Search Documents

By J. P. Ducarme, J. L. Carr, C. C. Jobes

"An average of 1.2 fatalities occur per year in underground coal mines in the United States when a miner is struck or pinned by a remote-controlled continuous mining machine. Proximity detection technology provides a means to prevent these types of accidents by disabling all machine motion when a miner is in close proximity. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed the intelligent Proximity Detection (iPD) system, which continuously tracks the position of miners near the machine and disables only those machine motions that could cause a pinning accident. This system, previously demonstrated using non-permissible proximity detection hardware, has now been shown to be effective when implemented using an MSHA-approved system as a platform. Performance tests have shown accuracy, repeatability, and stop zone identification to be comparable to or better than the system demonstrated with non-permissible hardware. INTRODUCTION Underground coal mining room-and-pillar operations typically use Continuous Mining Machines (CMMs), such as the one shown in Figure 1. When CMMs first became available, they were operated from an on-board operator’s compartment that protected operators from roof falls and other hazards but severely restricted visibility and subjected them to machine vibration and high levels of dust and noise. To solve these problems, remote controls were developed to operate CMMs. Now CMM operators are free to position themselves for best visibility of each mining task and are no longer subjected to the rough motion of the CMM during mining operations or the dust and noise generated by the machine. However, this technological advance removed operators from the protection afforded by the operator’s compartment and exposed them to the hazard of being struck or pinned by the CMM or other large moving machines."

Jan 1, 2015

By T. Yegulalp, M. Castaldi

As global energy demands increase, there will be a critical need to employ fuels that have minimal environmental impacts. While hydrogen is considered the ultimate fuel for that purpose, hydrocarbon based fuels will be in use for a considerable time and will probably be the first major source of hydrogen for next generation power systems. The best fuel for this transition will be natural gas because of the high hydrogen to carbon ratio. Natural gas hydrates have the potential to meet the global energy needs for the foreseeable future. The amount of energy stored in natural gas hydrates is significantly more than that of all the other fossil fuels combined. However, most proposed techniques for recovering the natural gas from the hydrate require too much energy input, raise safety concerns or can only recover a fraction of the gas. This paper discusses the technical feasibility of a novel method of gas production in hydrate reservoirs. The method is an in-situ process that creates a point heat source in the hydrate formation. This method not only significantly reduces the energy input, but also has the potential to sequester as much or more CO2 than would be produced from combustion of the natural gas produced, thus making this in-situ methane production technique virtually carbon neutral. Simulations using FEMLAB™ show that the method offers an energy efficient and environmentally friendly way to produce natural gas from hydrate reservoirs. Preliminary results indicate that it is possible to have an energy efficiency of nearly 90% for land based reservoirs for hydrate loadings of 20%. The simulation results also suggest that alternatives to a point source can be employed which may improve the process efficiency.

Jan 1, 2007

By Werner Wenzel

Methods to increase the gas penetration through sinter layers. In the field of agglomeration, sintering has gained importance, specially in Europe; in Best-Europe this trend will continue till the year 1980, since it is quite probable that in the blast furnace burdens with 50-60 sinter, 10-20 % pellets and 20-25 % ore lumps will be employed. In order to meet this demand for sinter, new sinter bands with reaction areas between 300-400 m2 will be constructed. Chemical and physical phenomena during the Suction-Draught-sinter process. Iron ore sintering is generally considered as a burning process where the material contains 90-95 % ash i.e. non-combustible ingredients. Sintering represents a heterogeneous exothermic reaction in which the chemical phenomena as combustion, calcination, hydration, reduction and oxydation are superposed by physical phenomena. The physical phenomena are devided into material transport and simultaniously occurring heat transport processes. The velocity of these combined physico-chemical reactions i.e. the change in the reaction site per unit time determine the efficiency of the sinter process. The gas permeability as an important criterion of heat transport during the Suction-Draught sinter process.

Jan 1, 1971

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Morgana Rosset, Bárbara da Rocha Pereira

High-purity alumina finds application in various electronic industry sectors, with approximately 100 million tons of this compound being produced worldwide. Alumina is acquired through the mining process of bauxite, a rock composed of a mixture of minerals such as gibbsite, kaolinite, hematite, and either anatase or rutile. In 2020, both bauxite and alumina were included in the list of critical raw materials. Due to the demand for high-purity alumina production, the development of a methodology to remove impurities present in the leach liquor from bauxite processing by solvent extraction (SX) followed by precipitation has been widely studied. This work aims to obtain high-purity alumina from bauxite by a solvent extraction process followed by a precipitation step from the sulfur leach liquor obtained by the thorough dissolution of Al and Fe from bauxite. Different parameters were evaluated in the SX step, such as extractant type, pH, temperature, and volume-to-volume ratio. The results indicated that using Alamine 336 as an extractant at pH 0 and room temperature led to an extraction of 90% of Fe and 15% of Al. Aluminum sulfate was completely precipitated as aluminum hydroxide and 55% of Fe using NH4OH. After the calcination procedure, obtaining a 99.9% pure alumina was possible without generating a red mud-similar residue.

Dec 28, 2023

By Douglas W. Huber

During the past decade, a general awareness of the need for and subsequent development of increased safety in United States coal mines has taken place. Government and industry alike were stimulated into accelerating their actions through unacceptable accident statistics and costs (in terms of human misery dollar values). Those of us who work in the United States coal industry are aware of the development of governmental controls on nine safety. Both Federal and State regulations have placed increased responsibility upon mine owners and operators to insure a safe working environment and to provide training for miners. No other industrial group of workers has received such attention or, in our opinion, deserves it more.

Jan 1, 1982

By L. Alagha, L. A. Sanchez-Calderon

The existing methods for recycling lithium-ion batteries present initial hurdles related to the safe handling and preparation of the batteries to avert potential explosions. Submerging batteries in sodium chloride (NaCl) solution has become an acceptable industrial practice. However, the use of NaCl to discharge lithium-ion batteries rusts the batteries’ cases and releases metals which impacts the downstream processes that involve selective recovery of Li. This study aimed to determine the optimal concentrations and pH range of NaCl for the discharge of lithium-ion batteries for the purpose of minimizing the leach of Al, Co, Cu, Fe, Li, and Ni.

Feb 1, 2024

By Zohreh Kazemi Motlagh, Virginia T. McLemore

Critical minerals are nonfuel minerals, essential to the U.S. economy and national security, whose supply chain may be disrupted. Mine wastes are potential sources of critical minerals. The goal of this project is to estimate and characterize critical minerals endowment in three mining districts in New Mexico: Black Hawk (Grant County), Hillsboro (Sierra County), and Magdalena (Socorro County), and assess their acid-generating potential. The Black Hawk district is an arsenide five-element vein deposit (Ag, Ni, Co, As, U, Bi, and local minerals like Pb, Cu, Zn, W, and Sn). The Copper Flat mine in Hillsboro district is a copper porphyry deposit. The Kelly mine in Magdalena was first mined at 1878 and are carbonate-hosted Pb-Zn deposits. Mine waste rock piles and tailings are sampled using USGS Beta sampling procedure. Geochemistry results show that Black Hawk district mine wastes samples are elevated in Ag (>200 ppm), Co (290 ppm), Ni (2,130 ppm), and Zn (8,463 ppm). Copper Flat mine tailing is elevated in Bi (111 ppm), Cu (7,453 ppm), and Zn (2,360 ppm). Downhole profile plots in Copper Flat show the positive correlation between Cu, S and Te values. Magdalena samples are elevated in Cu (5,700 ppm), Zn (129,500 ppm), and Pb (58,100 ppm). Determination of acid-generating potential in these areas suggests that Black Hawk district mine wastes are non-acid-forming while high S present in some Copper Flat and Magdalena samples can potentially cause acid mine drainage.

Feb 1, 2025

By Hongling Wang, DI WU, Shuai Li, Hui Shu

Isothermal reduction experiments on carbon-bearing pellets of copper slag were investigated by the thermogravimetric method with biomass carbon as a reducing agent. The results indicated that the reduction process of copper slag‑biomass composite pellets was dominated by gas phase diffusion, and the apparent activation energy was 88.44 kJ/mol. In the temperature range from 1000 to 1200 °C, the metallization rate of pellets increased with increasing temperature, and the maximum metallization rate was 78.4%. The optimal reduction temperature of CSBCP (copper slag-biomass composite pellets) was 1200 °C.

Nov 23, 2022

By James A. Clum

The shift to lower grade iron ores, e.g., magnetic taconites, resulted in a shift towards agglomeration practices which could effectively deal with the fine particle sizes generated in the liberation and concentration processes. If the iron bearing particles are not extremely fine, e.g., -1/2 in + 100 mesh, sintering is an adequate means of agglomeration.(1) For the more dispersed ores which result in fine concentrates (more than 80%,-325 mesh), the fine particles must be agglomerated by mechanical means before final hardening, e.g., pelletizing.(1) In the pelletizing process, the essentially mechanical step of balling is extremely critical since the strength of the pre-fired pellet determines the firing conditions. The ability of the proper amount of moisture to hold together a ball of the very fine ore concentrate particles has long been recognized. It is a charac¬teristic of the reaction at the interface between the ionic solid of the ore concentrate and the polar water phase which overlays the solids. The strength in such moisture laden balls, the green strength, is a strong function of the water content (Figure 1) and thus deteriorates rapidly for either a small excess or a small deficiency of moisture. For purposes of commercial practice, the control of green ball handling properties by accurate control of ball moisture is too demanding. Moreover, as the ball is heated towards its hardening tempera¬ture, e.g., 1300'C, there is a substantial drying reaction which would lead to such a low dry strength of the ball that it would not support its own weight much less the weight of other balls in a firing furnace.

Jan 1, 1976

By Glenn Mongillo

Discrete Element Method (DEM) software has been successfully used to simulate various machine/soil interactions and provide insight for industries such as mining and bulk material processing. This paper will investigate typical calibration techniques used in particle models for DEM simulation and physical calibration experiments with soft ground TBM cutting tools to incorporate parameters such as tool drag forces that contribute to required TBM torque. With a well calibrated DEM model, it is expected that TBM simulation results will be more meaningful and provide better insight into TBM performance, power requirements, cutting tool placement, and overall cutter head design.

Jun 13, 2021

The main goal of this paper is to present readers with recommendations for choosing coaxial cables appropriate for mining applications of Time Domain Ref 1 ectometry (TDR) to monitor rock mass movements. Prior to discussing the recommendations, mining applications are illustrated with examples and the operating principle of TDR is discussed briefly. Items that affect the result of the monitoring system performance include the coaxial cable selected, the grouting material used, and the installation procedure.

Jan 1, 1986

Integrated mining information and process control systems can reduce information delays, enhance decision making and improve the responsiveness of mining operations to, for example, variations in market conditions, mineral grades and ground conditions. This paper examines developments in the areas of: monitoring, data analysis and diagnosis,' communications systems; integrated mining support system;, and process and machine control. It concludes that the development of a comprehensive information technology plan is fundamental to the phased implementation of these technologies. In addition, hardware and software standards and concurrent digital design and simulation practices in selected manufacturing industries are examined and concluded to have relevance to the mining industry. Integrated information and process control systems will lead to emergence of the "digital mine". Such advances in mining information infrastructure as well as mining equipment will enable mining operations to shift from mass production methods to leaner production techniques. "Lean mining" aims to enhance and accelerate cash flow over the life of a mine by focusing on reduction of' throughput times; stockpiles for volume and quality control; and wastage and rework.

Jan 1, 1995

By Saman Khaleghparast, Naj Aziz, Jan Nemcik, Guanyu Yang

"More than 25 years of uninterrupted research on ground support technology for underground mines has been undertaken at the University of Wollongong. This research has resulted in significant findings on tendon characteristics and strength properties. The paper focuses on the development of the fourth generation of cylindrically shaped shear test apparatus for assessing tendon performance in shear. This shear apparatus is known as the MK-IV Double Shear Box or Naj Aziz Double Shear Box (NADSB), and is based on the experience gained from the development of previous versions of rectangular double shear boxes. The new NADSB is circular in shape and is fitted with a truss system, which permits friction free shear testing of tendons across joint planes. A series of double shear tests were carried out on a number of cable bolts commonly used in Australian mines, both plain and indented wires, under varied pretension loads. The results were compared with similar test results using rectangular shaped double shear apparatus, with and without friction across joint faces. The significance of wire surface roughness and increased initial pretension loads are discussed and conclusions made, suggesting that indented wires are inferior in shear compared with plain cable bolts. The general test procedure of the NADSB is described and different concrete reinforcement techniques are reported. The influence of external and internal confinement of the concrete medium blocks in a circular double shear box contributed to consistent test results with a minimum of lateral and axial cracks occurring in the host medium.INTRODUCTIONThe use of long tendon ground support elements (cable bolts) is now a common practice in modern underground coal mines, hard rock mines, tunnels and other underground structures. Due to their material properties cable bolts contribute significantly to the overall ground reinforcement provided by a support system. Cable properties in tension and shear are in many cases vital to maintaining a safe and productive underground environment. Accordingly, tension and shear properties must be assessed accurately using both valid and reliable methods.Load transfer property testing of tendons has been studied over several decades with much of the early research focused on the pull and shear testing of solid rock bolts and hollow bolts (like Swellex and split set tube bolts), as these elements were used extensively at this time. It was not until the 1970’s that the use of cables for ground reinforcement developed, and as such highlighted the need to extend load transfer property testing to include shear strength of cable bolts. Initially, the discarded hoisting ropes were used for ground support in metal mines, particularly in stopping wall support and then late in 1980’s cable tendons began to use in coal mines."

Jan 1, 2019

By DING TANG, JINGHE CHEN, Shuiping Zhong, CHEN KUANG

The Zijinshan gold-copper mine, in spite of the low-grade nature of the ore, has become one of the largest production-scale and most profitable non-ferrous metal mines in China. The successful application of hydrometallurgy as well as proper engineering design are the key factors for large-scale development of the Zijinshan gold-copper mine. In this contribution, the practical experience acquired in the development of the Zijinshan gold and copper mines is summarized. This covers most aspects of the production process including mining, beneficiation, ore stacking, heap (bio)leaching, carbon-in-leach, solvent extraction, electrowinning, wastewater and tailing treatments. The authors believe that this practical experience will not only help to promote the development of hydrometallurgy, but can also serve as a model for other gold and/or copper plants around the world.

Jun 3, 2020

By Steven P. Oman

Large room and pillar mines are characterized by numerous and widespread working places. Ventilation requirements are high since each panel employs men and equipment that work simultaneously in multiple headings. Also, it usually is not feasible to redirect airflow from idle to active panels as the demands of each shift vary so every panel in the mine is fully ventilated at all times. Ventilation requirements will be even higher for mines that are classified as gassy. As a result of these considerations, ventilation systems for room and pillar mines are generally designed to handle large quantities of air. But as mining progresses and the mine be- comes larger, greater demands will be placed on the ventilation system. To insure that adequate ventilation is maintained at these times, ventilation engineers must anticipate problems and plan how best to deal with them.

Jan 1, 1983

By A. Thatcher, C. Day, C. Meyer

The purpose of this paper is to provide general information about the bioaccessibility of metals and specific information about the use of bioaccessibility in risk assessments (human health risk assessments [HHRA] or ecological risk assessments [ERA]) and a list of sites where regulatory agencies have approved the use of bioaccessibility data in risk assessment. The memorandum also cites current U.S. Environmental Protection Agency (USEPA) guidance as well as state specific guidance where applicable. BRIEF HISTORY OF METAL BIOACCESSIBILITY TESTING AND METHODS The bioaccessible fraction of a constituent is that fraction that dissolves or desorbs from its matrix (e.g., soil) in the gastrointestinal tract and is available for absorption (USEPA 2007a; ITRC 2011; ITRC 2017). This is different from the bioavailable fraction, which is the percentage of the amount of an element that an organism is exposed to that is absorbed by that organism during a given time under defined conditions (USEPA 2007a). The bioaccessibility factor is the percentage of a metal that is potentially available for absorption and, therefore, is a conservative estimate of the bioavailable fraction since all that is available for absorption may not ultimately be absorbed into the organism’s system. Currently, there are two main techniques for estimating bioavailability of metals within a medium: in vivo animal studies (time-consuming and often cost-prohibitive), and in vitro tests that simulate human, or animal digestion in a laboratory setting. In vitro and in vivo test methods and protocols have been extensively evaluated by numerous researchers (Ruby et al. 1996; Rodriguez and Basta 1999; Sips et al. 1998; Sips et al. 2001; Molly et al 1993; Oomen et al 2002; Kelley et al. 2002; Oomen et al. 2003; Furman et al. 2006; Drexler and Brattin 2007; Basta et al. 2007; Wragg et al. 2009; Wragg et al. 2011; Chaney et al. 2011; Bradham et al. 2015; Bradham et al. 2018). The most recent scientific literature demonstrates that protocols used to estimate the bioavailability of metals to mammals also predict bioavailability of metals to birds as well (Beyer et al., 2016).

Jan 1, 2019

By R. R. Guzman

In this study, the "Mine Project Risk Management" methodology, MPRM (Botin et al. 2011), has been applied to characterize the sources of uncertainty and to quantify risk in the mining engineering stages of Block Caving mining method. As the result, rock mass caveability and ore fragmentation were identified as the two most relevant parameters of this process and a methodological model has been developed to quantify the risk associated to each of these two parameters. Furthermore, the applicability of the proposed model has been validated using as a case study the Chuquicamata Underground Mine Project in Chile.

Feb 23, 2014

By S. K. Sharma

The Bureau of Mines has investigated the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters such as shear rate, polymer dosage, and polymer concentration on floc growth and to determine the applicability of a model in predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. Results show that the model, using GA as a tool to determine the unknown parameters, reproduces the experimental data with only reasonable accuracy and was relatively insensitive to the parameters. Results of the flocculation study showed that increases in polymer dosage had greater effect on the time required to reach the maximum floc size than on the floc size itself. It was also determined that, given all the aforementioned parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on the floc growth.

Jan 1, 1993

By David Chastka, Isidro Rivera, Shawna Von Stockhausen, Idit Zarchi

The City of Santa Cruz Water Department is replacing the existing Newell Creek Dam inlet/outlet works at Loch Lomond Reservoir in the San Lorenzo Valley. The project will improve the City’s overall operational efficiency, improve system performance, and improve the safety and reliability of storage for the City’s drinking water supply. The project comprises new inlet works* (three new inlets that control and convey flows into and out of the reservoir, and an intake control building), an inlet/outlet tunnel with a 48-inch conduit to convey flows into and out of the reservoir, and a new outlet structure at the toe of the dam. The outlet structure includes a release point for energy dissipation of emergency drawdown flows, a connection to Newell Creek Pipeline, and beneficial releases into Newell Creek. The project also includes a new dam seepage collection and monitoring system and appurtenant structures such as a culvert bridge over the spillway plunge pool to improve access to the new outlet. Notable complex project components include in-water work to connect the new intake shaft pipes to the three new inlets. The project includes one major milestone with a work window regulated by environmental permits that could only be amended/ extended with approvals from those agencies. If not met, the milestone work would have caused significant delays (potentially up to one year) to the project.

Jun 13, 2021

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), the authors showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/tonne of REEs occur in AMD and AMDp respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. Geospatial analysis identified a total resource of 340 tonnes stored at the 141 sites sampled in this study. While this analysis did not quantify the basin-wide REE inventory, it does indicate the impact that processing cut-off grades will have on the overall AMDp resource base.