Search Documents

By Yoginder P. Chugh

About 65% of the U.S. coal production (835 n tons was surface mined. A similar proportion of the Illinois basin's production (112 m tons) is also surface mined. The state of Illinois is the third largest producer of surface mined coal in the United States, after Wyoming and Kentucky. The Illinois coal basin encompasses Illinois, southwestern Indiana, and western Kentucky, as shown in Figure 1 (dotted lines). The estimated surface mineable coal resources in the basin amount to about 27 billion tons, and about 69 m. tons of coal is surface mined annually (Tab1e I).

Jan 1, 1981

By R. B. Tippin

The material balance computer program (MAT-BAL) developed at the Minerals Resource Research Center of the University of Minnesota, has been used in conjunction with routine process profile samples taken in the potash compaction plant at Great Salt Lake Minerals and Chemicals Corporation, Ogden, Utah. In this manner, a uniform data base is being established for the process, and selected key indicators are used for decisions in plant operation and maintenance. With present emphasis on improving product quality and increasing production rates, the standard data base system provides a means of measuring results from test programs to optimize the circuit. The development and application of this process control method is discussed. The compaction plant computer-assisted data base has been in existence for only two years, but it has made significant contributions to the knowledge of the process and continues to assist in monitoring the plant performance. It is anticipated that the material balance program will be adapted to the GSL flotation plant in 1979, and to other circuits in the potassium sulfate chemical plant.

Jan 1, 1979

By R. A. Franks

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system?s ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system?s ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2008

By Yuexin Han, Yanjun Li, Peng Gao, Yongsheng Sun, Qiang Zhang

The non-isothermal magnetization roasting process and isothermal magnetization roasting process of siderite ore were investigated using thermogravimetric (TG) analysis and a real-time infrared gas analyzer. X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) were used to analyze the characteristics of samples. The results showed that the decomposition degree and decomposition rate of siderite ore were vitally affected by heating rate and roasting temperature. It was determined that A1 reaction model (f(α) = 1 − α) and A3/2 reaction model (f(α) = (3/2)(1 − α)[−ln(1 − α)]1/2) were the most probable mechanism function of the non-isothermal decomposition process and isothermal decomposition process, respectively. The phase transformation and decomposition mechanism during the roasting process were evaluated. Siderite decomposed in the process of magnetization roasting, released CO and CO2, and transformed into strongly magnetic magnetite. The SEM images highlighted that as the decomposition progressed, the structure of roasted samples was destroyed, and an increasing number of cracks and pores emerged on the surface, which is advantageous to the following grinding process.

Mar 26, 2021

By A. Griffiths

The? use of hydrogen peroxide to detoxify gold mill waste waters containing cyanide and other toxic substances is already an established technology. Recent advances have extended the range of application of hydrogen peroxide treatment to include the removal of complex iron cyanides, the simultaneous removal of cyanide and toxic metals down to very low levels and treatment of barren bleeds, CIP' pulps and tailings pond discharges. Three treatment plants are described here. Each was installed at a gold mine in North America in 1987 and each illustrates a different application of hydrogen peroxide. The need for individual design of the detoxification plant to fit particular requirements is shown by the examples chosen.

Jan 1, 1988

By Matthew E. Eisenmann, Gerald H. Luttrell

Performance data from phosphate plants are often untrustworthy because of difficulties associated with highly variable feeds and unstable equipment operation. In some cases, this problem is further compounded by improper sampling procedures and unreliable laboratory analyses. Questionable data often lead to misleading conclusions that result in lost productivity and profits. Data reliability may be checked using mass balances, but the mathematics associated with this procedure can be overwhelming when multiple data sets or complex circuits are evaluated. To overcome this problem, a simple spreadsheet-based mass balance program has been developed specifically for plant operators. To use this program, operators simply enter a description of their circuit and input the assay values (e.g., % BPL, % Insol, etc.) for each stream. The program then generates the best estimates of the assay values and flags values that may be unreliable. The spreadsheet is specifically designed to be easy to use and requires no knowledge of statistics or programming. This manuscript reviews the mass balance problem and describes how spreadsheet programs can be used to evaluate plant data. An example problem involving the analysis of data around a two-stage phosphate flotation circuit is presented.

Jan 1, 2002

By Y. H. Alghamdi, A. D. S. Gillies

"INTRODUCTION Background Diesel Particulate Matter (DPM) has been a critical issue during the last decade in underground mines. This problem is threatening the health of mine workers, as well as the mine’s productivity. It has been confirmed that the diesel engine exhaust is the main source for the diesel particulate matter (DPM), and that it has the highest impact in raising carbon monoxide, carbon dioxide, oxide of nitrogen, and hydrocarbons in the underground environment. Miners who are exposed to this kind of emission are at high risk for developing lung cancer and other lung diseases. The Mine Safety and Health Administration (MSHA) has issued standard rules to regulate diesel emissions in underground mines. The final ruling confirmed in 2008 that the total carbon should not exceed 160 µg/m3. (MISHA, 2008) Monitoring DPM in underground mines has become important to ensure compliance with the MSHA regulations. There are many different types of DPM monitoring systems that are currently being used in underground mines. Two methods are typically used for DPM sampling: the personal sampling method or the direct exhaust sampling method, which takes a direct sample from the engine’s tailpipe. Many mines do not recommend using the direct exhaust sampling method since it involves complex measuring equipment and procedures, as well as it is not regulated in the United States or Canada. Thus, the personal sampling method is the preferred method in many mines when taking DPM samples. Even this method includes many variations, such as the Respirable Combustible Dust (RCD) method and the method devolved by the National Institute for Occupational Health and Safety NIOSH 5040. The NIOSH 5040 method is the preferred method overall because it gives more accurate measurements compared to the other methods. This method does not allow organic carbon sources other than those coming from diesel engine exhausts to interfere with the measurements, which otherwise would lead to overestimating the actual amount of the DPM in the mine environment. An impactor feature in the cassette, which holds the samples in the instrument, characterizes this method. Since the diesel particles are less than 0.9 micron, this impactor does not allow particles more than 0.9 microns to be collected in the cassette filter. The cassette is then analyzed in a lab and the concentrations of organic carbon (OC), elemental carbon (EC), and total carbon (TC) are determined. Lately, the National Institute for Occupational Safety and Health (NIOSH) has developed a new instrument that can use the same concept of NIOSH 5040, but with instant measurements of elemental carbon. It utilizes laser radiation with the cassette so it can give a real time measurement. The real time measurements give instant information about the underground environment that will allow the mining engineer to take immediate action and enact plans instead of waiting for results from the laboratories where NIOSH 5040 method may take several weeks to get the measurements."

Jan 1, 2016

By Emily Sarver

"Across all sectors and commodities, a common theme is driving progress in raw resource supply: sustainable development (SD). Over the past few decades, the mining and minerals industries for their part have undertaken significant and intentional changes at every level to become more responsible — no longer to just their shareholders, but also to the environment, to the communities in which they operate and to society at-large. Led by some of the global majors, these industries have indeed helped to define and operationalize the basic principles of sustainable development. Now in the midst of a full-on cultural shift, they are also key players in the continual effort to re-examine and calibrate practices to meet dynamic and increasingly complex objectives.SME’s technical position statementAs a home for so many technical experts and practitioners, SME has long recognized the importance of a commitment to sustainable development by the mining and minerals industries. In April 2016, the Society formally adopted a technical position on the topic following years of participation in, and support for, related activities. The full position statement appears below. It was drafted, revised and presented for approval to the board of directors by SME’s Sustainable Development Committee.Statement of Technical Position on The Mining Industry and Sustainable Development:• The National Environmental Policy Act of 1969 (NEPA) and the Surface Mining Control and Reclamation Act of 1977 (SMCRA) imposed considerable environmental restrictions on the mining industry; SME has always reinforced strict adherence to the laws.• In 2002, SME established a Sustainable Development Committee to lead its efforts in this area and to propel the organization into global prominence.• SME is a signatory to the Milos Statement of 2003 on Sustainable Development, so it is committed to providing scientific, technical, educational, and research skills in minerals, metals and fuels.• SME recognizes that SD programs adopted by the industry have a tangible return on investment through brand recognition and loyalty, facilitation of permitting, reduced occurrence of community protests and vandalism and diminished political risks.• SME actively promotes educational programs that encourage professional growth and interaction with the engineering professional community through books, articles, symposia, short courses and/or conferences on sustainable development in the mining and minerals industries.• SME has developed abundant expertise to provide balanced advice to government bodies, congressional staff and other interested organizations."

Jan 12, 2017

By J. B. Hiskey

Introduction The domestic copper industry has suffered for some time from declining ore grades; rising costs associated with conventional mining, milling, smelting and refining; tightening environmental restrictions; and shrinking markets due to materials substitution. Ore grade depletion is a major problem. It is illustrated by the decline in average copper yield shown in Fig. 1. From 1979, copper grade has dropped 60%, lowering yields from 1.2% to 0.49% (Sousa, 1981). The US copper industry is taking drastic measures to enhance its competitive posture and to guarantee its future worldwide position. In a sense, this involves a general restructuring of the processing philosophy of US copper producers. Judging from recent trends, this restructuring relates to the application of solution mining techniques to the treatment of copper ores and low grade waste material. Recovering copper by leaching techniques has been practiced for centuries. As early as the mid-16th century, some Hungarian copper mines were recycling copper bearing leach solutions through waste heaps (Nash, 1912). In the US, recovering copper from dilute mine waters has been carried out for more than 100 years. There are, however, certain technical innovations that have elevated the importance of solution mining as a process for copper recovery. These include: • Advances in solvent extract-electrowinning (SX-EW); • Developments in acid and acid ferric cure processes for oxide and mixed oxide sulfide ores; • Improvements in heap and dump construction; and • Advances in in situ leaching technology. Generally, solution mining enjoys certain intrinsic advantages over conventional mining and milling. Compared to conventional milling, the combined capital and operating costs of leaching facilities are normally lower, start-up times are faster, and the leaching operation usually has less impact on the environment. Furthermore, solution mining represents an expedient way of extracting metals from small shallow deposits, and is particularly suited to the treatment of low grade sources. And, in the case of waste dump leaching, there is a tremendous resource in-place that has the mining cost already off the books. This paper updates current US copper solution mining trends. Solution mining systems Schlitt (1980) summarized the characteristics of the principle leach systems in the US. He pointed out that the wide variations in copper deposits make solution mining a more site-specific activity than conventional mining and milling. Heap leaching is usually selected for moderate to high grade ores having a copper mineralization that is amenable to acid leaching (oxides, silicates and certain sulfides). Higher grade ores mined specifically for heap leaching are usually treated to optimize copper extraction, therefore, crushing and some pretreatment (acid curing) may be justified. On the other hand, dump leaching practice usually involves leaching low grade waste rock placed on large dumps as dictated by topography and haulage costs. Mine waste is therefore treated in an uncrushed run-of-mine condition. Finally, in situ leaching is appropriate for either very deep ore bodies or for recovering copper from low grade rock left behind in abandoned pit walls, stopes, and subsidence zones from earlier mining activities. True in-situ solution mining should be defined as the leaching of ore in its original geologic setting. Heap leaching Heap leaching has a long history as a hydrometallurgical process for copper recovery. The methodology of heap leaching established at Rio Tinto in Spain more than 300 years ago is basically the same as that used today. Processing concepts, such as solution management (sprinklers and leach/rest cycles) and copper

Jan 11, 1986

By R. S. Kasper

This paper reviews the procedure used to quantify the conveyor frictional resistance on a 3.9 km (2.4 mile) long overland conveyor belt. Field torque measurements of the three drives were used to help fine tune a computer simulation of the conveyor. This enabled the prediction of the effect on various conveyor components that cold temperatures will have on increasing the throughput tonnage.

Jan 1, 1995

By R. Xiong, A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, J. Gu

"INTRODUCTION The Central District of the Florida phosphate industry is located in southwest Polk and southeast Hillsborough Counties, with the Southern Extension lying in western Hardee, eastern Manatee and northwest De Soto Counties. (Lawver, 1983) Figure 1 shows the major phosphate formations in Florida. Almost all Florida phosphate production has been in the Central district with additional production from a mine in the Northern District. The Central District is comprised of the Bone Valley Deposit, a relatively thin layer of high grade ore which has been the main source of phosphate mining for decades, and the Hawthorn formation, a thick but low grade formation which covers most of peninsular Florida. (Lawver, 1983) Florida phosphate producers use the Crago process where calcium phosphate is floated with anionic, fatty acid type collectors followed by cationic reverse flotation of silica with amine type collectors. The phosphate matrix is put through various size separation techniques to obtain a typical -28 Mesh (< 700 µm) particle size for fine flotation and a -16 mesh (< 1190 µm) to +28 mesh (> 700 µm) particle size for coarse flotation. In some cases this coarse fraction can be sent to shipping as an intermediate product. The +16 mesh (>1190 µm) to – ¾“ (19 mm) fraction is sent to shipping as a final product called pebble. Figure 2 demonstrates a simplified diagram of the mining and processing of calcium phosphate (matrix) through a Central Florida mine. Particle size and mineralogy are important considerations in the Crago process for two main reasons, the mass of the particle and the particle surface area. Both of which are dependent on the coordination of the anionic collector to available Ca2+ sites on the minerals’ surface. The increased surface area, and available Ca2+, of the smaller apatite particles will allow for more fatty acid molecules to coordinate than the larger particles, with a lower availability of Ca2+. So, the larger particle would require more collector to be introduced in the system to sufficiently cover the apatite particles to produce a surface sufficiently hydrophobic to attach to air bubbles allowing flotation to occur. (Guan, 2009) The Bone Valley deposit has very favorable flotation characteristics when compared to other mining ores around the world. The matrix of the Bone Valley is relatively high grade, BPL (Bone Phosphate in Lime) values typically range from 6-18%, BPL recoveries, from such a matrix, can often be achieved above 85+% with fatty acid based collectors dosed below 1 #/ton. As mentioned, the sizing is an important step as there is also high grade apatite in the +16 mesh (1mm) that is screened to a final product grade, 60-65% BPL. The lack of quartz in the larger size fraction has allowed the Central District to produce high quality, low cost phosphate product, called pebble, through effective screening with no further beneficiation. (Guan, 2009)"

Jan 1, 2015

By O. J. C. Runnalls

Canada has played a significant role in the international uranium industry for some three decades. Although there have been many challenges in the past, the future offers a more extensive range of problems and prospects as Canada moves to expand its activities in all aspects of the nuclear fuel cycle. World uranium demand could grow to an annual requirement of 500,000 tons U308 by the year 2000. A substantial fraction of this material is likely to come from Canada because the country&apos;s reserves and resources are large, and because of a favourable geological potential for future discoveries. There has been a long history of association between the producing industry and the federal government, and it has provided the foundation for existing national uranium policies. Close industry-government association will be maintained and developed in future because of the anticipated rapid growth of the industry and the consequent need for continual refinement of government policies relating to exploration, mining, processing and export of uranium.

Jan 1, 1975

By T. Rockley, B. Goertz, S. McDaniel, J. Brune, K. Bakhsh

"Researchers at the Colorado School of Mines, under a project funded by the Alpha Foundation, have developed a working prototype of a dust sample collection device designed to determine if sufficient rock dust has been placed in an underground coal mine to prevent coal dust explosions. When used in conjunction with the Coal Dust Explosibility Meter (CDEM), the device will provide near instantaneous results on the quality of rock dusting at the tested location. The sampling device applies a pulse of air to a testing surface and collect a representative sample of mine dust based on the pneumatic entrainment process during a mine explosion. The use of both physical testing and Computational Fluid Dynamics (CFD) modeling has allowed researchers to refine the design to accurately represent the particle entrainment and optimize the sample size collected for the CDEM. The prototype is being tested in a mine environment to produce information of usability and practical aspects of mine dust sampling. This paper is a progress report summarizing the current status of sampler development. Researchers expect to have a fully developed and tested sampler in early 2016. INTRODUCTION Underground coal mines face the danger of methane and coal dust explosions. The disaster at Upper Big Branch mine (2010) has demonstrated the impact of a violent coal dust explosion that fatally injured 29 miners. Reviewing the history of coal dust explosions, researchers found that that mine operators and mine inspectors do not have a reliable method of collecting dust samples to assure that sufficient amounts of rock dust have been places to inertize the coal dust. This is a problem specifically with small mines that do not have dedicated safety departments to track rock dusting work. The aim of this research is to develop a simple, portable device that can help underground mine examiners collect dust samples from workings and test the explosibility of the sample near instantaneously. Researchers determined that the current brush-and-pan sampling method required by MSHA (MSHA 2013) is flawed in several aspects: Mechanical sampling with a brush exerts forces on the mine dust that may differ significantly from those present during an explosion. Also, U.S Bureau of Mines research (Nagy 1965) has determined that only the top 0.125 inches of the mine dust layer will be entrained in a coal dust explosion. Using a handheld pan and brush, it is difficult to correctly and repeatably sample a layer of this exact thickness. The following will describe the CFD modeling and experimental testing for the development of the prototype sampler. Researchers analyze the accuracy and performance of the prototype during the course of the build process."

Jan 1, 2015

By Terrence J. Stobbe

On the job injuries to the musculoskeletal system are probably the oldest of the industrial safety problems. Long before we had pinchpoints to guard, chemical vapors to ventilate, and noise to enclose, people were getting strains, sprains, and sore backs from their work activities. In spite of the age of the problem, it remains a long way from being solved. The past ten years have seen a significant commitment by the sci¬entific community to understanding the problem. Engineers, scientists, doctors, and epidemi¬ologists have been involved, and as a result, today we have a much better understanding of the problem. The first step in understanding a problem such as this is to explore its history and epidemiology. The research done by Chaffin (1977), Snook (1970), Ayoub (1978), the ILO (1962), and others, led NIOSH to publish its Work Practices Guide for Manual Lifting in 1981. The guide was based on research carried out in general industry, but subsequent research by Stobbe (1983) and Peters (1983) has suggested that the nature of the problems producing injuries in underground mining is the same as in general industry. The problems are more intense in the mining environment.

Jan 1, 1984

By Enrique Fernandez

M-30, Madrid’s inner ring, covers 42 sq km of the city centre where one million people reside. It was constructed in several phases during the sixties and the eighties. The design criteria applied to those phases were different and were not always homogeneous with urban roads with lighting regulation as well as speedways. These areas had a heavy concentration of access and exits and there had been made many changes on the number of traffic lanes which has caused heavy traffic congestions and high accident rates. The environmental impact and noise pollution in residential areas are also consequences of M-30. The Madrid Major took a decision at the beginning of the present legislation, based on socio economic and environmental evaluation; rebuild the M-30 with the following sustainable mobility principles: Underground transfer of a considerable portion of the main ring and some of its links replacing some parts of the surface with new green areas in order to reduce the environmental impact. Increase the traffic capacity, improving the traffic continuity and fluidity and eliminating the lighting regulation areas, which is one of the main congestion problems currently. Increase the traffic safety with clear signalling information panels and avoiding difficult maneuvering. Redesign the links with the high capacity radial highways and other connecting lanes of the city. The project is worth 3.7 billion Euros. In 2007, when the construction is completed, it is expected will save 14 million of journey hours that represent 4.5 million Euros saved in fuel consumption per annum, There will be a very significant reduction of 35,000 tons of CO2 in terms of pollution and 400 less car accidents. Those values will increase even more in the following years. The areas beside Manzanares River, running parallel to the M-30 on the western side of Madrid, will be highly enhanced. Better water quality and the recovering of the green areas existing in old times will also return for the citizen’s enjoyment. TUNNEL CROSS SECTION OF CALLE 30 SOUTH BY PASS One of the major challenges of the new Calle 30 is actually not only the related to the main road but also to the link with the A-3, with highway to Valencia. This link is currently the most congested area and has one of the highest traffic densities of Spanish roads, with more than 250,000 vehicles/day. The remodelling of this area is the principle objective of the South by-pass. The tunnel is the only answer for this by-pass as the road alignment will go among buildings. A twin tube design, one for each direction, with three lanes allowing the circulation of both, light cars and heavy trucks, is the solution that has been

Jan 1, 2007

By Rambabu Pothina, MELO EDUARDO PIMENTA DE, Rajive Ganguli

 The mining industry is home to a mass of sensor-generated data that are critical to real-time and long-term optimization. This heavy reliance on sensor data has resulted in an undesirable development. The industry is reluctant to verify the accuracy of sensors as it would mean shutting down important processes. Sensors are typically calibrated once a year, if at all. Errors in sensors go undetected until the next calibration or until errors are so gross as to be obvious

By John E. Pavlick

The availability of concentrated brines rich iodide, bromide, chloride, sodium, magnesium and calcium ions has led to extensive chemical manufacturing operations in Michigan. The brines, ranging 1,000 to 8,000 feet below the earth&apos;s surface, are the remnants of ancient oceans which periodically covered and receded over the land area which is now Michigan. After pumping the brine to the surface, iodine and bromine are extracted via an oxidative process. Iodine and bromine find application in catalysts, disinfectants, flame retardants, oil field fluids, film, and gasoline additives. Addition of alkalinity to the brine precipitates magnesium hydroxide, used in high quality refractories needed for steel manufacture. The brines are also the country&apos;s primary source of calcium chloride, employed in ice and dust control.

Jan 1, 1984

By D. S. Flett

Abstract. The commercial importance of hydroxyoximes as extractants for copper has given impetus to basic studies on the chemistry of metal extraction by these compounds. The discovery of accelerator compounds which produce catalytic effects on hydroxyoxime extraction rates has led to mechanistic studies of these rate processes. While these studies have highlighted the importance of interfacial chemical reactions in the extraction process, it is not yet possible to unambiguously describe the mechanisms of metal extraction in these systems or the associated catalytic effects. This paper reviews progress in understanding the mechanism of metal extraction by hydroxyoximes.

Jan 1, 1979

By Paul D. Tomlingson

Modern production equipment has been designed with greater productive capacity and higher reliability to meet the rigorous operating demands of the mining industry. These improvements have also made the equipment more complex and challenging to maintain. Whether these equipment enhancements contribute to more effective mining operations depends on the overall quality of maintenance. Maintenance is not a stand-alone activity. Although its quality depends primarily on maintenance, cooperation and support from other departments, coupled with the skillful guidance of mining managers, greatly influence maintenance success. Therefore, maintenance risk management must look beyond maintenance itself. Successful maintenance risk management begins with an assessment of the maintenance-related interactions of all mining departments within the mine’s stated operating strategy.

Jan 1, 2005

By Walter Meintrup

On Nov. 4, 1981 the newly installed 1000tph wet-process iron-ore ball mill of A/S Sydvaranger completed its first four months of uninterrupted, successful full-load operation in Kirkenes/Norway. This 6.5m diameter mill is driven by a gearless ring or wrap-around motor of 8100kW at 13.1RPM - a first of a kind in this segment of industry. (Fig. 1) This paper analyses the reasons that have led to the selection of this type of drive over more conventional schemes, lists specific advantages of such large mills, and describes in some detail the installation in Norway. General aspects of possible design variations, and application information for designers and users of such mills conclude the presentation.

Jan 1, 1982