Search Documents

By H. Arima, T. Fujita, W. Yen

The copper catalyzed gold oxidation and reduction mechanisms in ammonium thiosulfate solution were investigated by Eh-pH diagram based on the optimum reagent combination for 60 mass% -75 µm silicate ore at 16g/t Au with the maximum gold extraction of 92% and the minimum ammonium thiosulfate consumption of 23 kg/t-ore for 24 hour’s leaching at ambient temperature. The gold recovery by cementation was nearly 100% by Zn and Al powders at Metal/Au mass ratio of 30, and around 95% by Cu powder at Cu/Au+ mass ratio of 50. In order to oxidize the gold efficiently with the less thiosulfate consumption, the stable region of [Cu(NH3)4]2+ should be as wide as possible in the region, where [Cu(S2O3)2]3- was more stable than [Cu(NH3)2]+. In order to reduce gold from the pregnant solution with the less metal powder’s (Zn, Cu, Al) consumption, the stable region of [Cu(S2O3)2]3- should be wider than [Cu(NH3)2]+ on copper precipitation. Zinc powder may recover gold more efficiently than copper powder with the similar trend on the effect of ammonia, copper and thiosulfate. However, the large amount of copper will be co-precipitated along with gold since the stability of zinc ammine and thiosulfate complexes are higher than that of copper’s. Aluminium may reduce gold efficiently at higher thiosulfate concentration and pH. These results were confirmed and compared with the optimum reagent combination for finer grind sample at 100 mass% -75 µm, which is the optimum ore size for the standard cyanidation at 1.0 g/ l NaCN to obtain about 95% gold extraction. The optimum reagent combination was concluded as 0.5 mol/l NH4OH, 0.0001 mol/l CuSO4*5H2O and 0.05 mol/l (NH4)2S2O3 with the result of 94% gold extraction and 3kg/t-ore of ammonium thiosulfate consumption. Gold and copper stabilities were well agreed with the result of coarser grind ore thermodynamically. The lower reagent combination will reduce gold oxidation power, but significantly minimize the reagent consumption. From this pregnant solution, nearly 100% of gold was successfully recovered by zinc precipitation at Zn/Au+ mass ratio of 30. Aluminium and copper precipitations resulted in less than 40% of gold recovery at Metal/Gold mass ratio of 30. The reagent consumption cost on this lower reagent combination followed by zinc precipitation was $1.6/t-ore, while the cyanidation was $3.1/t-ore. Thiosulfate oxidation mechanism indicated the similarity to Belousov-Zhabotinsky reaction.

Jan 1, 2002

By Kousik Sinha

The advantage of using a clean coal as a feedstock in a direct liquefaction plant is improved performance of the plant by several factors e.g., increased throughput of coal; reduced wear and tear of valves, pipes, and pumps; increased liquid yields, etc. This paper examines the technical feasibility for cleaning Illinois #6 coal as a feedstock to a direct coal liquefaction plant via selective agglomeration using a coal-derived heavy distillate, Wilsonville V-1074 as agglomerant. Effects of addition of Kerosene or coal-derived Naphtha as conditioner, coal particle size, slurry pH, oil to coal ratio, and operating temperature on ash reduction and clean coal weight recovery have been studied. Results show that about 70% of the ash can be removed from this coal and the clean coal weight recovery over 85% can be achieved by using this technique with suitable selection of coal particle size, slurry pH, mixing intensity and oil to coal ratio.

Jan 1, 1991

By George E. Peacock

Campbell Red Lake Mine is situated at Balmertown, in the Red Lake District of Northwestern Ontario, Canada. This area is some 120 miles north of the Trans Canada Highway and is some 160 miles Northeast of Winnipeg, Manitoba. The majority of our 300 employees live in Balmertown, which is a community of some 1,200 people, situated adjacent to the mine proper. The mine is serviced by a single shaft 4,300 feet deep. There are 27 levels at 150 ft. intervals. Stoping is being carried out down to the 20th level with only preliminary development having been done on the bottom 6 levels. The majority of our mill feed of 825 tons per calendar day comes from above the 10th level. Gold occurs as specks and streaks in bluish-grey to white quartz carbonate veins. It is extremely fine grained and most is invisible to the unaided eye. In addition to Gold the veins carry varying amounts of sulphides such as, Arsenopyrite, Stibnite, Pyrite, Pyrrhotite and Sphalerite. A minor amount of silver occurs as an impurity in the gold. Arsenopyrite is a marker for the gold ore at Campbell. The average grade of the mill feed is 0.7 oz. of gold per ton. The ore is dumped into an underground ore pass that feeds to a jaw crusher on the 20th level that reduces the rock to a maximum size of 4". This material is hoisted by skips to an ore bin in the head frame.

Jan 1, 1975

By T. L. Myron

In recent years increasing attention has been given to improving both the chemical and physical properties of sinter. The first step toward this goal was the production of a self-fluxing-sinter. More recently, blast-furnace operators have found that significant improvements in blast-furnace performance can be achieved by improving and controlling the physical size of the sinter. The results of full-scale blast-furnace tests have shown that blast-furnace production can be improved by using a closely sized agglomerate. The improvements obtained by the use of pellets, a closely sized agglomerate, are well known. In contrast, blast furnaces charged with sinter having a wide size spectrum have generally not yielded results as satisfactory as those from furnaces 1) * charged with pellets. Beginning in 1958, Appleby-Frodingham charged plus 3/8-inch sinter to their blast furnaces. Further tests by other companies in Canada, 2) the United States, 3) and Australia showed that blast-furnace production could be improved by about one percent when the plus 3/8-inch material in the burden was increased by one percent. Because of the promising results obtained with screened sinter, an extensive test program was initiated to determine an effective means of producing sized sinter in U. S. Steel's sinter plants. This paper describes the work done by the Applied Research Laboratory in this program.

Jan 1, 1965

By Jennifer B. Leinart

With the signing of the North American Free Trade Agreement (NAFTA), Canada, the United States and Mexico entered into an international experiment in economics amid a cloud of controversy that still lingers. Central to the controversy are the disparities in wages that exist among workers in the signing countries. Wage surveys completed by Western Mine Engineering show the degree of disparity that exists among the mining industries of those three countries. Labor costs constitute 30% to 50% of operating costs. So these wage differences are a matter of interest to the mining industry. It is unclear how much of a factor they are in determining where companies search for and develop new mines. That depends on where minable deposits are expected to be found. However, a deposit that may not be minable in the United States or Canada may be minable in Mexico because of lower labor costs. Some adjustments are anticipated for the Mexican mining industry if and when its wages begin to approach comparability with US and Canadian wages. Table 1 combines the results of four recent surveys. It lists benchmark wages for mining job titles common to all the countries. About 220 mines are covered by the combined surveys. Canadian miners' wages, converted to US dollars, are typically 75% to 95% of US wages, while Mexican miners' wages are less than 10% of those in the United States. Table 1 also shows that wage disparities are not confined to international borders. In fact, the difference in average wages between the US coal industry and the US metal and industrial mineral industries is greater than between the Canadian and the US mining industries overall. Table 2 shows that managerial, technical and administrative salaries show similar, but less pronounced differences among the three countries. Salaried personnel at Canadian mines earn 80% to 90% as much as their US counterparts, while those in Mexico earn 20% to 30% as much. Here again, average US coal salaries exceed average salaries for the US metal and industrial mineral industries.

Jan 1, 1998

By S. Stebbins

In 1994 Western Mine Engineering, Inc., (WME), which is now InfoMine USA, Inc., set out to build a suite of stand-alone software programs that would provide their clients the means to estimate the costs of developing and operating mineral exploitation projects. After the first program (Sherpa for Surface Mines) was completed and launched, the developer (me) left WME to form Aventurine Engineering, Inc., in order to complete the series of applications. In the years since, four programs have either been developed or upgraded and enhanced. Applications were produced that estimate the costs of underground mining, placer mining, and project site reclamation. In addition, an application specifically designed to evaluate the economics of these projects, which was based upon a program previously developed for WME by Bill Willoughby of Willoughby & Associates, was redesigned and the code updated to a MicroSoft compatible platform. All these programs follow an engineering-based approach to cost estimating. Instead of relying on rules-of-thumb and statistical averages, they calculate all of the engineering and operational parameters needed to estimate costs. The premise is that the uncertainty associated with cost estimates should lie with the data available for the resource, not the approaches used to design and estimate the associated design parameters. In other words, it is acceptable that items such as the resource grades, deposit dimensions, ore and wall rock characteristics, and mill recovery rates carry with them some uncertainty, but parameters such as loader bucket capacities, truck speeds, pump horsepowers, hoist velocities, and grinding mill diameters can be calculated (although uncertain data might be used in those calculations). No additional uncertainties should be introduced because the cost-estimating procedure relied upon statistical manipulation or anecdotal inaccuracies. To that end, the programs rely upon calculation-based approaches to selecting and sizing machinery, assigning the required workforce, and determining the extent of the consumables needed to recover mineralized material at a rate defined by the client. And while calculation-based software is not unusual, more modern approaches work toward the development, accumulation, and manipulation of data. INITIAL CONDITIONS AND PROJECT GOALS In 2016 we had five separate programs completely disconnected from one another. Each was written in VisualBasic, a language that was falling from favor. In essence, the status in 2016 was a series of stand-alone programs (Figure 1) in which results from one needed to be manually entered as input into another.

Jan 1, 2019

By Weibai Hu

The flotation separation of wolframite from fluorite and quartz is investigated with chelating agents and neutral oil as synergic collectors. Test results indicated that a-nitroso-ß-naphthol has a strong collectivity for wolframite and selectivity against fluorite and quartz. The 8-hydroxyquinoline has collectivity and selectivity also. They both have a better activity than sodium oleate. However, the cupferron is slightly inferior. The synergism of chelating agents and neutral oil looks promising, especially for fine wolframite particles. The activation effect of Fe2+ and Ca2+ ions on separation of wolframite from fluorite and quartz is slight. The UV absorb-spectra measurements showed that the adsorption of chelating agent on wolframite is multilayer, and flotation behavior is related to chemisorption. The chelating agent which bonds to Fe and Mn sits on the wolframite surface, and the reaction between Mn2+ ion with collector is more significant. The essentials affecting reagent activities are the bonding factor and the hydrophobic factor. These factors are discussed by structure-activity relationship theory. The synergism of neutral oil is a secondary collector likely to lengthen the hydrocarbon chain of chelating agents.

Jan 1, 1985

By Philip-Mark Spanidis, Christos Roumpos, Francis Pavloudakis

This paper presents a quantitative research (QNR) methodology, collaboratively conducted with a group of mining experts, to assess the knowledge management (KM) landscape in the Greek mining industry. The methodology involves a framework for structured data collection using questionnaires, statistical analysis, discussion on critical methodological aspects, and interpretation of results focusing on key aspects of interest for designers of KM systems. The paper concludes by summarizing the methodology’s outcome and proposing perspectives for further research.

Aug 1, 2024

This paper summarizes the process development behind the design of three different types of paste fill plants at operating Canadian hard rock mines. Each application has a unique paste backfill mix and process which utilizes the materials economically available to the mine site. The different plants produce paste fill composed of base metal tailings, a blend of recovered disposal pond tailings fines and alluvial sand, gold ore tailings, and a blend of gold ore tailings and alluvial sand. This work has led to the joint development by Inco and GL&V Ontario of the compaction storage mechanism for the de-watering of mill tailings to a paste consistency.

Jan 1, 1994

By Peter E. Hart

The search for mineral deposits is a difficult high-risk enterprise whose likelihood of success is influenced by a great many factors. Among the most important of these factors are the knowledge and judgment brought to bear on an exploration problem. If, for example, a panel of expert highly experienced geologists could be convened to examine every prospect, it is at least plausible that fewer deposits would be overlooked in the exploration process. Unfortunately, whether a project is undertaken by a private company or a government agency, it is not usually feasible to convene such a panel. Our purpose in this chapter is to describe an experimental system of computer programs called PROSPECTOR that is intended ultimately to provide expert consultation on problems of mineral exploration and resource evaluation. Ideally, PROSPECTOR would serve as a surrogate for a panel of expert economic geologists. However, because the cost of computation is very low and is projected to drop by a factor of about 100 over the next two decades, systems like PROSPECTOR could be made available to the exploration enterprise at large. When consulting about a prospect, the PROSPECTOR system first gives the field geologist an opportunity to tell the program about the most significant features of the site: the major rock types, minerals, and alteration products. The system then compares these observations with a number of stored models of various types of ore deposits and forms alternative hypotheses about the types of deposits that might be present. The system next engages the geologist in a dialogue in order to obtain additional data that would be useful in resolving the multiple hypotheses. The geologist can interrupt the system at any time to obtain clarifications of questions, volunteer additional data, request the reason a particular question has been asked, or obtain a general summary of the state of the consultation process.

Jan 1, 1979

By H. W. Gussmann, R. G. Rohrs, E. van der Merwe

Salinity in Effluents carries a high penalty as a result of toxic­ity, corrosion, limited re-use potential, scaling and environmental impact. Although the high TDS, such as Calcium sulfate, other than metals are still being dealt with a low key non issue basis, they are receiving more and more attention from regulators. Traditional solutions to solve these problems are costly and inefficient and create therefore severe constraints on the prof­itability of mining operations and out-price in general the finan­cial resources for environmental clean up operations. Going up the technology versus cost curve the most econom­ic solution to pollution is dilution but which is difficult in a coun­t1y shoti of water. If this can't be done, the second best, at least in sunny areas, is, to pump the whole effluent on a tailings dam for evaporation. Depending on the contaminants, one may have to pond the efflu­ent to avoid re-dissolution and seepage into the ground. The next most common solution to pollution is the addition of lime to remove and concentrate any dissolved metals and then dump the product, hidden in a mass of gypsum in a convenient place. Again ponding may be required to avoid ground pollution. However the treatment costs start to rise steeply if it is not allowed to discharge the limed overflow solution because of its high calcium sulphate content. Further treatment is then required in the form of high cost and high tech membrane process tech­nology such as reverse osmosis or dialysis or even mechanical driven evaporation.

Jan 1, 1998

By Laura Suarez, Jörgen Kajberg, Pär Jonsén

How does an investigation into the breakage characterization of electric arc furnace (EAF) manganese slags contribute to a more responsible usage of resources throughout the life cycle of steel products and reduction of carbon emissions? The main goal of this study is to increase the knowledge on the mechanical response of manganese slag to open the potential of pyrometallurgical residues to become secondary material in industrial applications such as infrastructure construction, fillers, binders and soil stabilization, among others.

Mar 1, 2024

By T. Bartnitzki, N. Fietz

"INTRODUCTION For a long time now automation has been state of the art in production engineering and chemical engineering. The advantages of automation are, for instance, higher reliabilities of production processes, higher product qualities as well as capacities and improved safety conditions for the personnel. In contrast, many operations in mining are still conducted manually by machine operators instead of autonomous control units. One example for this is the excavation of underground hard coal which is still executed with aid of human perception. The Institute for Mining and Metallurgical Machinery (IMR) has been working on possibilities for sensor-based automation of mining machinery for many years now. Thereto the focus is set on the implementation of common material analysis techniques into ruggedized conditions as a basis for automation. Laser-induced breakdown spectroscopy (LIBS) for instance is an atom emission technique which enables the determination of the elemental composition of a sample. After introducing LIBS this paper will give an overview on dust formation during the cutting process. With the illustration of a few examples the challenges in determining dust concentrations specifically such of cutting processes are explained in further detail. The final chapter will outlay the possibilities and challenges in utilizing cutting-induced dust for the automation of shearer loaders. LASER-INDUCED BREAKDOWN SPECTROSCOPY LIBS Fundamentals LIBS (laser-induced breakdown spectroscopy) is a contact-free method for analyzing materials in any state of aggregate. It pertains the atom emission techniques and is based on the generation of plasma, inducing avalanche ionization on the surface of a solid material or any spot in a gas or aqueous solution. With sufficient background information on the expected elements and an additional calibration, this method can determine all present elements not only qualitatively but also quantitatively. However, this method cannot be utilized for determining the molecular composition of materials – if this feature is required a complementary method such as Raman analysis needs to be added. (1, 2)"

Jan 1, 2015

By Ralph Spickermann

UK Seabed Resources (UKSR) signed a manganese nodule exploration contract with the International Seabed Authority on 8 February 2013 for a 58,000 km2 tract on the eastern edge of the Clarion Clipperton Zone (CCZ). UKSR is a private company based in the United Kingdom and established primarily to develop the commercial potential of the CCZ deposits. This is the first of many anticipated regulatory, market and technical milestones that are requisite for (1) environmentally responsible commercial scale production of nodule derived metals and (2) generation of revenue through their sale in the global commodities market. This presentation will describe the progress made to date in this effort and an industry-based perspective on the tasks and challenges that may lie ahead.

Sep 1, 2014

By R. W. Plume

Gold extraction along the Carlin trend requires large withdrawals of ground water, which can be perched, unconfined at shallow depth, and (or) confined at depth. Five hydrogeologic units-Quaternary basin-fill sediments, Tertiary basin-fill sediments and sedimentary rocks, Tertiary volcanic rocks, Devonian to Ordovician siltstones, and Devonian to Ordovician carbonate rocks--form the framework for two aquifer systems that discharge along some reaches of the Humboldt River and its tributaries and are recharged by streamflow along other reaches. Ground-water withdrawals eventually could affect these stream-aquifer interactions. Further work is needed to quantify regional hydrologic processes and evaluate potential effects of mining on water resources.

Jan 1, 1992

By John Drew Ridge

Recent work by Haas has made available information on densities and vapor pressures of solutions of differing salinities at temperatures up to 330°C. From these data it is possible to predict the behavior of volcanic exhalations of various degrees of salinity as they approach the sea floor. Particular attention is devoted to solutions of 5.0 weight per cent NaCl and 20 weight per cent NaCl, two fluids that approximate quite closely the salinities of what Roedder termed: (1) normal hydrothermal fluids and (2) fluids typical of stratiform deposits of low-temperature conditions of origin. It is apparent that solutions above 220-230°C. cannot reach a sea floor on which the depth of water is 600 feet or less in the liquid state but will boil at some appreciable depth beneath the sea floor. Such boiling would result in the precipitation of all constituents of the ore fluids of significantly lower vapor pressure than water. The principal such constituent would be salt, and no sulfide deposits, the major constituent of which is salt are known. It follows, therefore, that ore fluids probably never get close to the sea floor of shallow seas at temperatures high enough to permit boiling. Ore fluids significantly above 230°C. can reach the sea floor in the fluid state only if the depth of the sea in the area. in question is well above 600 feet, for example, solutions at temperatures of ±300°C. reach the sea floor in the liquid state only if the depth of sea water is slightly over 3000 feet. Ore fluids reaching the sea floor at such depths may be the parents of such fluids as the Red and Salton Sea brines. On the basis of these data, the Cyprus and Kuroko deposits are discussed.

Jan 1, 1973

The evolution of surface mine layout configuration is a function of the schedules and sequence of material excavation within the optimized layouts. The production schedules and sequence of materials movement from multi-bench and multi-face operations are difficult to plan and execute. However, the ability to maximize the profit or net present value of an orebody is largely dependent on the mining schedule. The mining schedule will determine the life of the mine, the projected cashflows, and the investment requirements over the mine life. The pit geometries, pit expansion rates and the periodic volume of materials from different benches in a multi-bench, multi-face open pit mine determine the equipment requirements. The volume of materials excavated, as well as pit layout changes from circular and elliptical geometries of an oil sands mine were modeled using analytical geometric and parabolic partial differential equations (PDEs) and solved within Matlab. The results show that the geometric values are almost the same as those obtained from PDEs for different pit configurations. The economic analysis shows that both the current mining system (CMS) and the cyclic excavator conveyor belt control system (CycEx CBCS) are viable with high NPV (= $3.20 × 1010), PI (> 19%) and IRR (> 29.02%) with short discounted payback periods (= 3.24 months). The CycEx CBCS option is more economic than the CMS option. Its NPV is 1.27 times that of the CMS option. The PI and IRR for the CycEx CBCS option are respectively 2.24 and 1.13 times that of the CMS option. As well, the CycEx CBCS option has almost half the DPBP of the CMS option. The CMS option has an operating cost of $1.386 per tonne ($2.774/barrel) while that of the CycEx CBCS option is $0.779/tonne ($1.558/barrel). These results show that the CycEx CBCS option is the better option for mining companies working on oil sands deposits to invest in.

Jan 1, 2011

By E. D. Stephenson

As part of the British Steel Corporation?s development plan during the 1970?s, it was decided to concentrate its bulk steelmaking processes based on the BOS at 4 major Works with access to deepwater ore terminals, for the supply of high-grade imported ores. These 4 sites were at: - 1. Rarenscraig Works in Scotland where the ore terminal would be hilt at Hunterston on the west coast some 50 miles away. Bavenscraig was already an integrated Works but suffered from having to discharge ore 27 Glasgow tenxinus on the River Clyde, which could only accommodate vessels up to 25,000 tonnes. In the future, ore was to be unloaded at Runterston and shipped by a rail-link into Ravenscraig, The new ore terminal would have the potential to unload vessels up to 300,000 tonnes. - 2. Port Talbot Works in south Vales where the existing harbour was developed to discharge large ore carriers. This again was an existing Integrated Works and the benefits of the new harbour also applied to Llanwern Works which was another integrated Works some 50 dies to the east, which would now receive ore from Port Talbot.

Jan 1, 1980

By H. Schubert

The flotation of sylvite and also some accessory minerals is performed in brines containing very high electrolyte concentrations. Under these circumstances the mechanims of collector adsorption exhibit some characteristics which will be discussed by significant examples: - flotation separation of sylvite and halite with n-alkylammonium salts and n-alkyl sulfates - flotation separation of kieserite and anhydrite with acylamino carboxylic acids - flotation of halite by collectors which are adsorbed by hydrogen bond formation.

Jan 1, 1988

By D. Newman

Multiple seam mining is prevalent in Southern Appalachia because economically mineable coal seams are numerous and frequently occur in close vertical proximity. West Virginia, Kentucky, and Virginia have 117, 55, and 40 mineable coal seams respectively. It is extremely rare to have an underground mine that has not been undermined, overmined, or has mining adjacent to it. In many cases the multiple seam mining is concurrent with extraction sequenced in superjacent seams. Because underground mining is focused on recovering the most valuable reserves, mining is rarely practiced from the top seam down, which is the practice most conducive to stability. The combination of room-and-pillar mining methods that include development only, small block, partial retreat, full retreat, and longwall mining produce a wide range of mining geometries and complexity in underlying and overlying seams. In the future, the number of multiple seam operations will increase as reserves are depleted and future mines are, by default, located closer to abandoned mine workings. The improved coal market has transformed many formerally uneconomically mineable seams into attractive reserves. The approaches and methodologies used for multiple seam stability analysis are dictated by the site conditions, including overburden/interburden thickness and lithology, mining geometry, and the mining methods in both the active and abandoned mines. Multiple seam stability analysis using analytical and numerical methods is illustrated by two case histories that reflect close proximity room-and-pillar mining and mining in bump prone situations.

Jan 1, 2007