Search Documents

By Desiree Willis

At 6 percent downgrade to a low point beneath California?s Sacramento River, the Lower Northwest Interceptor Sewer was a difficult project from the outset. Project owner Sacramento County Regional Sanitation District (SRC-SD) planned to excavate the V-shaped tunnel in two sections using an earth pressure balance (EPB) machine in soft ground. Muck removal, due to the steep downgrade, was a tricky proposition. ?We did look at muck cars, but determined they were not the best option due to the relatively steep slope of the tunnel alignment. The safety benefits of conveyors on this job were obvious, as there were not the potential hazards associated with muck cars traveling on an incline or derailing,? said Steve Norris, senior civil engineer for SRCSD The successful project represented one of the first instances of a conveyor system being used for a soft ground tunnel boring machine (TBM) application. Several projects in California, including a recent tunnel completed in 2009, have highlighted a growing acceptance of conveyor muck removal in a variety of ground conditions. Conveyors offer higher system availability than more common methods, such as muck cars, as they allow for continual operation of the TBM. The design of conveyor systems must, however, take into account the differences in material between soft ground and hard rock, including belt cleaning features, sealed transfer points and other elements.

Jun 1, 2010

By Harald F. Solberg

A preliminary study of the performance of a 4-inch Krebs cyclone at near rope conditions and different feed slurry temperatures was completed. Results suggest that temperature influences the x50c size which, in turn, did not depend upon spigot diameter. The bypass correction to a reduced efficiency equation incorporating the concept of a critical size xo was a function of fractional water recovery to underflow and may depend on feed size and feed percent solids. Further experimentation is required to develop an accurate model at near rope conditions.

Jan 1, 1981

By T. Payne

Underground heat issues are mainly focused on the detrimental effects to a workers health. However, working in hot, humid conditions has other negative effects. Studies have shown that safety, productivity, workforce morale and operating cost are also worsened in these conditions. The human body has several mechanisms for rejecting heat and remaining cool. However, once the air temperature exceeds about 34°C, the only effective mechanism is by evaporation of sweat from the skin. This is assisted by acclimatisation which is the human body?s enhanced ability to combat extended exposure to heat. The body has to remain well hydrated when working in heat as even small degrees of dehydration cause significant decreases in the ability to work in heat. There are two ways in which heat load can be reduced: Through use of refrigeration/vent/cooling to reduce thermal stress on workers; Reduce the contribution that heat sources have to underground heat load (e.g. reduce idle time, fleet size, etc). Some of the sources of underground heat have the potential to be more manageable than others. Geothermal heat and heat from autocompression will be found in all mining situations in varying degrees depending on geothermal gradient and surface temperature, however, the use of equipment and blasting may be streamlined to reduce the underground heat load. It is through a combination of the available options that most mines will successfully control their heat related problems. Mt Isa, which has been a focus for heat related study in Australia, has successfully implemented protocols for working in heat. Through combining these with the installation of a surface bulk air cooling plant, Mt Isa has consistently reduced the incidence of heat illness. This is likely to be the most cost effective method of reducing heat load for deep mines in Australia. Shallower mines which may only occasionally encounter hot conditions should consider more portable cooling options. This study will review the heat issues in underground Australian metalliferous mines.

Jan 1, 2009

By M. J. Gula

In the solvent extraction -electrowinning recovery of copper from oxide or sulfide ores there is a continuous transfer of iron and other impurities from the primary leach solution to the copper electrowinning electrolyte via chemical transfer or mechanical entrainment. Iron is the principal impurity that has to be controlled in the electrolyte by a "bleeding" of the electrowinning solution. This bleeding transfers copper and sulfuric acid back to the primary leach circuit along with the iron. Copper is recovered via the solvent extraction process and generally the sulfuric acid is used as a reagent in leaching. Unfortunately, cobalt, which is added to the electrowinning solution to modify the anodic process, is irreversibly lost through the bleeding operation. This cobalt loss represents a significant operating cost to SX-EW copper producers. DiphonixTM ion exchange resin contains diphosphonic acid and sulfonic acid functional groups on a polystyrene-divinyl benzene matrix. This resin has been found to strongly and selectively extract ferric ion from copper sulfate -sulfuric acid solutions containing cobalt. Thus, an ion exchange process using DiphonixTM resin for the control of iron has been developed to replace the conventional bleed stream process. The new process minimizes the loss of cobalt from the electrowinning circuit and strips the iron into a sulfate based solution suitable for leach solution makeup. In addition, this process can effect a lowering of the total iron concentration in the electrolyte circuit with an associated increase in current efficiency. In this paper, data on the loading and elution of iron are presented. Laboratory and pilot scale data will be discussed along with information on process design and comparative economics.

Jan 1, 1996

By Marcos de Paiva Bueno, Leonardo Ribeiro Lara, Rajiv Chandramohan, Thiago de Almeida, Greg Lane

This paper explores the impact of the significant difference between the number of geochemical assays conducted for grade estimation and the number of comminution tests performed for throughput and performance forecasting. Both grade and throughput are key factors in determining the project. We analysed 154 feasibility study reports to assess the impact of sample frequency for comminution test work on project revenue. This disparity in size between assay and comminution data arises because geological and resource-grade risks cannot be managed without extensive geochemical testing, whereas comminution risks are traditionally mitigated through design methods and the use of contingencies. This approach is partly due to the relatively high cost and large sample requirements associated with traditional comminution tests. Our analysis demonstrates that insufficient comminution sampling and testing leads to uncertainties in throughput forecasts, creating significant financial risks. Data from the feasibility studies show that a 1% change in mill throughput can result in up to a 5% variation in Net Present Value (NPV), underscoring the sensitivity of project economics to operational performance. Building on previous work, we reference studies that reveal how low frequency of comminution testing can increase uncertainty in mill throughput forecasts and increase financial risks. We propose an approach that optimises the number of comminution samples tested to enhance forecast accuracy and reduce NPV variance. By adopting this approach, mining projects can improve financial reliability and mitigate risks associated with underperformance in SAG and AG mill-based operations.

Feb 1, 2025

By R. Gorakhki, R. Stafford, A. Jung

Geosynthetic clay liners (GCLs) have been used widely as an alternative for compacted clay liners and covers in mine waste applications. The high swelling of bentonite particles in the GCL creates a uniform barrier layer that results in low permeability of water and mine waste leachate. GCLs must provide sufficient internal and interface shear strength stability, especially if GCLs are used in steep slopes under high normal loads. Peel strength is a common parameter that is typically correlated to internal shear strength properties of GCLs. The relationship between internal shear strength and peel strength of GCL at normal stresses of 287, 575, 862, and 1724 kPa is evaluated in this study. The data in this study was compared with the peel strength-internal shear strength relationships found in literature. The study concludes that the relationship between peel strength and internal shear strength is unique based on manufacturing, needle-punching density and the method with and without heat treatment of the geotextile end fiber bundles.

Feb 1, 2023

By Joseph M. Chelini

The report shows the sensitivity that nine different cash-flow factors have on the discounted rate of return calculated from feasibiliity- studies on potenital open-pit orebodies of silver, copper, and uranium. Cash-flow factors of "grade", "market value", and "recovery" are. the most sensitive. This verifies the need of reliable estimates for these factors. The cost of evaluation of "preproduction cost" is the least sensitive. This gives credence to the fact that more consideration should be given to compiling sufficient data, as the largest financial losses are not in the cost of evaluation but rather in the abandonment of an unprofitable mining operation after a commitment of capital is made on the basis of an incomplete evaluation. Sensitivity analysis of cash-flow factors enhances evaluation programs by disciplining the collection of data and allowing more realistic distribution of evaluation monies.

Jan 1, 1971

By R. Mensah-Biney

The loading characteristics of gold-tetrabromide species onto activated carbon have been evaluated using a completely mixed batch reactor system. The overall loading of gold onto carbon was rapid for the first hour but continued slowly without cessation as a result of reduction of gold. Conventional equilibrium considerations were therefore not applicable. Although loading continued slowly after several days, abnormally high loading capacity values of 10-12 meq/g carbon (650-800 kgAu/tonne) could be attained within 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of [AuBr4l-onto the carbon surface where reduction to metallic gold took place. Elution of gold from the loaded carbon was feasible provided the carbon had not been loaded to too high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon is discussed.

Jan 1, 1992

By Ismail Adeniyi Okewale, Hendrik Grobler

Significant factors believed to be responsible for tailings dam failure which can lead to loss of lives, destruction of properties and assets or damage to the environment are the mechanics of material characteristics and static liquefaction. It is therefore essential to understand the tendency for the likely occurrence of liquefaction in tailings dam as well as mechanics behind the behaviour of this tailing materials (inevitable products of ore mining, mineral and metallurgical processes). This study aims to present the mechanical behaviour and susceptibility to liquefaction of a gold tailings sample. Series of oedometer tests were conducted to determine the compression behaviour and the possibility of transitional behaviour or not. Index and physical tests were conducted to determine engineering grading descriptors which was directly linked to compression behaviour and comparisons made with other tailings. Microstructure was studied to understand the effects of fabric on the behaviour of samples and the chemical composition and mineralogy were also investigated. The compression paths slowly converge and the gold tailings might be said to be less transitional. The gold tailing is less dependent on initial state. The loosest gold tailing is more susceptible to liquefaction and compared to other gold tailings, this sample is less susceptible to liquefaction.

Apr 19, 2024

By P. Zhang, W. D. Xiao

"A process mineralogy study was conducted to guide the development of a process for the extraction of vanadic oxide (V2O5) and aluminum compounds from bone coal and its ash as well as the production of byproducts. Results show that to extract the targeted metals at higher recovery rates, one must find a suitable agent capable of destroying the structure of the mica and breaking down the lattices in which these metal-bearing minerals occur. For such minerals, metal extraction efficiency is usually low if the approach is simply adding an oxidant that cannot destroy the structure. In this research, a byproduct fluosilicic acid (H2SiF6) at 20 percent concentration from an operating phosphate fertilizer plant was found to be powerful and effective for the leaching of vanadium-bearing minerals such as mica. This environmentally friendly process improved the leachability of valuable constituents in the bone coal significantly, with the leaching rate of V2O5 increased to 94 percent, from 83 percent, and that of aluminum oxide (Al2O3) increased to 75 percent, from 40 percent. X-ray diffraction and chemical analyses showed that the structure of mica can be destroyed using fluosilicic acid either alone or in combination with sulfuric acid. Based on the process mineralogy study, a processing flowsheet was tested, which resulted in a final V2O5 powder product with purity of 99.2 percent and an overall recovery rate of higher than 85 percent. The flowsheet consists of leaching, ion exchange and ammonium precipitation. With this process, various byproducts could also be generated, including aluminum fluoride, cryolite, aluminum sulfate, calcium sulfate, ammonium chloride, sodium chloride and cement admixtures.IntroductionVanadium is an important rare metal broadly used in the production of steel alloys and nonferrous alloys as well as in the chemical field as a catalyst. Vanadium-bearing bone coal and clays are abundant in China, and they contain other valuable metals such as aluminum. Bone coal is a type of carbonaceous shale. The vanadium-bearing minerals mainly exist in mica, kaolin, iron oxides, tourmaline and garnet. According to previous studies (Xiao, 2007; Xu, 1989; Xu and Chen, 1991; Ji and Xu, 1991; Chen and Xu, 1992; Xu and Heng, 1992), vanadium occurs from the isomorphous substitution of V3+ for Al3+ or Fe3 + in the crystal lattices of mica, tourmaline, garnet, dolomite and aluminosilicate minerals. In iron oxide and kaolin minerals, vanadium appears as an adsorption form. The isomorphous substitution of vanadium is more stable in tourmaline, garnet and silicate minerals. Therefore, vanadium in bone coal may exist in three phases: vanadium-containing kaolin and oxides, vanadium-containing mica, and tourmaline and garnet (Xu and Chen, 1993; Xu and Zhang, 1993; Xu and Wang, 1994; Feng, et al., 2005; Lin and Fan, 2001)."

Jan 1, 2015

By Hengwei Yan, Zhanwei Liu, Wenhui Ma, Ping Xiong

The sulfur in high-sulfur bauxite not only pollutes the environment but also harms alumina production. This study investigated the removal of sulfur from high-sulfur bauxite by adding Zn or ZnO during the Bayer process. The results showed that the different valence sulfur (S2−, S2O3 2−, SO3 2−, and SO4 2−) in sodium aluminate solution can be effectively removed by adding Zn during the digestion process. Adding ZnO removes the S2− in liquor, but the other sulfur compounds (S2O3 2−, SO3 2−, and SO4 2−) are not affected. The mechanism of sulfur removal has been elucidated, where the S2O3 2−, SO3 2−, and SO4 2− are first reduced to S2−, and after adding Zn, the S2− enters into red mud in the form of ZnS. The ZnO then reacts with S2− to generate the ZnS that enters into red mud. Thus, this is a new and effective method of sulfur removal by adding Zn during the digestion process. The results shed light on the removal of sulfur from high-sulfur bauxite during alumina production.

Jun 24, 2020

By Mark Van Dyke, Ted Klemetti, Joe Wickline

"The identification and mitigation of adverse geologic conditions are critical to the safety and productivity of underground coal mining operations. To anticipate and mitigate adverse geologic conditions, a formal method to evaluate geotechnical factors must be established. Each mine is unique and has its own separate approach for defining what an adverse geological condition consists of. The collection of geologic data is a first critical step to creating a geological database to map these hazards efficiently and effectively. Many considerations must be taken into account, such as lithology of immediate roof and floor strata, seam height, gas and oil wells, faults, depressions in the mine floor (water) and increases in floor elevation (gas), overburden, streams and horizontal stress directions, amongst many other factors.Once geologic data is collected, it can be refined and integrated into a database that can be used to develop maps showing the trend, orientation, and extent of the adverse geological conditions. This information, delivered in a timely manner, allows mining personnel to be proactive in mine planning and support implementations, ultimately reducing the impacts of these features. This paper covers geologic exploratory methods, data organization, and the value of collecting and interpreting geologic information in coal mines to enhance safety and production.The implementation of the methods described above have been proven effective in predicting and mitigating adverse geologic conditions in underground coal mining. Consistent re-evaluation of data collection methods, geologic interpretations, mapping procedures, and communication techniques ensures continuous improvement in the accuracy of predictions and mitigation of adverse geologic conditions. Providing a concise record of the work previously done to track geologic conditions at a mine will allow for the smoothest transition during employee turnover and transitions. With refinements and standardization of data collection methods, such as those described in this paper, along with improvement in technology, the evaluation of adverse geologic conditions will evolve and continue to improve the safety and productivity of underground coal mining."

Jan 1, 2019

By A. Hajati

The main purpose of this study was to find the optimum values for factors affecting the Zn recovery rate using oxine or dithizone as a chelating agent collector during flotation in a Hallimond tube. Eight control factors, including four levels of pH, oxine/dithizone, corn starch, sodium thiosulfate, sodium citrate, sodium silicate, conditioning and floating durations were considered in a Taguchi experimental design technique. An L32 orthogonal array was applied to determine the signal-to-noise (S/N) ratio. Analysis of variance (ANOVA) was used to determine the optimum conditions and the most significant parameters affecting the reaction rate. Analysis of the experiments using the Taguchi approach indicated that pH had the highest contribution to the recovery rate of zinc oxide particles. The results showed that the recovery rate of zinc increased by 43.4 ± 3.0% and 24.9 ± 3.2% using oxine and dithizone, respectively, under optimum conditions with a confidence level of 90%.

Jan 1, 2010

It was shown previously that chalcopyrite could be floated without using a collector when the ore samples were treated with small amounts of sodium sulfide (Na2S). The role of this reducing agent was considered to be one of a cleaning agent to remove the hydrophilic surface oxidation products. It was later found, however, that the collectorless flotation could be obtained only under slightly oxidizing conditions. This might suggest that collectorless flotation is not due to the clean surface but to the elemental sulfur which may be present as an incipient oxidation product. Therefore, a search for the presence of elemental sulfur has been made by means of ESCA, mass spectrometry, and solvent extraction followed by W spectrophotometric analysis. On the basis of these results, the mechanisms of collectorless flotation are discussed.

Jan 1, 1983

By Thomas L. Kesler

Lithium raw materials usable with present technology consist of pegmatite ore and surficial evaporite brine. Those advantageously located now supply world markets. Materials of similar grades and magnitude, but less favorably located, will come into production as present sources are depleted and markets expand. Some of these potential supplies have been explored, and are reserves in the sense of known availability and quality. Reserves herein are of two classes, those proved by close drilling and assaying, and those of only probable status because their scale and grade are unsystematically indicated. Possible resources include similar materials whose bulk can only be inferred on indirect evidence. All figures apply to total materials in the ground. No allowance is made for losses in mining, evaporation, beneficiation, or chemical processing.

Jan 1, 1977

By T. A. de Almeida, M. de Paiva Bueno, M. Powell

The mining industry is one of the foundations of modern society, providing not only the raw materials needed to maintain a contemporary lifestyle, but also serving as a basis for the development of future technologies. From the most basic components of an appliance to the materials needed to design an electric car or a space rocket, each raw material has gone through a painstaking procedure of extraction and processing, and ways to make this process more efficient will be of great help to meet an ever-increasing demand for minerals. One of the biggest challenges when extracting mineral resources is to measure the variability of the mineral body prior to processing. Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this paper is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

Feb 1, 2023

By Thomas R. Hightower

The Thunderbird plant was erected in Sullivan County in Indiana during 1958-1959. It was first put in operation in March of 1959. At the present time the source of the raw coal is from the Indiana No. 6 seam. The underground operation at present consists of two continuous mining units and two conventional units. The underground is all belt haulage and the first unit with which this paper is concerned is the slope belt. It is a 48-inch-wide inclined belt with 980-foot centers and a lift of 275 feet. The belt is powered with a 350 H, P, motor and has a rated capacity of 600 Tons per Hour. The belt is equipped with a Merrick Scale Company Weightometer, The raw coal moves from the belt to a 6'x12' extra heavy Allis-Chalmers Ripl-Flo equipped with 6" round-hole screens. The over product of the screen is fed into a 10'x20' long McNally- Pittsburg rotary breaker equipped with 4-l/2" round-hole screens. The oversize rock is discharged into a bin that is emptied with a refuse truck. The through-product of the breaker, along with the through-product of the Ripl-Flo, passes either directly to the McNally Giant washbox or to a 36" belt that transports it to a 1000-ton storage bin,' The change from either to the washbox or to the storage bin is made by use of a motorized gate controlled by the plant operator,

Jan 1, 1961

By P. W. Erickson

Development of the Twin Buttes mine entailed the largest known preproduction stripping job in the history of mining. It linked earthmovers and conveyor belts in a new approach to development of a pit that may reach, or even exceed, dimensions of 1 x 1-1/2 miles at the surface and go as deep as 1800 feet. The orebody to be stripped was covered by an average of 460 feet of alluvial gravels, which presented an initial stripping job of great magnitude. The initial pit layout and the original time schedule established early in 1965 called for the excavation and disposal of about 250,000,000 tons of alluvial overburden before the end of 1969. Allowing about a year for equipment delivery, this schedule left four years to do the job averaging about 62-1/2 million tons per year. In 1964 when The Anaconda Company undertook the development of Twin Buttes, it was recognized that special planning was necessary for the disposal of waste material and tailings. Environ- mental control was a prime consideration and is particularly sensitive in the Twin Buttes area due to the proximity to residential developments. Disposal of the 250,000,000 tons of alluvium, as well as future rock and tailing waste material, presented a problem which Anaconda engineers resolved by designing a plan to spread out much of the alluvium over an extended area, including a massive 11- 1/2 mile dike system which will impound mill tailing in three basins. The tailing will be impounded behind these-dikes to avoid wind exposure and blowing. The dikes also serve as a

Jan 1, 1974

By R. J. Sandberg

The Copper Creek area, part of the Bunker Hill District, Pinal County, Arizona, lies within the southwest porphyry copper province of North America at the intersection of a northwest trend and an east-northeast trend of Laramide porphyry copper deposits. The Copper Creek area has been mined and explored for copper and molybdenum since the early 1900?s. The majority of this work focused on the more than 400 surface exposed breccia bodies. In the 1960 to 1970?s deeper drilling discovered a deep porphyry copper-like setting. Redhawk Copper currently has NI 43-101 compliant resources of about 0.652 billion pounds of measured and indicated and 2.745 billion pounds of inferred copper equivalent in breccia hosted and porphyry style deposits. See Figure 1.

Jan 1, 2010

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.