Search Documents

By M. P. Valoski

In the United States, the occurrence of underground mine fires/explosions continue to decrease; however, they pose great danger to the miners and any subsequent mine rescue teams and/or fire brigades. Tragically, 19 coal miners lost their lives in 2006 at fires or explosions. Fires/explosions can devastate a mine and cause its permanent closure. It is vitally important to obtain accurate information on the gas content (concentration and composition) of the mine atmosphere after the event so that appropriate action can be instituted to rescue any trapped miners while not exposing the mine rescue teams to unnecessary hazards. Additionally, the fire fighting techniques (spraying water, sealing, etc.) will be dictated by the gas content. Finally, the gas content will determine when it is safe to recover the mine. The gas content of the air can be determined using detector tubes, handheld instruments, portable instruments, or gas chromatographs. No single instrument is suitable for all analyses. Each type of instrument has its advantages and disadvantages. This paper discusses these attributes.

Jan 1, 2010

By A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to a reduction in travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation nay be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways nay contribute to formation. The study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Company to identify causes of the problem.

Jan 1, 1982

By B. A. Slaker, T. Miller

"An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys, to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in) was measured by the extensometers, photogrammetric reconstructions, and laser scanner over a 6-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls was significantly lessened. INTRODUCTION Limestone formations in the United States can be subject to relatively high horizontal stresses due to the presence of tectonic loading of the strata. Horizontal stresses have a documented history of causing stability issues in underground limestone mines. Kuhnhein and Ramer (2004) discussed the influence of horizontal stress on complex ground control interactions associated with limestone pillar design and mine layouts. Esterhuizen et al. (2008) documented roof damage observations associated with high horizontal stresses such has roof guttering, beam instability, oval-shaped falls, and failure propagations. There have also been a number of documented case histories of horizontal stress causing unexpected roof and pillar failures at shallow depths (Stacey and Yathavan, 2003). To the knowledge of the authors, there has only been one well-documented case of floor failure causing stability issues in an underground limestone mine. Murphy et al. (2015) documented the role that a weak, moisture-sensitive floor had in the development of a massive roof collapse. For this paper, the study site neighbored, and was in the same general geology of, the site in Murphy et al. (2015). However, the weak, moisture-sensitive floor was not present for the current study. The current study site has experienced significant floor instabilities caused by high horizontal stresses. The instability area was monitored using two different methods to determine if the floor failure would eventually propagate into roof or pillar failure. The objective of this paper is to analyze displacement monitoring measurements from string potentiometers and remote sensing techniques in an area experiencing active movement. Based on the measurement trends and observed damage from inside of the mine, the presumed failure process will be discussed."

Jan 1, 2017

By Rubén Pavón] [H.

Mexico, that for various years held the second place among the elemental sulphur producers in the world, now occupies the fourth position. Nevertheless, taking advantage of the recent increase in the international prices of the metalloid, it is expected that Mexico recovers its traditional position producing, for the first time, over two million tons of sulphur during 1974. Drawing from material stockpiled during the last years sales are expected to reach 2.5 million tons, at excellent prices in the foreign markets, but not so in the domestic ones where prices have remained practically static since 1955, in spite of substantial escalation of production costs. Of the two sources of elemental sulphur in Mexico, the frasch process extraction from the salt domes of the Tehuantepec isthmus where the most important reserves are located - is the one that shall have an important increment. An increase of production of lesser magnitude is expected from sour gas, since sulphur recovery plants wilI go on stream toward the end of the year in the new oil fields recently located in the State of Chiapas. Two Mexican corporations are expanding and improving rational Frasch extraction operations. Together with Petroleos Mexicanos' sulphur recovery from sour gas it is estimated that production during 1975 shall reach 2.5 million tons and, consequently, supply the domestic market and generate an important sum of foreign currencies.

Jan 1, 1974

By Michael Stanwood

Project feasibility no longer involves just technical and economic viability-today's feasibility study must include environmental, regulatory, and political considerations as well. While the US now appears at least somewhat committed to developing synthetic fuels, including oil shale, it is the environmental issues, rules, regulations, and guidelines that will play the major role in determining the timing, magnitude, and overall scope of synfuel development in the coming years. The key environmental obstacle affecting oil shale development is uncertainty. Although oil shale may be the most environmentally studied "new" technology in the world, little is known with much degree of certainty about potential environmental consequences of one full-scale commercial facility, or the effects of a massive development effort in a relatively pristine and sparsely populated area. Other primary environmental uncertainties include: • Environmental compliance costs and their effects on investment decisions; • The reliability and acceptability of anticipated pollution control technologies; and • The confusing, time-consuming environmental regulatory framework, which requires more than 100 permits, clearances, and reviews before development occurs. This discussion will focus on the latter uncertainty, and will describe he current status of potential constraints to oil shale industry development in five areas: water availability; water quality degradation; air quality degradation; reclamation and spent shale disposal; and community impacts.

Jan 1, 1981

The heat of immersion of coals in different immersional liquids is measured as a function of particle size and moisture content. Decrease in particle size shows a concomitant increase in the heat of immersion. The heat of immersion is dependent upon the nature of immersional fluids. In addition the nature of moisture present in coal influences the heat of immersion.

Jan 1, 1993

By G. W. Phelps

This discussion deals with the geology o£ the Tennessee-Kentucky ball clay deposits; their mineralogy and chemistry; methods of finding, mining and refining; and makes observations on reserves of and future prospects for these clays. Ball clays appear in ceramic formulas for manufacture of vitreous china sanitary-ware, electrical porcelains, floor and wall tile, dinnerware and artwares(l). This type of clay is used for refractory (2) and abrasive products(3), and as a suspending agent for ceramic glazes(4), engobes(5) and porcelain enamel slips(6). Although some ball clay is imported, probably 85-90 percent of ball clay used in the USA(7) is obtained from deposits in Weakley, Henry and Carroll Counties in Tennessee(8), and in adjacent Graves County, Kentucky(9). The term "ball", as applied to clay, probably derives from former mining practice in England whereby conveniently-sized blocks of clay were cut from moist clay beds by spading(10), The expression "ball" has no other technological significance. ASTM(11) defines ball clay as "a secondary clay, commonly characterized by the presence of organic matter, high plasticity, high dry strength, long vitrification range, and a light color when fired." This, and similar(12) definitions, applies to English ball clays but is not satisfactory for many American ball clays. Geology of the Tennessee-Kentucky Ball Clay Deposits Figure 1 shows that most commercial clay areas of the eastern United States lie near the edge of the Coastal Plain; a skew-shaped configuration of its landward boundary outlines the Mississippi Embayment(13), Near the apex of this basin a broad plain, with a rolling, Bullied topography(14), dips gently westward from the Tennessee River to bluffs at the edge of the Mississippi River flood plain.

Jan 1, 1972

By D. Denton, L. Buckingham

The dry grinding and leaching circuits of the Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs. Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes. The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper. The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility. Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike.

Jan 1, 2001

By R. L. Wooten

When discussing what Coal Mine Safety in the future will be, it is important to examine three areas which at present provide significant parameters to the industry. These three areas are: 1) Safety improvements in mining equipment; 2) Labor-management relations; and, 3) The politics of coal mine safety. EQUIPMENT Over the past several decades significant safety improvements have been made in the types of equipment now in use in most operations. Many of these improvements have evolved through mandates from either the U. S. Bureau of Nines, MESA, MSHA; and in some instances, the states. Cabs and canopies are examples of federal mandates while the use of ATRS initially was a state mandate.

Jan 1, 1985

By W. Chae

The influence of solution ionic strength (IS) and electrolyte valence on the flotation behavior of malachite has been investigated. The microflotation tests were conducted over a range of solution IS (1?300 mM) at a constant speed (340 rpm), pH (9.5), flotation time (10 min), and sodium oleate dosage (5.3×10-7 moles/g). The size of malachite ranged from 45 to 53 µm, and two different types of electrolytes (NaCl and CaCl2) were employed. Electrophoretic mobility was also measured over the same IS range employed in the microflotation study. Overall, strong coupled effect of solution IS and ion valence was observed. Specifically, the flotability of malachite increased with increasing IS in the presence of monovalent cation (Na+) while the flotability increased up to 30 mM and decreased with increasing IS in the presence of divalent cation (Ca2+). Notably, the flotability of malachite was greater with the presence of Na+ compared with Ca2+ under high IS conditions (IS>30 mM). Consistent trend for Na+ versus Ca2+ was observed from the flotation results with different SO dosages. The characterization and flotation results suggested that the trend was likely attributed to the increased unfavorable interaction between malachite and bubble via the charge reversal of bubbles and malachite at higher IS in the presence of Ca2+.

Feb 27, 2013

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016

By R. J. Sweigard, R. V. Ramani

G.F. Learning The paper by R.V. Ramani and R.J. Sweigard is a wonderful description of the labyrinthine web that has been spun about the mining industry by energetic bureaucrats and politicians over the past 50 years. The remedy for the problem, however, is not more of the same, but less. That may be difficult for the industry to achieve, for it is not a technical solution but a political one. And the current fervor for more detailed planning at all levels of government and private enterprise has become deeply ingrained. The authors recommend the provision of more information about mining and mineral resources to "macro" (i.e., government) land use planners. They apparently overlook, however, the already strong tendency on the part of most government land use planners to consider themselves omniscient. Thus, giving them more information about the technical problems of mining will only make them want to get more and more involved in the "micro" (private, site specific) mine development and production plans of the individual mining firm. In fact, this has already happened at all levels of jurisdiction from municipal to federal government. Examples are legion. The most effective way to ameliorate the adverse impacts of government land use planning on existing and potential mining operations is to: (1) introduce greater flexibility in the definition of land use zones by local and state governments; (2) adopt realistic and relevant ambient environmental performance standards in governing relationships between mineral land uses and concurrent or subsequent nonmining land uses; (3) allow greater leeway for economic considerations in land use decisions in contrast to the explicit legalistic approach now in vogue; (4) recognize that all minerals are not the same and that sand and gravel mining should not be treated the same as underground metal mining, coal stripping, oil field production, or in situ leaching; and (5) eliminate the notion that mining operators should be responsible for determining in detail the use of land by subsequent owners of mined land. This last bit of conventional ethic really makes no more sense than requiring the builders of every shopping center or government office complex to provide detailed plans for the use of that land when its use for shopping or government is ended. Did the builder of Ebbetts Field plan for Brooklyn after the Dodgers went to Los Angeles? Should the developer of the Bingham Pit plan for suburban Salt Lake City after the copper mining goes to Chile? The nation's mining industry must address these questions before further bankrupting itself to provide more data to planners and spending thousands of dollars per acre to create land that when reclaimed is worth only a few hundred dollars per acre. Reply by R.V. Ramani and R.J. Sweigard We thank Mr. Leaming for his valuable contribution. His views on the problems of land use planning and mineral resources are most welcome additions to our paper. As the title indicates, our paper was more concerned with the impacts of land use planning on mineral resource conservation than with the details of the planning process. On the whole, his five recommendations would be helpful for mineral resource conservation. However, we would suggest that the argument he presents for his final recommendation does not address the differences between mining as a land use and commercial or institutional uses. We believe that this difference is the crux of the issue. We share Mr. Leaming's desire to ameliorate the adverse impacts of land use planning. Possibly the most detrimental impact is the loss of mineral resources. Any development, whether mineral or community, that does not give proper consideration to other resources can result in permanent loss or sterilization of resources. With proper planning, some of these losses can be avoided. As our paper indicated, one factor that limits the consideration of mineral resources, and ultimately leads to their sterilization, is the generally inadequate levels of resource characterization and understanding of the unique nature of mineral resources and mining operations. The last point raised by Mr. Leaming is also important. In terms of reclamation and land use planning in mining districts, we certainly do not advocate spending more than what the results are worth. The main thrust of the paper was to explore the avenues for conserving the mineral resources so that, at some appropriate time, the issue of mining and reclamation can still be addressed.

Jan 4, 1985

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ?Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions became the post-event conditions. ?Search for evidence that either denies or supports the various hypotheses. ?Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By R. V. Ramani, W. Miola

The MSHA prescribed method for the determination of quartz in airborne respirable-dust samples from underground coal mines is the P-7 method, a combination of low-temperature, radio-frequency ashing (LTA) and infrared analysis (IR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive infrared (IR), Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) methods are most commonly used for the analysis of quartz in powders. Several aspects of the experimental procedures, such as the preparation of the analysis sample from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist and data interpretation, affect the results from each of the methods differently. Significant differences in analytical results obtained from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All studies point to the need for reliable quartz analysis methods. In a recent research program, a procedure for preparing bulk-coal and host-rock samples for quantitative quartz analysis was developed. Further, the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle-size distribution, matrix and calibration on the analytical results. In this paper, several issues concerning the measurement of quartz in the samples of coal, host-rock and airborne respirable dust from mines are outlined and quantified.

Jan 1, 1996

By Jack R. Miller

This session has been organized to suggest to you that the development of direct reduction is important to the iron ore mining and coal mining industries. The papers presented this morning will include a discussion of the costs of making direct reduced iron (DRI), the iron ore and coal supplies needed to produce DRI, the financing of direct reduction (DR) projects and, probably most important, the impact of the DR development on the iron ore and coal industries. For starters, this opening presentation offers a brief statement about DR practice and DRI, under the title that should surprise no one: "Direct Reduction: What Is It?" There is always the chance? that a brief statement may become long and complicated. But, by mixing some slides borrowed from Hal Lownie with a larger number of photographs accumulated from other sources, I hope to avoid such pitfalls.

Jan 1, 1978

By V. C. Rogers, K. K. Nielson

INTRODUCTION An evaluation of the radiological health risks from uranium mining and milling requires the determination of several key parameters. As shown in Figure 1, the first step is the estimation of the radioactive source term. The radionuclides in the ore consist of the 238U decay series nuclides shown in Figure 2, the 235U series nuclides, and 40K. The 238U decay series isotopes dominate the source term, with the 235U series isotopes causing less concern and 40K remaining at background levels. [ ] Specifically, the risks from uranium mining and milling are mainly associated with 230Th, 226Ra, 222Rn, and its short-lived daughters. These radioisotopes are mainly alpha-particle emitters; hence, some dispersion mechanism is necessary to bring them into intimate contact with man so that they can be inhaled or ingested For water pathways, the leaching of the isotopes from [ ] the solid ore or tailings provides a measure of the amount of contaminant initially available to the environment. For the air pathway, dust-creation mechanisms such as blasting, crushing or general resuspension processes dominate for 226Ra and 230Th. However, 222Rn, being a chemically inert gas generated from the decay of 226Ra, can migrate through the ore, overburden and tailings over considerable distances. As shown in Figure 1, the next step in the pathway to man is environmental dilution and delay. For the water transport mechanism, the delay in the isotopes reaching an accessible water supply may be considerable (several thousand years or more), but for airborne nuclides the dispersion in the atmosphere is rapid and constitutes the main mitigating factor. Considerable ventilation is provided in underground mines to dilute and remove radon and its daughters in order to keep their concentrations low and thereby minimize their inhalation by miners. The rate of uptake by both the workers and the general public is often difficult to ascertain. It involves breathing rates, rates of water consumption and other poorly-defined parameters. The final steps are the risk estimators used to predict doses and cancer rates from the inhaled radon daughters and ingested or inhaled radium. Many

Jan 1, 1981

By Koehler Stout

Stopewall or room closure can be a problem in nining operations. In some mines, wall closure causes ore passes and nanways to collapse when they are enclosed in nine fill. When this phe- nomena occurs, heavy ground and, or, rock bursts frequently happen. Often, ground problems become progressively worse as mining in the stope block progresses toward the upper level. The sill and pillars in the level above may experi ence heavy ground and bursts. Sometimes the conditions get so bad in the stope that it is unsafe to mine the ore, so the stope is abandoned and the ore is lost.

Jan 1, 1980

By Stuart K. Nicol, Malcolm D. Engel, Neville T. Moxon

Ion flotatir,n of gold is a process being developed to selectively float extremely dilute aurocyanide liquors using a novel surface active complexing agent. The principle of ion flotation is also applicable to a wide range of other metal-containing solutions. The market potential of the gold flotation process would be enhanced by the possible combination of the gold recovery capabilities with both cyanide recovery and metal removal. For example, recovery of copper cyanides from a return liquid strean1 would be a useful means of reducing operating costs and satisfying environmental pressures to treat tailings dams. Experimental work is described where samples of tailings solution from a far north Queensland gold mine were subjected to ion flotation to remove copper cyanide species from a clear recycle solution. The form in which these products was removed was of secondary importance compared to the need to produce a clean solution for use in the plant. Recovery of the anionic copper cyanide species was accomplished using a quaternary ammonium surfactant.

Jan 1, 1991

By N. A. Abdel-Khalek

An experimental study was carried out to compare the results of laboratory column flotation versus conventional flotation for the cleaning of fine coals of different rank and their oxidized samples as well as discrete size fractions. Surface oxidation caused a significant reduction in the flotation yields achieved with both methods. However, the column flotation produced concentrates? of lower ash content. The recovery -size curve achieved with column was similar in shape to that obtained with conventional cell, with superior results in the region of fine fractions. The influence of some column operating parameters was also discussed.

Jan 1, 1990

By Descour Jozef, Suguru Shirasagi, Takuji Yamamoto, Koji Murakami

For TBM tunneling no visual inspection of excavated ground is possible. This may hinder the high-speed excavation, particularly in complex ground conditions. The TBM Excavation Control System was developed for better prediction of geological conditions ahead of the tunnel face during excavation. The seismic reflector tracing produces volumetric images of anomalies in the ground in “near-real time.” These images are verified using logging data from pilot boring and TBM driving data, to improve reliability and precision of ground mapping. Also good correlation was obtained between the rock strength index computed from TBM data, and one derived from volumetric seismic images.

Jan 1, 2007