Search Documents

By E. M. Wilde

Through the USGS's National Coal Availability program, coal resource appraisals have been completed for three 7.5-minute quadrangles (Willow Crossing, Colstrip East, Colstrip SW) in the Powder River Basin area of southeastern Montana. Available coal reserves (original reserves minus tonnages affected by current restrictions) vary from 44 to 70 percent of the original reserves. Major restrictions impacting each area also vary. In each area, one or two beds contain most of the reserves, but up to eleven beds contain available coal. The main beds in completed studies are the Knobloch, Rosebud, Sawyer and Flowers-Goodale. Three additional areas (six 7.5-minute quadrangles) are in preparation.

Jan 1, 2001

By Peter G. Sechiari

The Rio Tinto-Zinc Corporation Limited (RTZ), through it exploration company Riofinex, commenced exploration for bauxite in the Amazonia region of Brazil during 1970. Following' encouraging indications, exploration licences were taken out and an exploration programme was initiated In February 1975, a preliminary 'feasibility report indicated that a project, based on the Miltonia plateau located close to the town of Paragominas in the State of Para, was viable and that barging might offer an economic solution to getting the product to an ocean-going port. A, decision was taken in April 1975 to proceed with a full feasibility study. In the latter stages of the study, an engineering consortium of Mendes Junior and Bechtel do Brasil was employed to review, and modify if necessary, the concepts that RTZ had developed for the project's operation. With these concepts agreed, the consortium was requested to make capital and operating cost estimates, and these became available during February 1978. The deposit is being developed by a Brazilian company Mineracao Vera Cruz S.A. (MVC) in which the present share-holding is owned 64 percent by RTZ and 36 percent by Companhia Vale do Rio Doce (CVRD). RTZ is a British based international group of mining and industrial companies with interests in almost every major metal and fuel. CVRD is a Brazilian mining company, 85 percent owned by the Brazilian Government, with a major interest in iron ore and also other non-ferrous metals. It is intended, in due course, that the company will become majority owned by Brazilian interests.

Jan 1, 1979

Newmont has been producing gold from the Carlin Trend for over 45 years. Naturally the focus, scale and complexity of the operations have changed considerably over this time. Newmont discovered and developed the Carlin Main ore body which is located about 32 km (20 miles) north of Carlin Nevada. The property was developed as a one mine one gold mill treatment plant operation which produced about 6,200 kg (200,000 Troy ounces) of dorè gold bars per year. The initial mine, mill and gold refining facilities were relatively small in comparison to today?s standards. The milling circuit used the Merrill-Crowe zinc precipitation process to recover dissolved gold and prepare a concentrated precious metal ?precipitate? to be melted into a dorè bar for sale.

Jan 1, 2012

By R. S. C. Rogers

The present study examines the use of two vs. one stage of hydrocyclones in a pilot scale ball mill circuit. The approach used for doing this is based on computer simulation with mathematical models that explicitly account for the grinding mill/classification system interaction. Parameters for the ball mill model are obtained using a short-lived radioactive tracer method in open circuit tests of the study mill. The hydrocyclone model, based on the size selectivity concept, is developed and validated in standalone testing of the study hydrocyclones. Simulation procedures are validated through actual tests of the closed circuit grinding configurations of interest. Results of the evaluation indicate that two stages of hydrocyclones in the study circuit would improve classification, increase productivity and lead to more closely sized circuit products when compared to the conventional one stage hydrocyclone circuit. A computer simulation approach for comparing these circuit configurations in larger scale grinding circuits is also suggested.

Jan 1, 1981

By Norman K. Olson

A geologic investigation of mineral resources in South Carolina first began in 1825 when the General Assembly authorized Lardner Vanuxen to conduct a "Geological and Mineralogical Survey of South Carolina." Vanuxen, South Carolina's first State Geologist, reported in 1826 on the limestones (marble) of the Piedmont which during those early years, were burned in many shall, scattered kilns in the region wherever suitable raw material was available. He also mentioned the possibility of using marl from the Atlantic Coastal Plain province for direct application and enrichment to the soil. Since before the year 1844 industrial minerals in South Carolina have been commercially produced literally from A to Z, asbestos to zircon. The first pub¬lished reports of actual commercial production, not just an occurrence, are referenced in Table 1 for 33 known industrial minerals and rocks in South Carolina. Known or suspected occurrences of undeveloped non-metallic mineral resources in South Carolina await future verification by geologic mapping, sampling (including coring), possible beneficiation, and market analysis. These industrial minerals and rocks include, but are not limited to, special, clay minerals (e.g. bentonitic clays, zeolites and others), sillimanite, argillite (lightweight aggregate), kaolin (alumina) and marl (underground storage and tunneling medium). In addition other non-metallic minerals, once mined but still worthy of reconsideration, include topaz (industrial), heavy minerals, barite, feldspar, and monazite. Finally, possibilities for new reserves, as an expansion of existing mine output, might develop for fuller's earth, limestone (lime), sericite (finely divided mica), vermiculite, kaolin (paper coating and filling, other filler), and metallurgical gravel. Official South Carolina data from the U. S. Bureau of Mines for 1974 indicated a total value of mineral production of $105.2 million. During 1974 production consisted of cam-on clays, (brick and tile), fuller's earth, kaolin and vermiculite

Jan 1, 1977

By C. Alan Tapp

Introduction Mine sampling determines the practicality of any mining operation. Improper sampling can result in an incorrect appraisal of present production and future potential. Therefore, the mine department in charge of ore-reserve calculations and mine sampling should be overseen by competent and experienced professionals with technical backgrounds qualifying them to produce accurate results. Sampling is a process by which portions of an ore body are collected and analyzed to estimate the average mineral content of the entire ore body. It is incorrect to assume that a large number of samples eliminates any errors in the sampling method. To obtain unbiased samples, proper sample location with respect to rock type and mineralization is just as important. The sampling procedure must yield correct results for the type of mineral deposit, and careful consideration should be given to whether or not the sampling technique has been developed to an extent sufficient to eliminate as much human error and bias as possible. Only after the ore has been mined and milled is the sampling accuracy known. Sampling also provides information about the bulk composition of the ore for mineralogical and metallurgical tests that determine the economic ore-waste boundaries and the geologic trends for exploration. Actual mining plans can be developed from this information to maximize profits. Accurate sampling is critical, and thus must be approached in a scientific manner. Sampling Techniques Sampling practices and techniques are as varied as the mines in which they are used. The method(s) chosen must be tailored to suit the company and mining needs. For instance, tabular uranium deposits, vein gold deposits, and porphyry copper deposits pose special problems in conducting unbiased sampling. The mine geologist or engineer in charge must develop a sampling method, test it in a sample area, and then critically evaluate the results. If the results from the test area are accurate within the economic limits established by the company, they then may be adopted for general use in the mine. Four routine sampling methods are suitable for specific sampling objectives in the daily mine routine: (1) channel sampling, (2) chip sampling, (3) grab sampling, and (4) bulk sampling. The final sampling results depend upon how the four methods are combined to accurately determine the grade of the ore body. When used in conjunction with each other during different stages of mine development, the channel, chip, grab, and bulk sampling methods provide an in-house check or a comparison by which mining methods and sampling procedures can be evaluated. However, the most valid check is based upon the daily mill production. Channel Sampling Channel samples consist of cuttings collected from a groove cut into the rock about 102 mm (4 in.) wide and 19 mm (0.75 in.) deep. Various tools ranging from a 1.8-kg (4-lb) hammer and moil to a pneumatic chisel can be used to cut the sample. Accessibility and rock hardness determine the applicable sampling tools. Before attempting to take a sample, the rock surface must be cleaned thoroughly; the method of cleaning depends upon the amount of mine dust accumulated on the surface or the degree of alteration of the rock surface. Typical cleaning methods 'employ a wire brush, water, or chipping a fresh surface. Next, the sample outline is marked on the prepared surface, taking care to choose appropriate sample loca- tions. After determining the proper sample outline and length, the sample can be chiseled out, catching the rock fragments on a canvas tarpaulin on the floor, in a powder box, in a canvas bag to avoid contamination, or by some other suitable means to capture all of the sample. Vertical veins present a special problem because the drift's back usually is arched, not square. For example, Fig. 1 shows that if sample intervals are measured from A' to D', the length of the sample interval is greater than the true vein width, resulting in an incorrect calculation of the ore reserves. The correct method would collect three samples at A'-B', B'-C', and C'-D', using either actual measurements in the mine represented by A-B, B-C, and C-D or trigonometric calculations to determine the true ore thickness. Then, each sample can be weighted by grade and true thickness for the vein. Channel lengths usually are a maximum of 1.5 m (5 ft), and it is good practice to divide longer samples into smaller intervals according to structures, changes in rock types, or differences in rock hardnesses. The influence of those features on the mineralization then can be determined. Chip Sampling Chip sampling is a variation of channel sampling used when the rock is too hard to channel sample economically or when little variation in the mineral content indicates that this sampling method will yield results similar to those of channel sampling. Rather than cutting a channel in the rock, small chips are flaked off at regular intervals over the entire face or area being the mine. sampled. Care must be taken to assure that the sample is representative of variations in the rock hardness and type. hi^ method is fast and useful in preliminary evaluations, but it should not be used for quantitative ore-reserve calculations. Grab Sampling Grab sampling is a fast method for double checking either channel or chip-sampling procedures, and, in some instances, mine production can be estimated from carefully taken grab samples. Grab sampling takes equal amounts of material at selected intervals over a mine dump, a muck pile, or from an ore car to estimate its Channel Sampling mineral content. Generally, this method is not considered reliable. Many independent variables can affect this type of sampling process. Thus, if the ore occurs in the softer fraction and a proportional amount of the result-

Jan 1, 1982

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By Basil S. Fee

INTRODUCTION Probably the most important family of chemicals used in mineral processing today is a category of basic commodity chemicals loosely denoted as pH regulators. Typical chemicals which are referred to as pH regulators include lime, magnesium hydroxide, soda ash, caustic soda, ammonia, sulfuric acid, and hydrochloric acid. These chemicals are often used in very significant amounts in almost all of the major mineral processing operations such as flotation, hydrometallurgy, etc. (in dosages up to ten pounds per ton of feed ore treated). While cheaper in cost per unit weight of chemical than more specific chemicals such as collectors, frothers, extractents, etc., the overall cost to the mill operator is generally higher with pH regulators per ton of ore processed than with any other given processing chemical. For example, a rough rule of thumb in sulfide mineral flotation is that the cost of lime is double that of the collector(s) used. The symbol pH is used to designate hydrogen ion concentration. When acids, salts, and bases are dissolved in water, individual molecules are dissociated into their constituent radicals or ions. The strength of an acid or a base increases with the extent of such dissociation or ionization. An alkaline solution is one in which the number of Qydroxyl ions (OH ) exceeds the hydrogen ions (H ). In an acid solution, the hydrogen ions predominate. In either case, both ions are always present as water itself ionizes to a limited extent, that is: [ ] The pH scale is logarithmic and the pH value is the negative of the logarithm (base 10) of the molar concentration of hydrogen ions per liter of solution. For example, a pH of 5 means that the molar concentration of hydrogen ions per liter is 0.00001 (1 x 10-5). Likewise, a pH of 9 means that the molar concentration of hydrogen ions per liter is 1 x 10-9. Normally, the relationship between hydrogen ion and hydroxyl ion concentration is based on the relationship: Concentration of H ion x concentration of OH- ion = constant. Eq. (1) In dilute and/or moderately concentrated solutions that are normally used in mineral procygsing processes, the constant at 25°C is 10-14. On the pH scale, the value of pH equal to 7 represents the hydrogen ion concentration of a neutral solution. pH values lower than pH 7 indicate increasing acidity and higher values than 7 indicate alkalinity. Table 1 shows the nature of the pH scale at 25°C. Temperature affects the extent of ionization of dissolved acids, salts, bases, and water so that the hydrogen ion concentration (hence pH) of a solution is also affected by temperature. As a means of demonstrating this dependency, Table 2 shows the change of the exponent of the constant (base 10) in Eq. 1 and the pH value corresponding to neutrality as a function of temperature. It is also important, for example, that alkalinity or acidity expressed by pH not be confused with total alkalinity or total acidity. For example, total alkalinity is commonly determined by titration with a standard acid solution (usually HC1). pH is a measure of the hydroxyl ion concentration of an alkaline solution, whereas titration is a measure of an alkaline solution's acid neutralizing capacity. Thus, if one takes a series of various alkaline solutions prepared using different chemicals but all of exactly the same pH (and temperature) and then subsequently carries out a titration on each solution with a standard acid, it would be observed that the various alkaline solutions would neutralize entirely different amounts of acid. As an example, 0.08 grams of caustic (NaOH) , 6.32 grams of soda ash (Na2CO3), and 8.17 grams of ammonium hydroxide (NH4OH) all have a pH of 11.3 at 25°C. One liter of each of the above solutions neutralizes 0.073, 4.348 and 8.496 grams of HC1, respectively. Therefore, depending on the specific use of any given pH regulator, special tests need to be run by the mill operator to determine factors such as: the specific technical goals to be accomplished by

Jan 1, 1986

By Gary Almeraris, Vincent Jr Tirolo

Traditionally, “Means and Methods” were the sole responsibility of Contractors. However, because of a number of litigious projects in the 1970s, Owners and their Engineers began including Suggested Methods of Construction (SMC) in Contract Drawings. By the late 1990s these SMCs were becoming baseline “Means and Methods” with Contractor recommended changes often considered as Value Engineering proposals. By 2004, the word “Suggested” was sometimes changed to “Prescriptive.” Owners are also purchasing TBMs and other mining equipment for Contractors prior to bid. Is limiting the contracting community’s innovation in developing their own “Means and Methods” and selecting their own equipment in the best interests of the Owner? Does it reduce the Owner’s, Engineer’s or the Contractor’s risk? Are claims reduced and finally what is the impact on the bid? A questionnaire was sent to more than fifty senior engineering field and management personnel representing more than 30 heavy construction companies to ask their opinion on these questions.

Jan 1, 2005

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By David S. Cahn

For many years the green and dry compressive strengths' of pellets have been, considered as possible criteria of pellet performance during induration. Although widely quoted throughout the industry, little attention has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of the test. The purpose-of this study was to compare the constant deformation rate test with that using a constant loading rate in addition, the dependence of these tests on such pellet properties as size, weight, and method of balling was to be investigated.

Jan 1, 1967

By James A. Berberick

Research methods to develop an economic model for the determination of regional mineral advantage are discussed. An industrial complex conceptual framework is used to study potential mineral resource outputs of Kansas. A procedure for making a comparative cost analysis of potential outputs for a Kansas-based industrial complex is outlined and illustrated. Methods for estimating aggregate demand and for developing an input-output matrix for a hypothetical limestone complex are explained. The input-output matrix is expressed in physical units. A computer algorithm for converting physical production data and input cost data into total cost per unit of output information is briefly explained and flowcharted. Limitations and usefulness of this procedure in determining regional advantages are surveyed.

Jan 1, 1969

By G. Babut

The restructuring of mining operations in Valea Jiului coal basin imposed by the transation to the market economy calls for an increased coal production. Under the circumstances, the role of drainage networks grows ever more important. The paper describes an original mathematical model and software developed on its basis, with enables the ventilation engineer to assess the configurations of different systems, as well as to test their reliability and prognose their future performance before conceiving another methane drainage system or changing the existing one. The paper also includes the underlying principles of an optimization program for methane drainage networks, which will enable the detection of the optimal methane drainage system, both from a technical and an economic point of view.

Jan 1, 1996

By B. A. Waite

The new OSH regulations concerning ground ward monitoring of underground coal mines has been the source of many concerns for the mining industry. Because the regulations were initially written at the federal level but are being administered at the state level, considerable confusion exists within the industry as to what is actually required. Based on the preparation and submission of over 30 monitoring plans for existing deep mines in Pennsylvania, West Virginia, and Ohio, we now have a very good feel for the detail the monitoring plans, as well as the costs to im plement the plans. We do not, however, feel confident in our evaluations of the long-term impact the ground water monitoring regulations may have on the industry.

Jan 1, 1980

By Poltak Sinaga

PT Kaltim Prima Coal?s 13.1 km overland conveyor (OLC) was commissioned in 1991. It is of conventional 3 roller 350 trough belt type. Cost and performance optimization during initial design ended up with 5.4 mps belt speed, 1000 mm belt width to convey 1350tph, and 7 mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30 mtpa (million ton per annum). Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4 200 tph satisfactorily.

Jan 1, 2008

By W. W. Dudley

The U.S. Geological Survey, in support of underground testing of nuclear explosives, has developed a technique (Dudley, 1910) to predict the inflow of ground water to large underground chambers that are cylindrical in shape. By treating the chamber as a large-diameter well pumped at constant drawdown, the nonsteady discharge can be computed by the method of Hantush (1961) for analyzing flowing wells under leaky artesian conditions. In mining applications, whether for mineral recovery or for nuclear testing, the most serious departure from the conditions of Hantush's model results from the gradual enlargement of the opening under drained conditions. Inherent in the analytical technique is that the "well" is fully completed at the time that dewatering begins. Because safety is the prime concern, however, initial pumping systems or personnel evacuation procedures must be designed to handle the greatest conceivable inflow. DEFINITIONS Because somewhat different meanings are attached to similar words in different technical fields, the U.S. Geological Survey definitions (Lohman, 1970) of several hydrologic terms used in this report are given below. An aquifer is a formation, group of formations, or part of a formation that contains sufficient saturated permeable material to yield significant quantities of water to wells, and springs. A confining bed is a body of material lying stratigraphically adjacent to one or more aquifers and having a hydraulic conductivity distinctly lower than that of the aquifer. The total head (dimensions L) of a liquid at a given point is the sum of three components: (1) elevation head, he, which is equal to the elevation of the point above a datum; (2) pressure head, hp, which is the height of a column of static water that can be supported by the static pressure at the point; and (3) velocity head, hv, which is the height the kinetic energy of the liquid is

Jan 1, 1971

By S. M. Smouse

Total world energy consumption is projected to continue its strong growth of recent years. Because coal is the most abundant fossil fuel, it will likely remain an important energy source, particularly for power generation, into at least the early years of the next millennium. Clean coal technologies are available today that can economically reduce air pollution, primarily SO2 NOx and particulates, and for the higher efficiency technologies, CO2, from power generation. U.S. Department of Energy analyses show that the adoption of clean coal technologies could decrease carbon emissions worldwide while creating a strong export market with attendant creation of jobs in the U.S.

Jan 1, 1998

Inn mining communities throughout the western United States, cows have always been part of the landscape as they graze on surrounding rangelands. Until recently, mining companies regarded these animals as something to be kept off their properties — especially any freshly reclaimed lands. During the last few years, though, this situation has begun to change. Today, cattle can be seen in a handful of mine settings, moving up and down the slopes of mine tailings and waste rock. These animals are being used by several companies to do some of the reclamation work once performed by large earth-moving equipment, mechanical spreaders, rippers and seed drillers. This is because cows can contour slopes more naturally and produce and spread soil nutrients in ways that tractors and ripping machines cannot.

Jan 1, 1999

By David R. Kalasky

One of the primary areas of computer application in mine ventilation has been the analysis of mine ventilation networks. A variety of network analyzers that are aimed toward the solution of flows in a given network has been developed. These programs typically use the Hardy Cross or other iterative algorithm for solution of any network, even those that are complex. The computer software has become more efficient and sophisticated over time and has thus been widely adopted for ventilation network analysis. One of the shortcomings of these programs is that they have been developed with the idea of analyzing the ventilation requirements at a single point in the lifetime of a mine. This provides the ventilation engineer with an important tool for analysis but falls somewhat short of providing a convenient means to economically com- pare alternative methods for ventilating a mine. The program described in this paper provides such a tool. The principal concepts that were necessary for the completion of a computer program that analyzes ventilation alternatives is the capability of efficiently determining the ventilation requirements at a variety of times during the lifetime of the ventilation system and some method of analyzing the costs of the alternatives on a realistic comparative basis. To accomplish this task, the authors began using Penn State's mine ventilation simulator designated as PSU/MVS, Didyk et al. (1977a, 1977b) and added the necessary additional software to accommodate the need for multi-period, time-dependent analysis of the net- work. The software was then tested on a coal mine ventilation problem with a 23-year life. The problem points out the value of such a program for ventilation analysis.

Jan 1, 1986