Search Documents

By B. K. Belle

The use of diesel engine locomotives in South African mines can be traced to Van Dyk Consolidated Mines Ltd on the Witwatersrand gold mines in 1928 as a replacement for battery locomotives. The advantages and disadvantages were recognized in those days, and surprisingly, there are no significant additions to this list, but only refinements. In the absence of any Occupational Exposure Limit (OEL) for Diesel Particulate Matter (DPM) in SA, the Mine Safety and Health Administration (USA) rule is currently being used as a benchmark for the ventilation engineering designs. This paper discusses the ongoing SA journey of measurement and limitations of exposure data for ventilation planning and regulatory purposes. The currently accepted DPM limits are based upon the belief that they are economically and technically feasible for the mines to reach and are not necessarily health based. For SA underground platinum mines, a median TC/EC ratio of 1.8 with a range of 1.2 to 5.8 was observed. For SA coal mines, a median TC/EC ratio of 1.44 with a range of 1.25 to 2.13 was observed. While it is common practice in the USA to use the ratio of TC/EC for metal mines to be 1.3, the ratio found in local platinum mines is 2.2 and for coal mines, the ratio was 1.53 which is lower than Australian studies, i.e., 1.96. It has been shown that a need for critical analysis of TC/EC ratios exists, and possible reasons for variance must be understood before stringent adoption of overseas recommended limits for DPM. It is hoped that the findings from this paper would provide input to scientific approaches in developing appropriate conversion factors, limits for DPM and also in ensuring appropriate error factors (currently 1.14 for TC and 1.2 for EC) for compliance determination.

Jan 1, 2009

Two miners were fatally injured when a pillar bump occurred during retreat mining in a southern West Virginia coal mine. The mine was operating in the Eagle seam with overmining in the No. 2 Gas and Powellton seams. A coal bump is defined as a sudden and violent failure of coal caused by the release of stored strain energy in the pillar. While significant strides have been made by academia, industry, and regulatory agencies to better understand bump conditions and mitigation techniques, coal bumps represent a long standing, highly site-specific engineering problem in which the exact failure mechanism(s) is not clearly understood.

Jan 7, 2020

By John E. Caffrey

Mr. William. J. Montgomery in his book "Theory and Practice on Mine Ventilation stated "Ventilation is vitally important to underground mining for three reasons: First, it sweeps all workings with a plentiful supply of air and drives to the outside the smoke, gases, and contaminated air which would be injurious to the miners; second, it dilutes and renders harmless the explosive gases emitted from the strata, thus eliminating the dangerous conditions caused by the accumulation of these gases; third, it keeps the mine air as nearly as possible of the same composition as the outside air, thus giving to the miner the healthiest possible condition in which to work...." Specific methods to achieve the above basic reasons for mine ventilation were established in the Federal Coal Mine Health and Safety Act of 1969. Sections 303(y)(1); (y)(2), and Section 317(f)(4) of the Act, which can be broadly described as entrapment features, are controversial and debatable in the minds of many mining engineers in their intent and method for affecting, 303(y)(1) in certain cases prohibits the use of belt haulage entries as an intake for face ventilation, This is to say that air traveling in a belt entry will be placed into the returns and not used for face ventilation, 303(y)(2) limits the velocity of the air on trolley haulage entries. The regulations, as published in the Federal Register, have set this limit at 250 feet per minute unless a higher velocity is approved by the District Manager.

Jan 1, 1972

By G. E. Mellor, R. E. Lippoth, T. B. Faddies

The Little Rocky Mountains host epithermal- gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining these oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1) mineralization; 2) oxidation; 3) structural setting; 4) lithology; 5) alteration; and ultimately, 6) the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1992

By R. M. Carland, F. F. Aplan

Six natural zeolites were evaluated for their ability to selectively remove heavy metal cations from solution. Ion selectivity was found to be Pb+2>Zn+2>Ni+2 and Cu+2>Co+2 from their respective solutions. The presence of K+, Ca+2 and Mg+2 in the actual waters to be used may seriously interfere with the ion exchange and elution of cations from zeolites. Zeolites were found not to be effective in removing precious metals from their cyanide solutions.

Jan 1, 1995

By Robert Walker

The win theme of this session is Unique Material Handing Systems. The theme was selected because of two major factors. 1. Accomplishments of unique character manage to attract interest regardless of their age. 2. There is much to be learned from pioneering efforts of the past as they are the stepping stones to technological development. Thus, 2-1/2 years after completion, the engineering feat of Oroville Dam still looms large let us take a close look at this project to see what made it unique. To begin with, it established a number of firsts: At 770 feet it was the highest earth fill dam in the world. At $121 million dollars, it was the largest ever United States construction project (Civil). At 80 million cubic yards it had the largest earth volume of any dam in the world. The extensive use of belt conveyors for this application had never before been tried. The use of a high capacity bucket wheel-excavator with shiftable belt conveyors had never before been utilized as a con¬tractor's tool. The principal of the "integral train" was applied most effectively whereby up to 220,000 tons of material-was transported daily some 14 miles. To achieve optimum economics a number of technical breakthroughs were necessary. The suppliers of major commercial components worked hand-in-hand with system engineers to develop new machinery necessary for the highly mobile characteristics of the systems, viz., single pulley drives delivering 2000 horsepower, 1000 horsepower right-angle shaft-mounted reducers, across the line starting of 1000 horsepower squirrel cage motors, 10 miles of steel chord conveyor belts with belt tensions up to 150,000 pounds, aircraft-type disc brakes, hydraulic take-ups, train loading at a rate of 25,000 tons per hour, automatic train indexing for rotary dumping at 10,000 tons per hour, roll-over car dumping without uncoupling cars, shifting 7500 ft. long conveyors up to 300 feet laterally without disassembly. These are some of the superlatives that have made the Oroville Dam project unique. The measure of its success is demonstrated by the results.

Jan 1, 1970

By J. P. Matoney

The operation of a modern coal preparation plant, particularly in western Canada, is a very complex task. Most western Canadian operations are processing two or more, sometimes up to ten, different seams through the same plant. This requires a sophisticated multi-circuit plant that needs close operational control. Add the soft nature and large amounts of natural fines of western Canadian coal and you have a formidable cleaning task. To assist in the operation, programmable controllers and sophisticated control concepts are being more widely used. Two of the newest coal preparation plants in Canada have been designed by Raymond Kaiser Engineers Inc. and its Canadian subsidiary, Phillips Barratt Kaiser Engineering, Ltd. The use of programmable controllers and control systems will be illustrated by showing their application in a "typical" western Canadian coal plant. This example will cover flowsheet design, control concept systems application, and possible future uses.

Jan 1, 1983

By G. Deschênes

In Part I of the work, gold and silver were shown to be efficiently extracted from Kupol samples using lead nitrate in a cyanide leach system. In Part II, a comparison of the technical and economic merits of a new technology called CELP (CANMET Enhanced Leaching Process) was made with the cyanidation/AVR(Acidification-Volatilization-Recycling) process using 8 metallurgical variability samples as well as a large composite sample which represented initial two years of Kupol mill feed. The composite sample had 33.4 g/t Au and 289 g/t Ag. The metallurgical demonstrated that the CELP produced very similar gold and silver leach extractions compared to the standard Cyanidation /AVR leach conditions at 1/2 the cyanide concentration (1000 ppm NaCN in CELP vs. 2000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton, were approximately the same for the two technologies (total cost of the CELP with the use of Merrill-Crowe at $46.48/ton, with cyanidation/AVR at $46.13/ton). However, the implementation of the CELP would eliminate a capital expenditure of approximately $5 million. Eight variability samples used to confirm the previous results showed that on average the gold and silver leach extractions with the CELP and the feasibility leach conditions were very similar for gold extractions, but 4.6% higher for silver extractions compared to the conventional cyanidation. The decision was made to remove AVR cyanide recovery from the Kupol flowsheet and implement the CELP at Kupol. The ability to use conventional leach equipment with the CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2009

By P. R. Desam, J. D. Miller, A. Datta

The flow behavior of bubble-particle aggregates in separation tanks is important for many flotation systems, particularly for wastewater treatment. These aggregates can be considered as the dispersed phase in a continuous liquid phase of water and the flow characteristics determine the efficiency of the bubble separation process. In this work, a general methodology for the computational fluid dynamics (CFD) simulation of a bubble separation tank is described. This system is analyzed by Eulerian-Lagrangian approach. The momentum transfer from the dispersed phase to the continuous phase is quantified using the Particle-Source-In Cell (PSI-Cell) method. With CFD simulations, the effectiveness of different tank design parameters are evaluated in terms of the extent of bubble separation.

Jan 1, 2000

By K. S. Liddell

Ultra fine grinding is becoming increasingly used in the mining industry over recent years. The development of large-scale units for high volume grinding of low value materials and concentrates has opened up new areas of economical metal extraction. The ability of stirred vertical mills to produce very fine particles with high surface areas, is providing mine operators with novel extraction possibilities within gold concentrate regrind for Biox or leach feed, Activox autoclave feed preparation and lime slaking operations. The paper will review design, operational and maintenance aspects of ANI-Metprotech stirred vertical mills, comparing these to tower mills, horizontal bead mills and attrition mills.

Jan 1, 2001

By D. H. Carlson, J. H. Johnson, C. F. Renders

Introduction Diesel-powered vehicles are used extensively in underground mines throughout North America. The bulk of the diesel vehicles found in underground mining operations are used for loading and ore haulage, as well as for transportation of personnel and supplies. Along with the advantages of using diesels underground is the disadvantage associated with diesel-tailpipe particulate-matter emissions (DPM). The concentration of DPM in the ambient air of US underground metal mines is not now regulated by the Federal Mine Safety and Health Administration (MSHA). However, recent studies have shown DPM to be mutagenic (National Institute of Occupational Safety and Health, 1988), and the American Conference of Governmental Industrial Hygienists (ACGIH) has recommended that the exposures of per¬sonnel to DPM be limited to an 8-hr time-weighted average concentration (threshold limit value or TLV) of 0.15 mg/m3 (Anon., 1995). The authors, while making measurements in a number of US underground mines that use diesel haulage equipment, found mine air DPM concentrations ranging from 0.2 to 2.36 Mg/M3 (McCawley and Cocalis, 1986; Watts et al., 1989; Cantrell et al., 1991; Haney, 1992; US Bureau of Mines, 1992; Watts, 1992; Watts et al., 1995). If the proposed DPM TLV were to be adopted as a permissible exposure limit (PEL) for US underground mines, the proposed limit of 0.15 mg/m3 PEL would be lower than any of the concentrations measured in the earlier studies and would represent more than a 15-fold reduction from the maximum 2.36 mg/m3 concentration. A 0.15 mg/m3 PEL would also represent a 4.5-fold reduction from the average 0.68 mg/m3 measured mine ambient air DPM concentration reported in this paper. Other diesel tailpipe emissions that are now regulated underground include carbon monoxide (CO), with a PEL of 50 ppm; nitrogen dioxide (NO,), with a PEL of 5 ppm; nitric oxide (NO), with a PEL of 25 ppm; and sulfur dioxide (SO,) with a PEL of 5 ppm. Because the concentrations of these gaseous pollutants and DPM are affected by the state-of-maintenance (Waytulonis,1992), it is important that a means be developed to measure emissions from engines that are now in service to determine when maintenance is needed. The current study was the result of an inquiry by mine¬maintenance personnel who had been receiving complaints about high concentrations of diesel soot (DPM) in mine headings from load-haul-dump (LHD) vehicle operators. Mine-maintenance personnel were searching for an objective test to determine if the diesel tailpipe particulate emitted was excessive. The mine was also evaluating electronically controlled, two-cycle, naturally aspirated, direct-injection diesel engines on some of their JCI (John-Clark Inc.) load-haul-dump (LHD) vehicles. These LHD vehicles were used to haul freshly blasted ore from mine headings to a feeder breaker. The feeder breaker breaks down the larger chunks and feeds the broken ore onto a conveyor. Michigan Technological University, in past studies, developed an emissions-measurement apparatus (EMA) ca¬pable of measuring diesel vehicle tailpipe pollutant concentrations (Chan et al., 1992; Chan et al., 1993; Carlson et al., 1994). At the time of the study reported here, most of the mine's LHD vehicles used a 12-cylinder, four-cycle, naturally aspirated prechamber diesel engine. The study was undertaken in cooperation with mine maintenance supervisors from late 1992 through July 1993. The objectives were to compare diesel exhaust emissions between the 6-cylinder, two-cycle, electronically controlled, direct-injected diesel engine and the 12-cylinder, four-cycle, prechamber diesel engine and to, then, use the data collected, in conjunction with mine ambient air measurements, to demonstrate the application of the "deterioration factor" (Chan et al., 1992), which is a measure of the state-of-maintenance of mine-vehicle engines that are now in service. The information would be used to identify vehicles that need maintenance to reduce emissions. The data reported here are unique in the sense that they combine underground diesel vehicle ambient and tailpipe

Jan 1, 1999

The dissolution behavior of gold and copper from their elemental states and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc electrode. The anodic and cathodic reactions were studied separately and the resulting polarization curves were combined to examine the overall dissolution reactions. The dissolution rate of pure gold in the aerated cyanide solutions was inhibited by the anodic passivation on the gold surface, while the dissolution rate of pure copper was found to be mass-transfer-controlled. On the other hand, the dissolution of gold and copper from the alloys was partially controlled by electrochemical reaction and largely by mass transfer.

Jan 1, 1994

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020

By Larry F. Barrett

Anaconda exploration in the Rico mining, district from 1978 through early 1983 resulted in discovery and partial definition of the Silver Creek molybdenum deposit. Approximately 44 million tons of 0.31% Mo are drill-indicated, and projections suggest that the deposit exceeds 200 million tons. No source intrusion has been intersected by drilling, but its composition is suggested by silicic alkali-alaskite porphyry dikes of intramineral age observed at the surface and in drill holes. Age data and fluid inclusion studies indicate that the deposit was formed 5.2 ±2 m.y. ago and that more than 1,200 meters of cover has since been removed by erosion. Both emplacement of the hypothesized source intrusion, and the geometry of the molybdenum deposit, were influenced by three major intersecting faults. The most significant of these, the Last Chance fault, juxtaposes Precambrian quartzite and greenstone against Pennsylvanian clastic and calcareous sediments within the mineralized zone. Wallrock alteration associated with the deposit is characterized by potassic, phyllic, and propylitic zones in non-calcareous rocks, and garnet and anhydrite-diopside zones in the carbonates. All +0.2% Mo mineralization is within the potassic and garnet zones. Pre-mineral faults that intersect the deposit contain the only surficial molybdenum, tungsten, and fluorine anomalies. Pervasive dispersion haloes of the indicator elements were intersected at depth by drilling in the discovery phase of exploration, and are particularly well-developed in the hanging wall of the Last Chance fault.

Jan 1, 1985

By R. M. Schuster

This study attempts to compare the costs of transporting coarse coal by pipeline, versus the more conventional use of belt conveyors. Hydraulic conveying of crushed (not pulverized) coal has not had widespread commercial acceptance. However, there is little doubt that the technology is available, so that, should this method be proven economical for a given application, implementation of this technology will become more acceptable. Hydraulic transport by pipeline between the mine stockpile and the coal preparation plant, for distances normally considered practical for an overland belt conveyor, should be an ideal application. In this application there is no need for dewatering facilities at the receiving end of the pipeline, because, the receiving screens at the plant serve this purpose. Further, clarified water from the preparation plant can be recirculated back to the mine, a plus for water resource and environmental considerations.

Jan 1, 1982

By C. H. Cox

The Alumet Company of Golden, Colorado, is currently engaged in the development of their Diamond Creek and Lanes Creek phosphate ore bodies located near Soda Springs, Idaho. The Alumet Company is a partnership of National Steel, Southwire Co., and Earth Science Inc. Davy Powergas, Inc., of Florida was contracted by Alumet to perform an evaluation study of these properties and, in general, determine the tonnage of altered and unaltered phosphate reserves which would be amenable to beneficiation and production of merchantable phosphate rock (defined as material with a P2O5 content of 3 1.0% and greater). The Colorado School of Mines Research Institute was retained by Davy Powergas to develop a beneficiation method for the studies of the altered and unaltered ores. Ore reserves were classified by Davy in a comprehensive range of categories such that any partial grouping could be made as dictated by future mine planning, mine or mill design, or prevalent economic conditions. Categories included ore horizon, stripping ratio, degree of certainty of their existence, and physical and chemical characteristics. The last category was of interest for beneficiation considerations in that it dealt with the degree of alteration of the phosphate ore.

Jan 1, 1979

By C. Athanassopoulos

Geomembranes have been used in the mining industry since the early 1970s in solution and evaporation ponds, tailings impoundments, and heap leach pads. Traditionally, heap leach pad lining systems have consisted of a single geomembrane liner placed directly over a prepared subgrade of locally available soil. Heap fills are constructed by placing a layer of highly-permeable drainage stone (overliner) over the geomembrane. Crushed ore is then placed on the leach pad in 3- to 10-m (15- to 30-foot) thick lifts, sometimes reaching final heights of several hundred feet. The crushed ore is irrigated with a chemical solution which dissolves the precious metals from the ore. The nature of the chemical leaching solution depends on the metal being targeted. Low pH sulfuric acid solutions are generally used to leach copper and nickel; high pH cyanide solutions are used to leach gold and silver. The metal-laden pregnant leach solution (PLS) passes down through the ore pile and is captured in a drainage system. Metals are extracted from the leach solution and the solution is then recycled back onto the leach pile. When under load, geomembranes are vulnerable to damage from large stones both in the soil subgrade and in the overlying drainage layer. Although intact geomembranes are virtually impermeable, installed geomembranes will have a small number of holes due to imperfect seams or damage during construction and filling operations. These holes serve as open pathways for leakage into the soil below. Smith and Welkner (1995) estimated liner leakage rates ranging from 5 to 10,000 L/ha/day, depending on the type of heap pad liner and level of construction quality assurance (CQA). Thiel and Smith (2003) reported liner leakage rates up to 2,000 L/ha/day for a valley fill facility with heads ranging from 15 to 35 m.

Jan 1, 2011

By D. R. Hembree

This paper discusses the mineralogy and metallurgy of the Kuroko-style volcanogenic massive sulfide ores mined at Formosa Exploration Inc. I s Silver Butte Mine located in southwest Oregon. The principle ore type is pyrite + chalcopyrite + sphalerite, while subsidiary pyrite + bornite + sphalerite ore is also mined. The two styles of mineralization have distinctly different metallurgical behaviors and must be treated separately. Selective flotation methods are used to produce copper and zinc concentrates from the first ore type, while bulk concentrates are produced from the bornite ore. Careful mine planning and coordination between the mine and mill are utilized to achieve optimal recoveries.

Jan 1, 1993

By M. Jack Snyder

The problem of effective utilization of fly ash has been given wide attention for a number of years. Although the effort devoted to the problem has led to some applications of demonstrated usefulness, the full utilization of fly ash has been held back by lack of concerted research and development activity, by lack of effective dissemination to potential users of fly ash of the knowledge that is available from laboratory and field studies, and by the obvious variability of the product. Because of the variability in fly ash from one power plant to another and from time-to-time in the same plant, specifications have been set up defining compositional or property limits within which a fly ash must fall to be used in certain applications. This paper discusses the bases for such specifications and examines them in the light of recent research on the characterization of fly ash. Other limitations and restrictions on the use of fly ash and what is being done to overcome them are also discussed.

Jan 1, 1968

By L. R. Todd

Gold Fields' Mesquite mine, located in southeastern California, heap leaches low grade gold ore at an annual rate of 2.7 Mt (3 million st). Ore is crushed in a two stage open circuit and belt agglomerated prior to loading on the leach pads. Since initial heap construction in October of 1985, a number of operating practices have been modified and several agglomeration techniques have been tested in an effort to improve percolation and reduce leaching time. Findings to date are discussed.

Jan 1, 1987