Search Documents

By John J. Mulligan

Coal is found in every major geographic region throughout Alaska and in two offshore areas. Since about 1852 over 100 small mines have opened and closed. Last years production was almost entirely from one mine in central Alaska. Clearly the utilization of Alaska's abundant coal resources presents political, economic and technical problems that are far from solution. Location and Physical Features Figure one illustrates the geographical and geological similarity between Alaska and western United States. The Arctic region of Alaska generally resembles Wyoming and the Dakotas. The Brooks Range is an extension of the Rocky Mountains. The Central region of Alaska between the Brooks Range and the Alaska Range bears a general resemblance to the basin and range country of western United States. The Southcentral and Southeastern regions has a similar resemblance to the Sierra Nevadas and the west coast of the United States.

Jan 1, 1982

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By Siddhartha Agarwal

The mining industry collects a significant amount of operational data. However, gleaning useful information from the terabytes of data is difficult, and not just because of the sheer volume of the data. Therefore, an automated tool was developed at the University of Alaska Fairbanks to go through data and apply sophisticated statistical and neural network techniques in order to identify the data streams that are important to a process. This paper presents results from the tool as applied to SAG mill data from a gold mine. The results were compared to results achieved earlier with available commercial modeling tools. The comparison indicates that there was little or no loss in performance by automating the very complicated process of neural network modeling. Therefore, the intent of the exercise, to examine if complicated modeling tasks can be automated, was realized. Mining Engineering, 2011, Vol. 63, No. 12, pp. 52-54. Official publication of the Society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risk associated with the design of mine waste management facilities. These experiences show that the technical and managerial challenge of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur to this day in both developed and developing countries is indeed remarkable, and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailing storage facilities are, in many cases, more demanding than those of conventional water dams, because seepage of fluids which contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 1999

By R. D. Begley

This paper will present detailed design drawings of a flexible single floor residential superstructure proposed for both longwall and room and pillar mining conditions. All efforts were made to provide an immediately available economical alter- native for future home builders on subsidence prone land. Based on this fact, a basement was not included in the design because additional costs and measures would be required to minimize cracking and leakage. A cost comparison with a traditional superstructure demonstrated that this would be a cost effective alternative. The criteria used to determine the design of the residential structure was as follows: 1. The appearance should not be different then a typical three bedroom residence; 2. Only commercially available devices and present architectural and engineering technology should be used to achieve the required "flexibility" of the super- structure; 3. The structure as completed would be capable of resisting a predetermined amount of vertical and horizontal movement; and 4. If the structure was to experience stresses beyond its capabilities, it could be easily removed from the foundation and releveled.

Jan 1, 1986

By Patrick R. Taylor

United States Antimony Corporation, at its Yankee Fork property in central Idaho, is currently using a combination of flotation, gravity-amalgamation, and concentrate cyanide leaching, silver sulfide precipitation, and activated charcoal loading to recover both silver and gold. Tine processes of flotation, milling, gravity concentration, amalgamation, concentrate leaching, sulfide precipitation and gold recovery via charcoal are discussed. The flow sheet illustrates the use of cyanidation as an alternative to shipment to a smelter.

Jan 1, 1984

By Kerry Spickelmier

Editor's note: information for this feature was taken from the published APCOM proceedings. Computer trends, with special focus on the reasons for computer use, grabbed the lion's share of attention at the 23rd worldwide meeting on the Application of Computers and Operations Research in the Mineral Industry (APCOM 23). However, technical topics did not provide the meeting's sole focus. The last-minute inability of certain former communist countries to fund the travels of a few scheduled speakers was a reminder that science does not operate in a void. As with all technical progress, the APCOM presentations raised interesting questions regarding interrelated organizational dynamics and political and socioeconomic issues. Consider US Bureau of Mines (USBM) research to design an expert control systems to "duplicate" an experienced, "good" operator during automated underground roof bolting. In his presentation of the project, Takach, Jr. stressed the importance of preserving the ability to switch from automatic to manual drilling control. From a technical standpoint, this allows the expert system to "learn" from a good operator. As important, he said, is that this flexibility decreases the human operator's sense of being replaced by the machine. The question arises: Which will loom larger in union minds, increased operator safety through remote opera¬tion or the potential for total operator replacement? Like any new product, computer technology relies on marketing to aid its acceptance and use. Consider, too, a decision support system, by Schena and Gochin, for mineral resource management in a developing country. The authors said "the analysis permits the assessment of the overall socioeconomic consequences of mineral prospects and allows incorpo-

Jan 1, 1992

By W. H. Pomroy

In its 2001 diesel particulate matter (DPM) rule for metal and nonmetal underground mines, MSHA established an interim concentration limit of 400 micrograms of total carbon (TC) per cubic meter of air (400TCµg/m3), and a final concentration limit of 160TCµg/m3, to be phased in over five years. Following a court challenge to the 2001 rule, MSHA, industry and organized labor reached a partial settlement of the litigation under which the agency agreed to issue a proposal to amend the 2001 rule by, among other things, changing the surrogate from TC to elemental carbon (EC), applying MSHA's traditional hierarchy of controls, and revising requirements for one-year special extensions for complying with the final DPM exposure limit. MSHA issued a final rule in 2005 converting the interim concentration limit from 400TCµg/m3 to 308 micrograms of EC per cubic meter of air (308ECµg/m3) based on a miner?s personal exposure. Pending further rulemaking, MSHA retained the final concentration limit of 160TCµg/m3. In May 2006, MSHA issued a final rule that clarified that the final limit of 160TCµg/m3 would be based on a miner?s personal exposure rather than as a concentration limit. The 2006 rule also phased in the final DPM limit in three steps over two years, beginning in May 2006 at 308ECµg/m3, followed eight months later in January 2007 with a limit of 350TCµg/m3, and finally reaching 160TCµg/m3 in May 2008. Also in the 2006 rule, MSHA committed to converting the 160TCµg/m3 limit to an EC limit in future rulemaking. This paper reviews the DPM exposure limits in the context of the MSHA rulemakings and discusses the DPM engineering controls that were utilized by mine operators to attain compliance with each progressively lower limit.

Jan 1, 2009

By Alan S. Peck

Chemisorbed oleate films on the surfaces of fluorite, barite, and calcite were studied by means of infrared spectrophotometry. Evidence is presented which indicates the mineral anions, i.e., fluoride, sulfate, and carbonate, are displaced from the mineral surfaces as a result of the adsorption from aqueous solutions. Also, chemisorption reactions between oleic acid and fluorite or calcite occurred spontaneously in the absence of water. Carbon dioxide was identified as a reaction product when dry calcite was contacted with oleic acid. There was no evidence of reaction between oleic acid and barite in the absence of water.

Jan 1, 1964

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [ ] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m%-sec instead of meters. Adding the gravitational constant corrects this: [ ] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per sec). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [ ] References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 3, 1985

By J. C. Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult because a slope will transverse through many different types of strata. Over the past three years, Keystone Mining Services, LLC, an affiliate company of Jennmar Corporation, has developed a new methodology designated the ?Stress, Geologic, and Support Design System (SGSsm)?. This patent pending method analyzes the stress, geology, and support design for a mine slope. It has been successfully applied in various new slopes across the United States. This paper will detail the main concepts of the methodology including: (1) Analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) Primary and supplemental support design; (3) Long term support design in the form of steel square sets or arches, and (4) Validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By Alan H. Goode

Of the 15 million tons of glass discarded in municipal wastes annually, about 2 million tons pass through incinerators and can be recovered by ore processing techniques. Although the primary use for this recovered waste glass would be as cullet in the manufacture of new glass containers, this approach is not always practical because of long shipping distances, high freight costs, and high purity requirements. Alternatives to the use of waste glass as cullet would be either as landfill or in secondary products. Although glass is considered a good landfill material, it is still wasteful of potentially valuable raw materials. Secondary products that can be made from waste glass1 include a variety of industrial and construction items. As part of the Bureau of Mines' program in secondary materials recovery, the Tuscaloosa Metallurgy Research Laboratory has conducted research concerned with the development of ceramic building products from waste glass. Materials employed in this research were obtained from municipal incinerator residues fractionated in the Bureau's continuous residue processing plant, College Park Metallurgy Research center.' The studies reported herein3,4 present research results using waste glass in the formulation and production of clay bricks, not only to produce improved products, but to reduce production costs, conserve natural raw materials, and most important, to reduce manufacturing energy requirements.

Jan 1, 1974

By T. V. Shockley

The Gulf Coast, from New Orleans, Louisiana to Brownsville, Texas, is one of the largest high energy consuming areas in the United States. This region has areas of very high industrial density. The lower Mississippi River from Baton Rouge past New Orleans has a high industrial density. Lake Charles, Louisiana, the Orange-Beaumont-Port Arthur area, Houston (4 separate areas) and Corpus Christi all have the same high industrial density. This situation developed due to good transportation, good labor conditions, good weather and the abundance of cheap energy-gas and electricity. Obviously the latter had the greatest impact. The availability of cheap natural gas made Gulf Coast sites very attractive to energy intensive industry such as metals and petro-chemicals. The area was also very attractive to refinery development due to the large supply (endless?) of crude oil available. As we all know, the energy situation has changed dramatically in the last five years. The cost of a MMBTU has risen from the 17¢ to 19¢ level to a price of $1.95 to $2.10. The price of interstate gas, as defined by the National Energy Plan recently passed by Congress, was approximately $1.98/MMBTU escalated to October, 1978. It goes without saying, that this has had a major impact on doing business in the Gulf Coast. As fuel prices soared, different companies responded in different ways; but overall, industrial energy consumption along the coast was reduced 20% to 25% from 1974 to 1975. Since 1975 production and energy use has been increasing, however, production at some plants is still significantly below plant capacity.

Jan 1, 1979

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By Arthur W. T. Grimley

Hydraulic coal mining is being successfully practiced in China, U.S.S.R., Japan and Canada and in each country, excepting Japan where suitable sites are not available, the system is being expanded to either existing conventional mines or new mines. Productivity levels and economics at these mines are in all cases better than the productivities achieved in conventional mines in the same general localities. In the U.S.S.R. face productivities approaching 50 tons per man shift have been reported while in Canada the latest statistics show average face area productivity levels are in the region of 200 tons per man shift production monitor. In the United States hydraulic mining has not been actively pursued to the same degree and consequently there are no full scale hydraulic coal mines in operation or construction. Because many of the coal measures in the Western U.S.A. are generally somewhat similar to those being successfully hydraulic mined in Western Canada and parts of Siberia it is realistic to believe that successful hydraulic mines can be designed and developed in the Western U.S.A. Particularly if the vast technological base that already exists is used to improve on other people's ideas, systems, methods and equipment.

Jan 1, 1983

By M. C. Roberts

The success of any industrial mineral project requires an accurate forecast of the demand for the material. This paper develops a general method of evaluating these needs and applies it to the case of graphite. The basic method is to explain graphite consumption in each of its major uses by the output and manufacturing technology of the using industry. Once these underlying factors are determined, they can be projected to establish future requirements. This demand forecast is critical to the evaluation of a new source of supply, such as the graphite resources of upper Michigan.

Jan 1, 1989

By Y. Guo, C. Cao

"China is rich in tungsten resource, but they are mainly associated minerals. The similar flotability of scheelite, fluorite, and calcite resulted in the difficult separation by flotation. This work summarized the current situation and the development of flotation reagents, technological process, and mineral processing equipments in China. Fatty acid served as the collector and water glass was the depressant to expand the flotability differences in traditional flotation technology. However the water glass inevitably influenced the flotation of tungsten minerals to a large extend, and the suppressed fluorite was difficult to recover by flotation. Abundant water glass lead to the bad settleability of the tailings and the tail water was difficult to circulate, resulted in serious environmental problems. Recent study proved that the selectivity of benzene armour hydroxyl oxime acid (BAHA) salts was adequate for the separation of tungsten minerals from fluorite, calcite and most silicate minerals without any depressant. By this way, sodium silicate was canceled completely in tungsten flotation, greatly improving the recovery of tungsten and the environmental problems caused by tail water treatment would be solved fundamentally. TUNGSTEN RESOURCES AND DISTRIBUTION IN CHINA China is rich in tungsten resources and the proved reserves accounted for 60% of the world's reserves [1]. However the wolframite has been dried up and the scheelite resources had become the main resource of the tungsten metal. Table 1 showed the most large and superlarge scheelite deposits in China. China has more than 40 large and superlarge scheelite deposits and the total metallic deserves is more than 3 million ton [2]. But most of the deposits were low-grade and the associated relationship was complicated. For example, scheelite was usually associated with wolframite, molybonite, bismuthinite, pyrite, fluorite, and calcite in Shizhuyuan and Yaogangxian mine."

Jan 1, 2016

By VIVEK KASHYAP, EVODY TSHIJIK KARUMB, PATRICK TAYLOR

Zinc ferrite is considered an integral phase of zinc residues as their presence can render the processing of zinc and critical metals difficult. It is a refractory phase, formed at high temperature in the presence of zinc (Zn) and iron (Fe) during oxidative roasting in zinc processing plants. Because it is refractory to efficient leaching, unreacted zinc ferrite gets concentrated in the final zinc residue, making it a viable source of zinc and indium extraction. The refractory nature of zinc ferrite makes the extraction of associated critical metals difficult. In order to explore a potential economic and carbon-neutral zinc ferrite processing technique, our previous study proposed the partial reduction of zinc ferrite followed by sulfuric acid leaching of the roasting product [1-3]. As demonstrated in our previous studies, partial reduction of zinc ferrite results in a mixture of ZnO, Fe3O4 and FeO, which can be further subjected to leaching for efficient extraction of zinc and critical metals such as gallium and indium.

Dec 1, 2022