Search Documents

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By S. Ripke

Between 2002 and 2004, the performance of a six million ton per year iron ore beneficiation plant dropped significantly. In a classic case of “who done it,” was it the mine, the concentrator, an ore change, or something else? While average annual final product grade decreased 8% (indicated by an increase in silicate gangue from 2.76% to 2.99%), the weight recovery also decreased by 8% (from 37.92% to 34.79%). This represents a loss of 832,000 tons of iron ore worth about $16 million for the two year period! The concentrator had been optimized to produce a high grade wet concentrate as feed to the dry side of the plant. But, did optimizing an individual unit operation’s grade give the best overall plant performance? In this paper, the investigation and solution to this mystery will be revealed.

Jan 1, 2007

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

By William Gleason

Despite a global slowdown in most mining sectors, Caterpillar, the world?s largest mining equipment maker continues to forge ahead with new, and improved offerings to the global mining industry. On Nov. 10, as part of its Loading and Hauling Mining Focus Session at its Tinaja Hills proving grounds south of Tucson, AZ, Caterpillar unveiled to customers and media its two latest mining products, the 994K wheel loader and 6020B hydraulic shovel. The Caterpillar 994K wheel loader builds on a nearly 25-year history of the 994 model but with one noticeable difference ? the 994K is bigger ? much bigger. Weighing in at 239,142 kg (527,218 lb) the 994 K is up to 20 percent larger and comes with up to 30 percent increase in payload capacity. This behemoth of a machine is currently being tested at Caterpillar?s Tucson Proving Grounds, Anglo Gold Ashanti?s Cripple Creek and Victor gold mine in Colorado and Taseko?s Gibraltor copper and molybdenum mine in British Columbia, Canada.

By J. J. Harrington

The pH control system at Kennecott Copper Corporation's Nevada Mines Division concentrator consists of two independent systems, lime dilution and lime addition. Lime dilution is accomplished in a mixing tank where slaked lime and water are introduced proportionately. The desired dilution of the milk of lime is determined by the electrical inputs provided by eight pH probes, one per grinding section. The inputs are averaged and applied to a time base generator. The summation output of the time base generator determines the proportion of lime and water that are to be mixed and applies this input to a voltage sensitive switching device. The switching device provides a signal to one of two relays which will add either slaked lime or water, dependent upon the summation output. The entire cycle is based on a two-minute repetition rate to allow for sufficient mix time. Responsivity is controlled by maintaining a limited maxi- mum solution level in the mix tank. Lime addition is controlled independently within each grinding section. The electrical input from the pH probe in a given section controls the solenoid valves which provide lime to each of the ball mills. The valves remain open within a time range capable of maintaining the pH of flotation feed at a given set point.

Jan 1, 1975

By S. R. Dismuke

Ore at the Magmont Mine in southeast Missouri is extracted by the room and pillar method on two and sometimes three horizons. In 1991, an innovative plan was formulated for recovery of high grade ore in pillars using cable bolts to accommodate spans of more than 27 m (90 ft). A test area was subsequently selected and a recovery plan developed. A cooperative rock mechanics study effort by COMINCO METALS, the U.S. Bureau of Mines and the University of Utah was later established. When initially opened in 1968, the planned production rate was about 1,000,000 tons per year. Due to declining reserves, the production rate was decreased to 630,000 tons per year in November 1992. Pillar recovery now accounts for approximately 40%-50% of the mined tonnage and plays a vital role in allowing Magmont to continue to operate.

Apr 13, 2011

By William H. Eatock

The Saskatchewan ore zone strikes slightly south of East, from the Alberta border to Manitoba; and dips to the South. The conventional mines are located along a broad strike line from Saskatoon to Esterhazy-Rocanville. Nine conventional mines have developed ore bodies at a nominal depth of 915 metres (3000 ft.). One mine had developed an ore body at 1525 metres (5000 ft.) by solution mining. Mining reserves of 100 years are not unusual in this vast ore body. Most of the mines were brought on stream during the 1960s. All the conventional mines were influenced by practices developed at Carlsbad, N.M. By 1970, the industry was faced with serious over-capacity resulting in the cancellation of some projects and the introduction, by the provincial government, of the Potash Pro-rationing Regulations designed to share the available market amongst all the producers. This resulted in production rates as low as 40% of capacity. As a result, the 1970s were characterized by attempts to reduce cost, rather than improve production or processing techniques. In recent years, the plants have all been brought to full capacity, and are currently involved in a massive program of expansion, which promises a period of advancing technology.

Jan 1, 1980

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

By Otto Schumacher

Shortcut methods are commonly employed for estimating mining costs for prefeasibility studies. Most of these methods, however, are suitable for earliest stage studies or for internal discussion purposes only. The experts at InfoMine?s CostMine division recommend that any cost estimate completed for purposes of significant decisionmaking or for compliance with Canada?s NI 43-101 requirements be completed using a determinative itemized method. The same basic principles apply for an early stage, intermediate stage, or advanced stage estimate. The only difference is in the level of detail and effort employed. ? Based on the results of a completed resource estimate, an itemized cost estimate begins with development of a conceptual mine plan. Using a surface mine as an example, four elements are crucial no matter what level of study is initiated. Basic geometry of the ore deposit and waste material, with a determination of the expected ratio of waste to ore, a reasonable pit slope angle, possibly requiring the completion of geotechnical studies to predict the waste-to-ore ratio with certainty. ? Determination of the assumed ore and waste production rates. ? Locations of all ore stockpiles and waste dumps. ? Segmental haulage distances and gradients for ore and waste.

Oct 1, 2013

By William L. Rose

Production scheduling is an integral part of intermediate- and long-range open-pit mine planning, affecting equipment selection, manpower requirements and project economics. The development of mining phases, or pushbacks, is discussed in conjunction with generating the best spatial extraction sequence. An approach to scheduling production from these mining phases is then described. Using computers and a production scheduling algorithm, the impact of cutoff grade and advanced stripping policies can be evaluated through sensitivity studies to maximize the return on project investments.

Jan 1, 1985

By G. Brackebusch, S. J. Jung

Backfilling techniques are widely used in large-scale underground mines. Massive pillars, which have been left in place for stability, limit mining activity. Backfilling allows safe recovery of the ore remaining in pillars and assures long term stability. In deep mines expected high stress can be relieved with the backfill. Initially, waste rock was used to fill the openings with mixed results. The need to improve safety and reduce costs has prompted the industry to investigate alternatives. Hydraulic filling with Portland cement added has shown considerable promise, but little has been done to define the parameters of design effective system. The purpose of this study is to determine the relationship between backfill and mining components that can be used to effectively design a best-case hydraulic backfill.

Jan 1, 2000

By Ralph M. Foecking

The disposal of the phosphate slimes produced by Florida beneficiation operations is perhaps the biggest single problem of the phosphate mining industry. This is an old problem which has not been solved and which is becoming increasingly severe. In a typical phosphate mining operation, the phosphate rock mined is initmately mixed with sand and clay, constituting what is known as matrix. During the beneficiation, the clay and other fine materials are separated usually at -150 mesh, and washed from the phosphate rock in a form of diluted slurry known as phosphate slimes. The quantity of slimes solids and their composition vary considerably with the location but usually represent from 25 to 35% of the ore mined. Because of the affinity that clays have for water, large volumes of water are required to separate the granular material in the matrix forming a dilute slime suspension (1.5 to 3% solids) of colloidal material, which settles very slowly, and thus requires immense impounding areas, which never becomes totally usable land. These ponds also contain about 25 to 35% of the total P205 values mined. The magnitude of the problem represented by the slimes can be appreciated better if we realize that there are around

Jan 1, 1971

By A. Sand

A 2-dimensional computational model based on the discrete element method (DEM) is utilized for modeling of stamp-charged coke making. In this process, a large volume of coal is compacted to one single coal cake before entering the coke oven. Cake densification and mechanical strength development are key factors for the subsequent production of a high-quality coke. An approach is introduced for model calibration utilizing multiple control parameters obtained from a laboratory-scale stamping device. Experimental data on stamper rebound amplitude, attenuation and peak force are compared with simulation output in a pairwise manner by constructing a criteria space, which allows identification of model settings best satisfying the control parameters. The calibration procedure carried out by multiple criteria comparison aided model parameter selection for reproducing stamper behavior in response to the properties of the cake subjected to compaction. This modeling and calibration procedure offers possibilities for numerically studying the densification and mechanical strength development of coal cakes. However, the approach is also more widely applicable to other compaction processes.

Feb 27, 2013

By J. G. Davis

The St. Peter Sandstone is typically a well-sorted, friable, ultra-pure, fine- to medium-grained, quartzose sandstone with silica content higher than 99 weight percent in places. The sand grains are well-rounded, highly spherical and characteristically frosted. Their size typically varies from 2 millimeters diameter (No. 10 U.S. Standard Sieve Series size) to less than 0.08 millimeters diameter (No. 200 U.S. Standard Sieve Series size). A freshly exposed surface of the formation is commonly white with shades of pink and green. Weathered surfaces are a dirty gray or brown and are case-hardened at many localities. Bedding is characteristically indistinct, and the formation usually appears massive throughout. The rock is cross-bedded and ripple-marked locally. The formation is generally porous, permeable and rarely fossiliferous in Missouri. The St. Peter is continuously present in the subsurface in the northern half of the state and along the southeastern edge of the state. The St. Peter crops out in a narrow band that starts in western Montgomery County and runs southeastward, along the Missouri River, to just west of St. Louis and continues south, just west of the Mississippi River, through Scott County. The outcrop belt varies from less than one mile wide to over ten miles wide, and it is over 150 miles in length. The formation dips into the subsurface radially away from the outcrop band. A notable isolated outcrop occurs in Lincoln County to the north of the main outcrop band. The St. Peter is discontinuously present in the subsurface along a band in the west-central portion of the state. It is not present at the surface or in subsurface in the remainder of the state. The formation averages 80?100 feet thick. There is an estimated 3.8 trillion short tons of St. Peter in Missouri. Sieve analyses on drill cuttings indicate three subsurface locations in northeastern Missouri where the St. Peter is greater than 10 percent by weight of sand falling in the 20?40 U.S. Standard Sieve Series size range. The St. Peter was first produced in Missouri in the 1870s for the manufacture of glass. Since that time it has been used as a paint additive, filler material, polishing compound, filtering media, and recently it is commonly used as a fracture proppant in oil and gas wells. The St. Peter is currently quarried and produced in Missouri from four sites located in St. Louis, Jefferson and Perry counties. In the same area there are at least nine abandoned historic mine sites.

Feb 27, 2013

By Wayne S. Cavender

The geochemical association of arsenic and gold in epithermal precious metal deposits of the Basin and Range province is well documented, and in this paper I wish to discuss the evaluation and utilization of this element association for geochemical gold exploration. In 1961-62, I conducted an exploration program on lands controlled by Getchell Mine, Inc, and centered about the Getchell gold mine itself, Besides exploring for new gold deposits, the program was to evaluate these lands for potential deposits of any type; thus, a multi-phase program encompassing a number of exploration methods was conducted. I shall not elaborate on the process of designing the program or of integrating the various methods, but for gold exploration, geochemical methods were determined to have the best potential. This paper is based on that effort. Figure 1 shows the exploration area, which covers the northern half of the Osgood Mountains in eastern Humboldt County, Nevada. The Getchell $line is on the east flank of the range and is about 40 miles northeast of Winnemucca.

Jan 1, 1964

By R. W. Guill

For the past five years, Small Mine Development has been involved in the development of small grade underground projects. These projects have been in tough environments where solutions have been found by placing emphasis on creative collaborations by small work forces and selected specialists. This has created an environment where constant innovation and change have become standard operating practice. The cornerstones of these efficient operations have been formed using pneumatic backfill, creative shotcreting, specialized equipment, and highly motivated people. The results realized have served to turn interesting properties into productive operations.

Jan 1, 1988

By Eugie Kabwe

The increase in depth of mines due to the depletion of surface deposits leads to unsafe tunnel construction and overall ore extraction. This is due to tunnel instability associated with the surrounding rock mass’s ability to exhibit creep that occurs over time. However, the explicit description of this mechanism using conventional constitutive models has proven to be difficult and inadequate. Hence, this paper presents an integrated viscoelastic viscoplastic visco-damage model with the Duvaut-Lions function. The presented model is calibrated by experimental data to determine the viscoelastic viscoplastic and visco-damage parameters. It is further implemented in a finite volume numerical code and verified on an experimental scale by numerical modeling of a cylindrical specimen. It describes the 3-phase creep mechanism perfectly as compared to the inbuilt conventional integer-order derivative model. Results from the conducted verification show that it can successfully be employed to describe the long-term behavior associated with the creep mechanism.

May 16, 2021

By Fred T. Towne

There are a number of air classifiers manufactured throughout the United States and the rest of the world. The classifiers manufactured by Alpine, A. G. of Augsburg, Germany, are unique in their abilities. It is this uniqueness that I wish to delve into and in this respect we will limit this discussion primarily to the classifiers as manufactured by Alpine. It has been reported in the past that these classifiers were introduced into the. United States in the late 50's. Until the introduction of the Alpine Classifiers, air classification seldom produced a satisfactory fractionation of a product below 45 microns (325 mesh) or above approximately 22 mesh. It has been a common practice to classify fine materials which used water as a carrier medium The use of centrifuges are today producing thousands of tons of finely partitive powders in the very small particle size range. The use of centrifuges in connection with wet grinding mills has increased the rates of production of these mills considerably.

Jan 1, 1965

By J. Evans

Including: Tailings thickeners, CCD?s, paste thickeners, HI-rate thickeners, lamella thickeners, high compression thickeners, clarifiers etc. Flocculant dosing control for mining thickeners and clarifiers is influenced by a number of process factors. 1. Flow rate into the thickener or clarifier a) As the flow rate increases into the thickener or clarifier ?retention time? decreases which causes a greater affect hydraulically on the settling solids. So as the flow rate increases it will generally mean an increase in flocculant dosing rate. b) As the flow rate decreases into the thickener or clarifier the retention time increases which reduces the hydraulic affect on settling, improving settling rates. This will generally mean that as the flow rate decreases, we will decrease the flocculant dose rate.

Jan 1, 2011

By J. H. Dietz

The electric assist option for diesel-electric trucks can improve truck productivity while maintaining the inherent flexibility of a truck and shovel operation. In addition, the resulting cost reductions offer a rapid investment payback for many mine situations. A review of the present technology and performance experiences verify the projected benefits in productivity and operating cost. New technologies can further improve the productivity/cost scenario.

Jan 1, 1984