Search Documents

By James McNally, Adam Stremcha, John MacGregor

With 13.7km of TBM tunneling in Atlanta’s hard gneiss well under way, drill and shoot work continues on several sites throughout the city. In order for the City of Atlanta to meet the consent decree imposed by the federal government, an aggressive construction schedule was a necessity. Construction consists of two deep, large diameter tunnels, four construction shafts, a pumping station, one overflow shaft, three large intake structures, and two connecting tunnels. Due to the multitude of blasting insensitive urban environments, a high standard of seismic and air-overpressure criteria, coupled with time restrictions, was adopted for the project. At any given time, drill and blast operations were under way at four of the seven sites requiring a certain amount of coordination between the TBM excavation, surface work, and the forces of Mother Nature. This paper addresses the challenges faced and the techniques used to safely and successfully complete the rock excavation of the West Area CSO Tunnel and Pumping Station project.

Jan 1, 2007

By F. B. Olender

Idler engineering, operation, and maintenance cannot be covered in depth in a short paper. Therefore, this will be a general look into the subject matter in light or the present-day technology. Depending on the source or reference used, belts for handling bulk material underground came into being between 1900 and 1920, while strip mining appeared in the thirties. The conveyor belt speeds in that era were in the 300 rpm to 500 rpm range. Belt speeds or 600-700 rpm were in vogue in the thirties, and the early sixties saw speeds or 800-900 rpm. Today, speeds or 1000 rpm are not looked at with dismay; in fact, speeds or 2000 rpm are being discussed. Among the driving forces moving the bulk materials handling industry to these greater heights have been the mining operators and engineers. Their appetite to increase output, yield, and reduced per-ton costs has constantly challenged the bulk material handling industry to develop products capable or handling these increased capacities. One or the products affected by this movement is the idler. Apart from the conveyor belt itself, it is one or the most significant parts or a conveyor system because or the sheer numbers needed in an installation.

Jan 1, 1971

By William J. Francart, Edward J. Miller

The utilization of computer based monitoring systems for fire detection in underground coal mines has grown significantly in the past seven years. In 1984, an annual MSHA survey identified a total of 38 systems being used in U.S. underground coal mines, while a 1990 survey indicated the number has risen to 112. The applications for mine monitoring have also changed according to the annual surveys. From April 24 to June 21, 1990, investigations were conducted by personnel of the Ventilation Division, Pittsburgh Health Technology Center, in cooperation with Coal Mine Safety and Health, concerning the installation and operation of Atmospheric Monitoring Systems in underground coal mines. These investigations were conducted to gather information concerning the ability of the AMS to detect fires and heatings, false and nuisance alarm frequencies, information related to system maintenance, and information related to employee training on system operations. This paper addresses current applications of the systems, fire and heating identification rates, application of systems in dieselized coal mines, system maintenance, and employee training requirements. While deficiencies were identified in some applications, results of the studies and survey indicate the use of atmospheric monitoring systems can be effective in identifying mine fires and heatings.

Jan 1, 1991

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1993

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1991

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

By I. Raposo, I. Moreno-Ventas, A. Palma, M. J. Díaz, M. Vázquez

The oxidative degradation kinetics of chalcopyrite have been studied by thermogravimetric analysis (TGA). The obtained data are necessary for the kinetic description of the flash fusion process, which can contribute to the optimization of the smelting process in copper extractive metallurgy. Activation energy (Ea) evolutions of the involved processes have been determined by several isoconversional methods; in this sense, the chalcopyrite oxidation processes could be adequately described, among studied models (E1641–16, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman), by the Kissinger–Akahira– Sunose kinetic model. Using this method, Ea and A values are found to be very dependent on the conversion. Under lower conversion levels, higher Ea and A values have been calculated with respect to that found for medium and higher conversion levels.

By William Gleason

The Society for Mining Metallurgy and Exploration (SME) has a long and proud history of being the world?s leading resource for the dissemination for technical information regarding the fields of mining and mineral extraction and processing. That reputation was met, and maybe even exceeded, with the programming for the Society?s 2014 Annual Meeting in Salt Lake City, UT Feb. 23-26. The meeting drew more than 6,700 attendees to the three-day conference that featured more than 90 technical sessions with 670 presentations. These sessions covered the breadth of the mining and minerals industry, but it was the so-called ?softer issues? that were discussed in the keynote session that kicked off the meeting. The keynote session, ?Community Engagement: Building Partnerships for Mining,? brought together some of the leading voices from the mining industry, as well as some of the top voices from nongovernmental organizations (NGOs) that work in the mining sector. The common ground between the panelists was their dedication to working to ensure a social, economic and environmental balance in the development of mines. ?We wanted to bring these NGOs in to begin a dialogue to see how we can work together,? said SME President Jessica Kogel. ?This is a space that SME has not typically operated in, but one in which SME can bring a technical, scientific voice to the discussion. SME wants to play a leadership role in creating partnerships between the technical, social and economic areas that are crucial to the success of any mining project.? In today?s environment, finding mineral deposits and extracting the minerals in an economically viable manner is just one piece of an increasingly complex puzzle. Earning and maintaining a social license to operate requires careful consideration of local and global impacts. The industry often comes under intense scrutiny when a new project is proposed and, therefore, it must strive to meet the highest ethical and environmental standards. Success requires cooperation and collaboration between the industry, community and NGOs.

By John W. White

Anthracite mine refuse, or culm dump material as it is sometimes called, is the waste material resulting from the sizing and cleaning of run-of-mine deep and strip-mined anthracite coal. It may also contain mine rock, carbonaceous shale, pyrite, and other debris from mining operations. This material is generally stored in piles or banks, some of which are over 100 years old. Many of the older banks contain a considerable amount of good coal, particularly in the finer size ranges, since these sizes did not have any particular economic value in the early days of anthracite mining. Today, the refuse material from a cleaning operation must be piled in an orderly fashion and in such a way as to minimize the tendency to ignite. There are well over 400 of these banks in the anthracite region containing over 1100 million tons of refuse located in the north-eastern part of Pennsylvania. The banks range in size from a few thousand tons of material up to as much as 13 million tons. Most of

Jan 1, 1972

By Joseph D. D?Annunzio

The report on cut and cover construction as assembled by the Organization for Economic Co-operation and Development covered 17 different countries based on a total of just under 400 individual replies of which about 30% of the replies were from the United States. In general, the review of replies to the questionnaire led to the impression that cut and cover construction is a very inadequate method which needed many improvements. This unfavorable judgment, however, resulted in the manner in which questions were asked rather than in the method itself, It can be concluded that the cut and cover construction method has proved itself as an excellent method and that it has reached a high degree of technological perfection, but inadequacies stilt exist, and for purposes of complete evaluation, comparisons with mining tunnelling methods should be carried out. The principal problem in cut and cover construction is the interaction during construction between the construction process and the existing use of the surface and subsurface environment. The greatest impediments to cut and cover construction have little to do with the physical works being constructed, but more with creating a site in which the work can be performed. Utility relocation, traffice maintenance, and protection of existing structures are major problems for the construction contractor, and too frequently receive insufficient attention in preconstruction planning and design. Some OF the areas in which research should be undertaken are as follows:

Jan 1, 1970

By P. C. Schmall

Ground freezing has been used for the sinking of deep mine shafts for more than 140 years. While advances in refrigeration technology have refined the overall freezing operation, the basic ground freezing concept remains the same. This paper presents an overview of the ground freezing process and the unique advantages that ground freezing brings to shaft construction. Design and construction considerations, including instrumentation and monitoring, are discussed. Case studies are presented to illustrate ground freezing applications for mine shaft installation.

Jan 1, 2010

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By William Gleason

"It has been more than 10 years since Montana Resources’ copper/molybdenum mine has had a lost-time injury at its site in Butte, MT. With more than 350 employees and an average production of about 15.5 Mt/a (17 million stpy), which includes 29.5 kt (65 million lbs) of copper and 4 kt (9 million lbs) of molybdenum, the mine’s journey to a decade of exemplary safety is an impressive feat that has required hard work, commitment and, most of all, leadership from every level of the operation.It has not always been an easy journey, nor has it been one without scrapes and bumps along the way, but it is one that has produced stellar results. Mike McGivern, vice president of human resources, and Pete Steilman, safety manager at the mine, spoke with Mining Engineering about how the operation transformed from a site that was accustomed to collecting citations for safety violations to one that is now collecting awards for its safety record.Simply put, Montana Resources has made safety a value and the people its top priority.The operations faced many predictable challenges in 2003, when the mine was being brought back online after three years of sitting in care-and-maintenance status. It had been shuttered in 2000 because of low commodity prices and high operating costs, and, in the three years that the mine was idled, the equipment became dilapidated, and some of it was no longer in compliance. Less than half of the workforce returned to the site for the restart, and the team was challenged with getting the gears turning again to produce copper and molybdenum. But the most daunting challenge of all of was keeping the workforce safe during the transition.In the first few years of operation the mine racked up citations from the U.S. Mine Safety and Health Administration (MSHA) at an alarming pace, so much so that in May 2006, Montana Resources received a letter from the MSHA District Office informing the company that the operation was being placed on the Potential Pattern of Violations list due to its excessive citation history and high rate of significant and substantial citations. It was clear that something significant had to be done to change the course of action at the mine."

Oct 1, 2019

By Makoto Terada

The most important consideration in planning the plugging and sealing of a mine for mine water control is to predict the water flow from the mine. For this purpose, a method of numerical analysis on the water behavior in the ground at the concerned mine area was developed and the mine water flows were simulated. A hydrological survey at the surface of the mine determined the recharge rate of ground- water and the apparent permeability of ground.

Jan 1, 1982

By A. Habibi

The ventilation survey was conducted in an underground longwall trona mine. The mine is relatively shallow and categorized as a gassy mine. The ventilation system consists of nine shafts (three intakes and six exhausts). Three surface based axial fans ventilate the mine configured in a blowing arrangement. Following the ventilation survey airflow quantity, frictional pressure losses and air psychrometric characteristics have been quantified. An accurate resistance survey has been conducted to calculate the pressure drop with regard to moving cages and skips in the shafts. This paper discusses the benefits of utilizing high accuracy digital pressure transducers and psychrometers in a ?leapfrogging? survey to gather data needed to build the computer ventilation model. Two underground booster fans with VFD are currently idle but available at the mine. The ventilation model has been used to determine the optimal booster fan locations to decrease the overall operating cost by reducing the load carried by the main fans. A leakage study has been conducted to evaluate the effects on the system of additional pressure from a booster fan. The study finally prepares a future ventilation model for the next fifteen years of mine operation and investigates the effect of proposed scenarios.

Feb 27, 2013

By Gabino Preciado, Louis Sandbak

Corrosion has long been identified as a potential risk to the long-term ground support stability due to degradation of internal ground support elements such as rock bolts but also to surface support from mesh, straps, bolt plates, and ancillary support of utilities such as hangers. The emphasis is to understand the corrosion mechanisms on the primary ground support elements and any supplemental steel or arch sets. The water and chemical processes from oxidation(rust), stress corrosion cracking, and even the electrical charge created during these reactions contribute to the corrosion of the steel support elements. The main goals are to mitigate the effects of corrosion and to be able to predict those areas of high water or high sulphide for potential rehab maps. It is also essential to identify and classify the visible corrosion as part of damage mapping and provide bolt testing to those areas of suspected internal damage from corrosion. This is important to get an estimate of the support longevity or expected life before rehab to minimize the overall cost of the operation.

Feb 1, 2024

By A. Kaina

The San Luis deposit is one of the few documented gold deposits on a detachment surface. This paper presents mineralogic and geochemical data that was gathered to characterize the mineralization, classify the ore deposit, and provide details of the ore forming process. Included are data on the paragenesis; alteration-mineral assemblages major and trace element geochemistry, and fluid inclusions. The San Luis deposit occurs on the western slope of the Sangre de Cristo Mountains adjacent to the San Luis Basin about 5 miles northeast of the town of San Luis in Costillo County, south-central Colorado. Mineralization was discovered in the district in the early 17th century. Production began in 1890 on lead-silver ores from which the district took the name the old name of "El Plomo". From 1897 through 1934 gold was intermittently produced. Battle Mountain Gold Company took an option on the property in 1987 and proved on ore body comprising an eastern block that has 1,277,300 t ore at a grade of 1.68 g/t and a western block of 9,744,000 t with a grade of 1.34 g/t. Production began in 1990. A companion paper by Benson (1994) describes the San Luis district and the ore body, hence the reader is referred to this or Robert and David (1990) for details of the geology from which the following is summarized.

Jan 1, 1994

By G. S. Austin

New Mexico produced 83% of domestic potash and 27% of domestic consumption in 1992. The potash industry of New Mexico produces sylvite (KCI), langbeinite (K2SO4-2Mg(SO4)2), and artificial K2SO4. Average sylvite grade in New Mexico today is about 14%. The average grade of langbeinite is 8-10% Kp. Commercial potash occurs in the middle or McNutt Member of the Salado Formation (Upper Permian Ochoan Series). The 120-m-thick McNutt Member dips about 1° east and contains 11 of 12 potential ore zones in the Salado. The mineralogy and proportion of clay minerals, up to 7% of the ore, influence optimum milling procedures and ore grade cutoff.

Jan 1, 1994

By Lawrence A. Roe

This paper describes research and development efforts leading to a wet process for the beneficiation of Western talc ores in which the values are primarily present as soft, platy talc mineral. The mineralogy of the ore, as it relates to the logic of utilizing an uncomplicated, attrition-scrubbing sedimentation process is described. Bench-scale laboratory testwork and a pilot-plant test program are described. The pilot-plant program included production of several tons of products. The thickened talc slurries were very difficult to dewater prior to the drying step. Dewatering difficulties were overcome by use of a high-speed centrifuge. The centrifuge cake was dried either by tray, flash or spray drying. The successful use of one high-grade talc product as titanium dioxide extender in paper is discussed. The talc product has extremely low abrasion values, an important characteristic for minerals used in paper manufacture. It is concluded that this wet process for soft talc ores is capable of producing high-purity talc products for paint, paper, cosmetics and other industrial uses re-quiring very pure soft talc.

Jan 1, 1972