Search Documents

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Gas holdup profiles in the collection zones of a pilot flotation column (0.91 m x 13.5 m) and a laboratory flotation column (0.057 m x 9.5 m) operated with air and water only were determined from pressure measurements. The profiles were determined discretely and continuously. For the pilot column, a minimum distance between pressure measurements was necessary to give reliable results. For the laboratory column, a third-degree polynomial fit to the pressure vs. height data was required. Water manometers proved to be less sensitive to sensor and process noise than pressure transducers. The profiles showed that gas holdup approximately doubled over a height of 8 to 10 m. The profiles were not linear, and the gradient increased towards the top of the column, especially for gas rates greater than 1 cm/s. The profiles cannot be predicted by a simple bubble expansion model. The implications of this new finding of a significant gas holdup increase with height in the collection zone on various aspects of flotation column design and operation are discussed.

Jan 1, 1996

By Stephen Semeniuk

Discussion by Stephen Semeniuk Discussion As a valuator and SME member, I view Ross D. Lawrence's position as based on unproven and faulty assumptions made with regard to the pragmatic evidence presented in his paper. Moreover, his call for the inclusion of all mineral resources in discounted cash flow valuations is redundant, if not irrelevant, as there are procedures that already take all classes of mineralization into consideration for valuation purposes. In my experience as a valuator, I find that Canadian securities regulators are more than accommodating in allowing any valuations of mineral properties to be based on cash flow calculations. In other business areas, the same regulators usually reject discounted cash flow valuations of projects or businesses with no operating history. Instead, the regulators prefer valuations to be based on other transactions tested in the marketplace. Valuations based on actual market transactions are less subjective than discounted cash flow calculations and/or the capitalization of arbitrary, untested or undemonstrated earnings projections. In the mining and minerals sector, such projections may be made by persons not qualified to make such projections. In support of this statement, I direct readers to the article "Valuation of mineral properties which do not contain exploitable reserves" by Lionel C. Kilburn, which appeared in the August 1990 issue of the CIM Bulletin. To quote from the article: "Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand, and political-economic conditions, all of which vary with time. Five fields of expertise influence the value of a mineral property: •geological engineering, •commodity markets, •financial markets, •stock markets and •mineral property markets. The skills of geologists and engineers properly apply to the first field of expertise. Knowledge and consideration of the other four fields is important, but such advice is more properly sought from marketing experts, economists and stockbrokers." Securities regulators have created no hardship for valuators by excluding unsubstantiated resources in discounted cash flow valuations. In the field of engineering, best design practices apply. A margin of safety is built into the design criteria for any new equipment or structure that will exceed normally expected load levels and stresses, even though such considerations imply higher front end costs. In accounting, the comparable operating principle is conservatism. It explains why, for balancesheet presentation purposes, inventory is stated at cost or market, whichever is the lowest value. Similarly, when the engineering or geoscience-based valuator plays in the field of finance, the rules of accounting and applied economics apply. Regulators in their skepticism of income-based valuations are in tune with similar views already expressed in mining literature. To quote H. Van Tingley, in Mining Magazine, July 1996: "... the DCF method has inherent dangers when applied to undeveloped resources. Firstly, it presents an often-undeserved aura of accuracy. A DCF value is no more accurate than the least accurate of the assumptions incorporated into the calculation - and assumptions

Jan 1, 2003

By R. Klimpel

Recent work has shown that the measurement of flotation kinetics in the laboratory is useful in providing guidelines on how operating sulfide flotation plant performance can be improved. This work outlines the influence of various factors on flotation kinetics such as collector/frother type and concentration, particle size, and frother blending.

Jan 1, 1981

By C. M. Chang, H Gu, J. A. Barrera-Godínez, T. J. O’Keefe

The inability to economically separate Fe3+(aq) from a variety of liquid effluents is a major Concern for the primary metals industry. A unique solvent extraction process, galvanic stripping, has been developed to address this problem. The galvanic stripping of iron from D2EHPA using only a 5~10 g/L H2SO4 solution is achieved after Fe3+ is directly reduced to Fee, in the organic phase using zinc metal additions. To date, the primary focus of the laboratory research has been on optimizing the parameters that control iron removal. The results from these studies have now been, used to make a preliminary design for a continuous flow process that is envisioned for zinc industrial applications. Specific quantitative data are shown for the use of a Zn-Ph cellos° in the iron-reams al process. Some introductory results on electrochemical potential measurements and impurity distribution with solution cycling are also giiven.

Jan 1, 2000

By Syd S. Peng

The key design parameters of roof bolting using expansion - shell type support for underground coal mine roof support are bolt length, bolt spacing, installed load and anchorage capacity. Depending on the utilization of suspension effect or friction effect, the bolt length is dictated either by the distance between the roof surface and the first overlying strong strata encountered or the desired magnitude of reduction in bending stress at the roof surface, The current prevailing practices about the bolt spacing and installed load are that an initial torque of 125 - 170 ft-lbs is applied and the bolts are spaced at 4- or 5- ft. square grid pattern. This seems to be a rather broad generalization in view of the great geological variances which are expected in underground coal mines. A modest evaluation program to measure the effectiveness of current roof bolting practices is to monitor the load history of roof bolts during a complete mining cycle including the phases of room development and pillar robbing. The load history, when compared with the anchorage capacity of roof bolts determined by in-situ pull tests, will provide information for evaluating the installed load, the bolt spacing as well as the specifications for structural and anchorage characteristics of the bolt assemblies. This paper presents a case history of monitoring the complete load histories of roof bolts in an underground coal mine of Pittsburgh seam.

Jan 1, 1976

By B. K. Cantrell, D. H. Carlson, W. F. Watts, K. L. Rubow

The use of diesel equipment in underground coal mines is controversial because the National Institute for Occupational Safety and Health (NIOSH) regards "whole diesel exhaust" as "a potential occupational carcinogen." Threshold limit values (TLVs) are recommended for the gaseous pollutants CO, CO2, NO, N02, SO2 and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the USBM have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) that utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines that used diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality. Air quality data were collected in four underground coal mines. The mines used continuous miners and diesel haulage equipment. Daily samples were collected at the section intake, haulageway and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments. These included the PDEAS and the micro-orifice uniform deposit impactor (MOUDI) that sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2 and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters. Concentrations of CO, C02, NO, NO2 and SO2 were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3.

Jan 1, 1992

By G. D. Schena

A decision support system for the management of the mineral resources of a developing country has been derived. The system allows the evaluation of the impact of a mineral project in a developing country in the broad context of its economy. The analysis permits the assessment of the overall socio-economic consequences of mineral prospects and allows incorporation in the evaluation of issues that are broader in scope than the pure financial objectives. The system is built around the Leontief framework of economic analysis. The original input-output model, enhanced to incorporate country-specific behaviour is integrated with cost-benefit analysis and shadow pricing. The analysis leads to synthetic measures of profitability at market and shadow prices. These measures are useful to direct the mineral policy of a developing country through the exploitation of those mineral resources which are most likely to bring about economic growth and social advancement.

Jan 1, 1992

By Peniti Niskanen

Outokumpu metals & Resources (OMR) is a sub-group of Outokumpu Oy. OMR is a Mining and Metallurgy group of about 75 companies in 16 countries. The main activities are exploration, mine development and, mining and metallurgical processing of base metals.

Jan 1, 1996

By SONGHE WANG, YI XUE, PENG HOU, CAIHUI ZHU, XUANYE JIAO, Feng Gao

The abstract discusses the challenges of coalbed methane development in China due to low coal seam permeability. It highlights protective layer mining as a method to reduce in-situ stress and enhance permeability for improved gas drainage and disaster prevention. The study involves experimental and numerical simulations to analyze gas migration and permeability changes during stress release. It includes a stress-strain-seepage coupled test on coal, development of a mathematical model for coal seepage under mining unloading, and a numerical model based on the Wulan coal mine to explore in-situ stress release, permeability evolution, and gas drainage in an unloaded coal seam. The aim is to demonstrate the effectiveness of combining protective layer mining and gas drainage technology for gas outburst risk elimination.

Mar 14, 2022

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

By G. R. Burman

Gilsonite is a brittle, natural solid bituminous resin, classified as an asphaltite. It is found in near-vertical veins in the Uintah Basin of Eastern Utah. Discovered well over 100 years ago by Samuel Gilson, this unique material has, since its finding, enjoyed a variety of commercial and industrial applications. Early uses for the product included black automotive paint and beer vat linings. Among its many important uses today are additives for oil well drilling fluids and cements, additives for sand castings for the foundry industry, reinforcing agent for asphalt pavements, and dispersing agent for black inks. Gilsonite is mined and processed in Bonanza, Utah, by two companies, American Gilsonite Company (AGC), an operating division of Chevron Resources, and Ziegler Chemical, a privately held company headquartered in New York.

Jan 1, 1990

By J. O. Leppinen

FTIR measurements using a special ATR cell were carried out to investigate the adsorption of two thiol collectors, potassium ethyl xanthate (KEX) and sodium diethyl dithlophoshate (NaDTP), on an unoxidized lead sulfide surface. Both qualitative and quantitative determinations of the collectors were made at the coverages from two monolayers down to 2% of the monolayer. The experiments revealed that the thiol collector species coordinate to the lead atoms at the surface of lead sulfide but the surface products distinctly differ from the precipitated bulk lead compounds. There exists a linear relationship between the coverage and the signal intensity of the IR spectra within the coverage range studied.

Jan 1, 1987

By T. L. Heidrick

Late Cretaceous-early Tertiary Cordilleran porphyry Cu-Mo districts and their consanguineous Zn-Pb-Ag-Au-W vein and replacement deposits of the Rocky Mountain region comprise one of the largest, best studied, diverse, complex, puzzling, and richest compound metallogenic provinces on earth. A concise space-time definition of intermineral plate, regional and local structure-tectonic frameworks is crucial to deciphering their diachronous metallogeny and enhancing the explorationist's odds of future discovery.

Jan 1, 2013

By Kumar Vikram

Rich reserve of prime quality limestone in east khasi hills of India and abundant quantity of low-cost fuel (Natural Gas) in Bangladesh made Lafarge Surma cement limited a joint venture company of Lafarge France and Cementos Molins Spain to envisage an integrated cement plant at Chatak District-Sylhet) a bordering town of Bangladesh. Since April 2006 the single flight 17 km Long Belt Conveyor (LBC) built by M/S Larsen & Toubro Ltd. (L&T), ECC Division an engineering and construction company of India, is feeding limestone/shale to the Lafarge Surma cement plant. This engineering marvel was created on a turnkey basis with technology support of M/S Aumund France

Jan 1, 2008

By Z. Sartowski, M. J. Pearse

The authors present laboratory and plant results illustrating the benefits to be gained by using chemical additives, namely flocculants and surfactant dewatering aids, in the Bayer process. Advantages of synthetic flocculants over starch are illustrated in terms of more efficient solid/liquid separation in both the initial settling of blow-down slurries and in the CCD wash train. In addition, it is shown that the use of synthetic flocculants considerably reduce the levels of organic contaminants present in the process liquor. Secondly, very significant improvements in moisture removal were obtained by the application of dewatering aids to hydrate filtration/ washing operations.

Jan 1, 1984

By Felicia F. Peng

Flotation process is particle hydrophobic surface-based separation technique. To improve the essential flotation steps of collision and attachment, and reduce detachment probabilities between air bubbles and hydrophobic particles, a selectively designed cavitaion venture-tube can be used to generate very high numbers of pico-nano bubbles to flotation column. Fully embraced by those high numbers of tiny bubbles, hydrophobic particles are readily attracting those tiny bubbles to their surfaces. The results of column flotation of Pittsburgh No.8 seam coal are obtained in a 50 cm ID and 162cm height flotation column equipped with static-mixer and cavitation-venture tube, using kerosene as collector and MIBC as frother. Design of experiment procedure combined with statistical two-stepwise analysis method are applied and attempted to made the optimizing the grade and recovery. The effect of independent variables on response has been explained. Combustible material recovery of 85-90% at clean coal product of 10-11 % ash are obtained from feed of 29.6% ash, with reduced amount of frother and collector than that used in conventional column flotation. The column flotation process utilizing the pico-nanobubbles can also be extended to the lower limit and upper limit of particle size ranges for better recovery minus 75 µm and 300-600 µm, respectively.

Jan 1, 2013

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

This study investigated the performance of citric acid as lixiviant for cathode material from end-of-life lithium-ion batteries (LIBs). Black mass containing 84.2 weight percent MNC (LiNi0.45Mn0.4Co0.15O2) and 15.8 weight percent LCO (LiCoO2) material was leached at solid-to-liquid ratios of 20, 50 and 100 g/L. Leaching with 1.5 M citric acid, 2 volume percent H2O2 and a solid-to-liquid ratio of 20 g/L at 95 °C extracted 90 percent Co, 95 percent Li, 94 percent Mn and 94 percent Ni within 20 min. At the highest solid-to-liquid ratio of 100 g/L with 1.5 M citric acid, 10 volume percent H2O2 and 95 °C, 84 percent Al, 84 percent Co, 87 percent Li, 86 percent Mn and 96 percent Ni were leached after 40 min, producing a leach solution containing 0.68 g/L Al, 20.0 g/L Co, 6.0 g/L Li, 13.6 g/L Mn and 19.3 g/L Ni. Using stepwise addition of H2O2, instead of initial bulk addition, did not significantly improve the leaching efficiency but did reduce the required leaching time. Temperature control of the reactor was also more manageable with stepwise addition of H2O2, and evolution of gas was less vigorous. It was observed that the leaching efficiencies of Co, Li and Mn decreased slightly at solid-to-liquid ratios of 50 and 100 g/L, while the leaching of Ni increased slightly. The solution leached at 20 g/L could be stored for six weeks without any spontaneous precipitation. However, solutions leached at 50 and 100 g/L showed changes in concentration after one month of storage, suggesting that processes that have a large material throughput and use high solid-to-liquid ratios around 100 g/L must ensure that the solutions are not stored for extended periods of time.

Apr 1, 2025

By W. Dresler

Since 1900, smelters have produced in Canada over 10 million tonnes of iron silicate waste slag containing significant quantities of nickel, cobalt and copper. The slag is reduced with aluminum and calcium oxide additions to produce a copper, nickel, and cobalt enriched alloy and an obsidian slag. It was found that the obsidian slag contained very low copper, nickel, and cobalt contents, indeed below 0.06% of each the base metals. These metals have been collected in a type of ferroalloy with up to 1.6% Cu, 2.1% Ni, and 0.7% Co. These alloys can be recycled according to standard procedures in base metal smelters. Surprisingly, the obsidian slag was found to display good cementitious and pozzolanic properties, which is a requirement for cement production. The strength producing properties of the obsidian slag are considered to be exceptional at the 28 day standard test age. In most cases, the obsidian concrete is characterized by significantly greater strengths than control concrete tests and concrete containing fly ash or blast furnace slag. Compressive strength data at 365 days for the obsidian concrete is impressive.

Jan 1, 2003