Search Documents

By G. E. McClelland

Introduction Many discoveries have been made during the-past decade of low grade gold-silver deposits in the western US. This has stimulated development of low cost cyanidation procedures for precious metal extraction. Heap leach cyanidation techniques possess considerable potential for application to these low grade ores, small ore bodies, mine strip waste, and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successful, these resources must have good permeability to achieve uniform distribution of the cyanide solution throughout the heaps. Some of the most difficult of the gold and silver ores to treat successfully by heap leaching are those containing excessive amounts of clays, or fines generated by crushing. Presence of excessive amounts of slimes, -50 µm (-270 mesh), in the heap leach feed will slow percolation, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap. This causes the leach solution to run off the sides of the heap rather than penetrate the ore bed. The problem of heap leaching ores with fines can be aggravated while preparing ore heaps because of the natural sorting of coarse and fine material that occurs. This phenomenon results in concentration or ore fines in the center of individual ore piles and concentration of larger rock fragments of the lower slopes and base of the pile. When the individual piles within the heap are leveled off for the installation of the sprinkling system, additional segregation occurs as the fines sift through the coarser ore particles. This results in localized areas or zones with marked differences in permeability. Consequently, the leach solutions follow the course of least resistance. They percolate down through the coarse ore regions and bypass or barely wet areas that contain large amounts of fines or slimes. Effective use of marginal gold and silver resources by heap leaching required development of new methods to achieve more uniform size distribution when preparing ore heaps and better slime control during leaching. Early methods Agglomeration and balling of crushed ore to produce a porous and more uniform feed material for heap leaching is a viable method for treating clayey ores. Researchers from the US Bureau of Mines in Reno, NV began agglomeration pretreatment research in the mid-1970s for applications to and exploitation of these poor percolating feed materials. Little attention had been given to such methods before the Bureau's research. In 1905, T. C. Scrutton developed a unique technique for obtaining rapid vat leaching of a clayey ore where the gold was finely disseminated. His technique consisted of rolling the ore down a chute inclined at 60° to form agglomerates or balls readily permeable by the cyanide solution. However, these agglomerates lacked rigidity. And, to ensure good percolation leaching and washing, they could not be bedded in layers more than 1 m (3 ft) deep. If this depth was exceeded, it is difficult to obtain uniform leaching and washing. This results in reduced gold recovery. Shepard and others in 1937 studied the addition of lime and carbon dioxide or calcium carbonate to gold-bearing tailings to form agglomerates suitable for vat leaching. Satisfactory percolation flow rates were achieved in 90 g (3 oz) scale experiments, but the reagent requirements were cost prohibitive. Agglomeration and pelletizing has been used in other segments of the mineral industry. This technique was first used successfully around 1911 for pelletizing iron ores. Since then, agglomeration

Jan 7, 1986

By A. K. Bhasin

The movement of solid particles in a liquid represents an area of interest in many fields of science and technology. Knowledge of the behavior and characteristics of solid-liquid suspensions is of great importance to many areas of mineral processing. In order to characterize a solid-liquid system, the following factors must usually be considered: a) density of the liquid b) rheological properties of the liquid c) density of the solid particle d) size and shape of the solid particle e) volume fraction of solid particles f) relative motion of solid particles and liquid phase Other variables such as the effect of the containing vessel walls, Brownian movement, inter-particle friction, fluid slip and electrostatic effects, are important in special circumstances. Thus it is evident that a complete theoretical treatment is not possible covering all situations. Studies of the kinematic behavior of solid particles in a liquid have been approached by two methods: 1) Assessing the movement of a single particle and extrapolating to a multi-particle system; 2) Modifying the continuum mechanics of single-phase liquids in such a way as to account for the presence of solid particles. The first approach in general utilizes the method of particle mechanics. Extension to a multi-particle system gives rise to very complicated mathematical computation. The creeping motion equations do, however, furnish a practical, useful basis for achieving a uniform treatment and a better understanding of the phenomena. This approach is useful in the study of sedimentation and hindered settling processes.

Jan 1, 1971

By F. Dingwu

The latest technology and novel equipments in kaolin processing industry in China are described in this paper. Some typical experimental results are presented, which include laboratory-, pilot-or commercial-scale tests. The characteristics of kaolin processing technology are summarized, and the developing trends are indicated.

Jan 1, 1995

By Z. D. Hora, W. N. Hamilton

Introduction Some unique opportunities exist for industrial minerals in British Columbia and Alberta. The region's diversified geology, particularly in British Columbia, offers favorable environments for a rich variety of mineral resources. Many minerals have been produced for years. For some, however, the level of production is far less than the potential. Others have had production in the past, but are not currently produced. Still others are known to exist and may have been actively prospected. But they are not yet developed. In addition, a number of speculative possibilities have recently come to light. The potential significance is not fully confirmed, but is suggested in showings in favorable geologic settings. Location and geography British Columbia and Alberta are the westernmost provinces in Canada (Fig. 1). The region overlaps two major physiographic divisions of the country, the Cordillera and the Interior Plains. It also takes in a small segment of the Canadian Shield on the east. The entire territory is greater than 1.6 Mkm2 (618,000 sq miles). Most of British Columbia lies within the Cordillera, a mountainous belt some 800 km (500 miles) wide. The belt is made up of three main physiographic components, the Eastern, Interior, and Western subdivisions. The Eastern subdivision embraces the rugged, linear ranges of the Rocky Mountains, elevations between 2600 and 3300 m (8530 and 10,800 ft). They form a 100-km (62-mile) wide band straddling the BC-Alberta border and extending northwest across northern British Columbia. The Interior subdivision includes several ancient mountain ranges but is dominated by an intermountane plateau area of low relief (average elevation 1200 m or 3900 ft). The Western subdivision is dominated by the Coast Mountains (elevations between 1800 and 4000 m or 5900 and 13,123 ft). These form a band about 175 km (110 miles) wide into which are sculptured the spectacular fiords of the BC coastline. Alberta lies largely within the Interior Plains, a prairie region of low to moderate relief (elevations between 200 and 1200 m or 650 and 3940 ft) formed of nearly horizontal bedrock strata. The Plains surface rises gradually to the southwest toward the deformed belt of the Rocky Mountains, where the bedrock strata are upturned, folded, and faulted. To the east, the Plains merge with the Canadian Shield, which exposes the Precambrian crystalline basement of western Canada. The total population of the BC-Alberta region is about five million people. Minerals, forestry, and agriculture are the primary industries here. It has well developed infrastructures to service these industries. British Columbia is third among the Canadian provinces in metal mining - $1.1 billion in 1985 - and first in forest products. It is also second in hydro-electric power development. Alberta leads all provinces in total mineral production, largely due to its extensively developed petroleum and natural gas resources - $26.2 billion in 1985.

Jan 12, 1987

By J. Bilant, B. Carlson, N. Gow

High Pressure Grinding Roll (HPGR) technology has been evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester, Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data was consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8%, from 61% to 69%, and shorten the overall timing of silver recoveries from 20 years to just over two years. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities is an open-pit silver and gold mine located in Pershing County, Nevada, approximately 26 miles northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7M troy oz silver (Ag) and 51k troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8” ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers. Historical recovery rates of crushed Rochester ore average 61.4% Ag and 95.9% Au over a period of 20 years [1]. These rates were derived from third party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher, and/or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of HPGR technology to metallurgical recovery and heap leach performance of crushed product in an open circuit configuration, as a potential replacement for the currently in place tertiary cone crushers. During these years, HPGR was evaluated in three phases of test work.

Jan 1, 2019

By F. F. Peng

For a given flotation system, the rate-controlling step in fine coal flotation can be the attachment of bubble to the fine coal particles. The probability of attachment depends upon the surface characteristics and the collector adsorption on the coal particle surfaces. Thus, to further improve the flotation rate and selectivity is to alter the distribution of hydrophobicity on coal particles efficiently by applying the effective means of collector dispersion. In order to enhance the combustible recovery and selectivity of fine coal flotation, and lower the amount of collector used in the fine coal flotation processes, four modes collector dispersion/addition techniques are tested. They are direct liquid addition in pulp (mechanical agitation), ultrasonic energy dispersed collector into pulp, atomized collector into pulp and gasified collector transported by air and formation of collector-air bubbles in pulp. The effect of four collector dispersion/addition methods on the floatability of -600 µ m (-30 mesh US sieve) coal samples from four ranks of coals were studied. The ultrasonic energy dispersed collector and atomized collector flotation processes enhance flotation yield and most significantly improve the kinetics of fine coal flotation. The gasified flotation process can increase the selectivity of separation and decrease the collector consumption due to starvation flotation is achieved in this process. The flotation efficiency of gasified collector process is as high as that of conventional flotation. It is because that the effect of the decrease in the combustible recovery is offset by the increase of selectivity. In addition to flotation experiments, induction times of bubble attachment to the bed of fine coal particles for four ranks of coals are measured.

Jan 1, 1992

By David Loomis

Unlike previous gold mining booms in Nevada's Great Basin, the current boom includes a serious commitment to mine reclamation. Many of the smaller mines began reclaiming in the late 1980s but met with limited success due in part to poor soil characteristics. Public land managers and the mining industry began looking for ways to improve reclamation success. One promising technique is suggested by an ongoing research project using sludge biosolids, the solid residue of municipal waste water treatment. During the 1980s, limited space in landfills led municipal governments to search for alternate ways to dispose of their biosolids. The cities of Reno and Sparks, NR and the US Bureau of Land Management (BLM) searched for ways to combine these needs to everyone's mutual benefit. Yet barriers remained. The federal government had major concerns about potential bioaccumulation of metals and contamination of drinking water from the land application of municipal biosolids. The barriers were lifted late in 1991 when an interagency task force led by the Environmental Protection Agency (EPA) issued a new federal policy on the use of biosolids on federal land. The policy encouraged biosolids as a soil amendment to reclaim degraded minelands and invited federal agencies to develop biosolid pilot projects. In response, BLM enlisted the help of American Resources Corp. (ARC) and the University of Nevada, Las Vegas for a pilot study at ARC'S' Butcher Boy Mine near Wadsworth, NR. Although biosolids have been used in mine land reclamation in the eastern United States for 20 years, before this pilot study, none had been used on public lands in the arid Great Basin. Land application of biosolids improves soil conditions by improving nutrient uptake, increasing water retention, permitting easier root penetration and enhancing soil fertility. Biosolids increase ecosystem productivity and can lead to significant improvements in the structure and diversity of plant and animal communities. Thus, land application of biosolids promotes biodiversity.

Jan 1, 1993

By J. Loredo

Asturias, in Northwestern Spain, has an extensive mining history. As a result of these historical mine activities where operations have been usually developed with little control on effluents or emissions (environmental regulation of mining activity has only been introduced recently), pollution has been severe in some areas, specially in Hg abandoned mine sites, which constitute one of the major environmental problems related to mining. In many of these sites, materials stocked in spoil heaps can be considered as hazardous wastes because of their chemistry, content on ecotoxic elements and potentiality to spread these to the environment. In the humid climatological conditions of the region, water and wind eroded spoils are dispersed through the environment by different pathways and occasionally surrounding soils and waters are intensively affected by pollution. According to the environmental risks that these unreclaimed mine sites suppose for human beings and ecosystems, remedial options must be considered.

Jan 1, 2003

By Gregg E. Korbin, Robin B. Dill, Corey T. Dare, Tor L. Brekke, Larry R. Myer

A study was conducted to develop a fundamental understanding of the relationship between the size of an advancing tunnel face, the rate of excavation, and stand-up time in squeezing ground. Stand-up time is defined as the time elapsed after excavation that an unsupported tunnel face will remain stable. Squeezing ground is argillaceous rock or soil that exhibits pronounced time dependence of deformation and strength properties in-situ. A case history study documented the nature, causes, and solutions of several cases of stand-up time problems observed in the field. Then, in the laboratory, a series of physical model tests were performed in which model tunnel size, face advance rate, material properties, and pressure (representing overburden pressure) were varied. Stand-up time was found to increase as advance rate was increased or tunnel size decreased. In addition, an influence of advance rate on the definition of stability ratios was established.

Jan 1, 1981

By A. K. Sheik, W. G. Pariseau

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine-opening stability. Laboratory test data, borehole measurements and geological mapping assisted in the construction of a coupled finite element model of the rock mass. The model was used to make quantitative estimates of rock stress, strain and displacement changes and to make estimates of the water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. The stability of the crown pillars between stopes was of particular interest. The relatively low effective stress and high rock-mass strength showed that water pressure changes were of no great consequence, which is in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific data.

Jan 1, 2002

By J. Tuzson, H. McL. Clark

Introduction Wear of pumps, wet cyclones and pipelines by suspended solid particles will impact their operating economies by limiting their useful life, reducing their reliability and increasing the amount of servicing. Erosion is considered a materials problem. The empirical solution consists of testing different materials in field applications. Such tests are time consuming and expensive. The prediction of localized wear rates, life estimates and appropriate material selection demand a better understanding of the slurry wear process in environments corresponding to those found in working equipment. Key words: Wear, Slurry abrasion, Coriolis erosion tester The slurry wear process Solid particles suspended in liquid generally move with the flow, but such particles deviate under the centrifugal and Coriolis forces encountered in pumps. The concentration of particles will increase, and a solid layer or bed may accumulate if the acceleration is directed against the flow passage wall. Large particles in dilute suspensions may impact the wall. dissipating their kinetic energies and removing material. However, particles smaller than about 11)(1 µm encounter great drag when moving through the liquid. and such par¬ticles have little kinetic energy left when they reach the wall. They cannot penetrate the stagnant boundary layers present in pumps. Therefore, small particles tend to form beds that slide along the wall, removing material by a process that could he called sliding erosion or wet abrasion. Wear by impact erosion from large particles in dilute slurries can he predicted by appropriate analytical and empirical methods. However, laboratory tests and calculations of wear rates that correspond to sliding erosion are more likely to correlate with field experience from wear under similar conditions. Specific energy Data from laboratory slurry erosion experiments have shown that the amount of material removed is approximately in proportion to the energy expended in the erosion process. Thus. the specific energy-energy expended in removing by erosion a unit volume of material-offers a simple, practical measure for the erosion resistance of materials. The concept was found to also apply to sliding erosion (Clark et al.. 1997). Generally, the study of the material-removal process in slurry erosion continues to remain a subject of research. Conceptually, if the flow velocities and accelerations could be calculated in a pump or pipeline, the energy dissipated at the passage walls could also be estimated, and the material removal rate would become known from the specific energy determined by laboratory tests. Slurry erosion testing Laboratory devices made specifically for slurry erosion testing may be grouped into the following: jet erosion devices, slurry pots and the Coriolis test machine (Pagalthivarthi and Helmly, 1992). Jet erosion devices use a slurry pump and nozzle to produce a high-velocity slurry jet that is directed at a flat material specimen, either perpendicularly or at some acute angle. Combined impact and sliding erosion are produced. but the processes cannot be separated, and the wear is difficult to assess except by weighing. Slurry pots consist of a cylindrical vessel containing the slurry of interest. In the slurry pot, test specimens are attached to a rotating arm. The samples are rotated in the slurry and experience local flow conditions that result in combined impact and sliding erosion. Wear depth measurements from detailed laboratory experiments have been successfully correlated with results from an analytical model of the process, and specific energy values have been calculated (Wong and Clark, 1995). In industrial use, the samples are weighed to determine the total material loss. Materials are ranked with respect to some reference material. The Coriolis erosion tester (Tuzson, 1984) consists of a rotor with a central cavity, from which two opposing radial passages lead out (Fig. 1). The slurry is fed to the centerof the rotor in one pass from a stirred overhead tank. The slurry particles are subjected to the Coriolis acceleration as they flow out through the radial passages. The material specimens are mounted into the radial passage walls facing the direction of rotation and are eroded by the particles that are pressed against them as they flow out radially. A narrow groove is worn into the sample within a few minutes, using a few gallons of slurry. Material removal is estimated accurately from profilometer traverses across the wear scar at different locations. The energy dissipated by the particles can be estimated, which leads to a well-defined experimental value for the specific energy.

Jan 1, 2000

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By A. Anttila, S. Persson

The grinding mill is probably the most common unit operation in mineral processing. There is, however, much that can still be done in the way of optimization. This paper discusses the results of a well-controlled pilot-scale test in which the performance of a tumbling mill equipped with a conventional rubber lining and lifter bars was compared to a tumbling mill equipped with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14% more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case, grinding with a -20-mm ball charge required 26% less grinding energy than grinding with a -30-mm ball charge. The energy savings can, in most cases, be converted to an increase in capacity. The wear of the grinding media is difficult to assess over a short test period, but the results suggest that the wear is somewhat less when a smooth lining is used. A determination of the wear of the linings was not included in this study, but it is generally accepted that the use of magnetic linings reduces the lining costs dramatically. Computer simulation using the Millsoft code developed by Mishra et al. confirms and explains the increased effectiveness of comminution when a smooth lining and smaller grinding balls are used.

Jan 1, 2000

By Andrew J. Neale, Brian C. Flintoff

A review of the current literature, combined with the authors' knowledge of the western Canadian coal industry, indicates that the development and implementation of process control in coal preparation, particularly in flotation applications, is significantly lagging behind that seen in mineral processing. The reasons for this include the lack of inexpensive and reliable sensors, incomplete understanding of the flotation process, limited experience of process control in the coal preparation industry and depressed coal prices, all of which have combined to hinder plant automation. This paper illustrates the benefits of process control in coal flotation, provides a general discussion of the control problem and concludes with two examples drawn from Australian experiences.

Jan 1, 1989

By G. Brien, O&apos

Selective in-plant breakage was investigated at a Central Queensland, Australia mine. Component seams and size fractions from in-plant samples were characterized petrographically and probability analysis of vitrinite reflectance data used to track the distribution of seam proportions through the plant. Results show that the 2 seams reported differentially to coarse and fine circuits, mainly as a function of coal type rather than rank. Seams were also preferentially concentrated in different size fractions of the coarse circuit. Breakage in the coarse coal centrifuge generated approximately 4% of -0.5 mm fines, but was not seam specific.

Jan 1, 1996

By J. Lorosch

Improvement of current leaching technology was found necessary when processing ores which are more difficult to leach because they generate highly viscous, air-rejective pulps. Cyanidation of these pulps has to run at low oxygen concentrations if the conventional aeration technique with compressed air is used. Since the dissolution rate of precious metals mainly depends on the concentration of dissolved oxygen in the pulp [1, 4, 5], the kinetics of the gold extraction become slow in such cases, which in turn often leads to a significant decrease in the overall gold output within the conventional leaching time of up to 48 hours.

Jan 1, 1988

By Kenneth N. Weaver

Introduction and Historical Background State Geological Surveys have been deeply involved in industrial minerals from their inception beginning in the first half of the 19th Century. To Massachusetts belongs the credit of having carried out the first Geological survey under state auspices on the Western Hemisphere. One of the causes leading up to this survey was. Governor Lincoln's message to the legislature of May 29, 1830, from which I quote in part: "Much knowledge of the natural history of the country would thus be gained (from a geological survey), and especially the presence of valuable ores, with the localities and extent of quarries and of coal and lime formations, objects of inquiry so essential to internal improvements and the advancement of domestic prosperity, would be discovered.". Similar phraseology is present in practically all of the initial organic acts creating the first State Surveys. High on the list of priorities for these embryo surveys was an inventory of the mineral resources of the State with particular emphasis on the industrial minerals. Prom these early beginnings, the state surveys have developed a great wealth of geological data either directly or indirectly relating to the development of mineral resources. One can gain some conception of the effort that state surveys today place on industrial minerals studies by noting the projects in which they are engaged as reported in the State Geologists Journal. In 1970, for example, approximately

Jan 1, 1972

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 2.4-m (96-in.) diam vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subse¬quently, a field test was conducted in a Colorado oil shale mine during which two 2-m (79-in.) diam fans were reversed. The data obtained indicate that reverse performance characteristics depend on the blade angle and the hub-to-tip ratio. The quantity in the reverse mode ranged from 30% to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1987

By R. Merwin, S. Hoff, A. Ellsworth, M. Zhao, X. Jiang

The choice of mill linings in comminution circuits is critical as it affects grinding efficiency, overall cost, and product quality. As a consequence, a variety of liners have been developed over the years in an effort to increase wear resistance, improve grinding efficiency, and reduce energy consumption. One particular type of metal magnetic lining (MML) was developed in China seventeen years ago and has since been installed in over 400 applications throughout the Chinese mining industry. Most recently, one set of magnetic mill liners was brought to the US for installation into a secondary ball mill used for the grinding of iron ore. Protection of the mill is provided through the magnetic attraction and retainment of worn media, ball chips, and other various magnetic particles to the mill wall. This greatly improves the wear resistance and overall life of the liner. The installation and performance data for the magnetic mill liners in a US iron ore concentrator are presented in this paper.

Jan 1, 2007

By John Armstrong, Michael Savill, David Powell

Hong Kong is an intensively developed region and has the highest vehicle densities in the world. In 2000 there were 6.6 million people and 580,000 vehicles using 1,890 km of road covering the 1084 km 2 territory. The high vehicle and population densities together with the difficult terrain have seen road tunnels emerge as key components both in the current and future road transportation network. Currently there are eleven operating highway tunnels in Hong Kong, seven government owned and the remaining four “build, operate and transfer” franchises, see Figure 1. The very first tunnel was the dual two Lions Rock Tunnel completed in 1967and the latest the dual 3 lane Tai Lam Tunnel opened in mid 1998. Figure 2 shows the alignment and statistics for all 11 Hong Kong tunnels. Looking ahead, Hong Kong has embarked on the study and design of the next generation of major highways and as many as a further seven tunnels are currently under feasibility study or detailed design. This seems an opportune year to produce a broad appreciation of the fire strategy, life safety and ventilation practices in Hong Kong not only for the existing tunnels but the new standards and requirements for the next generation of Hong Kong tunnels. This paper provides an overview of the fire strategy, life safety and ventilation of Hong Kong’s existing and planned tunnels. The paper pays particular attention to the areas where the unique conditions and requirements in Hong Kong impacts on tunnel and systems design and the solutions adopted to overcome these challenges.

Jan 1, 2001