Search Documents

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

5.1 TECHNOLOGY FOR INJECTING GROUT INTO BOREHOLES The grouting of fractured rock aquifers is carried out in separate stopes' whose size is determined by the hydro¬stratigraphy and the hydrogeologic properties of the rocks. The number of grouting stopes required depends on the number of intervals in the hydrogeological section. Each grouting stope can include one or several aquifers. Com¬bining several water-producing strata into one stope is pos¬sible only when the values of their permeability coefficients are very similar. In order to achieve efficiency, as many aquifers as possible are included in each stope. In practice, the length of a grouting stope in a borehole usually ranges within 10 to 40 m, but occasionally up to 100 m or more. When conducting grouting operations through boreholes drilled from the face of underground workings, the stope's size can be determined by the thick¬ness of each fractured zone (fault) or by the length of the hole if the entire rock is fractured. Injecting grout into separate intervals of fractured rock can be done from the bottom to the top with ascending stopes or from the top to the bottom with descending stopes. Injection from bottom to top is always preferred. Injection also can be accomplished in separate fractured permeable horizons in the section. The STG integrated grouting method is based on the use of packer and injection equipment and technological schemes that facilitate injection in highly isolated fractured aquifers. For this purpose STG has developed a standard series of packers. 5.1.1 INJECTING GROUT THROUGH BOREHOLES DRILLED FROM THE SURFACE Grout can be injected according to one of four techno¬logical schemes depending on the depth of the fractured aquifers, their hydrogeologic properties and the availability of grout injection equipment if the area is remote (Fig. 43). In the first and most preferred technological scheme (1), the grout is injected from the bottom up with ascending stopes. When this scheme is employed, grouting holes are drilled to the entire projected depth based on the field investigations injection tubes is installed above the top of the first hydrostratigraphic unit to be grouted. This scheme al¬lows the grout to be injected only into the permeable stra¬tum or strata isolated by the packer near the bottom of the hole; it precludes the need to clean or redrill the hole before injecting grout into the next overlying stope. This ascending stope scheme is preferred because of its simplicity and ef¬ficiency. It is used in most of the grouting of saturated fractured rock for the purpose of isolating aquifers while excavating deep mine shafts in the USSR. The second technological scheme (II in Fig. 43) injects the grout in sequence from top to bottom with descending stopes. Injection under this scheme is accomplished through the hermetically-sealed mouth of the hole. It is most advis¬able to grout with descending stopes in saturated fractured rock wherein the aquifers constitute thick networks of frac¬tures. Under these conditions it is practically impossible to drill a grout hole to the entire depth of the underground workings due to the large production rate of ground water. In conducting isolation operations with descending stopes, additional work (relative to ascending stopes) is necessary to drill out the grout in order to create and inject the next stope. As a result, the total amount of drilling required to drill out grout can even exceed the volume of drilling of original rock. Consequently it is advisable to use this inefficient scheme only for injecting grout into holes that contain prolific frac¬tured aquifers at depths less than 150 to 200 m. The third and fourth technological schemes (III and IV in Fig. 43) are used in the selective grouting of separate aquifers. For example, these methods would be applied when a grout hole is drilled to its entire depth, wherein grouting of the upper aquifers must be done first so that the sinking of the first shaft can begin prior to deeper grouting. The third technological scheme is used for the selective injection of grout into an aquifer with a thickness of up to 5 m. For this work the DAU-1-2 removable dual packer is installed. It is lowered into the borehole on an injection pipeline. For aquifers with thicknesses of more then 5 m, the selective injection of the grout is carried out according to the fourth technological scheme; a combination of the DAU-2 hydrodynamic plug and the DAU-1 packing device is used. In order to implement this injection scheme, the DAU-2 hydro-dynamic plug is installed at the bottom of the fractured aquifer and the DAU-1 packer is installed at the top of the aquifer.

Jan 1, 1993

By Rosa H. Harris

The world's largest gold dump leach operation, Minera Yanacocha S.A., has installed community assistance programs in Peru concerned with health, education, electrification, agricultural assistance and road improvements. The programs are conducted in a joint venture fashion in association with various organizations.

Jan 1, 1998

By E. G. dos Santos, M. M. Veras, C. H. Sampaio, A. S. Young, R. S. Paranhos, C. O. Petter, A. C. Bastos

"The major challenges of the current mining are the energetic optimization, the lowest water consumption and minimizing environmental impact. One technique that eliminates much of the waste avoiding milling sterile, operating without water and to decrease the generation of waste at the end of the process, must be considered a major innovation. One of the most important developments in these past 10 years in the mining industry was expanding the use of high-tech sensors aimed at pre-concentration of ore. Among the mining areas where this type of technology is booming is the industrial minerals. The most common sensors are color sensors with Charge – Coupled Devices (CCD cameras) allowing through the RGB colorimetric system, the separation of minerals with different hues, and in many cases, a difference in brightness. More recently, the development of the use of dual energy X-ray transmission (DE-XRT) Dual Zone allowed the separation by atomic density of the mineral constituents of the rock. This paper presents a review of these two techniques (CCD and DE – XRT) as well some results showing the use of these two techniques for Earth Rare and Limestone. INTRODUCTION The mining industry is going through one of its biggest technological changes since the industrial revolution by the implementation of new technologies, according to Australian Mining Magazine (2015), whose theme emphasized one of the 10 greatest challenges that mining will face in the coming years. Optimization of the energy matrix in mining is focused on reducing water consumption and minimizing environmental impacts. The implementation of sensor technologies (Sensor-Based Sorting - SBS) allows elimination of mill tailings and permits the mill to operate with reduced use of water or totally eliminate this consumption (Young et al, 2016). According to Jönsson (2014) mining has undergone striking changes with the expansion of sensors of high technologies applied in the pre-concentration of mining ores. These techniques have contributed over the past 10 years in the recapture of mining areas with emphasis on the environment and/or operational optimizations. In line with the requirements of technological innovation, the mining industry is forced to make improvements in gravimetric processes ensuring better levels of Run of Mine ore feed in beneficiation plants. The implementation of automatic sorting, assisted by dual energy x-ray transmission (DE-XRT) sensor technology, or charged coupled device (CCD) image capture camera technology in the feed plant, allows for the selective sorting of individual particles into pre-concentrations (Veras et al, 2016)."

Jan 1, 2017

By H. -S. Yoon, C. -J. Kim, K. W. Chung

"With the final goal of ultrasonic application to ion exchange in a resin-in-pulp (RIP) system, the feasibility of an indirect ultrasonic application with a submersed ultrasonic probe was investigated first for the enhancement of ion exchange in the following resin-in-solution (RIS) system: Lewatit MonoPlus MP 600XL in an artificial solution with 106 ppm uranium. Ultrasonic radiation enhanced the ion exchange efficiency without mechanical degradation of resin. For 3.6 g/L of resin, the enhancement was 79 percent after 10 min of ion exchange and it gradually decreased to 11 percent at 60 min. In addition, a preliminary test of the mechanical stability of the resin in the RIP system showed little mechanical fracture of the resin due to ultrasound, which indicates that indirect ultrasonic application by a submersed ultrasonic probe is applicable for RIP systems. IntroductionIn uranium ore processing, the ion exchange process has been used on a commercial scale for preconcentration and purification (Gonzalez-Luque and Streat, 1984). The ion exchange process is divided into two processes: (1) a resin-in-column process with the uranium-bearing solutions passed through columns containing resins and (2) a resin-in-pulp (RIP) process with the leached ore pulp exposed to resins. The latter does not require the separation process of leach liquor and ore solids, which reduces process costs. This process, which has been developed commercially since 1955, has a certain drawback. The adsorption rate and efficiency in the RIP process are relatively low, so numerous contacts between resins and leached ore pulp are needed, which adds to the cost (Merritt, 1971). It is necessary to study methods to reduce process costs.Ultrasound can intensify mass transfer, increase the rate of chemical reactions, and change reaction pathways (Thompson and Doraiswamy, 1999; Luque de Castro and Priego-Capotem, 2007; Adewuyi, 2001; Luque-Garcia and Luque de Castro, 2003). It has great potential in chemistry and is especially considered to be a promising method for enhancing mass-transfer-limited processes, such as ion exchange. Enterzari and Tahmasbi (2009) reported the effect of ultrasound on water softening by ion exchange. Band et al. (1997) proposed a modulated ultrasound application to water desalination with ion-exchange hollow fibers. These reports revealed that ion exchange kinetics could be enhanced by the application of ultrasound. As for hydrometallurgy, Feng and Aldrich (2000) reported that the elution of an ion exchange resin was enhanced by the use of ultrasonication."

Jan 1, 2015

By John K. (Original by) Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 32.7 t (36 st) of water for each ton of coal produced, while bituminous mines average about 4.5 or 5.4 t (5 or 6 st). Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a mine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed of is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. It must be controlled long before it reaches this stage. Water standing in the working faces is unpleasant for the men who have to work there and also cuts down on the amount of work they can do, as they must watch where they step all the time. It is especially unpleasant in low coal.

Jan 1, 1981

By A. Wahab Khair, Negendra P. Reddy

INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982). One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Elorgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cy to toxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le ?oux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly . Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles , of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield,

Jan 1, 1986

By Susanne Pignolet-Brandom

Flash smelting products of a copper sulfide concentrate collected at successive levels in an experimental reactor have been studied by reflected light microscopy, scanning electron microscope - energy dispersive analysis and electron nicroprobe analysis. Chalcopyrite, intermediate solid solution, bornite, chalcocite, metallic copper, magnetite, iron-copper spinel, pyrrhotite, hematite, delafossite and cuprite have been identified in the product samples. The detailed reflected light microscopy study of these phases and their abundance in the samples has resulted in the identification of the series of reactions during flash smelting.

Jan 1, 1985

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

Polysaccharides have been used as depressants for naturally hydrophobic talc in the flotation of base metal sulfide ores, precious metal sulfide ores and platinum group metal (PGM) sulfide ores. The results of this surface chemistry study confirm guar gum as a preferred polysaccharide for talc depression in the flotation of these ores. In addition to the practical application of the research results, the surface chemistry results are of academic significance, providing further information to understand how polysaccharide depressants function in these complex sulfide flotation systems.

Humic acids adsorb on coal and depress coal floatability in the acidic pH range. In alkaline solutions, their effect is not pronounced. In the neutral pH range, a second small addition of kerosene plus MIBC leads to a significant increase in coal yield and better selectivity. Humic acids present on oxidized coal surface were found to be responsible for the inhibited floatability of the? coal. As expected, the flotation of such oxidized coal also strongly depends on the method of pH adjustment.

Jan 1, 1988

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1988

By Lane White

The nature of the new Mining Law in Mexico, how it works and its implications for foreign investors were discussed from a variety of points of view by speakers participating in SME's special programming on Mining in Mexico at its An¬nual Meeting in Albuquerque, NM Feb. 14-17, 1994. Following are summaries of three papers whose primary objective was to give foreign investors some insight into the nature of doing business under the current Mexican Mining Law and its regulations. Lane White, Publisher.

Jan 1, 1994

By Yehia El-Ibiary, M. P. Evans

One way of increasing conveyor systems productivity is by monitoring the key parameters in the systems. In this paper, a new line of smart bearings will be presented and discussed. The new bearings are capable of monitoring temperature, vibrations, and belt speed for early detection of potentially serious problems. The new smart bearings have built in sensors that are carefully integrated and protected for long life service. These bearings are going to be the key to increasing the up time of belt conveyors in the future.

Jan 1, 1996

By J. D. Pfarr

The Homestake Mine, located in Lead, SD, has been in business for 113 years. Until 10 years ago, conventional mining methods were used to extract ore. Due to complexities in the ore bodies and increasing costs, new technology was introduced to the mine. An integral part of this technology was mechanized cut-and-fill mining. This mining method currently produces about 50% of the annual production and has proven to he safe and economical. As a result, the Homestake Mine remains competitive in today's market.

Jan 1, 1992

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption, and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1987

By Guido Venturini, Giorgio Martinotti, Luca Delle Piane, Paolo Perello

This paper presents a critical review of geo-structural mapping methodologies applied to deep tunneling projects in complex mountain chains such as the Alps. Geological forecastings are often a crucial part of tunneling projects, which should allow contractees or contractors to assume their own risks. Despite this, often adequate methodological criteria are not applied in the realization of these studies, with consequent increase of costs and delays. A discussion should hopefully start in the world of tunneling in order to define a correct approach.

Jan 1, 2003

By Alexander N. Winchell

"The iron ores of the Lake Superior region are found almost exclusively in rocks of Huronian age, the only exception of importance being in the Vermilion district. It may be estimated that about 95 per cent of the ores thus far mined have been obtained from Huronian rocks. Although these ores come from rocks of varying age and slightly varying type, they have many features in common, and therefore may readily be described together.The iron formations of the Lake Superior region consist essentially of interbanded layers of mixtures in widely varying proportions of silica and iron oxide, and are called taconite, ferruginous chert, or jaspilite. They vary considerably in hard¬ness and color, depending upon the tenor of silica and the history of the rock. Local phases of the iron bearing formation consist of cherty iron carbonates, greenalite or ferrous silicate, rocks, amphibole-magnetite masses, cherts and slates, and pyritic quartz rocks. The average iron content of all the original phases of the iron bearing formations, excluding interbedded slates, is about 25 per cent, while the average iron content for all portions of the formation, whether in the original condition or not, is about 38 per cent. It is believed that this difference is due essen¬tially to the removal of silica in solution from the. primary phases, and, of course, such removal of silica has in many cases produced material now used as iron ore, since it contains con¬siderably more than 38 per cent of iron."

Jan 1, 1920

By Weijian Yu, Jianbiao Bai, Jinlin Xin, Shiqiang Xu, Shuai Yan, Zizheng Zhang, Hai Wu

The retained roadway subjected to dynamic loading from thick and hard roof (THF) fracturing caused severe deformations in the thick coal seam (TCS). Understanding the dynamic loading mechanism of gob-side entry retaining (GER) in TCS with THF is the first step in determining the stability of the retained roadway. Characteristics of dynamic loading mechanism of gob-side entry retaining (GER) in TCS with THF are investigated through numerical simulation and field test of 150208 haulage gate in Sucun coal mine. To improve the reliability of numerical simulation, the double-yield model is used to simulate gob and the strain-softening model is used to simulate filling body; the dynamic module in FLAC3D is used to simulate the dynamic loading due to the THF fracture, and the global model are validated. Characteristics of surrounding rock convergence, plastic zone distribution, and vertical stress in the filling body after the THF fracture are reveled with respect to width to height ratio (W/H) of the filling body and the dynamic loading strength of the THF. The rational width to height ration of the filling body constructed with high-water materials is 0.57. Field monitoring results show that the GER with THF in Sucun coal mine could adapt the dynamic loading due to the THF fracture and meet the requirement. This study is helpful to better study the stability of GER according to the breaking dynamic load of THF and provides reference and guidance for the analysis of breaking dynamic load of THF under similar geological conditions.

Feb 23, 2023

By Shaojun Bai

Siderite ore with high phosphorus content was reduced isothermally at 1,050° C with pulverized coal and different dosages of sodium carbonate. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energydispersive analysis of X-rays (EDAX) were used to characterize the samples. The influence of sodium carbonate on the carbothermic reduction process was investigated. Sodium carbonate and its dosage played a considerable role in the carbothermic reduction. The iron particle size in the reduced ore was below 20 µm, and fayalite was abundant without sodium carbonate additive. With a mass ratio of Na2CO3-to-ore of 5% additive, the iron particle size in the reduced ore was generally above 50 µm, and the diffraction intensity associated with metallic iron in the XRD pattern increased. The effect of sodium carbonate on the phase transformation of fluorapatite during carbothermic reduction was also addressed via thermodynamic calculations and aqueous leaching experiments. The results showed that the fluorapatite was not reduced to P2 at 1,050° C, and a portion of the fluorapatite was converted to soluble phosphate. The reduction of siderite can be catalyzed by adding an appropriate amount of sodium carbonate. This catalytic activity was caused by an increase in the reducing reaction activity of FeO and the acceleration of the carbon gasification reactions. The decrease in phosphorous content in the iron concentrate was attributed to an improvement in the separation of the iron phase from the slag phase when sodium carbonate was added and with the formation of soluble phosphate.

By Paul Dean Proctor

The world's population by 2000 A. D. may approximate 6.5 billion and the United States' 304 million. South Asian population increases between 1970 and 2000 A. D. will be triple the projected population of North America. Such anticipated dramatic and probably traumatic increases in world population yield grave concern for the standard of living in the world and the United States. The people of the United States currently consume 32 percent of the world's energy and similarly large percentages of the world's mineral raw materials. With only 6 percent of the present world's population and slightly smaller percentage by 2000 A. D., much expanded world-wide production of energy and raw materials will be required to maintain even a standstill living standard. A minimal 2 percent increase per year in the standard of living in the United States and a 4 percent increase elsewhere in the world, beyond the demands of the estimated population increases, suggest the magnitude of the increased need for energy-mineral raw materials and the possible crises the world will face in these areas by 2000 A. D. Mineral engineers and scientists with broad educational backgrounds will be required in greatly increased numbers to help alleviate, and possibly avert, expected energy-mineral raw materials shortages of the next millenium. Explorationists, mineral engineers, commodity economists, environmentalists, city, county, state, and federal mineral materials planners and coordinators, and metallurgists will be among those most needed. AIME membership in the second century of the Institute's history will contribute directly to this personnel pool.

Jan 1, 1971

By Paul A. Rittenhouse

Its a pleasure to be with you this afternoon and to talk briefly on one of my favorite subjects -- the U.S. sulphur industry. As our Chairman mentioned, I have been associated with the sulphur industry either directly or indirectly for the last twenty years, both on the production side and as a consumer. Sulphur, while unseen and relatively unknown to most people, is like margarine ... that ubiquitous spread ... that is yellow and nearly omnipresent in the industrial world. It is because sulphur, in some form, is required in nearly all aspects of our economy that makes its study so interesting to me as a researcher. An analysis of the sulphur outlook requires examination of such industries as fertilizer, paints and pigments, copper and zinc, uranium, petroleum, chemicals, pulp and paper and textiles - just to name a few. Of course, because its use is so widespread and ever-changing it is difficult to develop and maintain a good understanding of the sulphur industry. It is also a problem to cover the industry in a short discussion and to project its really dynamic nature. Hut, if you will bear with me, I will attempt the task. First of all, let me say that sulphur today is a world commodity and to a large extent moves freely in world trade; nearly a third of the world's sulphur or something over 15 million tons in 1974 entered international trade. However, today our interest is in the current changing sulphur picture in the U.S., with particular emphasis on the western part of the country.

Jan 1, 1975