to roof failure during longwall entry development, especially when the immediate roof is weak. In this paper, the effects of stress angle between the maximum horizontal stress and entry development and stress ratio of the maximum to minimum horizontal stresses on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method. The results have confirmed that stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the stress angle is about 60° to 75° . The stress ratio has also some effects on the roof stresses.

Jan 1, 2000

By Y. Nakahiro, T. Wakamatsu, M. S. Elsalmawy

The flotation of quartz, feldspar and alumina was studied as a function of pH when using N-alkyldiamines as collectors. The lengths of alkyl chains of diamines were 8, 9, 10, and 12 carbon atoms. It was found that shorter hydrocarbon chain length of alkyldiamines has stronger tendency to float quartz while the feldspar responded poorly to flotation with these collectors at high pH values. The effect of addition of nonionic surfactant of Brij type, when using dodecadiamine as collector, was investigated. Flotation studies in the absence and in the presence of sodium dodecylsulfonate were carried out. These studies have indicated that sodium dodecylsulfonate, in the concentration studied, functions as strong depressant for feldspar.

Jan 1, 1995

By J. Bigu

Use has been made of several theoretical models to predict radiation levels in underground uranium mines. The models used are the Evans model, the Thomas-Epps mine model, the isolated mine model, the mine tunnel with no air flow and the mine tunnel with air flow (Beckman and Holub). Calculations based on the above models have been extended to include thoron gas and its progeny, a common occurrence in some Canadian uranium mines. Theoretical predictions include radon and thoron progenies WLs and concentrations, and some ratios of great practical interest. The main differences between the models are pointed out and comparison is made with experimental data gathered during the last three years in several Canadian underground uranium mines.

Jan 1, 1981

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

By Y. G. Zhang

Interactive Dynamic Optimization Method (IDOM) will be presented in this paper. IDOM combines inventory theory, dynamic programming, computer simulation and interactive technique to formulate a production schedule for open-pit mines. This new method has been successfully used in metal mines of China for years.

Jan 1, 1986

By Didier Michel, Jean Frenay

Integration of amino acids in the thiosulfate gold leaching process has been noted in the literature. This paper presents a theoretical justification of this integration and demonstrates how amino acids can reduce the thiosulfate consumption of the process and contribute to the stabilization of the leaching system.

Jan 1, 1999

By J. J. Moore

Combustion synthesis, or self-propagating high-temperature synthesis (SHS), reaction systems are discussed with respect to thermodynamics and kinetics. In particular, the effect of the process parameters, e.g. particle size, [All] ignition and combustion temperatures, on these self-sustaining reactions is discussed. Combustion theory is used to investigate the effect of the overall actuation energy of the SHS reaction on the combustion front propagation rate and in obtaining a clearer understanding of the transition from stable to unstable propagation. Finally, examples of the application of combustion synthesis to advanced materials processes are made, in particular the synthesis of Ni-Ti-X intermetallic shape memory alloys, TiC-AI2O3 and ZrB2-AI203 ceramic composite materials.

Jan 1, 1992

By R. K. Singhal

A variety of mining equipment is used in the mining of oil sands by surface mining. This includes bucket wheel excavators, draglines, hydraulic shovels and off-highway trucks. This paper examines the existing mining schemes and equipment used Peculiarities of oil sands surface mining and their influence on equipment selection, utilization and mining schemes are described. Recent developments undertaken to improve mine productivity are also dealt with together with some notes on proposed measures to obtain further gains in productivity.

Jan 1, 1985

By Salama

In the conventional approach, the separator feed incremental masses are assumed to be concentrated at the midpoints of the density or size intervals and subjected to a model partition function. The resulting separation predictions would change if the locations of the incremental masses were changed. As a result. the predicted results depend on the choice of locations where the feed incremental masses are concentrated in the density or size intervals. A technique that utilizes the cumulative-mass-distribution of the circuit feed and the derivative of the partition (separation) function relative to density or size variables is proposed. The proposed technique eliminates the dependency of the predictions on choice of where the feed incremental masses are concentrated within the density or size intervals. Since the proposed technique is based on the cumulative masses at the upper limits of the density or size intervals, the technique produces a single prediction whereas the existing techniques produce predictions that depend on where the incremental masses are concentrated. In fact, it has been demonstrated that the existing conventional technique, in which the incremental masses are concentrated at the midpoints of the density or size intervals, is a first-order approximation of the technique proposed.

Jan 1, 2002

By J de Cuyper, V. M. Lovell, W. Freyberger

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysacchar- ides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By Rudy Rogers

When Gas hydrate formation rates have two steps: a nucleation induction step and an agglomeration step. Hydrate induction in distilled water is extremely slow because of lack of nucleating particles. Our laboratory found that synthetic anionic surfactants greatly improve both hydrate induction and agglomeration because the surfactant?s hydrophilic head absorbs water molecules and the hydrophobic tail absorbs hydrocarbon gas molecules, creating necessary nucleation sites. Vast hydrate deposits inhabit seafloors. What is the seafloor hydrate nucleating mechanism? We find that nano-particles of smectite clays (bentonite and nontronite) are hydrate-nucleating sites in sea-water-saturated, packed porous media, especially when trace quantities of anionic biosurfactants adsorb on the clay particles. Microbes and their bioproducts proliferate around seafloor gas hydrate accumulations. The seafloor microbe-mineral-hydrate synergy is explored in this paper. Keywords: gas hydrates, biosurfactants, crystal nucleation, smectites

Jan 1, 2008