Search Documents

By J. G. Groppo

A beneficiation process has been developed to provide selective separation of unburned carbon from high loss-of-ignition (LOI)fly ash. Using froth flotation to achieve selective separations requires long residence times and high reagent costs. A proprietary reagent system has been developed to address these limitations. Based on the results obtained from laboratory and pilot-scale investigations, a flowsheet design has been developed to produce two distinct usable products from class F fly ash — low LOI ash and a high-carbon product suit-able for reburning or further upgrading.

Jan 1, 1996

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By Qinghua Song, Jianhong Chen, Shan Yang, Zhiyong Zhou

"The development process of Metal Resources Technical and Economic Evaluation Expert System (MRTEEES) is introduced in the aspects of requirements analysis, design of the expert system, main functions of the expert system and features of the expert system. The system is based on C/B/S mixed mode and uses ASP.NET technology with .Net Framework being chosen as the development platform and metal resources database providing data support at the bottom layer. The system is an auxiliary management system for metal resources technical and economic evaluation and has the basic functions of auxiliary decision analysis, metal resources database management, data management and comprehensive query. Technical and economic evaluation model can be set up by users independently according to at which stage a project is, mainly including exploration stage, development stage and production stage, and according to the mining methods, for example underground mining, surface mining and in-situ leaching mining. Then, the technical and economic evaluation parameters can be generated. By inputting the value of each parameter in a simple and convenient way, the evaluation results can be directly calculated out and shown in the form of diagrams among others, and feasibility evaluation report can also be automatically generated, making the technical and economic evaluation process accurate and efficient. As the system can achieve the functions of scenario analysis, sensitivity analysis, shareholder’s returns analysis, horizontal comparison of different projects, it can improve the ability of project senior decision makers for rapid response to the rival and meet the demand of pricing negotiations. IntroductionWith the arrival of a new round of industrialization upsurge in both developing and developed countries, growth of demand for metal resources is entering a new stage. Population involved in the new industrialized countries is about four times that of all previous industrialized countries, implying resource consumption increases dramatically both in speed and in quantity. It is a must to seize the strategic opportunity of developing and utilizing metal resources around the world to lay abundant resource base for national industrialization. Objectively speaking, global configuration of metal resources is an inevitable tend. Presently, many issues, for example, resources exploration, mining, merge of mining companies, metal trades, mining financing, etc., generally show the feature of globalization. For the reality that competition for metal resources is becoming fiercer, industry standards of mineral resources will undoubtedly be improved. Occupying large scale mineral resources with high grade and developing them with low cost is the base for the survival of mining companies and metal resources merchants. With the growing demand of global investment in mineral resources exploration, which is at the upstream of the industry chain, geological exploration industry is promising. Globally building market relationships for mineral resources exploration companies is key to their sustainable development. Developing large and super-large deposit with low cost is also an important approach to enhancing core competence of a country or an enterprise. Mining companies around the world are rushing to purchase mineral resources globally. However, in different countries, economic, financial and tax systems for mineral resources vary greatly, and mining and processing techniques, technical parameters and equipment selection also change a lot. Thus, pro-phase research work is necessary for feasibility evaluation of mineral resources projects and it can be time wasting if taken in the traditional way. It is necessary to accelerate the process considering the complex and rapidly changing international situation."

Jan 1, 2017

Sweden is beginning to reap the rewards of a process that has transformed a country with a history of metal mining into one of Europe's most vibrant exploration regions. Exploration and mining companies from North America, Europe and Australia have joined local firms in the search of gold, base metals and diamonds. This has been due to changes in Sweden's mining laws in the early 1990s. These changes opened the way for unhindered private sector investment in the country's mineral industry. More than 20,000 km2 (4.9 million acres), mainly in northern Sweden, is now held under granted or applied exploration claims. Exploration permits diamonds, applied or granted covers more than half of Sweden's surface. This is a greater proportion of the country than ever before. Major mining companies and junior explorationists are evaluating a geological potential that bears favorable comparison to other major mining centers. Historically, Sweden's gold re- sources occur in greenstone belts in northernmost Sweden and in association with massive sulfide deposits in the Skellefte district. These are receiving particular attention by exploration companies. In addition, new areas in Sweden are also being explored for gold. This increases the probability that Swedish gold production - already the highest in Europe - will increase in the future (Table 1). Sweden's recorded mining history goes back for much of the last large pool of expertise in exploration, mining, equipment manufacturing and minerals industry research. In addition, the Geological Survey of Sweden provides sup- port for exploration in terms of data archives, processing and publications. Other benefits for exploration companies are Sweden's communications infrastructure, its member- ship in the European Union, bringing access to one of the world's major markets and the high level of educational, technical and language skills held by the country's work- force. And deregulation of the economy and the introduction of competitive corporate tax rates have made Sweden a favorable destination for investment in Europe.

Jan 1, 1997

By Tae-kyeong Yeu, Jong-Choi, Cheon-Hong Min, Hyung-woo Kim, Jae- Won Oh, Sup Hong, Minuk Lee, Sung-Soon Kim, Chang-Ho Lee, Ki-Young Seong

"Collecting mineral resources from the seabed using a seafloor crawling robot is the firststep in the mining operation. The second-step is lifting the collected ore up to the water surface. For lifting through a riser pipe, prevention of pipe clogging (flow assurance) and economic and eco-friendly up-transferring is of the utmost concern.During collection of mineral ores, the production rate can be highly variable because of the variability in the distribution of the mineral deposit, variations in seafloor topography, fluctuations robot speed, and variations in performance of the mining robot, etc. Direct transfer of the collected ore to the riser pipe might cause unpredictable and serious problems such as over-loading of the lift pump, reduction in the life of the equipment, pipe clogging, severe increase of down-time, critical damage of equipment, further propagation of damages, and total failure after all.As a counter measure to these potential problems, a buffer station has been adopted, which is capable of storing the collected ore for a certain time and simultaneously regulating the transfer of the ore into the riser pipe. A pilot buffer has been developed by KRISO/KIOST (see Fig. 1)."

Sep 1, 2014

By J. P. Wilson

The Tessenderlo-Kerley Leach process has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia and ammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By Paul F. Gnirk, Ralph A. Wagner, Joe L. Ratigan

This thermomechanical analysis used the finite element method to investigate the behavior of crushed salt backfill in a waste disposal room situated in a salt dome repository. The first of two objectives was to determine the transient temperature rise and degree of thermomechanical consolidation that occur in the backfill as a function of drillhole depths. The second objective involved the evaluation of closure due to salt creep of unlined emplacement drillholes and the determination of pressure on steel sleeve liners in the drillholes should liners become necessary for canister retrieval. The retrievability period was considered to extend for 25 years after waste emplacement. The canisters were assumed to contain ten-year old high level waste with a thermal output of 4.3 kW at the time of emplacement.

Jan 1, 1981

By Mehmet Guney

During the last decade various modifications of room and pillar and sub-level methods have been tried in an effort to eliminate gob-fires, dangers from roof falls, surface subsidence and to increase efficiency of extraction in the Armutcuk Mine, Turkey. It was eventually decided that the most likely system to give maximum benefits in view of existing geological conditions and coal seam characteristics was a system of cut-and-fill stoping employing hydraulic stowing. This paper has attempted to examine the trends of working techniques of hydraulic stowing. In addition, the results achieved and technical problems involved are discussed.

Jan 1, 1968

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By G. Potts, K. Raiber, T. BoBo

Effective control of balling line circuits is a problem taconite companies have been dealing with for over thirty years. The sensitivity of balling circuits to changes in moisture, bentonite, concentrate particle size, and other operating parameters are the main reasons for control problems. This paper presents test results and describes the integration of existing instrumentation with a digital image analysis system on a balling circuit. This work has the goal of developing control strategies to automatically adjust water spray and bentonite addition, to optimize the size distribution on the roll screen and reduce the variability in control between balling attendants, resulting in more consistent greenball product quality.

Jan 1, 2003

By Weston Bourret

The need for wartime supplies of uranium for the Manhattan Project prompted a 1944 study of uranium in South Africa. Uraninite had been reported by R.A. Cooper in 1923 in a Witwatersrand heavy- mineral concentrate, and the search for uranium, therefore, included the district's 30 operating mills. The method of investigation was simple: take bulk concentrate samples from the Wifley tables and determine their mineralogy. Samples were taken on a daily basis, although weekly composites also were taken of some mills. In 1944, most mills had simple gravity circuits and produced (I) a gravity concentrate, and (2) an all-slime [-75 pm (-200 mesh)] product. The tonnage throughput was known, and from that, head assays could be calculated. Concentrate samples were sent to the United States for chemical analyses. A Geiger counter set up in a Johannesburg hotel room provided preliminary data. The early data showed uraninite to be widespread. Microscopic, mineragraphic, and siezing tests were all under- taken in Johannesburg. Ultimately, tests led to a high grade (+90%) uraninite concentrate. Platinum and other heavies were the impurities. In seven months, the investigations had reached the stage where it was possible to forecast an annual production of 5.4 to 7.3 kt (6,000 to 8,000 st) of U3O8. The estimate is still realistic. Additional details are found in Bourret (1981).

Jan 1, 1991

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation's high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995

By J. Stoll

In May 1998, Hanson Aggregates Midwest, as an outcome of mine planning, offered a 10-acre tract of land containing the famed fossil-bearing Silica formation, to the City of Sylvania, OH. in the form of a 99-year lease agreement. The Olander Park System, and Ohio code park operating within Sylvania Township, was then approved by Hanson and the City to manage and fund the park. All parties signed the lease in August of 1999. In November 2001, local residents voted to fund the park by a margin of 2 to 1. The park will consist of a shallow (approx. 20 ft.) former cement production quarry that is 700 ft. long by 300 ft. wide. Hanson’s motivation and vision for the park was fivefold: 1) the site was located away from long-term reserve access; 2) it would serve nicely as buffer property for the active quarry; 3) it had become an area of illegal dumping by locals in the past; 4) trespassing and safety issues would be limited by allowing supervised usage; and 5) the shallow outcropping contains the world famous, fossil-bearing Silica shale. Hanson will supply shale to the park perpetually via stripping activities in the process of uncovering quality construction aggregate limestone and dolomite reserves. Thousands of enthusiastic fossil hunters have already combed throughout the shale in their quest for “treasures”. The park’s master plan also features nature trails, picnic areas, a fossil-themed play area, amphitheater, visitor’s center and gift shop. Given the natural and people resources that Sylvania Fossil Park will have to offer, Hanson is confident that it will become the premier invertebrate fossil hunting site in the United States. It will also remain a solid community relations vehicle for years to come.

Jan 1, 2003

By P. Somasundaran, F. F. Aplan

The Formative Years Douglas Winston Fuerstenau was born December 6, 1928 in Hazel, SD to Edwin Arnold and Hazel Pauline (Karterud) Fuerstenau. His father, of German extraction, was a farmer and, later, a cabinet maker, while his mother, of Norwegian lineage, was a school teacher. His parents are still alive today at ages 91 and 88, respectively. Two younger brothers, Richard and Maurice and a sister, Jean, completed the family. The family first lived near Watertown and later in Lemmon and Mobridge, SD. The 1930's were a difficult period for any family in South Dakota. A decade-long drought made this a part of the dust bowl, which together with a serious infestation of grasshoppers (the locust plague described in The Bible), and the world-wide depression, made living difficult for all. In spite of these privations, Doug has many happy memories of his childhood which can be attributed to the resilience of youth and a strong family structure. He has fond memories of summers spent with his cousins on family farms where the children were introduced to farm chores at an early age. When he was old enough, he worked in a grocery store after school. At the age of 14 he spent the summer hearding 2,000 sheep near Lemmon, SD as his contribution to the war effort in that labor-short period. He remembers well the dust storms of the 1930ts, the destruction at his grandmother's farm by tornado, pulling weeds on the farm, threshing grain with a monstrous steam-driven machine and such pleasant childhood activi- ties as fishing for bullheads, hunting for rabbits, searching for arrowheads in newly plowed fields, and ice skating in the winter. Early in life his parents instilled in him a strong work ethic, a love of learning and the need for a good education. In 1943, the family moved to Rapid City, SD. With a population of 13,000, it was

Jan 1, 1989

By Leonidio Stegmiller

Since the petroleum crisis in 1973, charcoal1 is being considered one of the most important fuel for the Brazilian consumers, mainly for pellet's producers. In replacing fuel by charcoal mixed up with ore, obviously one of the first thing to be investigated is its influence in the product's quality. Special attention has been given to the metallurgical characteristics. This paper infocus the effect of increasing dosings of charcoal to the pellet's porosity and how other physical and metallurgical characteristics will be affected accordingly. This work was carried out using two different finesses of charcoal and dosing varied from 0.5 to 2.0%.

Jan 1, 1982

In Alaska?s southwest corner, in the Bristol Bay region, 476 holes have been drilled to help define the size of the Pebble Project. The results indicate that the deposit holds close to 32 Mt (72 billion lbs) of copper and 2.9 Gt (94 million oz) of gold. The Pebble Partnership, an Alaskan limited partnership of Anglo American and Northern Dynasty Minerals, owns the project that consists of two world-class mineral deposits. Currently in the prefeasibility and prepermitting stage of development, the Pebble Project is one of the largest and highest profile exploration projects in North America. History The Pebble West Project was originally discovered in 1988 by Cominco (now Teck Cominco). Drilling programs in 1997 defined a near-surface mineral deposit of 1 Gt (1.01 billion st). Minerals found included copper, gold and molybdenum. Northern Dynasty Minerals acquired the property in 2001 and, by 2005, it had confirmed a measured and indicated resource of 4.1 Gt (4.5 billion st) containing 1.2 kt (42.1 million oz) of gold, 11.2 Mt (24.7 billion lbs) of copper and 612 kt (1.35 billion lbs) of molybdenum and additional silver. By September 2005, Pebble East, a deeper, but richer deposit had been found. Drill data by the end of 2005 confirmed a 3.4-Gt (3.7-billion st) inferred resource containing 19 Mt (42.6 billion lbs) of copper, 1.2 Mt (39.6 million oz) of gold and 1.2 Mt (2.7 billion lbs) of molybdenum.

Jan 1, 2009

By S. J. Aparo

Phosphate mining and beneficiation in the State of Florida are presently being carried on by 12 different mining companies with a total of 21 mining and flotation plant locations. Their combined production of both washer rock and flotation concentrate was approximately 28,000,000 long tons in 1968. This accounted for 70-72% of the total U. S. production and close to 30% of the world's output of this mineral. From this extensive activity in the Florida phosphate field, one basic flow sheet for beneficiation of the ore has developed over the years as the most commonly employed. In fact, all of these plants with the exception of two beneficiate Florida pebble phosphate using a basic operation as illustrated in Figure I. The two plants which differ from this general approach are not using raw matrix as feed. In one instance, +14 mesh pebble is ground in a rod mill to release free silica which is subsequently removed in a cationic froth flotation circuit using an amine acetate blend and kerosene. This technique generally results in a 4-7 BPL unit upgrading of the feed pebble. The other exception to the standard flow sheet illustrated in Figure I is an operation which is beneficiating tailing piles. In this case, the material is first subjected to cationic froth flotation in order to upgrade the feed to a point comparable to normal matrix. Thereafter, after, the phosphate is floated in an anionic rougher circuit followed by cationic flotation of the silica in a cleaner circuit.

Jan 1, 1969

By Jimmy Thompson

The Santa Clara Valley Transportation Authority is designing the Silicon Valley Rapid Transit Project in San Jose, California. The project includes 6.9 km (4.3 miles) of twin-bored tunnels to be constructed through downtown San Jose using two earth pressure balance machines (EPBMs). This paper begins with a project description and update of the project status followed by a description of the relationship between anticipated ground conditions and EPBM requirements. Topics addressed include soil conditioning, abrasion resistance, annulus grouting, face pressure estimation, additional pressure control devices and control measures to limit over-excavation and settlement.

Jan 1, 2008

By T. L. Myron

To determine the effect of flux crystal size on the production rate and strength of sinter, batch sintering tests were conducted on samples of both dolomite and limestone of various crystal sizes. In addition, calcination tests .were performed on the dolomite and Limestone to determine the effect of crystal size on calcination rate at various temperatures normally attained in sinter beds. The results indicate that flux crystal size does not affect sinter production rate or sinter strength.

Jan 1, 1962

By A. Yazadni-Chamzini

Maintenance strategy selection plays a significant role in mining design. The nature of maintenance strategy selection is a complex multi-criteria decision making (MCDM) problem including both tangible and intangible parameters which are often in conflicting with each other. Moreover, when decision makers are uncertain in determining and defining the ratings and the weights of alternatives and criteria respectively, fuzzy theory provides an appropriate tool to handle the existing uncertainties. In this paper, a new fuzzy MCDM method based on the concepts of TOPSIS and AHP was proposed to evaluate the feasible maintenance strategy. The linguistic terms are employed to assess the ratings and weights. Fuzzy AHP is utilized to calculate the weights of the evaluation criteria; then, the rankings of alternatives are computed based on fuzzy sets theory and TOPSIS. A real world case study is presented to illustrate a potential application of the proposed model.

Jan 1, 2012