Search Documents

By Richard Cole

The Energy Act of 1992 has many users of ac-induction motors eyeing premium-efficiency motors with mixed feelings and perhaps some confusion. When the October 1997deadline arrives for compliance with the1992 standards, the winners will be the environment due to reduced need for more power generating plants and the petroleum economy because of reduced dependency on foreign oil. But what will it mean for industrial users? The most obvious benefit is the potential for smaller electricity bills. Motors account for about 64% of the electricity consumed in the United States, at a yearly cost of $112 billion. Every 1% reduction in motor demand cuts 0.64%, or $716 million, off the industry wide bill. Higher efficiency motors also run cooler. This lightens the load on air-conditioning systems and further reduces plant demand. Lower total demand can lead to lower rates by helping to minimize peak-demand surcharges. As rates increase over time, these savings get bigger.

Jan 1, 1996

By Y. C. Lo

This paper presents the development of ultrasonic grinding technology for material and mineral processing. The principles underlying this new technology, as well as their implementation in two laboratory scale devices are described in detail. Ultrasonic grinding experiment results are discussed with respect to operating variables and the achieved product sizes. Special attention has been given to the electrical energy consumption of the grinder, and an attempt to compare its efficiency with tumbling mills has been made. A mechanical system capable of measuring the specific grinding energy is also described.

Jan 1, 1991

By Robert L. Zook

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25-30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large scale mapping which allowed sub-surface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the Modified Fellinius Slip Circle, Simplified Bishop Slip Circle and Analysis for Translational Failure -were utilized. In all stability analyses hydrostatic pressure and earthquake were considered. This investigation indicated that 62% of the embankments analyzed are in a stable condition. The coal seam mined, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these em¬bankments should not be treated as pure state-of-the-art dams; consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dim slurry impoundments generally lack the site se- lection phase that is standard practice with siting most other types of dams.

Jan 1, 1974

By J. A. Cole

This paper discusses the modification of the cyanide tailings treatment method from ferrous sulfate to Caro's acid (peroxymonosulfuric acid). An examination of the operating parameters, costs, and chemistry describes how the decision was made to switch to this treatment method. Plant data collected from the last several months will be used, along with considerations from an operator's viewpoint.

Jan 1, 1996

By M. P. A. Hames, D. R. Beaumont

INTRODUCTION Legend has it that when Isembard Kingdom Brunel was confronted with the cost and consequences of one of his bridges having failed, he responded cheerfully that the event had saved investors and taxpayers a fortune because it prevented him from repeating the same design at several other locations. To meet the demands of rejuvenating and expanding the transportation system in an era of industrial growth Brunel and his contemporaries introduced bold designs and many innovations. Great advances in design and construction techniques resulted, yet these too had their practical limits as the story tells. In the gold mining industry today we face the same challenge of expansion, yet designers must respond mindful of economic restraints. Is innovation the answer? It has two meanings; to bring in novelties and to make changes. Distinguishing between improvement and novelties, or simply recognizing the benefits and limitations of new ideas over proven technology is part of good design. This paper will illustrate the practical aspects of selecting appropriate solutions to a design problem by examining a variety of examples common throughout the industry. Since a variety of engineering disciplines contribute to the design of a gold processing plant, and each has some old wisdom to impart or new development to boast this paper is divided into the different areas of expertise involved.

Jan 1, 1987

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has developed a laboratory apparatus for continuous separation of minerals according to their dielectric properties. The unit consists of a rotating wire grid drum electrode and a fixed curved wire screen electrode positioned 3 mm apart. By applying high voltage across the electrodes, which are immersed in a dielectric fluid medium, a high-gradient electric field is produced. The high-dielectric-constant minerals are attracted and conveyed through the separator by the rotating drum electrode, whereas the low-dielectric-constant minerals settle through the fixed electrode. In typical tests, a sample of Montana chromite ore containing 43 percent chromite was concentrated to 72 percent chromite with 90 percent recovery.

Jan 1, 1977

By Raymond F. Moran

The history and development of the FMC Coke process has been reported in numerous presentations over the past 10 years (1, 2, 3, 4, 5, 6) but a short review is desirable, especially regarding the aspects that are influenced by the coal to be used. F'MC has been developing this process in pilot facilities since 1956 and in a modest sized plant in Kemmerer, Wyoming since 1960 (Figure I). This plant produces strong uniformly sized coke briquettes from a completely non-coking coal, namely Elkol, a sub-bituminous coal of the Adaville seam. Since operating commercially, over 300,000 tons have been produced, 90% of which has been used in electric phosphorus furnaces and some 10% of which went for trials in iron blast furnaces. We believe that this commercial use of non-coking coals is a unique experience in the history of coke manufacture.

Jan 1, 1975

By Karen Mikkola, Gerald Luttrell, Jaisen Kohmuench, Glen Oswald, Michael Mankosa, Tracy Westerfield

Hydraulic separators are commonly used for particle size classification and gravity concentration of minerals and coal. Unfortunately, the efficiency of these processes can be quite low due to poor equipment design and variations in feed consistency. To help alleviate these problems, an industry-driven R&D program has been undertaken to develop a new generation of hydraulic separators that are more efficient and less costly to operate and maintain. Two of the most promising technologies, the CrossFlow and HydroFloat separators, have now been tested at industrial sites. The data obtained from these sites have been used to illustrate the potential performance improvements that can be realized through the application of these high-efficiency separators.

Jan 1, 2005

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By Robert J. Timko, Lincoln Derick

This work is a follow-up to previous research that attempted to predict the location of spontaneous heating episodes in underground coal mine pillars. The objective of the original work was to see if the data obtained by commonly used detection methods could accurately predict spontaneous combustion episodes in coal pillars. Data accumulation during the study was enhanced when a spontaneously generated fire occurred within one of the pillars being examined. The fire provided researchers with realistic data that could be used to determine if fire prediction was possible. Results from the initial study found that the atmospheric status equations that were used provided little advance notice that combustion would occur where it did. This study reevaluated the accumulated data by applying it to recently developed equations and compared these results with previously obtained information to determine if a combination of these techniques could more effectively predict impending combustion.

Jan 1, 1995

By W. H. Strickland

The research reported here characterizes ultrasonic ranging sensors for autonomous navigation on underground mine mobile equipment. Because ultrasonic rangers are inexpensive, have no moving parts, have no lenses to clean, are small and unobtrusive, and can measure distances in dusty environments, they are especially sui ted to underground mi ne environments. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of individual rangers and a ring array of 24 sensors. The results showed the sensors have good accuracy and low variability. Additional experiments at AHAX&apos; s Henderson mine Showed the sensors could accurately and reliably measure rib features, convex and concave corners, and drift intersections. The results showed that when used and analyzed properly, the sensor data may be used reliably for underground mobile equipment navigation.

Jan 1, 1990

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

The paper addresses heat stress in underground coal mines, which poses significant threats to miners’ health, safety, and productivity. It involves a comprehensive ventilation survey in three deep and mechanized underground coal mines in India. Using VentSim software, 3D simulation models were developed to predict heat stress conditions and explore the application of auxiliary ventilation and spot coolers to reduce heat stress.

Oct 1, 2023

By Molood Saeedi, Nima Sadeghi, Eskandar Keshavarz Alamdari

This study showed the kinetics of gold chlorination leaching from an anode slime complex containing copper, silver, barium, selenium, and tellurium. AgCl and BaSO4 control the rate of gold leaching, and the interface transfer and diffusion across the product was selected as the desirable kinetic model. The concentration of hydrochloric acid, chlorine gas flow rate, pulp density, and temperature have been precisely studied. The results showed that temperature and hydrochloric acid have a favorable influence on the leaching rate. However, the chlorine gas flow rate is inactive in the reaction rate. Furthermore, the leaching rate decreased with an increasing pulp density. The leaching process was controlled by the interface transfer and diffusion across the product, and the activation energy was determined to be 13.66 kJ mol–1.

Oct 19, 2021

By Klaus Rabensteiner, Klaus Chmelina

"INTRODUCTION Urban tunneling is often related with special geotechnical risks. Typical causes are difficult (hydro)geological conditions, a very low overburden and the presence of critical and vulnerable (infra)structures in the influence zone of the construction (e.g. existing tunnels, roads and pavements, sewer pipes, gas and power lines, landmarked buildings, historic monuments). To manage these risks appropriately, an early detection and warning of unexpected behavior of the affected geotechnical objects ground and tunnel, as well as existing structures are mandatory. To accomplish this, the design and execution of a dense geotechnical monitoring program is of high importance. In more detail, this means specifying and performing a systematic and continuous acquisition, processing and analysis of monitoring data to support decision making. In recent years the development of new automatic sensors and (wireless) data transfer techniques and the general trend towards an automatic acquisition of monitoring data has led to an enormous increase of data production frequencies and volumes. In order to handle this data explosion efficiently, information systems and geo-databases have been developed and used successfully in many projects. They represent IT tools that support the different tasks of a given geotechnical monitoring program including data acquisition, transfer, check, processing, backup, analysis, distribution, reporting and, last but not least, alarming. Meanwhile, some tools already have developed the capability to connect to other theme-specific databases used in the project and, thus, serve as a central data management system for all kind of digital data produced. This makes possible the implementation of further useful functions and services supporting tunneling tasks such as machine control, tunnel simulation, geological prediction, process optimization, etc. where data from different engineering disciplines must be combined and processed in an integrated way. In the following chapters our aim is to describe how monitoring data management, geotechnical monitoring, alarming and reporting are organized and technically implemented at the metro project Cityringen in Copenhagen (Denmark). We want to highlight the specific role and tasks of the used tunnel information system in the project, and particularly inform on the most relevant challenges."

Jan 1, 2016

By Olivier Martin

In busy and historic cities, traditional open box metro stations are becoming outrageously difficult, unacceptable for the citizen and uneconomical. Hybrid stations provide an interesting alternative. In-house experience of Gautrain (South Africa), West bay (Qatar), Cairo line 3A (Egypt), and Melbourne (Australia) all aim to reduce disturbance to the city and its inhabitants during construction. Constructed in rock or in deep soil under water table, they take advantages of the latest construction techniques from cement grouting to freezing, and from traditional excavation of cavern to large tunnels constructed by sophisticated tunnel boring machines (TBM). Today, they form the ultimate construction challenge.

Jun 13, 2021

By C. K. Blankenship

The competitive forces now driving the electric utility industry and the constraints of regulation at all levels are changing the way we will all do business now and into the next century. Utilities are using every technological tool at their disposal to find optimum solutions to challenges in every aspect of operations. In fuel planning and procurement, these tools include models that predict which dispatch line-up will comply with environmental regulations at minimum cost. This paper presents how those tools are being used for Duquesne Light Company.

Jan 1, 1995

By M. D. Carter

The availability of environmentally acceptable and reliable energy sources is an important issue for Federal, State, and local planners. A cooperative program by the U.S. Geological Survey, State geological surveys, and the U.S. Bureau of Mines has developed a national GIS-based systematic effort to collect, analyze, and depict data characterizing the relationship between restrictions to mining and the potential development of the Nation&apos;s coal resources. Land use/environmental and technologic/geologic restrictions are identified within selected 1:24,000-scale, 130-to 150-sq-km 7.5-min quadrangles and applied as overlays to maps of coal-bed thickness, depth, and mined-out areas. Tonnages of original, mined and lost-in-mining, remaining, restricted, and available resources are calculated. Resultant data files are transferred to the Bureau of Mines for recoverability and cost analysis.

Jan 1, 1995

By M. S. Klima

Coal gasification solid residue (slag) contains unconverted carbon (char), which is considered an impurity for utilization applications of slag. Under this study, table concentration was used to process approximately 24,000 pounds of a nominal-3.4 mm gasifier slag (-85% ash) to separate high (-100%) ash slag from low (-50%) ash char. The results indicated a nearly ideal separation of the slag from the char for sizes coarser than about 1 mm. An overall slag yield of 71 % was obtained. The slag was sufficiently clean to be used as feed material for the production of expanded lightweight aggregate. The recovered char had an ash content of about 47% and was a nominal -1mm in size.

Jan 1, 1997