Search Documents

By Mark J. Logsdon, Barbara Basse

Mississippi Valley Type Pb-Zn deposits are widespread in the midcontinent U.S. and have been mined from the 1800's to present. Some tens of thousands of acres of mined land in the Tri-State District have been designated as Superfund sites as a result of surficial mine wastes and ground waters with elevated levels of metals. EPA considers the surficial mine wastes to be hazardous and a major source of acid mine drainage fAMD) that degrades water resources and threatens human health and the environment. To mitigate potential risks at one site near Galena, Kansas, a group of mining companies who had been identified by EPA as Potentially Responsible Parties IPRPs) proposed subgrade disposal of the mining wastes in shafts and subsidence features. However, this proposal was challenged by the Agency on grounds related to AMD and the potential for degradation of ground water quality. The PRP team developed a program of materials characterization, laboratory-scale leaching, and finally large-scale, pilot testing in the field. Static and dynamic leaching tests at both laboratory scale fusing artificial rainwater under both variably and fully saturated conditions) and field scale (using pH 4.5 ground water) showed that the surficial wastes do not produce acidic leachate and are not a long-term source of metals. Laboratory chemical and mineralogical tests show that the mine wastes contain substantial carbonate, but very limited iron sulfides, consistent with the leach test results. EPA "characterization" tests fEP Toxicity and TCLP) compare very poorly with tests simulating the expected leaching conditions. While these tests would classify the surficia1 wastes as "hazardous, they do not characterize the behavior of the high-volume, low-concentration, coarse-grained materials with respect to environments and disposal options of interest. To be meaningful, characterization of mining wastes must be performed in a manner that simulates the environmental conditions that are actually of interest with respect to a specific decision, such as subgrade disposal in the saturated zone.

Jan 1, 1991

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By J. C. Yingling, R. J. Sweigard, S. T. Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty inherent in the factor-of-safety (FS) predictions for soil slopes in which there is an incomplete knowledge of the spatial distribution of soil properties. A case study that considers a natural clay slope in Canada is presented. The sequential-indicator simulation technique was used as a means of generating a series of spatial maps of the soil properties at the site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. FS determinations were made for each simulated map using the simplified-Janbu approach. In using this approach, computations are performed using a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the FS distribution conditional to the type, position and value of existing site-characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1996

By Walter G. Steblez

The countries of Eastern Europe are former members of the Council for Mutual Economic Assistance (CMEA). Geographically, they are located in Central Europe (Poland, Hungary, Czechoslovakia) and Southeastern Europe, largely in the Balkans (Yugoslavia*, Bulgaria, Romania and Albania*). It is important to remember that all of the countries of Eastern Europe had central planning imposed on them by the Soviet Union during the years following World War II. "Stalinist" policy for industrial development had three important tenets: • central economic planning, or a nonmarket-based command economy with administratively set prices; • economic priorities that stressed the development of heavy industries such as mining, metallurgy (steel) and heavy machine building; and • self-sufficiency at all costs, which was aimed at abolishing reliance on the world capitalist market, or reducing it to a minimum. Essentially, the system of industrialization that was used in the Soviet Union in the 1930s and 1940s was imposed on Eastern Europe. Organic market economic development in Eastern Europe ceased during this period. The flaws of this experiment became apparent when mineral processing facilities were set up in many areas of Eastern Europe that did not have reliable resources. Poland, Hungary and Romania are good examples of this situation. The Soviet Union became the principal supplier of iron ore and other minerals and mineral fuels, not only to these countries but to the Bloc as a whole.

Jan 1, 1992

By Jamai Rostami

Mining, perhaps more than other industries, has been under pressure to achieve higher productivity, while reducing costs and environmental impacts. This has encouraged a move toward large-scale operations and greater integration and automation of systems. Mechanization is being used increasingly to raise production and reduce labor requirements. Yet, while transportation, ventilation and other activities have benefited from this trend, mechanization of rock excavation (for development and production) has lagged. The switch to a mechanized excavation system can be complex, requiring a thorough study of operational and cost benefits to be successful. To justify the high capital cost of mechanical mining equipment, production rates and the true costs of machine mining must be accurately estimated. To evaluate the cost effectiveness of mechanical mining for a particular operation, the total production cost (capital and operating) must first be estimated. This requires a reliable estimate of the production rate of the candidate mechanical excavator. Previously, the variable nature of rock caused performance prediction of these machines to be more an art than a science. Additionally, some of these machines are highly sensitive to operator skill. They all depend on their backup systems. The effects of interaction with the overall mining operation can be difficult to forecast. And a new system must surmount psychological barriers before it can become truly operational.

Jan 1, 1994

By A. D. Davis

A ground-water flow model was developed to simulate the post-mining recharge rate at the Belle Ayr surface coal mine in the Powder River Basin near Gillette, Wyoming. State regulations of Wyoming require that reclaimed lands should provide a rate of recharge that approximates the pre-mining rate. Steady-state calibration and transient simulations showed that the post-mining recharge rate in backfill is at least five centimeters per year, exceeding the original infiltration rate of 0.4 centimeters per year to shallow, overburden aquifers. Major reasons for the increase include the flat topography of reclaimed areas and decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate less than five centimeters per year but somewhat greater than the pre-mining rate.

Jan 1, 1995

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonite to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath. 1986 and personal communication). These bentonite; typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X- ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated bentonite to the oilfield since specifications are

Jan 1, 1990

By Waclaw Trutwin

The idea of automatic or remote control of the mine ventilation process generally, and methane concentration particularly, attracts the attention of mining engineers more and more. The advantages of introducing mine ventilation control systems are breaking traditional reluctance. The change of attitude is not only because of the requirements of modern exploitation technology, but it is also due to the recent progress in development and successful introduction of reliable monitoring systems and actuators in the form of controlled ventilators and doors [1]; [2], [3], [4], [5], [6]. Many 'years of theoretical and experimental studies of the dynamics of mine ventilation processes created the needed base for a proper design of an automatic control system [7],[8],[9], [10]. From these studies must, however, be drawn a fundamental conclusion, which may be regarded as the motto of this paper: An automatic control system for mine ventilation ill-conditioned or improperly designed is capable of creating hazard situations in response to random disturbances, much more, severe in consequence than a traditional ventilation system without any automatic or remote control! This statement is easy to prove if the dynamic properties of the ventilation process are taken into consideration. The ventilation process, as a matter of fact, is described by non-linear equations, and it must be expected that the process has more than one state of equilibrium. In other words, in the ventilation process may exist not only one but also more than one steady-states of flow, of which some are stable and others unstable. In certain circumstances, there may be no steady-state at all, and the process will oscillate [8], [11] , [12] . The state of flow in a network tends towards a steady-state and the actual steady-state established will depend on the initial conditions or disturbances in flow (fire,. etc.), which steady-state from the total number that will be . We frequently observe jumps from one steady-state to another. Disturbances in flow conditions which may cause such transitions are events of random character, occurring very rarely. Concluding, it must be stressed that there has to be a control system adjusted to the ventilation process in order to avoid situations mentioned above. There is only one alternative available and suitable for examination or study of the dynamics of a given mine ventilation problem: either by continuous monitoring of the real process, or numerical simulation of the process using a mathematical model. The advantages of the second method are obvious. This method allows consideration of every possible case very quickly and cheaply in relation to the first method. The aim of the paper is to show again that the simulation of the mine ventilation process and particularly a methane concentration process, separately or combined together with a control system, are real possibilities. A simulation method requires precise specification of the problem under consideration. For example, if we intend to examine a methane-concentration control system, the following items have to be specified: - expected target function of the control system. - structure of the control system. - mathematical model of control system, including sensor system, data preparation system, controllers, decision routine, regulators, etc. - structure of mine ventilation network. - mathematical model of ventilation process, including air flow and methane concentration processes. - pattern of disturbances which may occur in the controlled process as well as initial conditions on a 'start-up' of the system. Using typical computer programs for numerical solution of equations in the mathematical model of the problem involved, we are able, within the adequacy of the model, to simulate every case specified by the disturbances and initial conditions. As a result of simulation, it is expected that the following parameters could be defined: - transient flow in the network. - transient state of methane concentration in working areas. - stability of flow and methane concent¬ration. - stability of the control system. - range of control. - efficiency of control, etc. It is obvious that simulation methods readily allow for modifications to existing systems such that desired results will be obtained. Also optimisation problems could be solved by use of the simulation methods. In order to illustrate these general thoughts, a brief presentation of a mathematical model of methane concentration and

Jan 1, 1980

By Nora M. Hutt, Kevin A. Morin

There is currently some pessimism over mixing of net-acid-neutralizing (NAN) and net-acid-generating (NAG) rock to obtain indefinite near-neutral seepage from mined-rock piles. This is due in large part to the lack of well- documented, successful cases of blending and layering, and to the knowledge of unsuccessful attempts. Past work often defined a potentially successful mix in terms of the ratio of net-acid-neutralizing rock to net-acid-generating rock. For example, one case study indicated the bulk pile-wide ratio was approximately 3: 1. Since this exceeded a common ratio used in acid-base accounting, no acidic drainage was predicted. However, acidic drainage appeared within two years. A large part of the ambiguity in mixing arises from attempts to predict success based on a ratio. This paper looks in detail at simple discrete-zone mixing, where at least one truckload of NAG rock is placed in a particular location with no further rehandling or dozing. The lack of acidic drainage in this scenario is dependent on the intervening distance between the discrete NAG zones, along flowpaths occupied by NAN rock. Calculations show that the bulk mixing ratio of a mined-rock pile is not an accurate indication of whether near-neutral drainage can be maintained. For example, a pile with a bulk ratio around 300: 1 could still release some acidic drainage. Calculations also show that the minimum separation distance of the NAG zones (L) can be so great, even with typical NAG and NAN rock, that the mixed pile could safely contain only a few percent of NAG rock, which would not be sufficient for many minesites with NAG rock. The comparison to a more elaborate, computer-based statistical model shows that the simple discrete-zone approach will provide a reliable yes-no indication of whether any acidic drainage will leave a pile. However, predictions of whether combined downstream drainages will be acidic depend on numerous site-specific physical and geochemical factors within and below a pile that cannot be modelled in a general way, like the number of flowpaths and the nature of their intersections.

Jan 1, 2000

By John R. Keith

Keith, John R. 1968. Relationships of lead and zinc contents of trees and soils, Upper Mississippi Valley District. Preprint, Fall 1968 Meeting, Soc. Mining Engineers of AIME. Lead and zinc contents of elm, maple, and oak trees and of soils in which the trees grew were determined in samples from the Upper Mississippi Valley mining district, and from an area outside but contiguous to the district. The lead and zinc analyses of plant materials served to differentiate the mineralized and non-mineralized areas. Stems contained about two times as much lead and about 2-5 times as much zinc as did leaves taken from the same stems. Lead and zinc analyses of all soil horizons could be used to differentiate between the two areas. Soils at most sample sites in the mineralized district seemed to be more reliable than plants for geochemical prospecting and are a more practical sampling medium. Soil samples from areas with thick loess cover, however, failed to indicate the presence of mineralized bodies whereas tree samples from the same sites contained anomalous amounts of lead and zinc. It is suggested that in areas of thick loess cover plant samples could be used in prospecting for lead and zinc.

Jan 1, 1968

By K. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 meters (1MPa, tensile strength) in the rock mass, a distance that is sufficient to impact the pit-scale slope over the long term. In addition, the damage zone was calculated using the reasonable assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone ? up to 5.6 meters (30MPa, 30% of the compressive strength) ? indicates that microfracturing can occur throughout the entire rock mass in the blasting area. Finally, an economic analysis was conducted by comparing two reasonably assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond?s law after increasing the blast energy from 180kcal/t to 350kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. An optimal blast design should consider both slope stability (safety) and downstream comminution energy (production).

Feb 23, 2014

By Brent W. Madsen

To assist in fulfilling the Bureau of Mines goals of maintaining adequate mineral supplies to meet national economic and strategic needs, and to minimize the environmental impacts associated with mineral-processing operations, a leaching-solvent extraction-electrowinning technique was compared with a leaching-cementation technique for processing low-grade copper ores. Large-scale laboratory column leaching tests (6 to 7 tonnes) were conducted on minus 37-cm chalcocitic ore using ferric sulfate leach solutions at 25° C. Two columns contained 11 percent minus 1.27-cm fines, and two columns contained 32 percent minus 1.27-cm fines. After 416 days of leaching ore samples containing 11 percent minus 1.27-cm fines, copper extraction was 48 and 51 percent for the leach-cementation and leach-solvent extraction-electrowinning procedures, respectively. When leaching ore samples containing 32 percent minus 1.27-cm fines, the leaching-solvent extraction-electrowinning technique extracted 60 percent of the copper after 568 days, whereas the leaching-cementation technique extracted only 48 percent of the copper. In the latter test, leach solution ponded on the ore, which reflected a decrease in ore column permeability. The decreased permeability was attributed to the generation of excessive amounts of iron salts during cementation; the salts precipitated on the fine ore particles and in the interstices, thus plugging the column. This decrease also lowered the available oxygen, resulting in poor aerobic bacterial activity which slowed the oxidation rate of ferrous ions to ferric ions. Sulfuric acid required to maintain a leachant pH of 2 was nearly halved when copper was recovered by solvent extraction and electrowinning rather than by cementation.

Jan 1, 1979

By F. W. Brackebusch

In the paper presented by F.W. Brackebusch on the "Basics of paste backfill systems," paste fill was presented as a backfill process that offers many advantages over other alternatives such as hydraulic fill and rock fill. It was observed, however, that the mechanics of paste-fill transportation in pipelines is not fully understood and that the success of its implementation in practice depends on the precise control of the proportions of fines, aggregates and water in the mixture. The author emphasized the necessity for laboratory and full-scale testing to determine the suitability of a material to be used as paste fill. Although experimental testing is definitely an important operation in the design of a reliable paste fill, advances in the understanding of the fundamental laws that govern paste flow in pipelines are equally relevant. Ideally, the results of such efforts would provide predictive models for the rheology of the paste and the corresponding pumping-energy requirements. In an attempt to achieve this objective, an ongoing research program has been active at McGill University's Department of Mining and Metallurgical Engineering. Preliminary results showed that the underlying mechanics of paste-fill flow in pipelines may be described in terms of what is known as "plug flow," as depicted in Fig. 1. Although this flow mechanism has been known qualitatively for many years, few attempts managed to offer a comprehensive model (Gandhi, 1987; Duckworth, 1986). In our model, it is assumed that coarse aggregates present in the mixture form a porous core, which is filled with paste (fines and water) and is surrounded by an annular non-Newtonian (Bingham-plastic) lubrication layer, which enables the mixture to flow with pressure losses that are easily overcome by common positive-displacement pumps. In summary, our model predicts the thickness of the annular lubricating layer, which controls the magnitude of the pressure losses. This is done either by collecting data on the apparent viscosity of the Theologically-active fine fraction and using an analytical equation (Bouzaiene, 1994), or is done by measuring the void content of the coarse aggregates and deducing the thickness as a function of the fine- to coarse (weight or volume) fraction ratio in the mixture for a given pipe diameter and solids concentration. Our model predictions showed good agreement with data from Duckworth et al. (1986), as shown in Fig. 2.? References Bouzaiene, R., 1994, "Hydraulic transportation in mining," Ph.D. dissertation in progress, McGill University, Dept. of Mining and Metallurgical Engineering, Montreal, P0, Canada Duckworth, A., Addie, G.R., and Maffei, J.R.,1986, "Mine waste disposal by pipeline using a fine slurry carrier," Proceedings of the 11th International Conference on Slurry Transportation, Slurry Transport Association, Washington DC. Gandhi, R.L., 1987, "Effect of rheological properties of fines fraction on slurry hydraulics," Proceedings of the 12th International Conference on Slurry Technology, New Orleans, LA.

Jan 1, 1996

By C. D. Wittreich

The University of Idaho, Department of Metallurgical and Mining Engineering, through the Generic Mineral Technology Center, has been engaged in mine design research at the Lucky Friday Mine, Mullan, Idaho. The purpose of the research is to develop and implement the longwall underhand cut-and-fill mining method for conditions at the Mine. The longwall underhand cut-and-fill mining method involves backfilling mined stopes with a compacted tailings-cement mix. After the backfill has been allowed to cure, mining is resumed from underneath. Horizontal stresses in the Lucky Friday Mine are exceptionally high and rock bursts are a common problem. Beus and Chan (1980) have reported a 2:1 horizontal to vertical stress ratio at the mine with a 65-MPa (9,500-psi) maximum horizontal stress at the 1,295-m (4,250-ft) level. Using this mining method under these stress conditions, it is desirable to have a backfill material that has sufficient strength to safely carry the high horizontal wall loads while minimizing external steel supports.

Jan 1, 1987

By Kenneth A. Rogers, Richard F. Hill

Introduction A number of processes for deriving more convenient liquid and gaseous fuels from coal are commercially available or in final stages of development. Generally, synfuels from coal processes have efficiencies ranging from 50 to 70%. Considerable engineering design and development work are necessary to bring forth commercial plants using the various technologies-but technological breakthroughs are not expected or needed. Gasification While a variety of solids handling, gas contacting, and gas quality upgrading techniques may be employed in the various gasification processes, the primary goal is the same-to convert a sulfur-containing solid to an essentially sulfur-free gaseous product. The gaseous product may be a mixture of hydrogen and carbon monoxide with nitrogen. Definitions are not rigorous, but high-Btu gas is generally over 900 Btu/scf(33 534 kJ/m3) and low-Btu gas is generally below 350 Btu/scf(13 041 kJ/m3). Medium or intermediate gas falls between these values. High-Btu production is more difficult, as it requires additional upgrading of a low- or intermediate-Btu gas stream to produce a commercially acceptable product. The carbon/ hydrogen ratio is adjusted either by rejecting a portion of the carbon, increasing the hydrogen, or a combination of both. The chemical processing steps include production processing gas containing carbon oxides and hydrogen by the reaction of carbon and steam (gasification); reaction of hydrogen and coal to form methane (a hydrogasification process); reaction of hydrogen and carbon monoxide to produce methane (methanation); and the removal of impurities. The gasification processes share a number of common techniques. The coal received at the plant site must be further cleaned and crushed or ground before it can enter the gasifier. Conventional cleaning methods are used to remove extraneous materials such as metal, rocks, etc. For some processes the coal must be finely ground so it may be fluidized or entrained in a flowing gas stream. For other processes crushing and sizing only are required. Agglomerating coals may be pretreated by heating, mild oxidation with air, or other procedures to assure smooth gasifier operation and to avoid reactor plugging. Nonagglomerating coals Such as lignite and subbituminous coal normally do not require pretreatment. Feeding a solid material such as coal to a higher pressure reactor is a difficult task. Dry feeders using a series of pressurized lock hoppers, or wet systems in which a slurry is pumped into the reactor, are used. The gasification step is the heart of the process. Here, the solid feed material is contacted with synthesis gas (carbon monoxide and hydrogen). The coal is devolatilized and a portion of the fixed carbon converted to methane. The gas-solids contacting methods used include fixed beds, fluidized beds, moving beds, entrained beds, and free-fall systems. The gasification process, overall, is endothermic and the heat required to maintain reaction rates is usually supplied by burning a portion of the coal feed. External heat sources such as electric resistance heating, molten salt or solid heat carriers, and the introduction of a hot hydrogen stream also have been tested. Following the gasification step the particulate materials and heavy hydrocarbons contained in the reactor effluent are removed by a water quench and solids separation system. If low-Btu gas or synthesis gas is the desired product, the raw gas is scrubbed to remove carbon dioxide and sulfur compounds and then is used directly. However, if high-Btu gas is desired, methanation is necessary. In most gasification processes, the hydrogen content of the gasifier

Jan 2, 1980

By R. H. T. Garnett

Reserve estimation is a process that commences with sampling and culminates in the issuance of a reserve statement. The tin, gold and diamonds that occur as marine placers on the continental shelf are low grade with very erratic mineral distributions. Sampling, using a variety of special equipment, determines the extent and grade of the mineralization. The sample size is important, especially for diamonds. Together with the sampling density, it determines the accuracy of the grade estimate. Bulk sampling is a confirmatory process. The choice of mining equipment, either new or developed from onshore activities, dictates the unit costs, the cutoff grades and the selectivity of extraction. Thus, the size of the blocks that comprise the mining plan and the reserves are determined. A variety of estimation methods of different reliability are available, with the most sophisticated being kriging. Dilution and losses during mining must be taken into account in estimation, and a grade-volume curve should be constructed. Diamond deposit estimation also involves an extra variable, the dollar value of the stones. During and after mining, essential feedback on the accuracy of un estimation may be given by the RIE factor and by a mineral balance. Reserve estimates are required for several reasons and may be subject to public disclosure. The use of the correct definitions is, therefore, important.

Jan 1, 1999

By S. R. Stine

The Cyprus Thompson Creek Mine is located at 2,286m (7500 feet) elevation in the Central Idaho mountains, 61.16 kilometers (38 miles) southwest of Challis, Idaho off State Highway 75. The Thompson Creek molybdenum deposit lies near the eastern border of the late Cretaceous Idaho Batholith within a complexly deformed sequence of Paleozoic sedimentary rocks. Molybdenum mineralization is contained in a composite biotite granodiorite-quartz monzonite stock considered to be genetically related to the Idaho Batholith intrusive event. The ore is being mined by open pit methods and delivered to the concentrator stockpile with an overland conveyor belt system. The concentrator is designed as a 22,680 metric tons (25,000 ton) per day plant at an average head grade of 0.1% Molybdenum.

Jan 1, 1986

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By S. V. Tracy

The Outokumpu Skim-Air Flash Flotation machine was developed to separate valuable mineral from gangue as early as practical by floating it with specially designed flotation equipment installed in the grinding circuit. Machines already in service have shown the ability to produce final grade concentrate with an increase in overall recovery and flotation rate while decreasing filter cake moisture and reducing fluctuating feed grades to conventional flotation circuits. The first US production test was carried out in a southwestern copper concentrator with successful results. This report describes the results of the test along with an explanation of the process and the benefits obtainable.

Jan 1, 1986

By B. Hester

Many Third World countries of Third World Africa are well-endowed with minerals, especially gold. Political and economic conditions discouraged interest by Western capital for the several decades since colonial rule. Influence from Eastern Block countries has gone and the left wing orientation widely favored by Third World countries has almost disappeared. Under International Monetary Fund influence, these countries now solicit Western finance to expand their industries. Mining is especially encouraged. The paper describes the financing of some recent developments and examines trends and opportunities in some of the more attractive countries.

Jan 1, 1993