Search Documents

By Dieter Loh, Mathias Knoll, Florian Werres

When a new tunnelling project starts, it has been a vital tradition for decades to cast and erect master rings horizontally on a flat surface to demonstrate the compliance with dimensional tolerances. Some tenders ask for the erection of two or even three rings upon each other or repeated master ring erections at intervals throughout the project. Especially for large diameters, this is a challenging and risky task for the workforce in the segment factory. A truck-mounted crane is often necessary, and in some cases it can take up to a week to complete a master ring. The concept of virtual rings has the potential to replace this tradition by assembling master rings digitally instead of physically. This is based on a best-fit approach, considering the 3D coordinates from laser tracker measurements of segments or segment moulds. Building a virtual ring, a sub-millimeter accuracy can be achieved, the alignment of neighboring circumferential and ring joints observed, and the fit of bolt holes checked. The traditional method, on the other hand, is discussed controversially despite the significant amount of work and risks—particularly as the horizontal position of the ring and absence of gaskets do not simulate the reality in the excavated tunnel. This paper will highlight the technical aspects of virtual rings, as well as their pros and cons, illustrated by a case study from London Thames Tideway where a total of 30 physical master rings could be replaced by virtual rings.

Jun 13, 2023

By Donald M. Ulbrich

Any of you who served in the military remember the admoniton to "get the lead out," In the military environment, where cost wasn't always a factor, "get the lead out" was more often a call for activity of any sort than activity of a particularly productive nature. As a result, when the top sergeant yelled "get the lead out," lots of people started moving.. . usually to get out of his way. Now there's a new cry, ..one that comes not only from the military but from an entire nation threatened with dependence on foreign sources for its energy needs. That cry ...get the coal out, Like the earlier order, it's a call to activity. A signal that the coal reserves of the United States must be tapped so that Project Independence can succeed by 1985, But it's more than a mere call to activity; it's also a call to achieve productivity. ,a call to produce coal both efficiently and acceptably. And that leads us to the key questions of where the coal is going to come from to meet that 1985 goal, and how can it best be mined. Where will the coal come from? There's no doubt much of it must come from surface mining in the West. How can this coal be mined? There are several options available but there is an excellent case to be made for using mining shovels and haul trucks due to their versatility in stripping, loading and reclamation, We'll explore this approach in this talk today.

Jan 1, 1976

By G. K. Hoffman

Humate, defined as weathered coal or mud-stone rich in humic acid (HA) and fulvic acid (FA) have been mined, primarily as soil amendments or drilling mud additives, in New Mexico for 15-20 years. The New Mexico humate resource is estimated to be 11 Gt, including weathered coal and organic mudstone. The HA and FA content determines the end-use, therefore a simple and consistent method of measuring organic-acid content was developed. The New Mexico Bureau of Mines and Mineral Resources method is based on repeated alkali leaching and acid precipitation. Precipitates of humate are ashed, with mass balance of solids maintained, to correct for material added during alkali-acid treatment. Analyses of upper coal member, Cleary Coal Member (Menefee Formation) and Fruitland Formation samples from the southeast San Juan Basin show ashing to be important in accurate analysis of FA content. Ash in the total FA fraction averages 70% compared to 2% in HA. The FA in weathered coal and organic mudstone are similar, although HA is significantly higher in the former. As weathering progresses, the FA content of weathered coal increases faster than in organic mudstone because of the greater total organic material in coal.

Jan 1, 1994

Power cable costs are only a small part of total mining costs. So many mine operators consider power cable failure and resultant downtime as part of the cost of doing business. But, viewed in terms of lost production, these costs can be quite significant. Now one company, Cablec, seeks to cut cable costs by upgrading the polymer compounding process used to make cable insulating and semiconducting materials. Cablec is the leading manufacturer of electrical power cables in North America. And with about a third of the market, Cablec is the largest supplier of power cable to the mining industry in the United States. To improve its products, Cable has entered the polymer compounding business. In July, it began producing insulator and semiconductor polymer compounds at its plant in Indianapolis, IN. "This new facility provides a quantum leap over conventional compounding methods," said Harry C. Schell, Cablec's president and chief executive officer. "The Cablec polymers plant is producing a dramatically higher standard of polymer compounds that provide significantly higher levels of performance and improved life cycle costs for power cable." Cablec faces tough foreign competition in the wire and cable business. Competing on price alone is difficult, particularly when foreign producers are state subsidized. So Cablec feels the best way to compete is to establish new quality production standards. The company's new polymers plant is one way to do this. By increasing purity control and uniformity in polymer compounding, Cablec says its power cables will last longer and fail less often. A typical medium voltage cable consists of a conductor, conductor shield, insulation, insulation shield, metal shield, and jacket. The conductor shield and the insulation shield are conducting polymers. Contaminants and imperfections can occur within the insulation, at the conductor shield/insulation interface, or at the insulation shield/ insulation interface. Over time, these contaminants and imperfections can decrease the electrical strength of the cable or cause premature cable failure. The effort to minimize the number and size of any possible contaminants begins with pure polymer compounds mixed in a clean facility. However, most power cable manufacturers manually handle raw materials, use ethylene/propylene (EP) in bulk bales, and mix polymercompounds in open Banbury mixers. The quality and uniformity of polymer compounds is also impacted by temperature variations in the mixing process. This results in wide gradations of product consistency from batch to batch and ultimately contributes to power cable failure. Cablec says the improved polymer compounds from its state-of-the-art plant will be the purest and most consistent insulating and semiconducting materials available. The plant itself RCA spent $18 million to build Cablec's Indianapolis plant. RCA used the facility to mix specialty polymer compounds used to make video disks. RCA had two considerations in mind for the plant, cleanliness and uniformity of the compounds. However, when the video disk market failed to materialize, RCA sold the 46.5 dam 2 (50,000 sq ft) plant to Cablec for $3.1 million. Cablec invested an additional $3 million for modifications and increased production capabilities. Today's replacement cost for such a facility is estimated at $30 million. Cablec says the plant will set a new standard for performance and be economically difficult to duplicate anywhere. One of the essential elements of the plant's clean process environment is the air intake system. It filters contaminants greater than 2 um, less than one-fiftieth the current industry standard. All material handling and conveying areas in the facility are air-locked. This keeps out contaminants such as smoke, dust, and pollen. Banks of pneumatic pumps move polymer components through the system and continually filter the air. The plant also has a backup air intake system. No process downtime due to pump failure here. From the time raw material enters the plant, it is stored, transported, and processed in filtered air by an airtight stainless steel system. The stainless steel resists rust and corrosion. This further eliminates the danger of contamination from paint or rust particles in the conveyance network. A computer system allows a single operator in a central control room to monitor every aspect of the compounding process from air quality to line speed. The computer

Jan 12, 1988

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By Richard H. Olson

Talc is currently mined in the U.S. in six major districts. The size and depth of the ore bodies and their mineralogy dictate the types of products manufactured and the mining and processing methods which must be employed. The geology of the major deposits is well known and will be but briefly discussed The major emphasis will be placed upon the past history of the districts, the size and depth and configurations of the ore bodies, the ore mineralogy, and how all of these factors govern the types of mining and processing operations which may be employed in each of the districts.

Jan 1, 1984

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal, and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely. In this study, the failure energy partitioning of Nugget Sandstone specimens is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrate a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining-induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

Jul 1, 2020

By R. Bryce, T. J. Doughty, K. Stoll

Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Ca6Al2(SO4)3(OH)12•26H2O Ettringite readily precipitates in high pH water and by doing so, removes sulfate from impacted waters. The SAVMIN process, piloted in South Africa, is one method to produce ettringite. In this process, aluminum hydroxide is the aluminum source. The Cost Effective Sulfate Removal (CESR) process is similar to SAVMIN, but uses a proprietary aluminum source instead of aluminum hydroxide. Outotec and Veolia also have their own versions of the process using their specialized process equipment. TWC patented a version of ettringite precipitation using metallic aluminum as the aluminum source for ettringite formation. The benefit of using aluminum metal is that no additional ions are added to the process. At high pH, the raw aluminum corrodes in water causing hydrogen gas generation as the water is chemically reduced. This reaction is shown below:

Jan 1, 2019

By R. Kealey, D. Huo, Q. Zhang, Y. A. Sari

Greenhouse gas (GHG) emissions from primary mineral and metal production account for ~10% of global GHG emissions. One of the main sources of GHG emissions in mining operations is fuel consumption by haul trucks. Given their size and carrying capacity, the fuel consumption of haul trucks can approach 250 liters per hour. An average of 30% of the idle time of the trucks is spent while waiting in the queue. Inefficient truck dispatch planning can waste resources, cause dilution and elevate GHG emissions. In this research, a machine learning based truck dispatch approach was developed to dynamically route the haul trucks based on the loaded material, the road traffic, the estimated wait time, and the maintenance needs of the trucks. The GHG reduction potential of this smart fleet management approach was estimated by calculating and comparing the related carbon emissions versus scenarios using traditional fleet allocation approaches. Results suggest that this dynamic fleet allocation approach can significantly reduce GHG emissions at mineral production sites by optimizing waiting times and the overall distance travelled while achieving the same production levels.

Mar 2, 2022

By Nicholas C. Lias

Quartz crystals are the raw material from which are made the crystal units utilized in filters and oscillators so vital to the performance of all long distance communications systems. These devices act as the heart of equipment that permits a single telephone cable to carry hundreds of conversations simultaneously. Quartz crystals are of value in communications because of this piezoelectric nature, that is when an electric signal is applied to the quartz, there is a resulting mechanical motion and conversely, a mechanical stress results in an electrical output signal. A plate cut from a quartz crystal will oscillate at some specific frequency, which is determined by the physical dimension of the plate. During the early stages of telephony, all quartz plates were cut from natural quartz, which was imported mainly from Brazil. Since the source of this important raw material was based upon a foreign supply which is located at a great distance from the user and could be vulnerable in time of a national emergent, it became necessary to maintain a large inventory of this strategic material. Also due to the considerable cost of natural crystals of a size and quality suitable for Bell System use, an investigation was made by Bell Laboratories into the possibility of developing a substitute material. The effort was successful and led to a joint development program between Bell Laboratories and Western Electric. This program brought about the design of manufacturing facilities capable of producing large quantities of cultured quartz at Western's Merrimack Valley Works, No. Andover, Massachusetts.

Jan 1, 1973

By G. G. Marino, J. W. Mahar

This paper provides an utierstanding of the betivior and potenttil damage of homes resulting from sag-type mine subsidence. This is done with extemive research of numerom case histories in Illinois collected by the authors. The howe response to substience-itiuced ground displacements are summarized and evaluuted. A damage level criteriu, specifically developed for residenttil structures, is presented based primarily on repair costs. Damage levels and the associated subsidence profile characteristics for each case history are compared.

Jan 9, 1985

By Gennaro G. Marino

This paper summarizes and evaluates data on mine subsidence ground movements and associated damage for houses in Illinois. Based on the data collected, the response of homes to subsidence ground movements is expressed in terms of repair costs. A damage criteria is then proposed that relates the ground movements and damage levels. The data were collected as part of a comprehen¬sive study performed for the Illinois Abandoned ?Lined Lands Reclamation Council, A -M-RC, by the Civil Engineering Department at the University of Illinois, and probably will be published in late 1934 by the council. The study concentrated its efforts on surface ground movements and the effects to houses over abandoned room and pillar mines. The resultant surface subsidences are commonly dish or bowl shaped and are termed sags. Method of Analysis The steps in analysis used to arrive at the proposed damage criteria are: 1. Canvas and rap subsidence damage in houses, 2. Assess the associated ground movements, 3. Estimate the damage repair cost, 4. Develop a damage/repair level classifica¬tion, 5. Correlate the associated ground movement, damage/repair level and home construction type, 6. Propose a damage criteria.

Jan 1, 1984

By Kenneth Savidge

With the recent demand for increased coal production there has been a corresponding increase in the horsepower of the shearing machines. The resultant increase in the machine haulage pull has heightened the incident of haulage chain breakage resulting in machine downtime, but more seriously the danger to face personnel. This paper discusses the application of chainless haulage to longwall mining and describes the systems currently available.

Jan 1, 1978

By S. C. Termes

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble crosslinked starch xanthate (ISX). ISX is insoluble, has a shelf life of over a year when kept cold, and has a higher molecular weight due to cross linking than the soluble noncrosslinked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines but not silicious gangue. Floc formation, floc size, and settling rate are strongly dependent on pH, with the pH dependence differing for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1982

By James W. Estep

The sulphur shortage that has occurred in the past two years has directed attention more and more toward sour natural gas reserves, Wellhead values of sour gas vary widely depending upon the acid gas composition, location, market conditions, and necessary processing charges. Preparation of a saleable residue gas is considerably more involved and expensive than that normally encountered in treating a sweet gas. Recent revisions in sales gas specifications have increased capital costs and processing charges. The presence of hydrogen sulphide and carbon dioxide in a natural gas contributes to shrinkage factors that may approach 50%. Fuel required by the gas sweetening process and sulphur slant tail gas incineration also contributes to a further reduction in the volume of residue gas available for sale. The additional processing facilities involving gas sweetening, mercaptan removal, expanded utilities, sulphur recovery and sulphur handling, all demand additional operating and maintenance staff. A favorable sulphur market under certain conditions may justify the processing of sour gas whereby sulphur is either a by-product or a co-product, Five typical cases involving different compositions of sour gas are presented for evaluation. Capital costs, operating problems, and operating costs are presented in detail for full economic evaluation

Jan 1, 1967

By W. W. Atkinson

This paper describes some concepts developed in a geologic data recording system at the Victoria, Nevada breccia pipe-skarn copper mine. The recording system is not fundamentally new, but represents expansion of earlier ideas. The paper is based on the philosophy that a high quality geologic data base is necessary and that it should be complete, clear, standardized, neat, quantitative, and readily useable. It may be multi-colored or simply black and white. Graphic, descriptive and quantitative recording of data is essential. A format for core logging is presented and discussed and as well as a multiple overlay system for recording data gathered in surface mapping.

Jan 1, 1983

By G. H. Gronhovd

The U.S. Geological Survey estimate of the total remaining reserves of lignite in this country as of Jan. 1, 1967 was about 448 billion tons. This represents 27 percent of the total coal reserves on a tonnage basis and about 17 percent on a thermal basis. Approximately 98 percent of these reserves are in a vast lignite field located in western North Dakota and eastern Montana. This field also extends north into the Canadian province of Saskatchewan. Despite these large reserves and relative ease of mining by stripping operations, lignite production historically has accounted for less than 1 percent of the national total. This is largely due to the fact that the lignite deposits are located in an area that has no large centers of population and the economical radius of transportation is limited by its relatively high moisture and low heating value. Commercial utilization of North Dakota lignite for power production became firmly established in the mid-1920's with the development of the first successful lignite-burning equipment. Most of the early lignite-fired boilers were equipped with spreader stokers, but as the size of the plants increased, pulverized-coal firing became the more popular method, and with few exceptions, the plants built during the past 15 years are pc-fired.

Jan 1, 1968

By Kevin A. Foo, Murray D. Bath, John H. Canterford, Arnaldo Ismay

There is no doubt that the dominant future source of gold will be the so-called refractory ores, especially those with gold in a pyrite/arsenopyrite matrix. Minproc Engineers is taking an active role in establishing detailed design criteria for a number of apparently competing processes. This involves generating a detailed understanding of the metallurgy involved, systematic pilot plant testing, and the application of advanced engineering technologies. This presentation outlines the approach adopted by Minproc as well as the design criteria for several current projects.

Jan 1, 1989

By J. H. Meza Viveros

This paper describes some actual parameters and technologies used at Mexicana de Cobre Smelter, and the principal design parameters and new technologies which wiil be used with the smelter expansion project, in order to increase the production capacity of anode copper from 180 000 mtpy to 300 000 mtpy. Likewise its describe some parallel projects under construction also in the smelter plant.

Jan 1, 1997

By Kadri Dagdelen

New underground coal mines have become increasingly expensive to open. A simple drift mine producing a raw coal product can cost as much as $50 million while a new shaft mine producing a washed coal product can cost up to $200 million. As a result, few if any speculative new mines are constructed. Normally, a long term coal supply agreement is needed to justify new mine projects. Negotiating a supply agreement prior to production start is difficult. Pricing must be based on estimated rather than historic costs and coal quality must be estimated from core hole samples versus actual shipments. Further in todays competitive coal markets, there is little margin for error in either price or quality.

Jan 1, 1983