Search Documents

By Richard D. Nichols

A new method of slaking lime has been developed by DENVER EQUIPMENT DIVISION of Joy Industrial Equipment Company and patented under U. S. Patent 4,261,953. The new method utilizes an attrition machine, commonly used in mineral processing circuits as a sand scrubbing device, to slake lime. The scrubbing effect of the attrition slaker continuously produces a fresh reactive surface so that further slaking may occur. This process allows for utilization of slaking all grades of burnt lime and most grades of dolomite lime. Testing indicates that poor grades of water usually not considered for this service can now be tolerated using the attrition slaker. The slaked lime produced is of higher quality, faster reacting and much less apt to produce scaling problems than previously experienced. The attrition slaker can be combined with a spiral classifier and ball mill to eliminate any need for grit handling or grit removal. The attrition slaker can be designed for all burnt lime tonnages up to the limit of 175 tph and 1" pebble lime size. Control can be maintained easily with minimal operator assistance. The equipment, the principals of process metallurgy, and the above topics will be presented.

Jan 1, 1982

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Pertti Koivistoinen

There are many grinding schools in the mining world, which claim their grinding method to be the best possible - and still the methods concerned vary a great deal. Some of them have multi- stage crushing and only single stage grinding while in others crushing may be nominal, but grinding can be very complicated. - In this presentation firstly the nine most common comminution circuits will be analyzed. Then results from a pilot scale test series will be reviewed, in which nickel ore ground by four different comminution methods was fed to a common flotation treatment.

Jan 1, 1995

By R. M. Guymon, D. D. Lauriski

Safety management can best be described as how each company deals with the control of hazards (human or mechanical) to reduce costly accidents and employee injury caused by accidents. Properly used, effective safety management can mean the difference between being a highly productive, cost-efficient operation or one that "walks the fence," that is less productive with higher product costs. At Utah Power & Light Co's mining division, effective safety management has been used as tool to achieve this difference and remains as the number one priority to maintaining that difference.

Jan 1, 1990

By T. Hall, R. Ferris

Waterjets and diamond wire saws have raised the productivity and lowered the cost in dimensional granite quarries. While the cost of diamond wire sawing is substantially lower than waterjet, the judicial use of the waterjet can simplify and improve the overall operating efficiency and predictability. Granite is the hardest commercial stone and only the gem-stones garnet and diamonds are harder. The introduction of industrial diamonds has made it possible to quarry and process granite at costs equal to or less than other natural stones – making granite, with its superior properties, the best value available.

Jan 1, 2004

By Robert P. Larkin

The necessity for mineral extraction and its impact on man and the natural environment is a subject of increasing concern to Americans. Rising living standards and new demands for energy require increased mineral extraction, whereas the "new environmentalism" and concern over social well-being warn of the dangers to both the environment and the social system. This dilemma can only be solved by a complete understanding and analysis of all the factors relevant to human welfare which include environmental considerations, economic implications, and the social and psychological dimensions. A decision-making framework is therefore necessary which will encompass all relevant views of the problem.

Jan 1, 1975

By D. Wright, J. Samborski

DuPont’s Florida Plant has been mining in northeast Florida and supplying titanium-bearing minerals, zircon and staurolite for over 50years.The site has successfully implemented and “sustained” a land reclamation/habitat enhancement program that goes beyond regulatory requirements and standard industry practices. However, the term sustainability has been used by so many organizations, many with divergent viewpoints, that it is important for a mine to develop its over-all concept and approach to sustainable operation. As a foundation, the outstanding reclamation efforts at DuPont’s mine will be presented followed by a broader look at the overall sustainability strategies and tactics used at the site.

Jan 1, 2004

By Marion A. Goudie

The Devonian salt basin, which contains the Saskatchewan Potash deposits, extends from just east of the foothills in Alberta, north as far as the Peace River area, across Saskatchewan and into Manitoba as far east as Range 10 west of the First Meridian and south into Montana and North Dakota. The basin is closed everywhere except to the northwest. The known potash deposits are confined almost entirely to the Province of Saskatchewan, with the exception of a small area in western Manitoba bordering the Saskatchewan boundary. The following discussion will concern only the Saskatchewan part of the basin. The evaporite series in the basin is defined as the Prairie Evaporite Formation of the Elk Point Group, of Middle Devonian age. Recent work done by potassium-argon dating methods has indicated an Upper Middle Devonian (Givetian) age of from 265 to 347 million years for the potash. The Elk Point Group consists in ascending order of the Ashern, Winnipegosis and Prairie Evaporite Formations. The Ashern formation, sometimes called the Third Red Bed, consists of dolomitic shales or shaly dolomites. The Winnipegosis is a reef type dolomite, usually with good porosity, and in many cases oil-staining, although to date no production has been obtained. The Prairie Evaporite formation consists of anhydrite overlain by halite and finally, in Saskatchewan, by the potash beds. In almost all wells which have been cored for potash the lowest potash bed is underlain by one or two bands of anhydrtte, which are used as marker horizons. Cores from a few wells which cored to the bottom of the salt series have shown flecks of potash throughout the halite.

Jan 1, 1959

By Kenneth L. Clifford

We have heard a lot during the recession about the mining industry now competing in a world market for sales of such commodities as copper, lead, zinc, molybdenum, iron ore, and phosphate. If the US mining industry is to survive, do we not have to reduce direct operating costs to a minimum? How significant is labor cost compared to consumables, electricity, fuel, maintenance, materials, and transportation? Ore grade is ultimately the dominant factor; but can we offset its dominance by improving productivity? Is the US mining industry perhaps only 25-30% as productive as it might be? What prevents the industry from being more productive? Can we retrofit older plants to be more productive or does it take a new plant with the largest equipment available for each unit operation? Present Productivity A copper industry study a few years ago covering 13 US copper concentrators ranging from about 10-45 kt/d (11,000-50,000 stpd) showed that productivity did not vary with capacity above 18 kt/d (20,000 stpd). Operating productivity varied significantly, however, from about 180-635 t/d (200-700 stpd) per operating hourly worker in most units, but one operation had 900 kt/d (1,000 stpd). Concentrators with more than 545 t/d (600 stpd) per hourly worker were in the 23 kt/d (25,000 stpd) or more category. Maintenance productivity covered about the same range, but most concentrators were in the 270¬635 t/d (300-700 stpd) per hourly maintenance worker. Again, one company stood well above others by exceeding 1 kt/d (1,100 stpd). Total hourly productivity ranged from 125-280 t/d (140-310 stpd) per hourly worker for most concentrators. The company with the most productive operation, however, was above 455 t/d (500 stpd). Salaried worker productivity for most operations was in the 725 t/d to 1.2 kt/d (800-1,300 stpd) per salaried worker range. The best operation was 2.2 kt/d (2,400 stpd). The end result is, of course, tons per day per total personnel. Most operations fell in the 110-220 t/d (120-240 stpd) range with the best operation at 400 t/d (440 stpd). This is the productivity definition that is most directly related to unit costs. Many of these operations have made some productivity progress

Jan 11, 1983

By D. M. Steelman

Digital systems have been employed in industry as an aid in process evaluation and control for about 20 years. The earlier systems were quite simple and did little more than periodically scan a multitude of process variables, perhaps comparing them to alarm limits, and print out the results. As time passed, the needs of industry and the imagination of process engineers became more demanding. Rather than perform only alarm checking and logging, operating guides were generated to help the operator gain optimum performance from the process. Eventually, systems were entrusted with the job of manipulating the set points of the local analog control loops in a (DDAC) digitally directed analog control mode. Today digital systems are used to gather all-the process information, including both analog and digital variables; to make the necessary data manipulations; and to control the process end elements in a (DDC) direct digital control mode. During these years of transition from the very simplest systems to the complex systems of today, the demands upon the system engineer have been every increasing. The process engineer has required, among other things, more computational ability at high speeds, faster input and output rates, greater flexibility, better communication facilities (man-machine interface), (process oriented software), and finally, greater reliability at lower cost.

Jan 1, 1969

By W. James Marold

The New Croton Aqueduct (NCA) was the first major water supply tunnel for New York City. The 50-km (31-mi) long tunnel has 33 open shafts 6 m (20 ft) to 121 m (397 ft) deep. The tunnel and shafts are lined with brick and mortar, with cast iron lining and pressure covers in six pressurized shafts. Details of the 1895 construction are provided and compared to modern construction techniques. The paper provides rehabilitation techniques for the shafts and pressure covers, including grouting, epoxy lining, temporary bulkhead design and installation and placement of tremie concrete 98 m (320ft) below the water level in a 122 m (400ft)deep shaft using a Remote Operated Vehicle (ROV) to monitor the placement.

Jan 1, 2008

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By Kelly F. Bailey

The issue of regulating non-asbestiform varieties of the amphiboles actinolite, tremo1ite, and anthophyllite to the same degree as asbestos has been studied in detail by the National Stone Association. The ramifications of such a regulation, and the over simplistic regulatory definition of a fiber, are enormous not only for the aggregate industry and its users, but also for the nation. Evaluation of the health, geological, mineralogical, technical, economic and legal issues do not support an "asbestos-like" regulation of non-asbestiform minerals. The adverse consequences of regulating non-asbestiform varieties of actinolite, tremolite and anthophyllite like asbestos would be magnified many times if a similar standard for generic mineral fibers were promulgated.

Jan 1, 1988

By R. M. Enick

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. The separation, conducted at ambient temperature and a pressure of about 1000 psi a, was based on the difference in wettability of precious metals and minerals. Contact angle results indicated that in the presence of water and liquid CO2, gold, platinum and silver had intermediate wettability. Minerals such as quartz and magnetite, however, were hydrophilic. Therefore fine gold particles. -325 mesh, that were mixed with water and liquid CO2 dispersed in the CO2 or agglomerated at the H2O-CO2 interface while the minerals tended to remain in the aqueous phase. Best results were obtained when these fine gold particles were liberated, were not agglomerated in slimes, were not adhering to minerals, and were not coated with minerals.

Jan 1, 1998

By F. Calizaya

This study summarizes the ventilation requirements for a highly mechanized P.T.Freeport Indonesia's underground mine operation in Irian Jaya, Indonesia. The Deep Ore Zone (DOZ) is a copper-gold deposit being developed underneath the current Intermediate Ore Zone (IOZ) mine. One of company's current plans is to prepare this mine for a steady oreflow of 25,000 tpd by year 2003. This study includes the estimation of airflow requirements for various mining activities, the design of major intakes and returns, the determination of airway resistances and specifications of fan duties. It also includes the results of air pressure/quantity measurements in existing airways and the standards stated by the current Indonesian mining law.

Jan 1, 1998

By Prescott Greene

AVAILABLE MACHINES Machines discussed in this section include only rubber tire mounted kerf cutting machines of a self¬propelled electrically powered design. Such machines handle bars up to 4.6 m (15 ft) in length, cutting kerfs of from 115 to 191 mm (4.5 to 7.5 in.). The basic design concept of all machines currently in production is very similar. The chassis features dual driving wheels on the cutter-bar end, fixed directly to the main frame. The steering wheels on the outby end of the frame are articulated in some manner to keep all four wheels on the floor over uneven bottom. Machine power for tramming, and all other functions except powering the cutting chain, is furnished from a pump motor that drives the specific pump or pumps required by a given machine. The cutter chain is driven through a mechanical drive train from a separate electric motor having no duty other than driving the chain. The general arrangement of a cutting machine is shown in Fig. 1; two types of machines, with their specifications are shown in Figs. 2 through 5. A hydraulically powered cable normally is included to eliminate the need for manual cable handling and make this a one-man machine. A bug duster, though optional, is needed for most applications. The bug duster is an hydraulically driven scroll conveyor located directly behind the cutter chain drive sprocket. Its function is to move the cuttings away from the sprocket to prevent them from packing up in this area and consuming a lot of machine power to further pulverize them. Available machines vary from models 610 mm (24 in.) high that can cut horizontally only from 203 mm (8 in.) below ground line to 229 mm (9 in.) above, to machines 1143 mm (45 in.) high that can cut in any plane from 178 mm (7 in.) below the ground line to 3.7 m (12 ft) above it. Most currently manufactured machines fall in the 17 200 to 20 400 kg (38,000 to 45,000 lb) weight range, but can be dis¬assembled for underground installation where weight and size are a problem. Maximum teardown results in all pieces having a weight of 5400 kg (12,000 lb) or less and a size allowing passage through a 1.2 x 2.1-m (4x7-ft) opening. Further reduction in either size or weight of the parts becomes a serious problem. Machines currently being manufactured are avail¬able for use with power supplies of 250 v dc; 500 v dc; 440, 550, or 950 v ac (60 Hz). Also available are machines for use on 415, 500, and 950 v 50 Hz. De¬signs to allow operation on other voltages of either 50 or 60 Hz can be made available without any serious problems. As of September 1977, a typical medium-seam ma¬chine without the extra options needed for unusual conditions, but fully equipped to operate, was selling for about $185,000. CAPABILITIES Materials That Can Be Cut The problem of deciding before a machine is put on the job whether it can work effectively is an old one that has never been completely solved and probably

Jan 1, 1982

By P. Gelfi, G. Hill, A. Showell, V. Martins, R. Dunne, R. Jenkins

Carbon attrition losses are not usually a prime consideration for CIP equipment selection and CIP plant design. However, the costs as a result of carbon attrition and associated gold lost with carbon can be high. Recorded carbon losses for Newcrest operating gold plants were shown to vary widely from plant to plant. The Tuckabiana plant recorded an overall loss of only 0.3g carbon /t ore which is very low by industry standards. A comparative carbon management study was undertaken by Newcrest to highlight the reasons for the excellent record of Tuckabiana operation compared to other Newcrest plants. This paper discusses the results of the comparative study and high­lights areas of concern with respect to carbon attrition.

Jan 1, 1995

Continuous improvement has become the watchword of the 1990s for most iron-ore-processing operations. In many instances, this improvement has been achieved through stepwise application of advanced control techniques to optimize operations. The benefits of this stepwise application have been great. However, they have fallen short of the full potential offered by the prospect of overall plant optimization. The successful integration of computers, instrumentation and control software throughout a plant promises to deliver an additional 3% to 5% of productivity in even the best-run plants (Herbst and Bascur, 1984). LKAB is Europe's largest iron-ore producer and a leading implementer of advanced control technology. In the late 1980s, LKAB introduced advanced control in its concentrator at Kiruna, Sweden to improve plant performance through higher productivity, greater efficiency and lower costs at each processing step.

Jan 1, 1995

By Harold D. Taylor

Lognormal grade distributions are definitely the rule rather than the, exception in many types of deposits, including precious metals, uranium, and many others. The "normal theory" geostatistical techniques do not work well in these situations because the occasional high grade values, perhaps several orders of magnitude larger than the median, can overwhelm the rest of the data, resulting in variograms and Kriged estimates which are unrealistic or even ridiculous. Robust techniques for variogram modeling have been proposed, and truncation of high sample values can produce more reasonable Kriged estimates, but the technique of working with log transformed data appears to be the best method of handling lognormal data. This paper will discuss primarily the two parameter lognormal case, with some discussion of the three parameter lognormal, but no discussion of other methods of transforming data, such as disjunctive Kriging.

Jan 1, 1982

By C. Anim-Sackey, R. K. Amankwah

Some large-scale mining companies in Ghana have adopted proactive management strategies in dealing with small-scale (galamsey) miners who have encroached on their concessions. This has been mainly achieved by ceding portions of the concessions held by the companies to the Minerals Commission of Ghana for licensing to the small-scale miners. This development has created an amicable relationship between the mining companies concerned and the galamsey miners in their host community. Ghana’s small-scale gold and diamond industry The small-scale gold and diamond mining industry in Ghana has existed for many centuries as an informal sector. Since the regularization of the activities of small-scale mining in 1989, two types of small-scale miners have emerged — legal and illegal.

Jan 1, 2004