Search Documents

By Winthrop F. Watts, Robert W. Waytulonis

During the 1980's. the Mine Safety and Health Administration (MSHA) proposed new regulations for the use of diesel equipment in underground coal mines, and the National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen", and that reductions in exposure to exhaust pollutants would reduce excess risk. During the same time, the Bureau of Mines tested new emission control technology to minimize diesel emissions. The objectives of this paper are to discuss the major issues regarding diesel exhaust emissions. especially diesel particulate matter (DPM) , and to highlight emission controls that will be available. DPM is a potential health threat because it is respirable in size and is composed of nonvolatile carbon with adsorbed or condensed compounds. These compounds include potentially mutagenic or carcinogenic hydrocarbons such as polynuclear aromatic hydrocarbons and sulfates. DPM contributes to the degradation of air quality in mines with typical mean concentrations ranging from 0.2 to 1.0 mg/m3. In addition to adequate ventilation, control of DPM can be achieved by implemention of improved work practices, regularly scheduled engine maintenance, and emission controls.

Jan 1, 1991

By Robert A. Jankowski, Natesa I. Jayaraman, Jay F. Colinet

The U.S. Bureau of Mines evaluated the dust control effectiveness of two-phase flow systems in a full-scale model mine using a mockup of a Joy 14CM continuous mining machine. In a two-phase flow system, air and water flow simultaneously through the nozzle. Air pressure varies from 10 to 60 psi, and water at 30 to 50 psi. Coal dust was introduced at the face, and dust concentrations were monitored at the operator locations and in the return. When compared with a conventional spray system, a symmetrical two-phase flow system reduced dust levels during the box cut by 43 pct at the operator location, and 30 pct in the face return. Dust levels, however, increased at the off-operator position during the slab cut. A directional two-phase flow system reduced dust levels at both operator locations by more than 90 pct in the box cut mode. While the use of two-phase flow systems will reduce respirable dust levels and water usage, it requires an air supply to the miner. Moreover, the ability of the two-phase flow system to redirect the dust cloud makes nozzle orientation a critical factor.

Jan 1, 1991

By R. Latifovic

Assessment of the possible impact of existing and future mining projects located in remote areas may be difficult and costly. This may have an adverse effect on the process of issuing mine permits and development of new mines. A remote sensing based land cover change assessment methodology presented in this paper is a promising avenue to render this process more meaningful, precise and affordable. It has been applied to a case study of the Oil Sands Mining Development in the north-east of the Canadian province of Alberta. Recently, the Athabasca Oil Sands Region (AOSR) is a place of unprecedented growth of open-pit mining operations. This study was focused on the primary impact onto the landscape and vegetation resulting from exploration and, mining development. This impact was assessed using an information extraction method applied to two LANDSAT scenes. The analysis based on derived land cover maps shows a 8.64% decrease of natural vegetation in the study area (715,094 ha) in 2001 relative to 1992. It is demonstrated that the methodology presented here provides reliable results and is fully applicable for the assessment of the environmental impact of large scale mining operations.

Jan 1, 2006

By G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By C. Anderson, K. Nikkhah

This paper outlines the role of simulation software in design and operation of a typical metallurgical plant with mineral processing and hydrometallurgical units, to produce concentrate and pure metal. It addresses the role of simulation and mass balance software in the conceptual, feasibility and detailed design stages. It discusses the use of JKSimMet for sizing of mineral processing units, and METSIM and IDEAS for development of energy and mass balances. In detailed design of a plant, the complex interaction and variation in performance of various units makes it difficult to predict overall system performance and availability. Simulation is used to: assess operating strategies that affect surge capacities at various stages compare different ore types and mining strategies that affect concentrate product quality. optimize transportation logistics for raw materials, concentrate and metal products

Jan 1, 2001

By D. Zaharaki

The present experimental study underlines the advantages of factorial design in environmental, geotechnical and waste management experimentation. A typical case study regarding solidification of metallurgical wastes is presented and the main effects and interactions of three main factors are determined in order to establish the optimum experimental conditions in terms of compressive strength. Finally, a regression equation that predicts accurately the real compressive strength of a specimen under various experimental conditions is derived.

Jan 1, 2005

By Robert Snow, Yingxue Yu, Howard Hanson, Patrick Zhang

One of the major current efforts by the Florida phosphate industry to reduce deep aquifer water consumption is to use 100% recycle water for flotation. This measure alone could save billions of gallons of deep well water annually. However, this also results in higher suspended solids (slimes) in flotation water, causing poor process performance particularly for amine flotation. Polymers could play a major role in allowing the industry to use high-turbidity recycle water for amine flotation without compromising its impact on the Florida economy. The enhancement of rougher flotation by polymers may also have potential. Most importantly, dramatic efficiency improvement may be realized by floating silica first. Adding polymer to flotation feed and/or water is perhaps the most economically viable way of reversing the Crago "double float" process, in order to reduce operating costs and increase phosphate recovery. This paper presents both laboratory and pilot flotation data showing the effect of different polymers on collector dosage and flotation recovery. There appeared to be an optimal range of polymer concentration beyond which the benefits do not offset the drop in phosphate recovery. The effect of poly mer is slime-level dependent. Pilot testing data show that the "Reverse Crago" process (floating silica first followed by phosphate flotation) can outperform the Crago process.

Jan 1, 1999

By AKIHIRO YOSHIMURA, HIDEKAZU KATO, KOTA TAKATORI, YASUNARI MATSUNO

Chalcopyrite (CuFeS2) is the most refractory copper mineral when treated in conventional sulfate media leaching systems. This study is the first to examine the use of a dimethyl sulfoxide (CH3SOCH3), or DMSO, solution containing copper chloride (CuCl2) in the leaching of chalcopyrite. The DMSO solution containing CuCl2 could selectively dissolve the valuable metals of copper (Cu) and gold (Au) from chalcopyrite while leaving minerals with little economic value, such as pyrite (FeS2), and the penalty element arsenic (As) in the residues. Leaching chalcopyrite using a DMSO solution that contains CuCl2 offers a number of advantages, including eco-friendliness and easy operation.

By S. K. Kawatra, S. T. Bagley, T. C. Eisele

The use of the bacteria Thiobacillus ferroxidans to catalyze pyrite dissolution in coal is well known, and recent investigations have shown that T. ferrooxidans are also capable of rapidly altering the pyrite surface to facilitate its removal from coal by froth flotation and oil agglomeration. However, the effect of reactor design on the bacterial leaching rate is poorly documented, and the ability of bacteria other than T. ferrooxidans to affect pyrite flotation has been unknown. In this study, the effect of a number of different microorganisms on the flotation of unoxidized pure mineral pyrite has been investigated, and it was shown that organisms other than T. ferrooxidans are also capable of depressing pyrite flotation. In addition, comparative studies of leaching in shake-flasks and pachuca tanks have shown that the pachuca tanks allow leaching to proceed to a greater degree and at a significantly accelerated rate.

Jan 1, 1989

By Michael J. Martinson

A powerful methane explosion in the mid-shaft pump station of a main service and ventilation shaft killed several persons on the station; more workers were killed when a mancage travelling down the shaft fell to the shaft bottom under a pile of broken concrete slabs from a brattice wall destroyed by the explosion venting into the shaft and a tangled mass of twisted steelwork from the equipped compartment. The newly-commissioned shaft serves a recent extension of an established mine on the Orange Free State (OFS) goldfield in South Africa. After outlining the circumstances in which the paper was written, and reviewing the nature and extent of the methane hazard in OFS mines, the paper describes the physical layout of the shaft and summarises evidence given by witnesses at the official inquiry concerning events prior to the explosion. No attempt is made to apportion blame for the incident.

Jan 1, 1989

By E. G. Williams

Underclays and shales are two natural resources associated with the coal measures. Underclays are widely used as the raw material for refractory, semi-refractory, and face bricks. Shales are useful for sewer pipe and lightweight aggregate. This study concentrates on the geologic controls over the properties of shales for use in the manufacture of lightweight aggregate, and the geologic controls over the properties of underclays for use in the manufacture of bloating ladle refractories. The industrial processes are similar in that both involve the trapping of a gas phase to cause bloating. They differ in that the bloating of lightweight aggregate occurs at lower temperatures (1000-1200°C) than ladle bricks (1350°-1470°C). Lightweight aggregate bloats during an initial rapid firing. Ladle bricks are manufactured by slow firing at 1100°C for up to 80 hours. Bloating occurs when these bricks are reheated to 1350°C . Bloating shales are those which expand twice or more times their original volume during fairly rapid firing. Commercial bloating is usually done by rotary kiln processing or sintering; in both cases the firing rate is much faster than the experimental rate (5/8°C/minute). Bloating results from the entrapment of gasses which are evolved during firing. The material must have adequate viscosity to trap gas bubbles throughout the temperature range of bloating. The finished product contains a high percentage of closed pores with a bulk density between 35-75 pounds per cubic foot. Expanded shale finds its most important use as a substitute for heavy concrete aggregate (crushed stone, sand and gravel) where low bulk density is desired property. The extent of bloating in lightweight aggregate is a function of the mineralogy and chemistry of the shale. Figure 1 shows a corner of the three phase diagram, kaolinite-quartz-(illite and chlorite). Several areas on the diagram are outlined which contain predominantly marine shales, fresh and brackish water shales, and underclays. Each sample was rapid fired and the resulting expansion was plotted on the phase diagram.

Jan 1, 1973

By J. D. Patsey, G. T. Lineberry

A.E. Hall The authors are to be commended for their attempt to provide a convenient piece of software for preliminary drum hoist specification. This field has received little attention in recent years and is eminently suited to calculation by computer. Unfortunately, there appears to be an error in the calculation of the required rope diameter. The 66-mm (2 5/8-in.) rope selected is oversized for this application. Wire rope weight and breaking strength are related to the rope diameter. For a round strand rope

Jan 8, 1987

By James W. Griffith, Sarah A. Riling

Bituminous coal dust was repeatedly placed into one lung lobe of anesthetized Macaca nemestrina monkeys using a flexible fiberoptic bronchoscope. Radiographs taken at 15 day intervals showed a focal radiographic density after 90 days time when a total of 1 gram of dust had been instilled. The radiographic density progressed slightly in size until 12 months by which time 3 grams of dust had been instilled and the animals were euthanized. At necropsy, the only significant gross lesion detected was the focal black pulmonary lesion located at the dust instillation site. Histologically, the lesion was composed of coal dust laden macrophages located primarily within interstitial tissue and interspersed with a slight amount of reticulum and connective tissue fibers. The distribution of coal dust was limited to the instillation site in the right caudal lung lobe based on radiographic, gross and histologic examination. Bronchoalveolar lavage of both right and left caudal lung lobes was performed 8 times during the 12 month long experiments without significant complications. More macrophages were found in lavage fluid from the right lung than the left, and most macrophages from right lung contained coal dust particles. Based upon a limited physical examination and complete blood count at 15 day intervals the animals remained normal during the experiment. We conclude that the primate lung's response to focal experimental bituminous coal dust resulted in a marked focal increase in pulmonary alveolar macrophages, which can be recovered regularly in high numbers by bronchoalveolar lavage. The model described has significant potential for investigating the pathogenesis of various respirable dust-induced pneumoconioses, for evaluation of new therapeutic approaches, and for refining experimental and clinical diagnostic applications of bronchoalveolar lavage. Key words: Coal Workers Pneumoconiosis, Disease model; Primate, Lung Lavage Fluids

Jan 1, 1991

By Angelus S. C. Owili-Eger

The past decade has witnessed an unprecendented proliferation of groundwater computer models. Some of these numerical models were developed for the purpose of simulating groundwater movement in mining environments and predicting inflow rates into active mines. However, a general acceptance of these models as routine planning tools by the mining industry has been slow. Until recently, the major use of these models in the industry is by consultants. There are several reasons that have contributed to this situation. Some of these factors - include scarcity or non-existence of an appropriate data base information required for executing these models, the difficulty and costs involved in acquiring data, and the fact that the instructions for using these models are often too involved and time consuming. Today, however, the state-of-the-art technology has been advanced to a level where numerical models can be routinely used to simulate and predict inflow rates into active mining environments. Such environments include highly fractured (longwall) and deforming flow media. Features integrated into these comprehensive and yet easy to use models are double-porosity-pressure, multiphase, and non-darcian flow conditions. This paper reviews the role that computer modeling has played in mining-related operations by presenting several case studies and the state-of-the-art tools currently in use. Included will be some of the practical field applications that have been compiled during the past decade.

Jan 1, 1986

By D. E. Walsh, J. T. Hollow, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Because of their gold value, carbon fines are collected by a filter press. Samples of the carbon fines show that they consist of 20% to 30% carbon, 70% to 80% grit and 0.17 to 0.68 g/kg (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in the form of recrystallized free gold grains, with the balance being the adsorbed gold on the carbon. High recoveries of gold and carbon were obtained from the fines in laboratory tests using froth flotation, with a high rejection of the grit. More than 95% of gold and 90% of carbon can be recovered by three stages of gold flotation followed by two stages of carbon flotation. Key words: Gold recovery, Activated carbon, Flotation

Jan 1, 2003

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study was conducted to control iron in copper electrolyte streams using Eichrom Industries' new monophosphonic/sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27-g/L iron and can be readily regenerated. In addition, the new resin can easily be synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydrometallurgical streams.

Jan 1, 2002

By Vanessa M. Torres, Lafayette C. L. Freitas, Evandeo C. Silva

This paper shows two applications of artificial intelligence models in process development. In the first application, a heuristic fuzzy correlation can predict flotation behavior in bench scale based on feed characteristics for a high variability copper ore, as well as to predict plant performance for a feasibility project evaluation, minimizing its risk. The second case study shows the use of neural networks to model the iron ore sintering, correlating ore characteristics and operational parameters with sinter properties. With this application, CVRD aims to establish a new step on iron ore product evaluation and customer support.

Jan 1, 1998

By K. N. Han

The kinetics of gold dissolution in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effects of stirring speed, temperature, oxygen partial pressure and lixiviant, concentrations on the overall leaching rate was investigated. It was found that the dissolution of gold could be represented by a heterogeneous chemical reaction. Under the conditions studied, the apparent activation energy ranged from 34.7 to 54.3 kJ/mol. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1998

By John M. Gullbert

It is the task of this portion of today's session on the new meaning of regional tectonics in the search for ore districts to discuss known interactions of tectonics and ore deposition in the 'new global tectonics' context. I will speak particularly about known applications of the recent tectonic advances to ore finding. Stated yet another way, it's getting on in time toward the "put up or shut up" stage-¬and I would not be here if I thought that the new tectonics were not an effective present matrix for ore finding. Before delving into specific geologic relationships--and I propose to discuss mainly the evolution of an idea which may reveal the presence of a major copper deposit on mainland Mexico--I must note that there have been no published accounts that I know of which assert that a particular discovery has been made soley and specifically because of an interpretation based upon mechanisms directly linked to sea floor spreading or plate tectonics. It is nonetheless true" that several major exploration efforts are based upon such interpretations, and, as is normal when exploration ideas are involved, one does not wish to call attention to an advantageous position in a highly competitive business. Little might be expected to have been announced in so fast-moving and potentially lucrative an area. Another point which needs to be made is that people such as B. S. Butler (1933), Billingsley and Locke (1935 and 1941), Harrison Schmitt (1935), and more recently Mayo (1958) have been working for decades with the tectonic expressions of the emergent tectonics without recog¬nition of the driving forces or the unifying tectonic concepts

Jan 1, 1971

By Violetta Pavlova

Knowledge of geometrical properties of blocks in a hard jointed rock among other things is of considerable importance for prediction of rock mass behavior and for its exploitation. This paper presents a new approach to obtain the information about percentage of blocks with desirable geometrical properties in a jointed rock mass extending through a large region of interest. A model of a rock mass separated by finite number of systems of parallel plane discontinuities which form discrete blocks is discussed. A computational procedure has been derived to analyze the volume and shape distribution of blocks in the rock mass.

Jan 1, 1992