Search Documents

By J. C. Stankus, J. J. McCaffrey, S. Guo, S. S. Peng

An innovative concept in longwall tailgate support is discussed. This new concept utilizes a high-capacity roof-truss system to replace conventional wooden cribs. The first field test was conducted at the Bailey Mine and was very successful. Similar tests were installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data demonstrated that the dynamic roof-truss system effectively controls the various abutment pressures caused by longwall mining. Thus, a stable tailgate entry is maintained

Jan 1, 1997

By J. A. Botín

Mining investment decisions are difficult since decision analysis is often based on scarce information. The sources of uncertainty in large mining investment projects are particularly numerous and are present in all evaluation stages. Hence the feasibility decision for projects of this nature will largely depend on how well these sources of uncertainty are managed to achieve bankable risk levels. The risk associated to the construction stages of a mining project is particularly difficult to quantify, mainly because the large number of variables affecting constructive yields, and the complex interactions among constructive resources. This investigation focuses on developing quantitative simulation models and tools to increase the value of a mining project by means of an optimization of the preproduction equipment fleet. The models were validated through their application in the Chuquicamata Underground Mining Project.

Feb 23, 2014

By R. K. Devala

In this paper, numerical approximation schemes, for solution of the mass transfer problem in mine ventilation have been developed by using three implicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments, using the concept of Root Mean Square error. For implicit finite difference schemes, in general, the modified central difference scheme is better than the two other schemes at lower velocity. Also, at lower air velocities, implicit schemes underpredicted the concentration values. At higher air velocities, the Crank-Nicholson and Laasonen schemes provided better results than the Modified Central Difference scheme.

Jan 1, 1994

By A. H. Leuschner, P. J. Kruger, J. Kruger

INTRODUCTION This paper deals with some practical aspects of the use and interpretation of dosimetric methods for assessing the exposure of workers to natural uranium. Consideration must be given not only to the scientific value of the method of dosimetry, but also to the practicality of the method in the particular working environment. It is generally accepted (IAEA, 1976) that uranium does not present a hazard during the mining and extraction processes up to the final concentration stage, that is precipitation as ADU or calcining to the oxide. Further processing (e.g. conversion to oxides, fluorides, etc.) is generally associated with the nuclear industry. It is customary for uranium processing facilities to be managed according to industrial norms rather than according to those applied for the purpose of radiation protection. This is mainly because of the large quantity of material to be processed and the fact that uranium is considered to be of a low radiotoxicity. Although ventilation is used to some extent, provision is not made for the same level of protection as would be required in a radiochemical facility. It is typical in such a plant to find that the process itself may be enclosed and ventilated, but the ventilation is inadequate to cope with an accidental release of material. The working environment is poorly ventilated, sometimes only by natural ventilation, and one frequently finds areas with high airborne dust levels, designated as mandatory respirator areas. Protection of personnel is dependent on personal protective equipment. Radiation protection is not of prime concern and personnel are not specifically trained in this subject. It is in this type of environment that acceptable monitoring procedures and personnel dosimetry must be established. The effectiveness and practical application of the dosimetry must also be judged against this working environment. DOSIMETRIC TECHNIQUES The methods available for assessing personnel exposure, whether it be in terms of chemical or radiological hazard, include urinalysis, faecal analysis and [in vivo] monitoring. Faecal analysis does not present itself easily as a method for routine use. Techniques for [in vivo] monitoring have been developed recently and as expensive instrumentation is required, it is not generally available. That leaves urinalysis as a dosimetric technique for routine use, and it is probably for this reason that urinalysis is still widely used. Guidelines for the interpretation of urinalysis results, as originally provided by Neuman (Neuman, 1950), are still used in practice, even though it has become clear that this method has severe limitations as regards the assessment of the dose as a result of the intake of class W or class Y compounds (Alexander, 1974). Typically a level of 300 µg [U/C] urine can serve as an indicator of an acute exposure (above which chemical damage to the kidneys may occur) and a level of 100 µg [U/C ] urine can serve as an indicator for an investigation. Such levels are determined and are used in conjunction with several factors, such as mode of intake (ingestion or inhalation), solubility of compound (D, W or Y), means of intake (acute or chronic), environmental monitoring results and frequency of urine sampling. Since the ICRP concept for internal radiation limitation changed from that of the critical organ, i.e. the single organ of greatest significance under the circumstances, to that of effective dose equivalent, i.e. account being taken of the total risk due to the exposure of all tissue, the maximum permissible organ burden (MPOB) was replaced as secondary dose limit by the annual limit on intake (ALI) (ICRP, 1977). The ALI values are calculated from the committed dose equivalents of the various organs, and are used to determine organ burdens, which are then used to interpret the dosimetric results. Using the ICRP model (ICRP, 1979), a comprehensive calculation was made by Johnson (Johnson, 1980), giving organ burdens and excretion data in terms of intake for acute and chronic exposures for different categories of uranium compounds. The question arises as to what extent the direct measurement of intake can be utilised as a method of dosimetry. This will require a method of personal intake measurement for each individual worker, with both ingestion and inhalation being taken into account. A measurement of

Jan 1, 1981

By J. P. McDonald

Exposure to particulates containing metals and metal fumes (PCMMF) is a potential concern in ore refining and smelting. Some metals of primary interest are arsenic, cadmium, copper and lead, which have been linked to various adverse health effects. The current National Institute for Occupational Safety and Health (NIOSH) sampling method for metals in particulates requires the use of a filter, precision airflow pump and laboratory analysis. A major concern with this method is the one-to-two weeks? wait before laboratory results are available for use in determining if additional controls are needed to assure adequate exposure protection for workers. Particulates containing these metals were sampled during sixteen sampling events at a copper smelter using the traditional NIOSH methods. Monitoring of particulates was simultaneously conducted using a TSI 8520 Dust-Trak real-time aerosol monitor with a 10-µm-cutpoint sampling inlet. NIOSH analytical methods related to particulates and metals (methods 0500, 0600 and 7300) were used to determine particulate mass and individual mass contributions of metals on sample filters. Linear regressions with y-intercepts forced to zero were developed to determine the relationship between the PM10 measurements recorded by the DustTrak and laboratory-reported total particulate mass, PM10 and respirable arsenic, cadmium, copper and lead concentrations. These linear regressions yielded correction factors that can be applied to DustTrak readings to obtain total particulate mass, PM10 and respirable concentration estimates for each of the four metals. The R2 (coefficient of determination) values from the linear regressions ranged from 0.65 for total lead to 0.91 for total copper. These results suggest that the DustTrak may produce real-time data useful in providing estimates for airborne concentrations of arsenic, cadmium, copper and lead in copper smelter particulates.

Jan 1, 2011

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By Matthew A. Omofoma, Andrew P. Hampton

The application of the Cyprus Cyanisorb process was investigated using a pilot scale facility at the NERCO DeLamar Silver Mine (DSM) in Owyhee County, Idaho. The purpose of this process is to remove cyanide from the DeLamar mill tailings slurry prior to its introduction to the tailings impoundment. This will maintain the tailings impoundment solution in a detoxified condition and thus prevent migratory bird mortalities. The cyanide removed is to be collected and recycled to the mill. The process successfully recovered approximately 90 percent of the weak acid dissociable cyanide (WAD), reducing the effluent tailings cyanide concentration from about 300 ppm to less than 20 ppm. This was accomplished by stripping the slurry with air in a packed tower and recovering the volatilized HCN in a packed absorption tower. Data were obtained for the design of the full scale facility including the stripping and absorption towers, currently under construction at the DeLamar Mine site. Finally, test results indicated that the final pH of reneutralization can be optimized to provide for minimal gold and silver losses, while selectively precipitating unwanted metal impurities (Zinc, Selenium, Iron, and Copper) from solution

Jan 1, 1992

Over the past few years, the School of Mines of Paris has carried out a program of research* on the grade-tonnage relationships in the border zones of porphyry copper deposits. The initial problem was quite difficult : how does the grade vary at the border of the known orebodies? Does it decrease regularly, or do some thresholds exist, where the grade diminishes abruptly? The answer to these questions have important repercussions on the prediction of the future reserves in the fringe of the orebodies. If the grade decreases regularly, very important reserves could exist; if not, there would be strong limitations to the possible recoverable reserves. The first step of our study was a critical study of previous work done on the subject. It appeared that, following Lasky's pioneering paper (Lasky, 1950), most of the authors used what we can call an historical approach to the problem. In this, the grade-tonnage relationships are calculated from the available figures for production and reserves and the results are then extrapolated to the future. The strong limitation of this model are brought out in this article.

Jan 1, 1982

By Matthias Neuenschwander, Andreas Theiler, Patrick Steinle, John Singer, Martin Vogel, Diego Martini, Ömer Ündül, Markus Weh

"Quartz Dust is a major health hazard in underground works, wherever the ground contains quartz and depending on the chosen method of excavation. A research project initiated by the Swiss Tunnelling Society and realized by the Swiss Federal Institut of Technology, Zurich, established a correlation between the potential of quartz dust generation during excavation and well known geotechnical characteristics – the Cerchar Abrasivity Index CAI and the Uniaxial Compressive Strength UCS - of ten typical Swiss rocks. The results are at the center of a new guideline by the Swiss Society of Engineers and Architects on the requirements for early project stages regarding ventilation and logistics in function of the quartz dust related risk of the expected ground type of the project. The approach presented could be applied worldwide, contributing to more effective health protection as well as to better cost stability in underground works. CONTEXT Respirable quartz dust (aerodynamic diameter of particles < 10 micron) is universally recognized as a major workplace health hazard. Chronic bronchitis, silicosis and lung cancer can be caused by excessive exposure to quartz dust, as has been proved by many medical studies. Therefore, the legislations of many nations specify a maximum workplace concentration (Maximale Arbeitsplatzkonzentration MAK, Occupational Exposure Level OEL). In Switzerland, for example, the Threshold Limit Value TLV for respirable Quartz or Crystalline Silica imposed by the Federal Committee on Exposure Levels (Grenzwertkommission) is 0.15mg/m3 air. Some nations refrain from establishing a OEL because of the carcinogenic nature of quartz."

Jan 1, 2016

By P. Berendsen

The tectonic and sedimentary environment of the Central North American Rift System (CNARS) provides all excellent setting for major mineral deposits. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending transcurrent fault systems may exercise control over ore forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu. Ni, Co, Ti, Au. Ag and PG-minerals are known to occur in this setting. Arkosic sandstone, siltstone, shale, and minor carbonate units occur on top of the rift basalts and in flunking basins where they may reach thicknesses of 10 km (6 miles). The potential, for stratiform or unconformity-related metalliferous deposits must be considered. The rift as a whole remains, however, largely unexplored.

Jan 1, 1990

By C. J. Weiss

"A commercially available Through-the-Earth (TTE) communications system was evaluated at an underground coal mine in eastern Kentucky. This field study was conducted as part of a larger multi-site evaluation of available TTE systems to determine their operational sensitivity. Field testing is being performed along with simulation techniques developed for geophysical surveys. The results of the field test will additionally be used to determine the applicability of these simulation techniques to TTE communications. The mine detailed in this paper was idled at the time of the study, which provided the nearest practical representation of a post-event mine shutdown. For this study, the three following communication modes were tested: surface-to-underground, underground-to-surface and surface-to-surface. Standard deployments of the TTE system using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations. Other arrangements of the units yielded intriguing results, some of which were predicted by computer simulations, others were unexpected. Future experimentation is planned to further evaluate the observed phenomena. INTRODUCTION The ability to establish effective communication between surface and underground personnel after a mine event is essential for both mine evacuation and mine rescue efforts. Current communication technology is reliant on physical infrastructure, such as antennas, cables, and repeaters, located throughout the mine. Such systems are easily disabled during a mine event because of their vulnerability to physical damage. A true emergency communications system would have the ability to function regardless of a mine’s physical state. Through-the-Earth (TTE) wireless communications technology has the potential to provide such a tool. Wireless TTE communications are exceptionally challenging because electromagnetic (EM), or radio, signals are subject to drastic attenuation as they travel through solid strata. In addition to attenuation, EM wave propagation is directly affected by the physical and petrographic characteristics, mineral compositions, metamorphic properties, and the degree of water infiltrations in the strata [1-5]. These strata characteristics are unique to each mine thus making the design of an effective, universally deployable, and reliable TTE communications system very difficult. At present, TTE technology is in the preliminary stages of practical deployment with only a few permissible TTE systems commercially available."

Jan 1, 2015

By C. Allen, H. Zhang, L. Falk

Shock loss occurs when there is a change in the area of a drift or airflow direction. These shock losses accumulate throughout the ventilation system and will increase the mine resistance as underground development deepens or becomes more complex. Hence, shock losses should be carefully considered when establishing the resistance through a series of branches as they can be a significant contributor to the estimated mine resistance. Using computer software to simulate a ventilation system is common but applying reasonable shock loss factors in the software is not a simple or direct process. Determining shock loss values includes the consideration of historical measurements, application of factors and formulas from literature based on the geometry and complexity of junctions, and the geometry variation at different locations. For example, the shock loss at the bottom of a ventilation raise can consist of a 90° bend and a sudden area change. This paper presents an approach for estimating shock loss factors near raise junctions using computational fluid dynamics (CFD). Current and future work will also be compared with field measurements. Results from this approach are compared with software defaults as well as classical techniques in published literature and standards.

Sep 1, 2024

By Robin P. Gardner

The mechanistic or phenomenological approach to ball milling involving the, concepts of particulate selection and breakage functions with particle population balance models has been well established over the past decade (c.f., the review articles by Austin (1) Herbst and Mika, (2) and Snow (3)). Initial efforts to apply this approach concentrated on batch milling, but since most milling in industrial practice is continuous, much recent research has been directed to extending this approach to continuous milling. The primary difference between batch and continuous milling processes is the relative importance of material mixing and transport in the mill in the latter case. Much analytical (4-8) and some experimental (9-15) work on the effect of mill mixing and transport on milling has been recently reported. Much of the analytical work has naturally centered around extension of the well-developed concepts that have been applied to chemical reactors, (16-18) Fortunately, it has been found(1) that most milling processes are analogous to first-order chemical reactions so that the combined effects of material transport and reaction (breakage) can be handled by the relatively simple segregated flow concepts. (8)

Jan 1, 1973

By Werner A. Dürrfeld

The Bullflex® System was introduced as a substitute for timber and debris lagging in mines and to create an in-situ early-stage interlocking effect between steel supports and the rock wall. As deplacement and/or disintegration of strata and of rock beds is to be avoided under all circumstances - following the ideas of NATM-steel support can only be loaded to the maximum when point load is avoided and ideal bedding of the rock is maintained.

Jan 1, 1981

By Lawrence D. Ramspott

A test of retrievable geologic storage of spent fuel assemblies from an operating commercial nuclear reactor is underway at the Nevada Test Site (NTS) of the U.S. Department of Energy his generic test is located 420 m below the surface in the Climax granitic stock. Eleven canisters of spent fuel approximately 2.5 years out of reactor core (about 1.6 kW/canister thermal output) were emplaced in a storage drift along with 6 electrical simulator canisters. Two adjacent drifts contain electrical heaters, which are operated to simulate within the test array the thermal field of a large repository. Fuel was loaded during April-May 1980 and initial results of the test will be presented.

Jan 1, 1981

By A. M. Galperin

Back analysis is a very important procedure for proper understanding of physical processes. Back analysis can be used to establish the role of different factors, define parameters to be calculated and formulate the behavior of natural or physical processes based on field experimental results. It is evident that, in order to obtain the necessary data for back analysis, field observations are required. For the Michailovsky region (Kursk Magnetic Anomaly, KMA) the long-term strength characteristics of the clay covering the quarry slopes were established with the help of back landslide calculations. The obtained data allowed quantification of the shearing resistance parameters at the presence or absence of intermittent dips of discharge in the pit bank massif structures. Based on the results of investigation for material composition, strength and deformation of finely dispersed (clay-chalk) deposits in the Kursk Magnetic Anomaly including measuring of the settlements of filled structures, complex probing and laboratory determination of water-physical and mechanical properties of "man-made" soils, engineering-geological zoning of filled structures was carried out.

Jan 1, 2005

By J. Edberg

"This article details the use of an alternative testing method to the 2004 "Post-Tensioning Institute (PTI) Recommendations for Prestressed Rock and Soil Anchors" manual’s recommendations for temporary and permanent rock anchors for applications in shafts and tunnels. This method was developed and used for the Black River Tunnel (BRT) project in Lorain, OH as a means to reduce testing time of rock bolts during shaft construction while maintaining a similar level of quality control and assurance. The following sections will detail the project background, subsurface characteristics, shaft construction, the 2004 PTI testing method and associated difficulties, the alternative testing method and conclusions reached.Project backgroundThe city of Lorain is located in north central Ohio on the south shore of Lake Erie, approximately 40 km (25 miles) west of Cleveland and 119 km (74 miles) east of Toledo. The city chose to build a large-diameter storage tunnel and pump station to meet its requirements to reduce sanitary sewer overflows to the nearby Black River. NTH Consultants Ltd. (NTH) was retained by the city’s prime consultant, Malcolm Pirnie Inc. (now the water division of Arcadis), to perform a geotechnical investigation, develop design and construction bid documents for the tunnel and shaft liner systems and ultimately provide oversight assistance during the construction phase of the project.The BRT is an approximately 1,700-m (5,560-ft) long, 7-m (23-ft) diameter rock tunnel to be lined with a 5.8-m (19-ft) inside diameter secondary concrete lining (Fig. 1). The tunnel is designed to accept flow at a new drop shaft (Shaft 3) located on the west side of the Black River, across from the city of Lorain Black River waste water treatment plant (BRWWTP). The tunnel will be dewatered at the south end by a large diameter pump station (Shaft 1) located in the existing Lorain Port Authority Public Boat Launch. Flow from the new pump station will be discharged into an existing shallow interceptor sewer and directed back to the BRWWTP."

Jan 1, 2014

By K. R. Weller, U. J. Sterns

The goal of most in-plant studies is to identify factors that limit overall plant performance. A major finding from such studies is that interactions between unit operations are always important, usually specific for a particular ore and plant combination, and are one of the limits to plant performance. Computer simulation based on process models developed from in-plant studies is a useful tool for identifying limits to performance and for estimating the effects of proposed changes at both pilot and industrial plant scales. Examples involving interactions between comminution and various separation and agglomeration processes are presented, and directions for future development discussed.

Jan 1, 1989

By William J. Shampine

The Floridan aquifer, which underlies all of Florida, yields water with a hardness of less than 180 pmts per million (ppm) in the northwestern part and throughout much of the center of the Slate. In most of the rest of the Stale, the aquifer yields water having a hardness greater than 180 ppm and as much is 1,900 ppm. Hardness of ground water is caused by dissolved salts from the geologic formations through which the water passes or by direct pollution. Sometimes pollution may indirectly increase the hardness of ground water by increasing the acid content and thus increasing the solution of calcium and magnesium salts. Water from deep zones of the aquifer lend to he harder than water from more shallow zones. Only the hardness of water from the upper part of the aquifer is shown.

Jan 1, 1966

By Andy Davis

The evolution of pit lake water quality depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock vs. oxidizable sulfide content, the alkalinity of recharging groundwater and the evapoconcentrative characteristics of the system. This paper assesses the geochemistry of 11 existing pit lakes, ranging from the acid Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits, with long-term chemistry lying on a geochemical continuum between end members that consist of influent calcium bicarbonate groundwater and naturally occurring sulfate-rich evaporate playa lakes.

Jan 1, 1997