Search Documents

By Tung Vu, Michael Harrington

"The Regional Connector project is a complex subway light-rail project that runs through the heart of downtown Los Angeles, CA. The design-build contract was awarded in April 2014 to the Regional Connector Constructors (RCC), a joint venture between Skanska USA Civil West California District Inc. and Traylor Brothers Inc., and their designer team consisting of Hatch Mott McDonald (HMM) and subconsultants. The project broke ground on Sept. 30, 2014 and is expected to be completed in winter 2021-2022. The main components of the project consist of 6.4-m (21-ft) diameter twin-bored tunnels, three crosspassages, a 87-m (287-ft) long crossover SEM cavern, three new underground stations, and cut-and-cover tunnels along South Flower, Alameda and 1st Streets. The project map is shown in Fig. 1. The design and construction challenges associated with each of these main components are discussed in the following sections.Project designTunnels. The Regional Connector tunnels are located primarily within the Fernando formation consisting predominantly of extremely weak to very weak, massive, clayey siltstone. About 305 m (1,000 ft) of tunnels on the eastern end are in alluvium and mixed face of Fernando formation and alluvium. The tightest curve of the tunnel alignment is 178 m (583 ft) in radius. The tunnels were designed with a reinforced precast concrete tunnel lining (PCTL) to be used with an earth balance pressurized (EPB) tunnel boring machine. The PCTL ring is 5.5 m (18 ft-10 in.) inside diameter, 27 cm (10.5 ft) thick, 1.5 m (5 ft) long, and consists of five segments and a key. The segments were designed with 6,500 psi concrete, 80 ksi yield strength wire rebar, convex joint surfaces to enhance seismic performance, and a dosage of 1.7 lbs polypropylene microfibers per cubic yard of concrete for fire resistance. The rings are designed with a right ring and left ring pattern and a taper of 3.8 cm (1.5 ft) to allow for alignment curve negotiation. Figure 2 shows typical sections of the PCTL. The structural lining design was modeled using FLAC 3D. Four consecutive rings were modeled with 32 dowel connection. Loading considered in the lining design includes temporary ground load during excavation, long-term ground loads, seismic loads and train loads. The seismic loads on the PCTL were simulated with the racking deformation applied at vertical boundaries of the model. Due to variation of geologic condition along the tunnel alignment and different surcharge requirements, three different types of reinforcement (typical, heavy and extra heavy) were designed. The typical type PCTL was required in Fernando formation, the heavy type was required in alluvium or mixed-face condition, and the extra heavy type was required in alluvium and underneath the Japanese Village Plaza where a surcharge of 1,000 psf was required."

Sep 1, 2019

By Todd Minoski, Matthew McElhinney, Mark Mazzella, Morgan Sears, Craig Compton

The National Institute for Occupational Safety and Health (NIOSH) is staffed with Engineers, Geologists, and Field Technicians conducting a variety of ground control research. The mission of the ground control teams within the Mine Systems Safety Branch (MSSB) is to eliminate ground failures leading to mineworker injuries and fatalities. Advancing the science behind ground control relies heavily on conducting mutually beneficial research at participating mines which is detailed in specific references throughout the paper. The ground control teams have several types of field instruments at their disposal to measure the ground response in underground mines. These include borehole pressure cells (BPCs), vibrating wire stress meters (VWs), hollow inclusion cells (Hi-Cells), roof and rib extensometers, load cells, and convergence meters. These instruments are used to measure changes in pressure, strain, and displacement within the underground environment. Instrumentation data is collected automatically using intrinsically safe or MSHA permissible dataloggers if required. Information is transmitted to the dataloggers using approved cable to distances of 200–1,000 ft. depending on the type of datalogger being used. Once mining is completed, the dataloggers are retrieved and brought to the surface, providing in-mine data to mine management and engineers for the conditions currently being encountered in a particular mine. This data, in conjunction with geologic data and stress mapping, can be used to validate numerical models. The practical application of these models is extremely important for mine management and engineers, particularly when faced with more challenging mine environments. Insight gained from applying these models can be used to make better engineering-based judgments for areas that will be mined in the future. The impact of such applications can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 1, 2024

By Z. Sample, S. Kaushik

"INTRODUCTION Industries around the globe have been making significant advancements in recent years due to innovations in automation technology. With the implementation of modern automation technology, professionals in process automation or plant operations can expect significant and exciting change, and the mining and mineral processing industries are no exception. From 2000 to 2010, the International Council on Mining & Metals (ICMM) reported that an increased output and increased value of most metals has resulted in a rise in global metal and mineral process industries from $214 billion to $644 billion. [1] Since most productivity increases in mining and mineral process industries have been achieved through the ability to process lower grade ores with improved efficiency and larger equipment, these industries have begun to adopt advanced automation and control technologies. Despite a growth slow-down, the mining and mineral processing industries are poised for continued and sustainable growth and development due to an increasing demand for energy minerals and emerging technologies requiring minerals and metals previously not demand. However, as these industries becomes more automated, new challenges are arising on the horizon. DEMOGRAPHIC TIME BOMB John Payne from BP is credited with first using the term Demographic Time Bomb to describe the upcoming crisis in the process industry in finding experienced operations personnel. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years. This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, this implies that these skilled mining and mineral process professionals are an aging population with irreplaceable knowledge and experience that are expected to retire in the next 5-10 years. While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences."

Jan 1, 2015

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

This paper presents the results of an investigation into the effect of pore pressure regime on the factor of safety (FS) and the anticipated critical failure mechanism for a fly ash storage facility. In this study, pore pressure measurements from standpipe piezometers and pore pressure estimated from seepage analysis were used for a comparison of the estimated FS for a fly ash slope. This comparison was applied for static and seismic scenarios. To account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation, a probabilistic analysis was performed. The slope stability analysis was conducted in 2D and 3D, adopting the limit equilibrium analysis approach, and a finite element seepage analysis. The results suggest consistency of failure surfaces for 2D and 3D and an increase in FS values of 5 percent for the 3D approach, limitations of standpipe piezometers. The study demonstrated the sensitivity of the FS value, and the implication of adopting representative material properties, and water table levels, especially in cases where limited data are available, and assumptions need to be made to assess the long-term stability of a fly ash dam facility.

Aug 1, 2024

By Alan English

This paper reviews the process control systems used in early commercial pelletizing plants, traces the development of these systems into present day practice, and briefly outlines advanced automation concepts being considered for future installations. It deals specifically with controls for the balling circuit, pelletizing machines, and related material handling and combustion equipment. The importance of instruments for visual observation and data logging is discussed, and the potential use of computer control is evaluated.

Jan 1, 1965

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By T. R. Ellis

Australia’s mineral valuation code continues to evolve, while mineral valuation standards are also being written for Canada and Southern Africa. The author is leading a task force for writing the extractive industries addition to the International Valuation Standards. Meanwhile, the International Accounting Standards Board is continuing the development of an extractive industries addition to its International Financial Reporting Standards, with an emphasis on valuation reporting. This paper analyzes the need, content and ownership for a U.S. minerals appraisal standard in the context of both these developing international standards and also existing U.S. regulations and appraisal standards. The author provides many questions for research and debate.

Jan 1, 2003

By J. Fisher, M. Barish

Over the past several years, Somerset International has successfully installed over 20 patented Sub325® Fine Coal Recovery Systems in the United States, Australia, Canada and Russia. These installations recover between 5 TPH and 40 TPH for the host sites. In addition to the increased revenue from the direct recovery of a recirculating load (Screen Bowl “Insurance”, Direct Recovery vs. Indirect Recovery via Recycle, CPSA 2020), host sites have seen benefits ranging from improved operation of refuse equipment to a reduction in the solids content of the refuse streams. As Somerset has improved ultra-fine coal recovery through the introduction of Sub325® Effluent Flotation and, most recently, the Sub325® Effluent Settler™, the amount of coal that has been recovered from these systems has increased by up to as much as 25%. Many host sites have taken a sense of ownership in the Somerset system and consider it to be a critical circuit in the overall optimal performance of the plant. In the past year, Somerset has taken the initiative to expand upon the capabilities of the Sub325® Fine Coal Recovery System, primarily the Sub325® Solid Bowl Centrifuge, to include Refuse Tailings Dewatering to allow for co-mingled refuse disposal. As slurry ponds and boreholes are becoming difficult to impossible to permit and operate, there is a need for a reliable, low-maintenance, continuous operation that can produce a handleable refuse cake. Refuse tailings disposal applications are by no means limited to coal plants and impoundments. Somerset has successfully tested at iron ore and phosphate locations throughout the world and have begun commercial installations. The ability to dewater -325 mesh material, whether it be coal, coal refuse, iron ore tailings, or something else, is a vital piece of processing capability for the continued production of mining operations across the globe. This paper highlights the success that Somerset has had in the coal industry worldwide as well as the initial successes with phosphate, iron ore, and copper tailings (patent pending).

Mar 2, 2022

By Hugh W. Evans

Many reports and papers have been delivered on projects under construction or already in operation, but we believe there are few that have been written about projects yet to be built specifically dealing with advanced mine and environmental planning. This paper describes such planning for Atlantic Richfield Company's Black Thunder mine. Project planning is a cyclic phenomenom involving four broadly overlapping planning steps (Figure 1). The demands of the public include needs that can be satisfied through planned resource development. Using a base of information that partly exists and must in part be gathered and updated, the preplanned development can be, evaluated. The evaluation process, with built-in environmental constraints leads to an implementation procedure. Implementation results in the development, including the release of the affected area to other public demands that follow.

Jan 1, 1975

By J. Sottile, V. Androulakis

Operators of underground coal mine shuttle cars are exposed to numerous hazards including noise, dust and musculoskeletal trauma. The repetitive nature of shuttle car operation leads to fatigue-related incidents and soft tissue injuries. The poor visibility conditions, and dust and noise increase the occupational hazards to the operator, as well to other miners. To reduce the risks for all miners, towards providing a safer working environment for all workers, the introduction of autonomous shuttle cars is essential. This paper introduces a project to demonstrate the feasibility of incorporating autonomous shuttle cars in the underground coal mining cycle. The autonomous shuttle car will be able to localize itself, to map its surroundings and to navigate in an underground GPS-denied environment. It will also navigate efficiently by fusing different on-board sensor modalities, autonomously planning the optimum path and traversing around the mine while avoiding collisions with humans and other static and dynamic obstacles. This will be achieved by exploring and testing different state-of-the-art techniques and off-the-shelf components, and integrating them into existing equipment, i.e., retrofitting an actual shuttle car. Moreover, a modified mining system will be demonstrated which will incorporate the autonomous shuttle car, capable of making real-time decisions, into the mining cycle. The system will regulate the interactions between the autonomous machinery and the human dynamic, with emphasis given to the safety of the workers, and enable the real-time, remote supervision of the mining process. The focus will be on coal mines, where the room and pillar mining method is used. INTRODUCTION The growing demand for mineral supplies combined with the steady decline in the available surface reserves has driven the mining industry to mine deeper underground deposits. These deposits are difficult to access, and the environment may be hazardous to mine personnel (e.g., increased heat, difficult ventilation conditions, etc.). Moreover, current mining methods expose the miners to numerous occupational hazards such as working in the proximity of heavy mining equipment, possible roof falls, as well as noise and dust. In recent decades, the utilization of autonomous machines has evolved in the mining industry to provide increased health and safety to mine personnel and reduce their exposure to adverse conditions. Automation aims to remove the workers from the hazardous conditions which may be present in an active mining area and place them to a more comfortable and safer environment at a distance from the active mining face. Examples of incorporation of autonomous machinery in the mining industry include the fleet of more than 100 autonomous mine trucks that are employed at the Rio Tinto’s iron ore mines in Western Australia for material haulage. There are also semi-autonomous, teleoperated LHD machines employed at several mines around the world (e.g., Sweden, USA, China). However, the operation of the autonomous machinery in these cases is either partial (semi-autonomous, teleoperated vehicles) and of small-scale or occurs at surface mines where GPS significantly facilitates the autonomous navigation of them.

Jan 1, 2019

By N. Vayenas

Modern mines possess a wide variety of capital intensive equipment. Equipment failures and the associated down time contribute significantly to the overall maintenance, operating and production costs of a mine. Reliability investigations are becoming a standard practice, as the equipment becomes more complicated and the effective use of resources is critical for achieving higher productivity and mine safety. In view of the recent global initiative for sustainable development in the mineral industries, reliability of capital intensive machinery should be considered as a key indicator for sustainable development and growth. This paper discusses the application of equipment reliability as a sustainability indicator and proposes a methodology for its practical use. Reliability of equipment systems is useful for product life cycle assessment, mine performance measurement and evaluation.

Jan 1, 2007

By SHANTAE LEE, ELAHEH TALEBI, Frank A. Drews, W. Pratt Rogers

Fatigue in mining operations is a serious issue and a significant contributor to incidents and accidents. While mine operators are using or introducing new technology to monitor operator fatigue, there is little work that focuses on the subjective experience of fatigue and the use of fatigue monitoring technology. To investigate this issue, eight focus groups with a total of 44 operators of heavy haulage equipment working for two mining companies in the Mountain West of the USA participated in 1-h focus groups. The topic of the focus groups was the experience of operator fatigue and issues surrounding fatigue at the workplace. The results of the content analyses suggest that operators are well aware of the signs of fatigue, and that they understand the severity of these signs as well. In addition, they are aware of the effect of fatigue on driving performance and are using a wide range of methods to manage fatigue. Finally, based on participants’ assessment, current fatigue monitoring systems lack face validity and reliability and are perceived as not being effective. The results of this study emphasize the importance of a socio-technical systems perspective in the context of miner health and safety management. Only such a comprehensive perspective can result in improvements that are sustainable.

Jun 17, 2020

By Jan K. Wolski

The PC computer program PCVENT, version 3.3, for the ventilation network analysis now incorporates a real-time fire simulator. Position of the fire or a source of contamination and the character of the event are input from the keyboard. There are several options of type of fire: heat only, contaminant only, or both with a constant burning rate or with oxygen as the only limiting factor. Airway resistances or fan characteristics can be modified during a fire simulation. This allows testing of various fire suppression strategies. Program application in the analysis of a real mine fire is presented.

Jan 1, 1991

By Nathan Painter, Kevin Andrews, Andrew Karpa

Groundwater flow in bedrock units is an important factor to be considered for most mining situations, both underground and open pit excavations. Characterization of the hydrogeologic system into which a mine will advance is an important factor for slope and entry stability, mine dewatering design, and potential environmental considerations including stream loss and water well damage. In addition, hydrogeologic characterization of bedrock is important for locating water wells and for groundwater contamination mitigation. Hydrogeologic characterization for a site begins with a desktop study and often evolves to include drilling, geologic logging, monitoring well installation, groundwater sampling, pump testing, and packer (Lugeon) testing. In addition to these methods of hydrogeologic data collection, downhole geophysical logging of exploration and monitoring well boreholes provides detailed information associated specifically with in-situ conditions of each hole. The basic suite of geophysical logging tools used for hydrogeologic characterization often includes Optical or Acoustic Televiewer (O/ATV), full wave sonic, gamma-density, fluid temperature, resistivity, specific conductance, and flowmeter. For many hydrogeologic settings, groundwater flow in the bedrock is dominated by discontinuities, or fractures, in the rock. O/ATV logging allows for determination of the frequency (clustering), orientation, and aperture width of in-situ fractures, while sonic logging allows for estimation of intact rock strength. Fluid temperature logging and flowmeter measurements provide insight with regard to potential groundwater inflow zones, and other tools provide information for geologic unit contacts. This paper outlines the process and benefits of using downhole geophysical logging for hydrogeologic characterization and provides generalized examples from industry experience.

By Manoj Kumar, Anil Kumar Singh, Prabal Patra, Ashish Agrawal, Souvik Ghosh, Subhashis Kundu, Kamma Ramakrishna Rao, Manish Kumar Gupta, Anindya Sarkar

The slag measurement systems in the cast house are very important. In the conventional method, the slag is granulated in a slag granulation system, and the slag flow rate is measured by the associated belt scale. However, in places where a slag granulation system is not available, the alternate approach is to deduce a theoretical calculation and develop the measurement because the commissioning of such slag granulation requires huge capital and has inherent geographical limitation. However, the theoretical approach suffers from several drifts and is far from the reality. In the present paper, we have innovatively engineered a sensor by designing the stellite-coated thermocouple that can measure the temperature of the slurry and placed it in such a way that the abrasive slag granules do not obstruct it, but we could measure the temperature of hot water, and further based on the thermodynamic approach, the slag flow rate is determined that can be compared with the theoretical approach. This approach of slag rate measurement is cost-effective and long-lasting.

Oct 2, 2023

By HONGWEI YANG, Lili Zhang

The oxidation behavior of copper smelting slag under non-isothermal conditions was studied by thermal analysis. The results indicate that the copper slag is mainly composed of fayalite ( Fe2SiO4) and magnetite ( Fe3O4). The oxidation behavior can be divided into two reaction stages with the increase in temperature; the first stage is the oxidation of fayalite to magnetite, and the second stage is the oxidation of magnetite to hematite. The two reaction stages cannot be strictly separated; that is, the reaction of fayalite is not complete, and magnetite has begun to transform into hematite. Based on the TG (thermogravimetric) curves, the ABS (Achar–Brindley–Sharp–Wendworth) differential and the Coats–Redfern integral methods were employed to investigate the oxidation kinetics of copper slag during the continuous heating process. The oxidation of fayalite into magnetite and amorphous silica phases occurs mainly in the temperature range of 673 to 1083 K. The activation energies calculated by the two methods are 193.69 and 195.52 kJ mol− 1, respectively. The reaction is consistent with Avrami–Erofeev equation, and the mechanism of oxidation is random nucleation and growth. The oxidation of magnetite to hematite occurs at 1083–1303 K. The activation energies are 308.79 and 328.77 kJ mol− 1, respectively. The mechanism conforms to the Jander equation and is controlled by the two-dimensional diffusion.

May 16, 2022

By Hossein Ghaedi, Hadi Fattahi

Despite the significant role of coal in the economic progress of nations, the occupational and health risks associated with its mining pose a major concern for industry stakeholders. The occurrence of roof collapses in coal mines remains a critical factor leading to substantial loss of life and financial damages for miners. Therefore, accurately predicting the roof fall rate (RFR) holds paramount importance. However, the uncertainty surrounding rock parameters in mines hinders the application of conventional methods to assess roof collapse rates in coal mines. To tackle the challenges associated with predicting roof fall rates in underground coal mines, this study proposes a novel solution by leveraging the Rock Engineering System (RES) method. The investigation is grounded in a dataset comprising 109 data points, encompassing crucial input parameters like depth of cover (DOF), primary roof support (PRSUP), intersection diagonal span (IS), mining height (MH), and coal mine roof rating (CMRR). In the model construction phase, 80% of the data (87 points) were utilized to build the RES model. A critical aspect of this study involves the evaluation of the RES model’s performance against alternative regression techniques, namely linear, power, exponential, polynomial, and logarithmic regression. This comparison was executed using the remaining 24 data points (20% of the dataset) for rigorous evaluation. Employing key statistical metrics such as mean square error (MSE), root mean square error (RMSE), and squared correlation coefficient (R2), the study systematically demonstrated the superior accuracy of the RES-based method compared to other approaches. In conclusion, the outcomes strongly support the efficacy of the RES method in predicting roof fall rates, not only in the specific case studied but also indicating promise for its application in other underground coal projects. This underscores the potential of the RES method as a reliable and versatile tool for forecasting roof fall rates in the complex and critical context of underground coal mining.

Mar 19, 2024

By J. Y. Hwang

Alunite has been utilized as raw materials for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores include quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 microns. Adequate separation techniques for such fine particles have not been developed. A new method for the beneficiation of alunite ore is proposed in this study. 'Ibis method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g. an alunite concentrate of 90% grade with 80% recovery, has been obtained from an Utah ore. Techniques for the selective co-flocculation of magnetite and quartz, the separation of the carried quartz, and the recovery of magnetite after separation are discussed.

Jan 1, 1985

By Richard J. Lundin

Literature research is an inexpensive, yet effective tool for the direct discovery of ore deposits. Case studies abundantly demonstrate that properties with viable mineralization and *proven reserves have been overlooked, forgotten. or ignored and can be rediscovered by inexpensive literature search techniques Areal studies s as WaIlaby Enterprises Mining District Data Base Program appear to be more effective than traditional commodity studies. The success of such studies depends on the inclusion of Mineral Clairant Questionnaire Data, Mineral Ownership Data, Field Examination Data and the continual updating of all information. Such studies are valuable for proposed or existing Wilderness Area Evaluations.

Jan 1, 1977

By J. J. Sense

The Mission Unit of American Smelting and 'Refining Company is located in Pima County, Arizona, approximately twenty miles southwest of the City of Tucson. The Unit consists of an open pit copper mine and concentrator. The concentrate is shipped by rail to Company Smelters at Hayden, Arizona, or El Paso, Texas Mine stripping began at Mission in the fall of 1959, and construction of the 15,000 tons per day concentrator gas started in the spring of 1960, The first ore was treated in mid summer of 1961 and full ore production was reached in August of 1961. At that time over 46,000,000 tons of material had been moved from the pit. Current production (ore and waste) averages over 100,000 tons per day. Total production to date (ore and waste) over 120,000,000 tons.

Jan 1, 1964