Search Documents

By H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothability tests and SEM observations. In the absence of sodium silicate, Ca++ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: (1) the removal of impurity minerals and calcium-bearing. precipitates from quartz surfaces by dispersion, (2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and (3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1990

By S. Acar, M. Botz

Introduction In 2007, Newmont Mining Corporation will begin construction of a milling and cyanidation leaching circuit for the Yanacocha site in Peru. Ore to be processed in the circuit contains a relatively high level of cyanide-soluble copper, and as a result, leach solutions are expected to contain elevated levels of copper and WAD cyanide. As the means of controlling copper levels in leach solution, a circuit will be installed to precipitate copper sulfide from barren solution using sodium hydrosulfide. In addition, a circuit will be installed to recover cyanide from barren solution, with recovered cyanide to be returned to the leaching circuit and treated solution to be utilized as make-up in existing heap leaching facilities. As needed to support design of the copper precipitation and cyanide recovery circuits, pilot testing was conducted in 2005 to determine preferred operating conditions and evaluate the performance of the processes. This paper presents results from the pilot testing where 99% copper reduction was achieved and 95% to 98% cyanide recovery was achieved.

Jan 1, 2007

By C. A. Rowland

Autogenous grinding, defined as grinding with like material, while quite an old art has recently been revitalized. Two phases of autogenous grinding, primary and secondary, have been the subject of recent papers, technical articles and discussions. The purpose of this paper is to discuss a third phase of autogenous grinding - Intermediate Autogenous Grinding - comparing it to and indicating advantages over the other two phases. Autogenous grinding can also be called ?Rock grinding?1; that is, grinding using ore or rock from the same deposit as the mill feed as grinding media contrasted with using as grinding media steel rods, steel or ironballs, natural or manufactured iron, free pebbles, or other shapes and materials foreign to the mill feed.

Jan 1, 1964

By Thomas S. Nye

Mineral exploration in the United States relies heavily on theoretical geologic concepts and indirect methods such as geophysics and geochemical prospecting, as there are few exposed areas of mineralization which have not already been explored at least once. In Mexico ore-grade samples can be cut at the surface on vein, replacement, and disseminated types of deposits in many areas. Here the problem is not in finding a mineralized area but in deciding which mineralized area can be explored and developed at the least risk and cost, and have the greatest profit potential, within the framework of Mexican mineral economics and government policies. Mexico's min¬eral industry is regulated through a system of permits for various phases of mineral exploitation, and by taxes. This regulation and its effects are not unlike those which may be expected in the United States if present legislative and administrative trends continue.

Jan 1, 1972

By Timothy P. Smirnoff

Sustaining the region?s mobility needs, achieving projected economic growth, and maintain Midtown Manhattan as a center of regional, national and global importance has led to continued investment in commuter rail and transit infrastructure in New York City and resulted in design and construction of large underground caverns. The current plans for stations in Manhattan include New York Penn Station Expansion (NYPSE) caverns for Trans Hudson Express (THE) Tunnel Project for New Jersey Transit (NJ Transit) and the Port Authority of New York and New Jersey (PANYNJ), Metropolitan Transportation Authority Capital Construction Long Island Railroad (MTACC/LIRR) twin caverns for East Side Access (ESA) Project, and station caverns of the No. 7 Line Subway Extension Project and Second Avenue Subway Project for Metropolitan Transportation Authority Capital Construction/New York City Transit (MTACC/NYCT). This paper provides a general overview of these large caverns now in design or construction in Manhattan, the area?s geologic setting, the geotechnical factors considered and approaches commonly applied for cavern design.

By W. D. Mayercheck, A. G. Mayton, J. R. Bartels

Abstract-Since 1982, the US Bureau of Mines has inves¬tigated improvements in protection for operators of thin seam shuttle cars. Due to working height restrictions in thin seam mines (<_1.22 m or 48 in.). Federal mine regulations require that canopy protection on shuttle cars he provided only in mines >_1.07 m (42 in.). However, court obtained variances are granted to mines <_1.22 m (48 in). This paper presents ongoing research to design and evaluate a uniquely positioned, ergonomic compartment for a shuttle car that provides the operator with full canopy protection in working heights of 1.02 m (40 in.).

Jan 1, 1989

By Rollien R. Wells

The Bureau of Mines was created in 1910 by an act of Congress and subsequently directed to: "...conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment, and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources through the prevention of waste ..." Under this broad charter, the Bureau&apos;s responsibilities have changed and grown from an almost exclusive concern with coal and coal mine safety to the present emphasis on a full spectrum of mineral producing and consuming problems. In the past 30 years, the domestic consumption of coal, oil, gas, metals, and industrial minerals has more than quadrupled, in parallel with the rapid and enormous growth in industrial production. Of the scores of metals and nonmetals essential to the Nation&apos;s progress and security, many are scarce and difficult to wrest from domestic sources. Reserves of some ores are dwindling. Available ore resources are becoming leaner and more difficult to treat. In recognition of this many faceted problem, the Bureau has engaged in a continuing quest for new and improved technology to enable economic exploitation of marginal minerals and fuels, to find substitutes for minerals in short supply, and to create better materials to meet the expanding and diverse requirements of the growing economy. The current central concern of the Bureau is focused on meeting projected fuel, metal, and mineral demands at the lowest real cost by recovery from available resources by new and improved technology that minimizes waste, hazards, and social and environmental problems.

Jan 1, 1970

By Helmut Westermayr, Michael Tergl

DESCRIPTION OF PROJECT Geographic Setting The Kops II plant is a pumped storage scheme of the hydroelectric power producer ‘Vorarlberger Illwerke AG’ which is currently under construction in the Austrian Province of Vorarlberg. The plant is located at the end of the Montafon valley and will be fed with water coming from the Silvretta mountain range (Figure 1) Description of Plant The Kops II plant shall be operated as a pumped storage plant with three highly flexible and quickly controllable power generating units. Each unit shall have a capacity of 150 MW and shall be equipped for both turbine operation and pump operation. The Kops II plant uses the existing Kops Lake as upper storage reservoir and the existing Rifa balancing reservoir as lower storage reservoir. All major plant components of the Kops II scheme are located below ground. Total investment costs areapprox. 360 million Euro. Construction Lots The construction works for the Kops II plant, which were subdivided into three lots, were launched in September 2004. It is planned that the first power generating unit shall go on line in the year 2007. The completion of the overall project and the operation start-up of the second and third unit are envisaged for the year 2008. Lot 1—Pressure Tunnel. The 5.5-km-long pressure tunnel forms the connection between the Kops Lake and the beginning of the pressure shaft. The tunnel was excavated by the use of a double-shield TBM. Lot 2—Pressure Shaft and Surge Chamber. The approx. 1.1-km-long pressure shaft was excavated by TBM, advancing from bottom to top. Featuring an inclination of80%, the pressure shaft overcomes a difference in height of approx. 700 m. Lot 3—Power House Cavern and Tailrace Structure. The power house cavern, which is being built approx. 150 m inside the mountain, forms the core of this plant. The power house is designed to accommodate three power generating units, and the transformer cavern is forseen to accommodate three transformer units. The tailrace structure serves the purpose of conveying the water to the lower storage reservoir during turbine operation and as water intake during pump operation (Figure 2).

Jan 1, 2007

By J. M. Rebstock

Recent re-classification of crystalline silica as a potential human carcinogen has resulted in a new limit of 0.1% free silica in bulk powdered minerals. Detection of silica at this level can be expected to severely challenge or exceed the capabilities of existing protocols for x-ray diffraction, the traditional method for free silica determination. Automated SEH-EOS analysis provides an attractive alternative method, with direct analysis of individual particles for the determination of the concentration of free silica, and a direct measurement of silica particle sizes. This paper will discuss automated SEH analytical procedures, sample preparation, and statistical considerations.

Jan 1, 1990

By C. Treworgy, C. Chenoworth

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Feb 24, 1997

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By B. L. Bobo

To ensure the continued growth and economic viability of the Western coal industry, both in the domestic and inter- national markets, it is essential for the industry to become more creative and active in confronting the most serious obstacle in this objective; and that is, the inherently long distances which Western coal must be transported inland to reach its major markets. Figure 1 shows the 1982 coal consumption by state for those states where Western coal was consumed. (Except as noted in this paper, Western coal producing states are defined as Colorado, New Mexico, Arizona, Utah, Wyoming, Montana and North Dakota. Any exceptions used will have only an insignificant effect on the content of the paper). This figure illustrates the long distances that are required for Western coal to reach its markets. The total production for 1982 from the Western coal producing states was approximately 220 million tons, of which only 85 million tons was consumed within the boundaries of these states. The remainder was transported to markets outside the area. This map also shows, based strictly on the consumption of the states to which Western coal was shipped during 1982 and not considering other factors which are involved in the marketing of coal, the total market potential of Western coal would amount to a total of 445 million tons. This does not include export coal from the West Coast, which is now estimated to be less than 2 million tons for 1983. In 1980, it had been estimated that by 1985 the West Coast exports would have been at least 10 million tons per year, which will not be attained.

Jan 1, 1983

By R. R. Klimpel

During the period of 1973-79, an extensive period of research and development was undertaken by Klimpel and coworkers (1980, 1981, 1982a, 1982b, 1983. 1984, 1987) on the identification of a commercially viable chemically assisted approach to improving the efficiency of the wet grinding of coals and ores in tumbling media mills. The emphasis of the previous publications just listed was on the engineering use implications of controlling-slurry viscosity (rheology) in laboratory and plant scale grinding devices. In this paper, some discussion and results pertaining to the actual chemical screening phase will be presented.

Jan 1, 1988

By R. Woods

"Comments on the paper ""Formation of hydrogen peroxide by chalcopyrite and its influence on flotation,""by A. Javadi Nooshabadi and K. Hanumantha Rao (Minerals & Metallurgical Processing, 2013, Vol. 30,No. 4, pp. 212-219)The formation of hydrogen peroxide from water during the grinding of chalcopyrite in a nitrogen-sparged environment, as reported by Javadi Nooshabadi and Rao (Minerals & Metallurgical Processing, 2013, Vol. 30, No. 4, pp. 212-219), is questioned on the grounds that oxidation of water by the mineral is unlikely to be thermodynamically feasible. It is argued that it is more likely that any peroxide that had been formed would have been generated from residual oxygen in the nitrogen-flushed system than from the oxidation of water.The formation of hydrogen peroxide by finely divided pyrite had been reported by a number of authors (Borda et al., 2001; Borda et al., 2003; Cohn et al., 2006; Schoonen et al., 2006; Schoonen et al., 2010; Jones et al., 2011; Javadi Nooshabadi et al., 2013). That hydrogen peroxide is formed in the presence of oxygen in solution can be comprehended from wellestablished mechanisms. Pyrite in aerated solution is known to oxidize by an anodic process that is coupled with the cathodic reduction of oxygen (Holmes and Crundwell, 2000). The latter process has been shown to occur through the formation of hydrogen peroxide (Biegler et al., 1975; Ahlberg and Broo, 1996). The pH dependence of cathodic oxygen reduction at other sulfide minerals, including chalcopyrite (Biegler et al., 1977; Rand, 1977), implies a similar mechanism at these surfaces."

Jan 1, 2015

By K. Ananthpadmanabhan

Hydrolyzable surfactants such as fatty acids and amines undergo, in addition to micellisation and precipitation, various associative interactions in aqueous solutions to form ion molecular complexes such as acid-soap, dimers etc. depending upon the solution conditions such as pH. The interaction of these collector species with the mineral surface and with other dissolved species in solution will play a significant role in determining the interfacial processes such as adsorption and flotation. Marked differences in the hydrophobicity imparted to the mineral surface depending upon the solution conditions such as Ph can be attributed to possible differences in surface activities of the above complexes. This aspect of solution chemistry of flotation systems is discussed here for two widely used collectors namely, oleic acid and dodecylamine. Equilibrium species distribution diagrams based on the available literature .data and on estimates of energy of interactions between molecules, have been obtained for oleic acid and dodecylamine solutions.

Jan 1, 1978

By Clyde N. Garman

Historically, Vanadium and Uranium have been precipitated together in carbonate sill circuits. A separation of the salts of the two metals was then made on the basis of the fact that the reduced, salts of vanadium are more solo to and those of uranium lose soluble than the respective salts of higher valence. In practice this was carried out by fusing the precipitated combined concentrate with salt, sodium carbonate and sodium hydroxide with oil soaked sawdust mixed into the charge as the reducing agent. Generally the fusion was carried out batch wise and the resulting slag or glass leached in water. A good, fusion and three or four decantation washes resulted in almost complete recovery of the vanadium in the liquid phase and a very high recovery of the uranium as a dense black U02 solid.

Jan 1, 1962

By Duncan M. Lamb

Commercial computer "time-sharing" is a new and powerful tool for the engineer. It is a system of virtually simultaneous use of a digital computer by several individuals. Access to the computer is by means of a conventional teletypewriter which transmits over the regular telephone lines to the computer which may be located any distance from the user. Complex or repetitive computations can be programmed and the speed of computation is many times that which one can do with slide rule and desk calculator. The availability of such a commercial computer "time-sharing" system offered an opportunity to transform a tedious and time-consuming task into one that requires only a few minutes. Until the work of F. C. Bond produced widely accepted mathematical statements concerning the performance of grinding mills, the selection of the proper size equipment was done by comparison with similar operating equipment. Allis-Chalmers systematized Bond&apos;s work in a bulletin published in 1963 but the calculations are laborious and the final mill selection still required comparison of the calculated power draw with the power requirements listed in equipment catalogs. This was, however, a step forward from previous procedures. This paper discusses a rapid and simple method of determining the size and power requirement of overflow ball mills. A shared-time computer program has been developed which rapidly calculates and displays the physical dimensions, power requirements, grinding media size and quantity, as well as the important correction factors used. All of these data are calculated from input information which is usually available.

Jan 1, 1969

By Randal J. Barnes, Franck Rellier

Mine ventilation survey data includes generally redundant, usually inconsistent, often incomplete, and always noisy measurements. Yet, these data are essential for operational decisions and represent the foundation of any mine ventilation systems model used for future engineering analysis and design. For example, the basic ventilation network geometry can be measured with a reasonable precision, the network flows can be measured, but with significant errors, and the branch resistance factors can not be directly measured at all. The network-based, constrained weighted least squares approach, presented in this paper, advances a method for the sys tem-wide adjustment of ventilation branch measurements and the consistent estimation of global system parameters (e.g. branch flows, head losses, and resistance factors). The constraints guarantee that the adjusted values satisfy the governing physical laws: conservation of flow, conservation of energy, and the appropriate energy dissipation rule (e. g. Atkinson&apos;s RQ2). The weights allow for the proper inclusion of data with widely disparate precision, as well as offering a simple method for retiring old data as the mine changes through time. The post-adjustment sensitivity analysis presents two potentially useful forms of analysis: the identification of previously unspecified leakage branches, and the semi- automatic recommendation for future ventilation measurement campaigns. The overall efficiency of the algorithm is exemplified by the fact that a ventilation network with hundreds of branches and thousands of measurements can be routinely adjusted on a microcomputer.

Jan 1, 1989

By Johann Engelbrecht, Stéfan de Bruyn, Petrus van den Heever

A system for the on-stream X-ray diffractometric determination of mineral phases in slurries was developed in response to the mining industry&apos;s need for process control during the beneficiation of industrial minerals. The instrumentation for and results from testwork conducted at a phosphate rock beneficiation plant in Florida are discussed. Results show that the concentrations of the minerals apatite (var. francolite) and quartz can be accurately determined every few minutes, so that adjustments to the flotation circuit can be timeously executed from the control room. The on-stream measurements can ultimately be integrated into an automated plant control strategy. Estimates of savings on reagent and staffing costs, as well as the benefits from consistent grades and greater recoveries, have shown that the investment in such a system could often be recovered in less than a year.

Jan 1, 1999

By J. M. Hans, M. F. O’Connell, G. E. Eadie

INTRODUCTION The U.S. Environmental Protection Agency (EPA) was required, under Section 114(c) of Public Law 95-604, to provide a report to Congress identifying the location, and potential health, safety and environmental hazards of uranium mine wastes together with recommendations, if any, for a program to eliminate the hazards. The approach taken to prepare the report was to develop model active and inactive mines and locate them in a typical mining area to estimate their environmental impact. A list of uranium mines was acquired from the U.S. Department of Energy (DOE). The inactive mines were separated from the list and sorted into surface and underground categories. A literature search was conducted to obtain and consolidate available information concerning the environmental aspects of uranium mining and shortterm field surveys and studies were conducted to augment this information base. Radioactivity emission rates were measured or estimated for each mining category and were entered into computor codes to assess population exposures and subsequent health risks. The general environmental condition of inactive uranium mines was determined by walk-through surveys in several mining areas. INACTIVE SURFACE MINES We assumed that a model inactive surface mine contains a single pit with the wastes (overburden and sub-ore) stacked into a pile adjacent to the pit area. No credit for reclamation is given to the model mine. In lieu of the availability of individual mine production statistics, the model surface mine size was established from the total ore and waste production statistics for all surface mines, divided by the number of inactive surface mines. The number of inactive mines, obtained from the DOE mine listing, are summarized by type and location (Table 1). For modeling, we assumed that there are 1,250 inactive surface mines. The total or cumulative waste and ore production for inactive surface mines from 1950 to 1978 is not fully documented. Uranium mine waste and ore production statistics, on an annual basis, were available for both surface and underground producers from 1959 to 1976 (D0159-76). Annual uranium ore production for each uranium mining type are available for 1948 to 1959 (DOE79) and for combined ore production TABLE 1. Consolidated list of inactive uranium producers by State and type of mining [State Surface Underground AL 0 9 AZ 135 189 CA 13 10 CO 263 902 ID 2 4 MT 9 9 NV 9 12 NJ 0 1 NM 34 142 ND 13 0 OK 3 0 OR 2 1 SD 111 30 TX 38 0 UT 378 698 WA 13 0 WY 223 32 Total 1246 201T] for underground and surface mining from 1932 to 1942 (DO132-42). In order to estimate waste accumulated prior to 1959, the waste-to-ore ratios from the 1959 to 1976 period were plotted vs. time and line-fitted by regression analysis (Figure 1). Unfortunately, the extrapolation of the line to years prior 1959 approached zero in 1954 although surface mining began in 1950. Therefore, a waste-to-ore ratio of 8:1 was used for the period of 1950 to 1959 based on ratios estimated by Clark (C174). The waste to-ore ratios for 1976 to 1978 were estimated using the line established in Figure 1. By using waste-to-ore ratios and ore production data, the cumulative waste and ore production for both surface and underground uranium mining is estimated to 1978 (Table 2). The estimated cumulative waste from uranium surface mining for 1950 to 1978 is 1.73 x 109 MT. A crude estimate of the waste accumulated at the model inactive surface mine can be made by dividing the total waste produced to 1978 by the number of inactive mines. This, however, overestimates the waste tonnage because some of the contemporary wastes are being produced by active mines, and the waste accumulated at newer mines has increased in recent years. To adjust for this overestimate, we assumed that all mines operating in 1970 will be inactive by 1978. This eight year period is approximately one-half the lifetime of a model

Jan 1, 1981